PDF datasheet
Contents
1. be for any laser LED source 1 ST 3 FC any combination of FC APC and FC PC Duplex LC we modify from SC interface by adding a label and unused adapter then front panel does not look so good O O O O Power on keylock switch Power on green LED Individual Laser enable button switch Laser enable green LED in each channel In each DWDM channel there is also an individual A 0 8nm button switch A 0 8nm LED A alarm LED Rear panel 9 18 V 1A DC input Typical 12V 1A The product comes with small external wall mount power supply its AC plug type will fit the wall socket of AC voltage in your country Input 100 240VAC 47 63Hz Please tell us your preferred AC plug type Our available AC power plug types are A C G I see 5th 9th photos below Type A see 5 6th photos at website is most popular one used in North and Centra America China Japan Taiwan and Thailand We will give you type A power supply by default We can give you all four types but we may have to change to a little larger packing box with little higher shipping fee Overall dimension 21x21X8 cm excluding power supply 32x27x14 cm packed Net weight about 1 6kg including power supply Enclosure material Aluminum at rear panel and side extrusions steel at top and bottom covers copper at front panel So whole enclosure is EMI shielded only with several small holes at front rear panels Two plastic bezels over front and real pan2. tunable over two 100GHz spaced channels n n 1 by pressing the button switch on front panel Very stable output power Automatic power control Temperature controlled cooled laser 9 125um singlemode fiber Integrated optical isolator Typical 2MHz 5MHz narrow linewidth Note DWDM 3mW 1559 79nm DFB laser is uncooled and does not offer features above Customized ImW 5mW 10mW 20mW laser sources do not support wavelength selection over 2 channels Non DWDM light source features Low cost lower output power still stabilized power by APC loop but less power stability since there is no TEC mostly less wavelength accuracy since there is no temperature controller mostly Choosing from following light source 0 85um MMF laser in ST adapter 1 3lum MMF LED in ST adapter 1 3lum MMF FP laser in ST adapter 1 3lum SMF FP laser in FC adapter 1 3lum SMF DFB laser in FC PC or FC APC adapter 1291nm 1611nm CWDM wavelength SMF DFB laser in FC PC or FC APC adapter 1 49um SMF DFB laser in FC PC or FC APC adapter 1 5lum SMF DFB laser in SC APC adapter 1 55um SMF DFB laser in FC PC or FC APC adapter 1 55um SMF LED broadband source in FC PC or FC APC adapter 3 FiberPrime Front panel Portable 4 Channel Laser Source Instrument 4 fiber adapters on front panel Fiber adapter options o 4FC any combination of FC APC and FC PC 2 ST 2 FC any combination of FC APC and FC PC 4 SC any combination of SC APC and SC PC It can
3. will get 4 channel laser source instrument with total cost 370 50 100 150 150 820 Note One laser instrument offers 4 output channels by default If you leave some channel blank no fiber adapter will be installed for that channel The instrument will be shipped without a laser in that channel Fiberprime may fill the empty slot at a later date if you desire FiberPrime Portable 4 Channel Laser Source Instrument Average optic 1h warm up power output Power stability i Cock 3 3 3 Light Source nm nm dB dB m 7 79 er eE gt e M o E O 2 no no no T 5 D z 2 etr gt m fo D fe gt a o D oo o Q oO o 10 jO a 10 O o o jo jo o J 830 860 35 lt 0 02 lt 0 85 1270 1380 1274 1356 1274 1356 1480 1500 1480 1500 1502 1518 1530 1562 _155um 58 typ rms lt 2 5 rms lt 2 5 rms aa ot stabilized powe 45 typ stabilized power 2 2 e e e DWDM 1mW DFB laser A itu Type A 360 C band lt 0 130 1 UI lt n 2 AN 2 0 eo 2 e V e h o 1 o A Jn Joa iIo juje ea O N Yes Yes ae 004 BN DWDM 5mW DFB laser A itu Type A Less acurate A 460 C band lt 0 130 DWDM 5mW DFB laser itu Type B More acurate A 580 C band lt 0 065 i U 3 z U 3 Oo i al al ss wo ve Y Y Y Air A Atr DWDM 1mW DFB laser A A T Type
4. 196 2 0 11 FiberPrime DWDM ImW DEB laser available qty on Sept 26 2013 Portable 4 Channel Laser Source Instrument ITU Wavelength Frequency Avail ITU Wavelength Frequency Avail Channel nm THz Qty Channel nm THz Qty 17 1563 86 191 7 0 40 1545 32 194 0 18 1563 05 191 8 0 41 1544 53 194 1 0 19 1562 23 191 9 0 42 1543 73 194 2 0 20 1561 42 192 0 43 1542 94 194 3 0 21 1560 61 192 1 0 44 1542 14 194 4 1 22 1559 79 192 2 0 45 1541 35 194 5 0 23 1558 98 192 3 0 46 1540 56 194 6 0 24 1558 17 192 4 0 47 1539 77 194 7 0 25 1557 36 192 5 0 48 1538 98 194 8 0 26 1556 55 192 6 0 49 1538 19 194 9 0 27 1555 75 192 7 m 50 1537 4 195 0 28 1554 94 192 8 2 51 1536 61 195 1 0 29 1554 13 192 9 25 52 1535 82 195 2 0 30 1553 33 193 0 53 1535 04 195 3 0 31 1552 52 193 1 26 54 1534 25 195 4 0 32 1551 72 193 2 0 55 1533 47 195 5 0 33 1550 92 193 3 0 56 1532 68 195 6 1 34 1550 12 193 4 0 57 1531 9 195 7 0 35 1549 32 193 5 38 58 1531 12 195 8 B 36 1548 51 193 6 2 59 1530 33 195 9 0 37 1547 72 193 7 0 60 1529 55 196 1 38 1546 92 193 8 0 61 1528 77 196 1 0 39 1546 12 193 9 0 62 1527 99 196 2 0 12
5. 7 1531 9 195 7 28 35 1549 32 193 5 2 58 1531 12 195 8 0 36 1548 51 193 6 1 59 1530 33 195 9 44 37 1547 72 193 7 15 60 1529 55 196 0 38 1546 92 193 8 0 61 1528 77 196 1 0 39 1546 12 193 9 1 62 1527 99 196 2 0 10 FiberPrime Portable 4 Channel Laser Source Instrument Type B DWDM 5mW DFB laser available qty on Sept 26 2013 ITU Wavelength Frequency Avail ITU Wavelength Frequency Avail Channel nm THz Qty Channel nm THz Qty 17 1563 86 191 7 0 40 1545 32 194 0 18 1563 05 191 8 0 41 1544 53 194 1 0 19 1562 23 191 9 21 42 1543 73 194 2 16 20 1561 42 192 0 43 1542 94 194 3 21 1560 61 192 1 0 44 1542 14 194 4 17 22 1559 79 192 2 50 45 1541 35 194 5 0 23 1558 98 192 3 0 46 1540 56 194 6 0 24 1558 17 192 4 14 47 1539 77 194 7 7 25 1557 36 192 5 0 48 1538 98 194 8 0 26 1556 55 192 6 0 49 1538 19 194 9 3 27 1555 75 192 7 50 50 1537 4 195 0 28 1554 94 192 8 0 51 1536 61 195 1 0 29 1554 13 192 9 32 52 1535 82 195 2 4 30 1553 33 193 0 53 1535 04 195 3 0 31 1552 52 193 1 0 54 1534 25 195 4 20 32 1551 72 193 2 47 55 1533 47 195 5 0 33 1550 92 193 3 0 56 1532 68 195 6 0 34 1550 12 193 4 63 57 1531 9 195 7 25 35 1549 32 193 5 0 58 1531 12 195 8 0 36 1548 51 193 6 0 59 1530 33 195 9 17 37 1547 72 193 7 19 60 1529 55 196 0 38 1546 92 193 8 0 61 1528 77 196 1 0 39 1546 12 193 9 3 62 1527 99
6. C Most acurate A 530 C L band lt 0 0 DWDM 5mW DFB laser A iT Type C Most acurate A 630 C L band lt 0 0 DWDM 10mW DFB laser A Tu Type C Mostacurate A 740 C L band lt 0 03 10 DWDM 20mW DFB laser A itu PM fiber Most acurate A 850 C L band lt 0 03 13 lt Note 1 Lasers with TEC will offer faster warm up and better power wavelength stability Note 2 For 1 55um 0dBm non DWDM DEB lasers the wavelength specification is 1500 1580 But we will pick wavelength within C band 1530 1562nm 7 es o es 10 e es 10 e es 10 e es 10 es es 10 es es 10 es es 10 es es Y Y FiberPrime Portable 4 Channel Laser Source Instrument See detailed available qty and price in the table at the end of website description For example price of DWDM 5mW DFB lasers around 1550nm is higher than 460 CWDM laser around 1551nm is over 200 Other CWDM wavelengths might be available but takes longer time and may apply higher price Each DWDM laser channel of standard products actually can cover two 0 8nm spaced wavelengths by pressing lambda 0 8nm on front panel so most of ITU wavelengths are in stock If you cannot see required wavelength we can get for you in a few days e g 5SmW ch 21 23 26 50 53 55 ImW ch25 The price would be different depending on our suppliers and shipping cost We can also make customized wavelength for you at longer lead time and extra cost Optical Specifications of Standard DWDM D
7. FB Laser Parameter Symbol Minimum Typical Maximum Average optical power output Pavg Default 5mW version 6 dBm 7 dBm 8 dBm 1mW low power version 0 5 dBm 1 dBm 2 0 dBm Power stability after 1 hour warm up 15min ambient T constant 0 01 dB 8 amp h AT 41 C 0 004 dB 0 03 dB Center wavelength range 1528 77 nm 1563 86 nm Center wavelength accuracy Type A laser 20 pm 90 pm 130 pm Type B laser 20 pm 20 45 pm 65 pm Wavelenei stability d after 10 minutes warm up Side mode Suppression Ratio SMSR 30 dB Line Width 3dB full width 2 5 MHz 10 MHz Optical isolation 30 dB 35 dB 50 dB Note Output power definitions and measurement per ITU T recommendations G 957 Note Minimum and maximum parameters are specified at room temperature Note Upon your request we can add extra isolator if you need keep stable output power in special environment When you test laser output power by some type of optical power meter such as optical head 4 optical power would be reflected back to laser and may make laser power less stable According to our test the last digit in power meter 0 001dB resolution in HP 8153A meter may randomly oscillate and tester may not be able to read last digit easily Choosing fiber angled APC connector or adding extra isolator can significantly improve power stability Fi berPrime Portable 4 Channel Laser Source Instrument Ordering Information
8. FiberPrime Fiberprime Inc Portable 4 Channel Laser Source Instrument www fiberprime com Tel 1 613 5964030 Email info fiberprime com Fax 1 613 8289398 Portable 4 Channel Laser Source Instrument in Small Benchtop User Manual QLDS N series version 1 0a March 26 2014 FiberPrime Safety Warning Portable 4 Channel Laser Source Instrument Do not under any circumstances look at the output of the unit through collimating or focusing optics unless the unit is turned off Do not look into the end of an optical cable attached to the optical output when the device is operational The invisible laser radiation of this optical instrument will increase eye hazard Use the utmost care when changing inspecting or cleaning any optical connectors Do not enable the laser when there is no fiber attached to the optical output connector The laser is enabled by pressing the Enable Laser button above the optical output connector on the front panel of the instrument The laser is on when the green LED on the front panel of the instrument is lit Laser Safety and Electrical Compliance e Class 1 laser product for standard products Max permissible output power around 1550nm 136mW Max wavelength range 1525 1565nm Exception Class 1M for customized 20mW laser o Complies with IEC 60825 1 60825 2 laser safety standards o Complies with 21 CFR 1040 10 except for deviations pursuant to Laser Notice No 50 dated J
9. Part number QLDS N WL1 P1 WL2 P2 WL3 P3 WL4 P4 A1 A2 A3 A4 N total channel count from 1 to 4 WLI channel number or wavelength of output 1 P1 channel 1 output power in dBm WL2 channel number or wavelength of output 2 P2 channel 2 output power in dBm WLS3 channel number or wavelength of output 3 P3 channel 3 output power in dBm WL4 channel number or wavelength of output 4 P4 channel 4 output power in dBm Al to A4 FP for FC PC FA for FC APC SP for SC PC SA for SC APC LP for LC PC interface from ch to ch4 Example Part number for two lasers type A 7dBm 1531 12nm ITU ch58 type B 7dBm 1541 35nm ITU ch45 with FC APC interface QLDS 2 58 7A 45 7B FA FA Part number for four lasers 10dBm 0 85um MMF laser 0dBm 1 3um MMF FP laser type A 7dBm 1531 12nm ITU ch58 type B 7dBm 1541 35nm ITU ch45 with two ST adapters for chl and ch2 two FC PC adapters for ch3 and ch4 QLDS 4 0 85 10 1 3 1MFP 0 58 7A 45 7B ST ST FP FP Fiberprime Inc Tel 1 613 7214921 E mail info fiberprime com Fax 1 613 8289398 Ottawa Ontario K2H 1A1 Canada All information contained herein is believed to be accurate and is subject to change without notice No responsibility is assumed for its use Fiberprime Inc reserves the right to make changes without notice to product design product components and product manufacturing methods Some specific combinations of options may not be available Please contact Fiberprime Inc for more info
10. els for nice look and protection Standard operating temperature from 10 to 40 C degree It can be extended to from 15 to 70 C degree upon request Standard package includes Enclosure with laser modules One wall mount power supply AC plug is type A for most countries One FC UPC FC UPC UPC is compatible with PC fiber jumper for each laser channel Or other connector type to match the front panel adapter One FC adapter for each laser channel Or other adapter type to match the front panel adapter Small qty of swabs to clean internal fiber connectors at front panel Wilshire PN 1002 Our test data of output power and wavelength after at least 30 minutes warm up FiberPrime Portable 4 Channel Laser Source Instrument Inspection Before shipment this unit has been found to be free of defects The instrument s model part number serial number and configuration are found on a label located on the back of the unit The instrument s history is filed at the factory by part number and serial number Assembling Instrument after you receive the instrument e Connect each fiber patchcord to the adapter on front panel Please Do Not screw FC connector into FC adapter very hard which may make connector dirty Please always keep fiber jumpers connected on front panel adapters Put on the adapter at other end on each fiber jumper e Plug in the wall mount power supply Getting Started e Insert the key in
11. hip same or next day Add a controller 0 85um MMF laser source 1 31um MMF FP laser 1 3lum SMF DFB laser source and 1 55um SMF DFB laser source to webstore shopping cart then you will get 4 channel laser source instrument with total cost 370 50 100 150 150 820 See the 4th photo below in website Example B in stock ship same or next day Add a controller 4 CWDM lasers to webstore shopping cart then you will get 4 channel laser source instrument with total cost 370 4x 200 1170 extra 80 if you choose 1551nm Example C in stock ship same or next day Add a controller 1554 13nm type A DWDM 7dBm laser to webstore shopping cart you will get 1 ch laser source instrument with total cost 370 475 845 Example D in stock ship same or next day Add a controller 27 1555 75nm type B and 1562 23nm type A DWDM 7dBm lasers to webstore shopping cart then you will get 2 channel laser source instrument with total cost 370 580 460 1410 Example E ship in 3 day Add a controller 1562 23nm 1550 12nm 1540 56nm 1531 9nm DWDM 7dBm lasers to webstore shopping cart then you will get 4 channel laser source instrument with total cost 370 460 520 460 460 2270 Almost same as 1 two photos below except the adapter shape is square Example F ship in 3 day Add a controller 0 85um MMF laser source 1 3lum SMF DFB laser 1 49um SMF FP laser source and 1 55um SMF DFB laser source to webstore shopping cart then you
12. rmation Fiberprime Inc All rights reserved Rev 001a 3 2014 Printed in Canada FiberPrime Portable 4 Channel Laser Source Instrument Appendix CWDM SMF DFB laser available wavelengths and qty on Sept 26 2013 WL nm Qty 1611 12 1591 11 1571 10 1551 2 1531 16 1511 26 1491 15 1471 14 1451 46 1431 9 1371 6 1351 4 1331 1 1291 4 Note Wavelength accuracy specification of CWDM DFB laser is max 6 5nm typical 1 5nm Type A DWDM 5mW DFB laser available qty on Sept 26 2013 ITU Wavelength Frequency Avail ITU Wavelength Frequency Avail Channel nm THz Qty Channel nm THz Qty 17 1563 86 191 7 0 40 1545 32 194 0 18 1563 05 191 8 0 41 1544 53 194 1 0 19 1562 23 191 9 55 42 1543 73 194 2 11 20 1561 42 192 0 43 1542 94 194 3 0 21 1560 61 192 1 wait 44 1542 14 194 4 5 22 1559 79 192 2 51 45 1541 35 194 5 0 23 1558 98 192 3 wait 46 1540 56 194 6 1 24 1558 17 192 4 14 47 1539 77 194 7 9 25 1557 36 192 5 0 48 1538 98 194 8 1 26 1556 55 192 6 wait 49 1538 19 194 9 13 27 1555 75 192 7 13 50 1537 4 195 1 28 1554 94 192 8 0 51 1536 61 195 1 0 29 1554 13 192 9 30 52 1535 82 195 2 5 30 1553 33 193 0 53 1535 04 195 3 wait 31 1552 52 193 1 0 54 1534 25 195 4 5 32 1551 72 193 2 3 55 1533 47 195 5 wait 33 1550 92 193 3 1 56 1532 68 195 6 5 34 1550 12 193 4 30 5
13. to key lock switch on front panel e Turn on the key lock switch on front panel e Press EDFA ENABLE button on front panel Cleaning optical connectors After optical connectors plug in and pull out many times on adapters the connector may not be easily cleaned so we highly recommend that you always keep external fiber jumpers connected on front panel and only clean the jumper connectors of far ends You may need clean internal connectors on front panel in future please use Fiber Optic Cleaner Pen designed to clean the internal connector through the adapter of equipment panels Warranty one year after delivery See http www lightwavestore com warranty 20and 20technical 20support htm Note Never open the instrument enclosure or warranty will be voided FiberPrime Configuring a 4 channel source Portable 4 Channel Laser Source Instrument You need choose one controller unit and to 4 lasers from the table at the end of description 1 Add controller unit only without laser light source 370 to shopping cart Fiber adapter options a 4 FC b 2 ST 2 FC c 4 SC any combination of PC or APC SC APC is only available for single mode fiber d 1 ST 3 FC f Other adapter types and combinations longer lead time may apply Note FC can be any combination of FC APC and FC PC FC APC may not be available for multimode fiber 2 Please choose individual lasers from channel to channel 4 Example A in stock s
14. une 24 2007 e Complies with CE and other standards for electrical safety and EMI The external AC DC power supply comes with safety certificate from manufacturer The instrument only needs low voltage 12 VDC power supply While standard output sources fall within the class 1 laser rating Class 1M for customized 20mW lasers the system was designed to meet 3B laser class requirements The power switch is a keylock system to prevent accidental or unwanted use Each source has its own enable button allowing the user to choose the light source they wish to be active Each channel includes a green LED indicator to easily determine its current state There are also aperture label and laser warning label FiberPrime Portable 4 Channel Laser Source Instrument Description Portable stabilized 4 Channel Light Source Instrument comes with 4 laser and or LED broadband light source output channels choosing from DWDM lasers or non DWDM light sources Small light portable and also benchtop It can be placed on either low workbench or high shelf Stabilized and low noise laser driving and applicable temperature control circuitry DWDM laser source features 5mW stabilized output 1mW version is also available Both are based on high reliable JDS or Lucent laser and telecom grade circuitry Higher power is available at longer lead time Any wavelength of C band ITU DWDM 100GHz channels is available most wavelengths are in stock Wavelength
Download Pdf Manuals
Related Search