User`s Manual (THA-MA/MA2)
Contents
1. PATE 2372 BIKE x A BZ BE EAR P Wire Color HONDA vey M THA MA1 MTC 2 E ection F E Brown ail ai Connector i Brown r MTC 2 Wire leading from product 2 Connect for Adaptor Power For THA MA1 Using one of the supplied cut connectors connect the wire of the Adaptor to the GE wire of the 3 drive For THA MA2 Using one of the supplied cut connectors connect the wire of the Adaptor to the clutch switch IGN wire 3 Connect to the Brake Switch Signal Common for both THA MA1 and THA MA2 Cut the wire of the 3 drive at an appropriate place Using the supplied connectors attach the female connec tor to the brake switch wire and the male connector to the 3 drive wire Refer to Reference 1 How to use the Connectors 3 3 drive D gt 4 Male Female to Brake Connector Connector Switch Connect the wire and the wire from the adaptor to the just attached connectors Clutch Adapter 3 drive D _on to Brake Switch Connect for Earth Common for both THA MA1 and THA MA2 Using one of the supplied cut connectors connect the wire of the Adaptor to the EJEtdg wire of the 3 drive Refer to Reference 2 How to use the Cut Connectors 12V with key ON Confirm the Connection Connecting the tip of the Voltage Detector to wire of Clutch Adaptor and if it s 12V LED Lamp ON2. connector Remove about 10 mm of the cable Crimp these places casing Vy 10 mm CHa Peel off of the vinyl Insulate with vinyl tape TA cover at the end of the product s wire Affix the male sleeve to the places as mentioned above a o 10 mm Turn back the tip of the wires CHE Wrap around both wire coils When crimping please use crimpers or use pliers to bend and then solder together X After connecting the male and female connectors make sure to firmly twist the male sleeve inside the female sleeve Connect the male connector to the end of the cable rie le Connector Connecting The Wires 1 A e g HONDA CIVIC Wiring Chart Connect to the Clutch Switch Signal phar Common for both THA MA1 and THA MA2 After confirming the connection position for your model car as shown on the attached sheet Wiring Chart MT connect the Brown or Green wire using one of the supplied cut connectors X Some models may have two clutch switches please connect to the same connector as listed under Connector Design in the Wiring Chart MT Refer to Reference 2 How to use the Cut Connectors For customers using THA MA1 make sure to insulate the wire Brown or Green left unconnected
3. product will not run properly half way will cause the engine rotation to increase oil and dust a J Troubleshooting Trouble Possible Causes Possible Solutions AUTO CRUISE does not Operate Each wire may have been improperly wired or there is a poor connection Please reconfirm whether wiring and connections are correct or not switches to throttle controller AUTO CRUISE is automatically deactivated and the display Each wire may have been improperly wired or there is a poor connection Please reconfirm whether wiring and connections are correct or not deactivate The clutch pedal is pressed down but AUTO CRUISE does not The clutch pedal is not fully pressed down all the way Make sure to press down fully on the clutch pedal The or Green wires may have been improperly wired or there is a poor connection Please reconfirm whether wiring and connections are correct or not PIVOT CORPORATION 87 3 Shimookada Okada Matsumoto shi Nagano 390 0313 Japan TEL0263 46 5901
4. when pressing the brake pedal or the clutch pedal connection is correct It s OV LED Lamp OFF when releasing the Refer to User s Manual of 3 drive series pedal Installing The Product Use the double sided tape included to fasten the units into positions not usually affected by water How to Install w 4 Double sided lt lt tape Included Please be sure A to bundle away all wires with tape etc While in use if wires become free they may interfere with driving and cause accidents Also wires which are smashed or crushed may result in a short and can be extremely dangerous After installation make sure to carry out INITIAL SETTINGS and Speed Pulse Settings Make sure to carry out all Initial Settings and Speed Pulse Settings of the 3 drive User s Clutch Voltage Detector I Test Drive After having fully read sections Basic Operation and How to Operate of the 3 drive User s Manual take a test drive If while in AUTO CRUISE pressing down on the clutch pedal deactivates the AUTO CRUISE function the adaptor is working properly A Usage Note In some car models it is necessary to fully press down on the clutch to activate the clutch switch signal When deactivating AUTO CRUISE make lt pe Clean to Manual If these settings are not carried out the sure to fully depress the clutch Pushing down only Deis
5. USER S MANUAL Manual Transmission Clutch Adaptor edh A A THA MA1 MA2 As of March 2015 No 5 Product Number THA MA1 MA2 This product is a Manual Transmission Clutch Adaptor specifically designed for use with our 3 drive Series Cruthro AWARNING Improper use or disregard of these warnings may result in the injury or death of people Do not use in conjunction with products from other manufacturers In such a case PIVOT Corporation accepts no responsibility in any manner whatsoever for any damage or trouble direct or indirect A CAUTION Improper use or disregard of these warnings may cause injury to persons damage the product and or other things When installing this product we recommend that if technical knowledge becomes necessary please consult a qualified mechanic PIVOT accepts no responsibility whatsoever direct or indirect for any troubles that may occur if this product is modified or used in conjunction with another company s product Do not use electrotap Please check the contents of the package Wiring USER S Chart D 64 CA AF Pg LP MANUAL Mt FJ si A Cut Male Connector Female Connector pa Double sided User s Manual Wiring Chart MT Clutch Adapter Zip Tie Tape 9 i P Connectorsx 3 Male Sleeve Female Sleeve P j25x35 mm This Book in Japanese If the clutch switch wiring has been changed in any way to connect to a d
6. ifferent product make sure to return it to its original condition If the product is not installed properly it may result in poor operation including that the product does not work or the AUTO CRUISE function does not run properly X For details about the connection position for the clutch switch signal please see the attached sheet Wiring Chart MT K Use Connector H Basic Wiring THA MA1 E Use Cut Connector E Use Cut Connector K Use Connector THA MA2 Clutch Switch Signal X1 or Brown Clutch Switch Signal Clutch Adapter Clutch Adapter AN Q i Gray Purple Gray Purple Clutch Clutch Pedal Pedal 3 drive to Brake 3 drive to Brake Switch Switch x1 Cut off the insulation of the tip of the codes Brown and Green code which you need to connect then bundle the extra code Reference 1 How to use the Connectors Figure is shown using a male connector Reference 2 How to use the Cut Connectors Crimp down with crimpers to make sure that the inner wires are firmly connected to the Close tightly with cut connector Peel off of the vinyl cover at connection Pull the cable through the male sleeve oe Male sleeve Wire inner part of the connector and that the Ld SS cable section is connected to the outer part 10 mm of the
Download Pdf Manuals
Related Search