A.2 Environmental Specification
Contents
1. 1 iS O 60 120 T min A 5 A 7 2 Trumpet curve The deviation of infusion rate in short term pAf Sampling rate 25ml h Sampling intervals A t 0 5 minutes Observation window duration pAt 2 5 11 19 31minutes Max deviation in Provisions Duration EPmax 9 Min deviation in Provisions Duration EPmin 96 Average percentage for flow rate deviation A 96 Percentage Error of Flow 96 2 5 1 19 31 Observation Interval min e Infusion accuray does not reflect the clinical criteria such as patient s age weight and the usage of medication e Infusion accuracy may be affected by the machine working environment such as pressure temperature humidity and other components used for transfusion A 6 B EMC GUIDANCE AND MANUFACTURER S DECLARATION This infusion pump meets the EMC standard EN 60601 1 2 Note Using the acessories sensors and cables beyond the specified range may increase the electromagnetic emission of infusion pump or reduce the electromagnetic immunity e The infusion pump must not be closed or stacked with other equipments When infusion pumps have to be used with other equipment closely observe them to ensure normal operation e It needs special protection for the EMC of the infusion pump And the installation and maintenance of machine should be under the following EMC environment Infusion pump should not be used with MRI magnetic resonance imagin2. ooocococccocncccnccccccocncconocanononoss 5 11 5 7 Drop Rate Function Optional oooccconncocnococococncocnconcnnnononononononanononononnns 5 11 SA Starting Drop Rate FUNCION dd 5 12 5 7 2 Setting Drop Rate for infusion tube occcoccccccncccncconncocnnocncnnnnnonnnonnns 5 12 5 0 Language OWItChIhg soe ii idas 5 13 6 Alarms srir m E 6 1 8 1 OVEIVIEW ii loto 6 1 OZA YD c e a a e a E 6 1 6 21 AUdIblS AlI Mos E lien 6 1 A Use ee ea ene la bees 6 1 6 3 Alarm Countermeasures cccoccccccccocccconoconnnncnnnnncnnnnnnnnonanonnnnnnnonannnnrnnnnnenaninaninns 6 2 A Product SPEEIICAHON een nenne A 1 ANS SP o e nas Dawe eee A 1 A 2 Environmental SpecifiCatiON cooccocccoccconcocncocnconoconononoonnnorocoronanonononcnnnnnos A 1 A 3 Power Supply Specification eee enne nnm nnnm rins A 2 A 4 Hardware SpecifiCatiON oocooocooccconcconcconoocnconocanonanononnnronononononnncanonanenanons A 2 A 5 Basic Parameters of Infusion Pump cooccccccccccocccoccconncnncocnnarccnnocanononconnnaronannns A 3 A 6 Pressures that trigger a occlusion alarm maximum alarm delays and permissible maximum volumes per INTUSION cocccocccoccccccocnconnconnconnonnnonnnornnnnonononononcncnnocanonancns A 4 A 7 Int usiognACculacy Table accionista A 5 B EMC GUIDANCE AND MANUFACTURER S DECLARATION B 1 C Alarm Informal ee t cs C 1 CT Alarm Information siu euch re On eet the ke dtes
3. Install the two ports of infusion tube to the bottoms of the pump groove 3 Place the infusion tube to the bottom of 4 Pull down the door lock after the pump groove straightly and horizontally installation 4 3 NWARNING e Pull down the door lock after installation of infusion tube properly when the pump is on When green indicator lamp is on it means the infusion tube is proper installation Otherwise infusion tube need reinstallation e When use the same infusion tube change the part of pipe installed in groove of machine every 4 hours The IV set should be discarded after 24 hours of continuous using e Infusion tube is loose or pulled too tightly which may cause abnormal infused volume e The double thickness of the infusion tube should be between 0 8mm 1 2mm Outer diameter should be between 3 5mm 4 5mm Otherwise its accuracy can not be guaranteed which may cause severe injury to patients NCAUTION e After installation of infusion tube and before infusion please check if there is any leakage If so please check the machine and installation of pipe 4 2 3 Setting Infusion Parameters 1 Press the key to make the pump in stop condition 2 Press the key E to enter setting interface of infusion parameters Press the key or to select the setting items Then press the key to make the setting item adjustable Now press the key or to adjust the value press the key to save the parameter
4. Upward value increase key Select needed parameter or increase the values CLEAR key 2 3 12 13 14 Press this key to clear accumulated value under stop status Infusion mode Display current infusion mode Value Increment It could be used under value setting status Type of infusion tube Display current type of infusion tube A B C Status Icon Display current infusion status Stop Run KVO Bolus Power icon indicate the current power status When machine connect to AC power and battery is full capacity LCD displays plug When machine connect to AC power and battery is not full capacity LCD display battery charging icon When machine disconnect to AC power LCD display battery icon and its current battery capacity Door Lock Pull up the door lock to install or take off the infusion tube Push down the door lock to tightly clamp the tube The running indicator lamp is on if infusion tube is well installed when the door lock was pushed down Downword value decrease key Select needed parameter or decrease the values Confirm key Put the parameters into an adjustable condition or save the parameters SET key To select infusion mode START BOLUS In stop status if the infusion tube is correctly installed press this key to start infusion During infusion process keep pressing this key to start bolus function If the flow rate is less than settled bolus rate the pump shall infuse a
5. The serious low battery alarm will be eliminated when the pump is connected to the AC power e 8 14 hours will be needed to fully charge the battery e Please discharge the battery every three months to prevent damage of the battery if the product is not used very often e Battery is a consumable part Please replace it when it is exhausted Incase the battery needs to be changed please contact the local distributor or manufacturer 2 4 2 Battery Guidelines The life span of the battery depends on its usage frequency and environment If proper usage and maintenance are adopted its life span is 3 years Otherwise its life span will be deducted The battery shall be replaced every 3 years For safety usage and capably extend a longer battery life please follow the battery instruction Annual battery inspection is needed Before the pump is sent for maintainance purpose or you doubt the battery is the causing reason the battery checking is needed Optimize the battery every three months of use or storage or once the running hours of battery is significantly shortened Using 1C current 1C current shall be larger than the working current of the working plate the max charging current of the protection plate is the working current of protection plate 8 4V voltage limiting to charge the battery for 0 5hour in order to guarantee the battery is stored with electricity 2 7 NWARNING e Using the battery provided by the manufa
6. 2 IF TONE Panel A 2 3 222 Back diesen o A a 2 5 Z S elPiici iMBIIe iem TEE 2 6 2A A dec e 2 6 2 4 1 OVER o 2 6 2 4 2 Battery GUIAeliNes oocccoccccocccocncconocanicncnoncnocononnnnonanonanonnnnononenaninons 2 7 24 3 Battery Maintenance aaa 2 8 24 9 Tl Conditioning a Bater hooked aioe te a ae 2 8 2 4 3 2 Checking a Battery ceiien iina ee 2 8 2 4 4 Battery Recycling 1 esee nenne 2 9 3 Installation and Maintenance u 2u0200 000n0nn0nnunonunnunnun nun nun nun nun nnn nnn nnns 3 1 3 1 1NSlallall ON eben dui cu Ul ada eer de cri caa e desc Vu by na hs idu tva ef da UNES HORE 3 1 3d O tof BOX Audi OOBJA senden 3 1 3 1 2 Environmental Requirements occocccccccccccnconiocnccnconnonnnnncononconnocancononons 3 2 3 1 3 Power Supply Requirements eene nnnm enne nne nr nes 3 2 3 1 4 FIX Infusion Pump a a E ANG 3 3 3 1 9 Install POWer Collie 3 4 3 1 6 Installation of Drop Sensor Optional 3 4 3 2 IRR UU I T TM 3 6 9 2 MSDECION sen uE dut Due adm PUn iate 3 6 322 CCAM G ecc 3 6 3 2 3 Preventive MaintenanCe cooccoccccccoccocicoonconconococnnononnnoncnoncnnonnnonocanennenoss 3 8 3 2 4 Pollution Free Treatment and Recycling sssse 3 8 4 ODES FAT OM Gulde mee ER EU 4 1 A 1 Operation FIOW GRAM tiswsissssica ter aaa 4 1 A Da plo o EDS A ne ER Beinen 4 2 42 1 Start INFUSION PUN
7. i 4 2 4 2 2 Install the Infusion Tube occoconccocncccncccnocococonnccononononncnonanonanonanonnnnos 4 3 4 2 3 Setting Infusion Parameters coooccconccocncocnccocononnccncononnnonnonanocnnnonaninons 4 4 4 2 4 Clearing Accumulated Volume ccooccccccccocccccnnccnccocnnnnncnononnnnnncnonanonons 4 5 422 0 Starting IMPUSION succ ci eani ocu a s dan nee orent cd rani 4 5 4 2 6 Infusion Completed coocccocccocoocccoccconccononcnonnocanonanonanoncnnarocanononennncnnos 4 5 4 2 7 gei er PER 4 6 5 Function and Interface oed are 5 1 5 1 Infusion Mode and Parameter SettinQ ocooocccocncocnccccnconnccnncnncnconnnnnnonnnnnos 5 1 9 11 Setting Flow Rale 2 2 ee ala Da 5 2 5 1 2 Selling Preseb OM cie seni me torre Sca oret tiges tems ect iutan d PH tuU EdE 5 3 5 1 3 Setting Other Parameters occoocccccccoococonncocnnocnonoconanonnanonanonnnnnonenaninoss 5 3 5 2 Advanced SiN een 5 4 9 9 UNIOCKING dia 5 5 9 4 otaftirig Bolus Function BOlls ann ln 5 6 5 5 Pressure Sensor Calibration 002200222022400200000n0 Benno nennen nnne nennen 5 6 5 6 Changing Infusion Tube Brand u022202220022000enennnnnnnnennnn nennen nenn 5 8 526 1 Selection OL IV SE use ee 5 8 5 6 2 Setting Inf slorrACeul aC iue ie te tar ae 5 9 5 6 3 Setting Occlusion Level ooocccocccocccccnoccnccocncoononanicononnonocanonaninnnnos 5 10 5 6 4 Setting Air Bubble Filter Level
8. lamp information etc Alarm occurs in case of completed infusion accidental circumstance machine abnormal installation error of infusion tube or machine malfunction that result in abnormal infusion NWARNING e There is a potential hazard for the same or similar devices to use different preset alarm in any single area 6 2 Alarm Type The infusion pump will give visual and audible alarm to remind the users Among them the visual alarm and audible alarm will give in different ways to indicate the alarm types 6 2 1 Audible Alarm Audible alarm means when alarm be triggered the infusion pump will send audible alarm Single alarm Single alarm reminds circularly Multipal Alarm Alarm sounds frequently 6 2 2 Alarm Information Alarm information means when alarm be triggered the corresponding alarm information will be displayed in the status bar B I fanew alarm occurs audible and visual alarm will be triggered and the alarming text shall be indicated in a loop B The alarm shall be triggered when the pressure value exceeds the highest or lowest limit of the occlusion value setting The status bar of the infusion pump would display the corresponding alarm information when it alarms The alarm Categories are as follows B Air Bubble B Over B Occlusion 6 1 Infusion tube error Control abnormal 1 Control abnormal 2 Drop rate error No AC Low battery Battery exhausted Start prompt Door lock opened 6 3 Alarm C
9. mw it p J s Manual Infusion Pump Model iP 12B 0123 2012 2013 Shenzhen Biocare Bio Medical Equipment Co Ltd All rights reserved For this User s Manual the issue date is May 2013 Version 2 0 Intellectual Property Statement SHENZHEN BIOCARE BIO MEDICAL EQUIPMENT CO LTD hereinafter called Biocare bio medical owns the intellectual property rights to this product and this manual This manual may refer to information protected by copyright or patents and does not convey any license under the patent rights or copyright of Biocare bio medical or of others Biocare bio medical intends to maintain the contents of this manual as confidential information Disclosure of the information in this manual in any manner whatsoever without the written permission of Biocare bio medical is strictly forbidden Release amendment reproduction distribution rental adaptation translation or any other derivative work of this manual in any manner whatsoever without the written permission of Biocare bio medical is strictly forbidden r i iocare is the trademark registered or otherwise of Biocare bio medical in China and other countries All other trademarks that appear in this manual are used only for informational or editorial purposes They are the property of their respective owners II Responsibility on the Manufacturer Party Biocare bio medical reserves the final interpretation for this User s M
10. or liability for direct indirect or consequential damages or delay resulting from the improper use or application of the product or the use of parts or accessories not approved by Biocare bio medical or repairs by people other than Biocare bio medical authorized personnel This warranty shall not extend to Malfunction or damage caused by improper use or man made failure Malfunction or damage caused by unstable or out of range power input Malfunction or damage caused by force majeure such as fire and earthquake Malfunction or damage caused by improper operation or repair by unqualified orunauthorized service people Malfunction of the instrument or part whose serial number is not legible enough Others not caused by instrument or part itself IV Company Contact Manufacturer Factory Headquarters Website Tel Fax EC Representative Address Shenzhen Biocare Bio Medical Equipment Co Ltd 2 F West 4th Block Dayang Road South Fuyong Sub district Bao an District 518103 Shenzhen PEOPLE S REPUBLIC OF CHINA HAT35 7 F Block A Shenzhen Mingyou Industrial Products Exhibition 4 Procurement Center Baoyuan Road Xixiang Sub district Bao an District 518102 Shenzhen PEOPLE S REPUBLIC OF CHINA http www biocare com cn 0086 755 27960888 0086 755 27960643 Shanghai International Holding Corp GmbH Europe Eiffestra e 80 20537 Hamburg GERMANY Preface Manual Purpose This User s Man
11. phone s base stations and ground mobile radio receivers the antenna devices FM and AM radio television broadcast is unable to use pure theory for the accurate estimation In order to evaluate the electromagnetic environment produced by fixed RF transmitters we should consider method of electromagnetic field measurement If the measured field strength of working environment of infusion pump exceeded the stipulated RF level we must observe whether infusion pump can work normally Once abnormal situation was found we must take corresponding measures such as changing the direction of infusion pump or moving it to other places When the frequency range is between 150 k and 80 MHz the field strength shall be less than 3 V m B 3 Recommended Distance Between Infusion Pump and Portable Mobile RF Communication Equipment The infusion pump can be used in the electromagnetic environment where RF interference can be controlled In order to avoid electromagnetic interference the customer or user should ensure that the infusion pump and portable mobile RF communications equipment maintain the minimum recommended distance The following recommended distance is calculated according to the maximum output power of communication equipment The transmitters maximum output power If the transmitters maximum output power is not within the above range we can estimate isolation distance by corresponding equation in column P in the equation is the max
12. please do not use the infusion pump and immediately contact the distributor or our company 3 2 2 Cleaning The pump must be cleaned or disinfected with the materials and methods listed in this chapter Otherwise our company will not take the responsibility for any damage or accident caused by the cleaning and disinfection with other materials and methods 3 6 Our company will not take any responsibility for the effectiveness of the infection control with the following chemicals or methods Please contact the infection prevention department of the hospital or epidemic experts for the method of infection control Please keep your devices and accessories away from the dust and comply with the following provisions to prevent the device damage m Please dilute the cleanser and disinfectant in accordance with the manufacturer s indication or with their concentration as low as possible B Do not submerge the pump in the liquid B Do not dump the liquid on the device or its accessories B Prevent liquid from the pump body B Do not use the abrasive material such as steel wool or silver polishing agent and any strong dissolvant similar to acetone and acetone to prevent outer shell damaged NWARNING e Please turn off the power and disconnect the AC power supply before cleaning the device NCAUTION e Please turn off the power and disconnect the AC power supply before cleaning the device If the liquid is dumpted on the infusio
13. sensor or expose it to sunshine during infusion e Make sure that the medicine liquid filter is not clamped too tightly by the drop rate sensor 3 5 3 2 Maintenance NWARNING The hospital or medical establishment using this infusion pump must set up a complete maintenance plan Otherwise it may cause device failure or some unexpected consequence and even threaten the personal safety All the safety inspection or the maintenance work which involves the disassembling the device must be proceeded by the professional maintenance personnel The operation of any unqualified people may cause device failure and even threaten the personal safety Please contact the distributor or our company immediately if you find any problem of the pump 3 2 1 Inspection The pump must be given an overall inspection before use after 6 12 months continuous use or after maintenance or updating to ensure the normal operation and work The inspection standards are The environment and power supply meet the requirements The battery performance The power cord has no abrasion and is well performed in electric insulation Pass the leakage current test The devices and accessories have no mechanical damage The accessories used with the pump are specified The alarm system is well functioned No leakage after installation of the infusion tube The pump works well under all infusion modes If there is any pump damage or abnormal phenomena
14. the normal use of the pump during patients transfer or electricity fails in hospital The battery will charge itself automatically once the pump is connected to the AC power and in Power on situation The pump shall work with its battery in case of sudden electricity break down The battery shall provide the power for normal operation of the pump for a certain while once the battery capacity reaches the lowest voltage the pump will trigger a low voltage alarm every few seconds to notice the users after a certain while the pump shall trigger a serious low battery alarm with the battery indicator lamp flashes and a rapid and short alarming sound If the pump is working at this time it will stop infusion automatically and will not work until it is connected to the AC power The low battery alarm will be eliminated only after the pump is connected to the AC power 2 6 NWARNING e Keep the battery out of the reach of children e Use only the battery specified by the manufacturer NOTE e When the battery capacity is 0 and in low battery condition an alarm will be triggerd within a few seconds to remind the users of low battery Shortly after low battery alarm the pump shall trigger a serious low battery alarm the indicator lamp shall flash and the pump will give a rapid and short alarming sound If the pump is in working status it will stop infusion automatically and it can not be used for infusion until it is connected to the AC power
15. and Indicated Infusion rate preset volume accumulated volume battery information indicator pressure value AC power indicator etc Alarm information Over occlusion air bubble low battery etc State Indication Stop infusion bolus KVO Air bubbles measure The minimum air bubbles is 0 005ml at 50ml h he maximum pressure is 160kPa occlusion alarm pressure scope is 40 160 kPa the longest time of Infusion pressure E occlusion alarm is 2 mins at 25ml h the longest time of occlusion alarm is 12 mins at 5ml h A 3 A 6 Pressures that trigger a occlusion alarm maximum alarm delays and permissible maximum volumes per infusion Reference Actually measured value l l l Flow rate Alarm time High dose volume occlusion value of pressure intensity ml h Min ml Kpa Kpa a e CI a mn jene e Test condition of the above data e FLUKE IDA4 PLUS tester e Infusion tube brand Dragon Heart e The occlusion pressure value maximum delayed time and maximum dosage volume will be affected by test conditions A 4 A 7 Infusion Accuracy Table The accuracy chart is as follows indicating the infusion change from the beginning of infusion to steady infusion A 7 1 Accuracy Curve Q ml h It is based on the data from a two hours observation cycle Sampling rate 25ml h Sampling intervals A t 0 5 minutes Test period T 120 minutes Infusion rate Q m h DOM mee ee ee eii
16. anual Biocare bio medical reserves the rights to modify the User s Manual without further notice The modified parts will be present in the new edition of User s Manual Biocare bio medical is not responsible for any software and devices provided by non Biocare bio medical and distributors Biocare bio medical is responsible for the product safety reliability and performance on condition that all the following conditions are satisfied B Installation expansion readjustment improvement and maintenance must be operated by professionals authorized by Biocare bio medical B All maintenance involving replacement of spare parts and its accessories consumables should use the original sets or sets authorized by Biocare bio medical B Relevant electrical equipment meets national standards and requirements of this User s Manual m Please operate the product as per the User s Manual N WARNING e The device must be operated by professional clinicians or under the guidance of professional clinicians The users must receive adequate product training No unauthorized or untrained personnel should carry out any operation Ul Warranty THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE Exemptions Biocare bio medical s obligation or liability under this warranty does not include any transportation or other charges
17. as the current setting item by pressing the mG or on the interface of Advanced Setting and make it adjustable by pressing the oro as shown in Figure 4 7 Then adjust occlusion level by pressing the mG or Q2 and finally save it through pressing the key CD NOTE e The lower the occlusion level the higher the occlusion sensitivity is 5 6 4 Setting Air Bubble Filter Level Bed NO 0 KVO Rate 1 0 ml h BOLUS 1000mI Tube A Pipe Accuracy 30 Occ Val Mid Drop ML 20 AirLevel MAW or Figure 5 12 Select Air bubble filter Level as the current setting item by pressing the key or on the Advanced Setting mode interface and make it adjustable by pressing the key as shown in Figure 4 7 Then cyclically choose 1 2 3 or Off by pressing the key or O and finally save it through the key C NOTE e The higher the filter level the larger capacity the air bubble filtered is 5 7 Drop Rate Function Optional NOTE e This section Drop Rate function setting needs suport of software For more details pls consult the distributor that sells the product to you or the Menufacturer 5 7 1 Starting Drop Rate Function STOP In stop status press the key and the NO simultaneously on the mode setting interface to enter into the Advanced Setting interface and then the NC to turn to page 2 and press the key Or to select Drop rate as shown in Figure 4 4 Press the key to make it adjustable then the k
18. company Any infringement act such as falsification reproduction or exchanging by any means or in any form by any organization or individual is not allowed without permission 3 1 1 Out of Box Audit OOBA Before opening the box please check the package carefully to find if there is any damage to the products during transportation If there is any damage please contact the forwarder or our company immediately If the package is intact please open the package in right way take out the infusion pump and its accessories with care and check them out in accordance with the packing list Please examine if there is any mechanical damage to the pump and whether the package includes all things on the packing list Please contact our customer service department immediately if there is any inquiry NWARNING e Please keep the packing materials out of the reach of children The packing materials must be disposed in compliance with the local laws and regulations or the hospital policy on waste treatment NOTE e Please keep the packing case and packing materials for the future use e Please contact the sales agent or our company if any of the spare parts is missing when you open the package 3 1 3 1 2 Environmental Requirements The service environment of this infusion pump must meet the requirements in A 2 Product Specifications The service environment of this infusion pump should also be appropriately protected from noise vibration d
19. cturer e Please replace the battery once the battery is damaged or leaks e Damaged battery shall not be used e The used battery shall be returned to the distributor or manufacturer or be disposed according to applicable laws 2 4 3 Battery Maintenance 2 4 3 1 Conditioning a Battery Optimize the battery when it is used for the first time A complete optimizing cycle includes continuously charging until the battery is fully charged then discharge the battery until the pump powered off automatically Then charge the battery continuously again During the usage a regular optimize battery performance will extend its life span NOTE e The actual battery capacity will reduce after the battery is used for some time If the battery capacity is shortened obviously during optimizing please replace the battery Please follow the steps below during optimizing 1 Disconnect the infusion pump the patients stop the infusion 2 Connect the infusion pump to the AC power charging continuously for 12 hours 3 Disconnect the infusion pump and the AC power using the battery as the power supply until the infusion pump powered off automatically 4 Connect the infusion pump to the AC power charging continuously for 12 hours 5 Optimizing battery performance is completed 2 4 3 2 Checking a Battery Regular check for the battery is needed due to the reason that the battery function will decrease during usage Please follow the steps below when c
20. e pressure calibrating data will be saved in system if No the system defaults the last calibrating data The coefficient ranges from 0 5 to 2 If the coefficient saved out of the range the system will automatically return to the Advanced Setting interface and default the former calibrating data e Itis necessary to calibrate the pressure when the material of infusion tube is too hard or soft To power off the infusion pump on the interface of pressure calibration is not allowed Make sure correct installation of infusion tube whose pinching part should be proper and no air bubble inside the infusion tube 5 7 NWARNING e The pressure calibration interface has no occlusion alarm Do not carry out the infusion operation in order to prevent any severe harm to patients 5 6 Changing Infusion Tube Brand The infusion tube IS G V3 1 of Dragon heart brand is the standard setting for this infusion pump If infusion tube of other brand be used by the user it is necessary to reset infusion tube parameters as the following steps Step 1 prepare a new brand of infusion tube Step 2 start the infusion pump and enter into the interface of setting menu Step 3 fix the infusion tube well according to the correct installation steps Step 4 Press the key and the key simultaneously on the mode setting interface to enter into the interface of Advanced Setting so as to set parameter for the infusion tube 5 6 1 Selection of IV Set B
21. ed NO 0 KVO Rate 1 0 ml h BOLUS 1000 ml Tube Mille Accuracy 30 Occ Val Mid Drop ML 20 AirLevel _ Level 2 Figure 5 9 There are 3 brands of infusion tube parameters that can be saved as the tube A B or C displayed on the top right corner of LCD stands for each band of the infusion tube being used Select infusion tube by pressing the key or in the Advanced Setting menu as shown in Figure 4 5 and make it adjustable by pressing the oro and cyclically choose A B or C by pressing the key or O and press the I3 again to save the setting 5 8 5 6 2 Setting Infusion Accuracy Bed NO 0 KVO Rate 1 0 ml h BOLUS 1000 ml Tube A Pipe 30 Occ Val Mid Drop ML 20 AirLevel Level 2 Figure 5 10 When there s comparatively large error occurred on the infusion accuracy or the currently used infusion tube needs to be replaced by any other brand it is necessary to adjust the accuracy of the infusion pump as the following steps Step 1 Start the infusion pump and then set flow rate and preset volume as 150ml h and 20ml h respectively Start infusion after the new brand infusion tube well installed and measure the liquid volume flowed from the new infusion tube with a graduated cylinder Step 2 If the volume of the liquid in the graduated cylinder more than the preset volume 20ml it needs to increase by 3 per 1ml to the former accuracy value If the volume less than the preset volume 20ml it i
22. ey A or to choose On or Off and finally the key to save it BedNO DropFUN OFF KVO Rate 1 0 ml h Locktime min BOLUS 1000 ml h KeySound OFF Tube A Pipe StartTip min Accuracy 30 Language English Occ Val Mid Default OFF Drop ML 20 AirLevel Level 2 Figure 5 13 Figure 5 14 5 7 2 Setting Drop Rate for infusion tube When different brands of infusion tubes to be used it is necessary to refer to the detailed parameters on the package of infusion tubes due to the drop rate parameters for the infusion tubes are quite different Select drop ml by pressing the key or on the first page of the Advanced Setting interface and make it adjustable by the key oK Input the relevant drop rate of the infusion tube and save it by pressing the key C NOTE e The setting range for infusion tube 1 100 5 8 Language Switching As shown in Figure 5 16 choose Language on the second page of the Advanced Setting mode and then select the language by pressing the key or O and finally save it through the o BedNO 0 KVO Rate 1 0 ml h BOLUS 1000 ml Tube A Pipe DropFUN OFF Locktime min KeySound OFF StartTip min Accuracy 30 Occ Val Mid Drop ML 20 AirLevel _ Level 2 Language English Default OFF Figure 5 15 Figure 5 16 FOR YOUR NOTES 6 Alarms 6 1 Overview Alarm is a warning indication given by infusion pump to alert medical care personnel through sound
23. g or similar devices otherwise electromagnetic interference may cause malfunction or breakdown Even the other devices comply with the emission requirements of CISPR they may also interfere with the infusion pump When the input signal amplitude is lower than the minimum amplitude in technical specifications it may lead to inaccurate measurements Portable and mobile RF communications equipment can affect the performance of monitor Electromagnetic Emission Guidance and Statement The infusion pump should be used under stipulated electromagnetic environment Customer or user should ensure using infusion pump under the following stipulated electromagnetic environment Emission Testing Electromagnetic Environment Guidance This infusion pump uses RF energy only when running its internal functions Therefore its RF l o emission is very low and will not produce any Radio frequency emission CISPR 11 nearby electronic equipment RF Emission Class B CISPR 11 Harmonic emission Class A IEC61000 3 2 Voltage fluctuation and flashing Applicable EC 61000 3 3 B 1 electromagnetic interference which affects the Guidance and Statement of Electromagnetic Immunity The infusion pump should be used under stipulated electromagnetic environment Customer or user shall ensure using infusion pump under the following stipulated electromagnetic environment l l Electromagnetic Immunity test IEC60601 test level Compliance
24. hecking battery function 1 Connect the pump to the AC power charging continuously for 8 to 14 hours 2 Disconnect the AC power supply and let the machine work on battery until it is turned off due to battery exhausting If the battery works for over 200 minutes the battery is in fine condition If the battery works for 60 to 200 minutes the battery is close to the end of its life If the battery works less than 60 minutes the battery needs to be replaced 3 Please charge the battery for future usage after checking 2 8 NOTE e If the using time of the battery is too short after full charge there might be a damage of the battery The power supply time of the battery depends on the using frequency of the pump and its setting parameters E g the display is in backlight mode e If the battery has obvious damage deformation bumps leakage or can not reach the capacity it should be replaced and recycled 2 4 4 Battery Recycling If the battery has obvious damage deformation bumps leakage or can not reach the capacity it should be replaced and recycled Please follow the applicable laws during recycle NWARNING e The battery must not be disassembled thrown into fire or short circuited The burning explosion and leakage of the battery may cause personal injury 2 0 FOR YOUR NOTES 2 10 3 Installation and Maintenance 3 1 Installation NWARNING e The software copyright of this infusion pump belongs to our
25. imum output power given by transmitter manufacturer The unit is watt Note 1 Use the higher frequency band formula between 80 M and 800 MHz Note 2 The above guidance does not apply to all cases because material structure objects and persons can absorb and reflect the electromagnetic wave and then affect the electromagnetic transmission C Alarm Information C 1 Alarm Information Note Column A means it can be totally eliminated Column B means it can be eliminated to acousto optic Column L means the alarm level Alam A B L Cause Solutions ores to stop alarm Air bubble in the remove the air bubble in infusion tube l l the set then press Air bubble Yes Yes High to restart infusion Infusion tube l l l l l Reinstall the infusion tube installation error Malfunction with the Contact manufacturer sensor Press key to stop l E infusion and stop alarm Preset infusion l volume have been Over Yes No High MN then press key to finished v eliminate the accumulated volume press key to restart infusion Press key to stop infusion and silence alarm Infusion tube occlusion then press gt key to restart infusion after Occlusion Yes No High moving the occlusion in the loop The occlusion value l Increase the cclusion level is much too sensitive Malfunction with the Contact manufacturer sensor Infusion Infusion set d Yes No Low l l Restall the infusion tube set installati
26. infusion to patients Any institutes or units such as hospital outpatient emergency rooms wards operation rooms observation rooms clinics nursing home etc capable enough to provide health care is expected to use this infusion pump N WARNING e Check the infusion pump and its accessories before use to ensure its normal and safe operation NCAUTION e The operation environment and power supply of this infusion pump must meet the requirments in A Product Specification 2 1 2 Contraindications None 2 1 3 Product Structure Composition and Performance iP 12B Infusion Pump consists of the shell pump device the board card and battery etc iP 12B Infusion Pump contains the following parts B Microcomputer System the core of the whole system which gives intellectualized control and management over the whole system and processes detection signals In this system two single chip Micyoco SCM systems are adopted for mutual backup copy and supervision When one SCM goes wrong the other one will give a timely warning signal and cut the power of the host 2 1 computer to stop the pump with the purpose to ensure the patient s safety Pump Device the power source of infusion employs step motor to drive the pump tablets continuously extruding upon infusion tube to materialize infusion Detection Device the device mainly includes all kinds of sensors like air bubble sensor detect air bubble inside the infusion tubes pre
27. latest setting NOTE Inthe body weight mode the infusion rate is calculated as the flow rate value by such parameters as kilogram and weight e The flow rate and the accumulated volume are not adjustable 4 4 4 2 4 Clearing Accumulated Volume Press the key to clear the accumulated volume when the machine is in stop condition NOTE e The accumulated volume can cleared only when the infusion pump is in stop status NOTE e The pump will stop working automatically once the serious low battery alarm sounds during the infusion 4 2 5 Starting Infusion After setting all the parameters and proper installation of the infusion tube press the key the motor begins to run and the pump starts infusing The indicator lamp is flashing when the machine is working NWARNING e The pressure calibration interface has no occlusion alarm Do not carry out the infusion operation in order to prevent any severe harm to patients 4 2 6 Infusion Completed When the preset volume reaches the volume limit the LCD will display OVER and sends an audio visual alarm to alert the user that the infusion is finished Press the key to stop the infusion 4 5 4 2 7 Shutdown Please take the following steps to turn off the infusion pump 1 Disconnect infusion tube between patient and the pump O 2 Press key and release the key when the backlight flicker seconds the power is turned off NOTE e The battery can not be recharged
28. level l l environment guidance Th Electrostatic discharge ESD IEC 61000 4 2 Electricity rapid pulse group EFT IEC 61000 4 4 Surge IEC 61000 4 5 Voltage drop short supply interruption and voltage change IEC 61000 4 11 Industrial frequency magnetic field 50Hz 60Hz IEC 61000 4 8 6 kV contact discharge 8 kV air discharge 2 kV power cord 1 kV I O cable 1 kV differential mode 2 kV common mode lt 5 Ur drop gt 95 Ur 0 5 cycle 40 Ur drop 60 Ur 5 cycle 70 Ur drop 30 Ur 25 cycle lt 5 Ur drop gt 95 Ur 5 seconds 6 kV contact discharge 8 kV air discharg 2 KV power cord 1 kV differential mode 2 kV common mode lt 5 Ur drop gt 95 Ur 0 5 cycle 40 Ur drop 60 Ur 5 cycle 70 Ur drop 30 Ur 25 cycle lt 5 Ur drop gt 95 Ur 5 seconds e ground must be woodiness concrete or tile If floor is with the humidity should be at least 30 ceramic covered synthetic materials relative Nets power quality must be a typical business or hospital environment Nets power quality must be a typical business or hospital environment If the infusion pump working during a break in the needs continuous nets power we recommend uninterrupted UPS power supply Not applicable Note Uy refers to the exchange net voltage before exerting test voltage B 2 Guidance and Statement of Electromagnetic Immunity The infusio
29. n of this pump may not meet its specifications Only standard components connectors and disposable products can be used with this pump Subsidiary items are not allowed to be attached to the pump and its accessories Reconstruction of the pumps is not allowed 1 2 The accuracy will not be maintained when the pump is used with the non standard infusion tube or the parameters of the infusion tube are not set accurately The maximum deviation may reach 40 or above Disposable accessories must be disposed after use in accordance with the relevant regulations of the hospital This infusion pump belongs to Class ll type of electric shock protection the supplied Type power cord PE earth terminal should not be used as ground protection and functional earthing Do not open the case of the infusion pump otherwise there might be electric shock The infusion pump must be maintained or updated by maintenance staff trained and authorized by our company Packing materials must be disposed in accordance with the relevant local statutes or the waste disposal regulations of the hospital They must be kept out of the reach of children The double thickness of the infusion tube should be between 0 8mm 1 2mm Outer diameter should be between 3 5mm 4 5mm Otherwise its accuracy can not be guaranteed which may cause severe injury to patients 1 3 1 1 3 Cautions NCAUTION Please use the accessories specified in this User s Manual to guran
30. n pump or its accessories by accident and make the infusion pump not work please contact with the agent or manufacturer The device should be cleaned regularly The cleaning frequentness should be improved in areas with serious environmental pollution or heavy wind and sand Please consult or refer to the specific regulations about device cleaning in the hospital The recommended cleansers are Warm water Diluted soap water Diluted aqua ammonia Sodium hypochlorite bleaching power for washing Hydrogen peroxide 3 Ethanol 70 Isopropanol 70 3 7 When cleaning the device 1 Turn off the power and disconnect the power cord 2 Wipe the case with soft cotton balls adsorbing the cleanser 3 Wipe the surface of the device with soft cloth adsorbing 75 of alcohol 4 Keep the device in the cool and ventilated environment to dry up The above steps are for reference only Disinfection effects should be checked with the correct method NCAUTION e Do not use gas EtO or formaldehyde for sterilization 3 2 3 Preventive Maintenance 1 Check the Infusion Rate Using measuring cylinder and stopwatch to check the infusion volume for every 6 month 2 Maintain the Battery Performance Please refer to 2 4 3 Battery Maintenance Regular Maintenance Routine Maintenance Procedures According to the Thoroughly clean the feeding pump shell before or after long hospital policy period of storage 1 Check the AC power pl
31. n pump should be used under stipulated electromagnetic environment Customer or user shall ensure using infusion pump under the following stipulated electromagnetic environment l IEC 60601 Test Compliance l Immunity Test Electromagnetic Environment guidance Level Level Conduction Portable and mobile RF communications 3 Vrms 150k 80MHz IEC61000 4 6 equipment and or systems including cable immunity equipment must be used outside the of any parts the prescribed distance The separation distance is based on the transmitter frequency to choose the right formula calculated The suggested calculation formula of isolation distance is d 9 2 d 1 2VP 80M 800MHz mM d 2 34P 800M 2 5GHz Radiation 3V m immunity 80M 2 5GHz 3V m Among them P is the Nominal maximum IEC61000 4 3 output power of transmitters its unit is watt d is the recommended distance its unit is meter The field strength of RF transmitter obtained in electromagnetic field measurements a in every frequency range b must be less than line level It may appear interference by the equipment marked the following sign e A Note 1 Use higher frequency band formula between 80 MHz and 800 MHz Note 2 The above guidance does not apply to all cases because material structure objects and persons can absorb and reflect the electromagnetic wave and then affect the electromagnetic transmission The field strength of Radio honeycomb and wireless mobile
32. n uc C 1 C2 Prompt MES teo ess C 4 D Symbols and Terminology iron re ena cebat pue tecto oo en Ex ou cena eie poBeer UE D 1 BESIDE D 1 D 2 TENO OOV v A D 2 FOR YOUR NOTES 1 Safety 1 1 Safety Information The safety statements presented in this chapter refer to the basic safety information that the operator shall pay attention to and abide by There are additional safety statements in other chapters or sections which may be the same as or similar to the followings or specific to the operations N DANGER e Indicates an imminent hazard that if not avoided will result in death or serious injury N WARNING e Indicates a potential hazard or unsafe practice that if not avoided could result in death or serious injury N CAUTION e Indicates a potential hazard or unsafe practice that if not avoided could result in minor personal injury or product property damage NOTE Provides application tips or other useful information to ensure that you get the most from your product 1 1 1 Dangers There are no dangers that refer to the product in general Specific Danger statements may be given in the respective sections of this manual 1 1 1 1 2 Warnings NWARNING This infusion pump is used for clinic infusion and it can only be used by professional clinicians medical electrical experts or well trained nurses on specific occasions Infusion pump and its accessories must be inspected before use to guara
33. ntee its normal and safe operation Avoid using this infusion pump in the flammable or explosive atmosphere in case of fire outbreak or explosion Infusion alarms must be set based on the actual situation of the patients Do not rely too much on the audible alarm system in the infusion supervision Pay close attention to the actual clinical situation of the patient Keep observing the remained liquid volum in infusion bags or infusion bottles and check if there is any air bobble in infusion tubes during the infusion Do not rely on the alarm function of the infusion pump only The pressure detector may not work normally in high pressure environment especially in hyperbaric oxygen therapy Making sure the blood vessel is well protected before infusion In the infusion tube the occlusion caused by tube knot and murphy s dropper coagulation or intubations may lead to the rise of the inner pressure of the infusion tube At this moment the effort to eliminate the occlusion may cause too much liquid to be infused into the patient s body with a large dose Proper measures should be taken to prevent this phenomenon For example to clamp the infusion tube before occlusion elimination This infusion pump should be used 120 CM above or below the patient s heart Avoid using the infusion pump when there is any alarm When another set of infusion system or accessories is connected to the infusion tube used in this infusion pump the operatio
34. on error C 1 installation Malfunction with the Contact manufacturer error sensor Abnormal l Data communication Contact manufacturer Yes No Medium control 1 error Press key to stop infusion and eliminate the Abnormal Something wron Yes No High l z 3 alarm Then press SS control 2 with step motor l l m key to restart infusion if it happens again please contact manufacturer to repair Drop rate High The drop rate Set the correct drop rate error drop parameters are parameters sensor is improperly set required The ua is not Calibrate the Aue of There is droplet on Shake off the droplet on the funnel tube wall the tube wall after operation for a long time which affects the detection of the drop rate sensor The infusion Eliminate the occlusion in pipeline is not the infusion loop smooth The Jia rate Contact manufacturer sensor is faulty pu ee NoAC Low No AC power Connect the AC power Power supply cord Low No No High Low battery volume Connect to AC power to Battery aging or Contact manufacturer infusion pump charge circuit fault Battery No No High Low battery volume Connect to AC power to Exhausted charge the battery Battery aging or Contact manufacturer to infusion pump repair charge circuit fault C 2 Alam A B L Cause Solutions Start No No Low After correct prompt installation of infusion tube the infusions pump does n
35. onding to the clamp and then twist the clamp knob clockwise till the infusion pump installed well on the stand NOTE e The infusion pump must be put horizontally e Please make sure the stability of stand before installation 3 1 5 Install Power Cord Plug the power cord into the AC power cord inlet NOTE e Applicable power supply scope is 100 240V 50 60HZ e A C power cord should be inserted properly and tightly 3 1 6 Installation of Drop Sensor Optional NOTE e This section has to be used with the optional Drop Sensor The user may skim over the instruction in the section if Drop Sensor is not equipped with the infusion pump e The Drop Rate function can be started only when the rates400ml h 3 4 Figure 3 4 Figure 3 5 1 Firmly insert the power cord of Drop Sensor to the connecting port on the rear panel and make sure the volume of the liquid to be filtered less than 1 3 that of the liquid filter at meantime 2 As shown in Figure 3 5 the Drop Sensor to be clipped to the liquid filter the direction of pressure by hand as shown in Figure 3 4 must be over the liquid interface NOTE e The liquid interface in the filter must be lower than the Drop Sensor e The positioning block of the filter must be vertically inserted through the positioning groove of the Drop Sensor e The infusion tube pipe must be changed by a new one after continuously working over 24 hours e Do not incline the drop rate
36. ot start in the set time Door lock Yes Yes High In the process of Open infusion open door lock C 3 Start infusion after the right installation infusion tube Set start notice refers to 5 1 4 Advanced Setting Press key to stop infusion and eliminate the alarm put down the door lock and then press the key to restart C 2 Prompt Message None C 4 D Symbols and Terminology D 1 Units E D 2 Terminology NN 750 055 lamp emitting diode po mme A read only memory D 2 Ziocare p F x Ziocare Shenzhen Biocare Bio Suddical Eguimmeni Gm ktg Hibin Fuacierg LY Ha Fa Tai p TZ D E7560866 Fam mI Eb il TLTTIM i LI quist DTI Nu EE
37. ountermeasures NWARNING e Please check the condition of the patients when an alarm occurs In case of the infusion pump alarms take the following steps Check the condition of the patient Confirm the parameters and alarm type Identify the cause of alarm Solve the cause of alarms Qu dm Do Du um Confirm if the alarm has been eliminated NOTE e Regarding detailed counter measures to each alarm please refer to Appedix C Alarm Information 6 2 A Product Specification A 1 Safety Specification Parameter Standard SFDA Classification Class II Type of Shock Protection Class II including inner power supply device Degree of Shock Protection Type BF except quiver discharge effect application part Classification of Waterproof IPX1 Operating Mode Continuous operation Degree of Mobility Portable device A 2 Environmental Specification Operating Temperature 5 C 40 C Operating Humidity 20 80 non condensing Operating Atmospheric Pressure 86kPa 106kPa Storage and Transportation 20 C 50 C Temperature Storage and Transportation Humidity 10 95 non condensing Storage and Transportation i 50kPa 106kPa Atmospheric Pressure Storage Condition Statement Storage Condition Statement Statement Norecorrosive gases and well ventilated room corrosive Norecorrosive gases and well ventilated room and well ventilated room A 3 Power Supply Specification Input Vol
38. ow Notes for parameters 0 1 1 0 ml h Infusion pump starts KVO function and runs at the KVO rate after KVO Rate Occlusion stops Note The KVO function is able to start only when the current rate more than the set KVO rate BOLUS The Bolus flow rate is adjustable with the range of 100 0 1000 0 ml h and the default value of 1000 0 ml h inspection 30 108 It is used for calibrating infusion tube There are three occlusion levels namely the low level the medium level and Oe val the high level which are corresponding to the pressure values of 60 kPa 100 m kPa and 140 kPa respectively with a volatility of 20 kPa and the default level is Low Tube A tube B tube C users can customize the brand To prevent confusion to Tube use the brand recorded the A B and C represent the infusion tube brand for 5 4 Drop ML The parameter for Infusion set specification namely the drop number in 1ml liquid For detailed value the user can refer to the package of each infusion tube The range is from 10 to 100 drop ml and the default value 20 of drop ml Air Bubble Filter lt is used for setting the level of sensitivity of tiny bubble Air Level alarms There re four levels Off 1 3 the higher the filter stalls the greater the capacity of filtered bubbles are Drip FUN The start up and shut down are available When the infusion pump stops the j detection of the drip rate will stop Off 1 6 minutes and the default
39. r supply make sure the voltage and frequency of the power supply meet the label of the pump or the specific requirments in this User s Manual Please install and carry the infusion pump appropriately to protect the pump from drop impact strong oscillation or other damage caused by machinery external force Use a piece of wet soft cloth with warm water to wipe the surface of the infusion pump when there is any liquid on 1 4 If the surface tention proportion and viscosity of the infusion solution is different from saline for example a kind of solution mixed with surface activite agent the infusion accuracy may be different from the accuracy listed in the specifications table When the infusion rate is high 2 1000ml h high quality silicone tubes with 0 9mm transfusion needles must be used with the pump to keep the infusion accuracy If the infusion pump fails to work as specified in the User s Manual due to any uncertainty please stop infusion and report the situation including infusion accessories used with the pump infusion volume infusion rate SN liquid type etc to your supplier or our company The drop sensor is not applicable for light proof medicine infusion Adopting light proof IV sets on the pumps might cause failure operating of drop sensor and sever damage to the patients 1 1 4 Notes NOTES Please keep this User s Manual along with the infusion pump for the convenient and timely reference Plea
40. ress the key to return to the setting interface and silence the alarm sound If infusion needs to continue then press the NS to clear the accumulated volume NOTE e The preset volume can not be set in the Time Mode 5 1 3 Setting Other Parameters After setting rate press the key Or to select other parameter and set their value For the detailed parameters please refer to Table 1 NOTE e When setting decimal fraction available press the key to select the right corner value as 0 1 and then the key to add or the key to subtract e The right corner value is free of affection by pressing or Y when selecting other parameters e Accumulated volume gt namely the infusion volume accumulated during infusion is unable to set In stop status to press the key Is to clear the accumulated volume 5 3 5 2 Advanced Setting In stop status press the key and the NO simultaneously on the mode setting interface to enter into the interface of Advanced Setting as shown in Figures 5 4 page 1 and Figures 5 5 page 2 After parameter setting press the key and the key together again to return BedNO OQ DropFUN OFF KVO Rate 1 0 ml h Locktime min BOLUS 1000mI KeySound OFF Tube A Pipe StartTip min Accuracy 30 Language English Occ Val Mid Default OFF Drop ML 20 AirLevel Level 2 Figure 5 4 Figure 5 5 The parameters can be set in the user interface are shown in the table bel
41. s necessary to decrease by 3 per 1ml from the accuracy value If the volume same with the preset volume 20ml it is needless to adjust the accuracy value When adjusting accuracy enter into the interface of Advanced Setting by pressing the MS and the C simultaneously on mode setting interface and then select Accuracy by pressing the NOS Or O and make it adjustable by pressing the Moro as the Figure 5 10 shows adjust the accuracy value by pressing the NOS Or and finally save the value by pressing the oro Example 1 If the volume in the graduated cylinder and the former accuracy value is 21ml and 50 respectively the accuracy value should be adjusted to 53 Example 2 If the volume in the graduated cylinder and the former accuracy value is 19ml and 50 respectively the accuracy value should be adjusted to 47 5 9 Step 3 Repeat the step 1 and step 2 till the accuracy value be precise the volume in the graduated cylinder and the preset volume are the same NOTE e Infusion accuracy 15 e In order to reduce the measuring error the infusion tube needs to be filled with liquid without any air bubble inside before measuring accuracy The accuracy value has to be set again when changing brand of infusion tube 5 6 3 Setting Occlusion Level Adv Set 100 BedNO 0 KVO Rate 1 0 ml h BOLUS 1000 ml Tube A Pipe Accuracy 30 Mid Drop ML 20 AirLevel Level 2 Figure 5 11 Select Occlusion Level
42. s on the screen release the key to restore the original flow rate NOTE e Bolus function should be started under normal infusion e Any alarm function will not be affected by Bolus function e If flow rate gt Bolus rate 100 1000ml h the Bolus rate can not be started when pressing the me e The flow volume of Bolus infusion is accounted into the accumulated volume e When rate gt 400ml h the Drop dection will automatically be off 5 5 Pressure Sensor Calibration Simultaneously press the key and the key under the Advanced Setting mode to enter into the interface of pressure sensor calibration as shown in Figure 4 10 the following steps to be taken 5 6 1 Connect infusion tube and pressure gauge to the infusion pump 2 Setflow rate 100ml h is to be recommended when setting rate the max rate can be used if the pressure gauge employed to the sensor calibration 3 Start infusion by pressing the key until the pointer of pressure gauge exceeds 100kpa press the key till the pressure down to 100kPa the pressure can also be set as the same with the pressure gauge and then press the key EY 4 Keep pressing the key to exit and choose to or not to save the calibrating result pressing the key or to select Yes or No and the key to save To Save Your Data Rate 100 ml h Pressure 100 0kPa Pressure 54 Initial 0 Yes Factor 0 63 No Figure 5 7 Figure 5 8 NOTE e If Yes is chosen th
43. se install the infusion pump to the place convenient for observation operation and maintenance This User s Manual describes all the configuration and functions of the infusion pump The infusion pump you bought may not have some of the configuration or functions Please do not insert devices which are not specified by our company to the data interface The SN of this infusion pump has been set Users are not allowed to change it 1 5 1 2 Equipment Symbols Note Please refer to l ass Class II Equipment ur Prevented against drippin Type BF applied parts IPX1 9 pping D water Alternating Current Direct Current Power Supply Power Supply AC DC Batch No Serial No Date of Production Manufacturer Pollution Free Wireless transceiver Treatment Upward or Add Value Downward or Reduce Value Turn on Turn off Fragile items handle l Transport package fear of rain o lt lt EB with care The same packing stacked up to 5 layers rao I B B Transport should be straight up m 8 Authorised Representative in the European Community The CE mark is a protected conformity mark of European Community The products herewith comply with the requirements of the Medical Device Directive 93 42 EEC CN TA 0123 1 6 2 The Basics 2 1 Product Introduction 2 1 1 Application Scope This infusion pump is used in wards operation rooms and observation rooms for accurate and continuous
44. set is Off The keys are locked when the time of no key operation exceeding the set key lock time If the user needs to make Lock Time the keys operable it is necessary to press the two keys and together to unlock Key Sound On Off Used to turn on and turn off the key sound Off 1 6 minutes and the default set is Off When pressing the o key can Start Tip immediately start the infusion if no operation or alarm occurs in a set period of time the no operating alarm will be triggered to prompt the user to start the infusion pump MA P x English Spanish Francais u NOTE e Drop rate function is optional and can be started only when Drop Sensor is installed with infusion pump 5 3 Unlocking This infusion pump has key lock function The key lock time can be set by the user on the Advanced Setting interface as shown in Figure 5 6 The keys are locked when the time of no key operation exceeding the set key lock time If the user needs to make the keys operable it is necessary to press the two er A and simultaneously to unlock 5 5 DropFUN OFF Locktime min KeySound OFF StartTip min Language English Default OFF Figure 5 6 9 4 Starting Bolus Function Bolus In the course of infusion if it needs to speed the infusion rate and when the current rate less than BOLUS rate 100 1000ml h press the key tightly and the infusion pump is running at the BOLUS rate which display
45. set parameter See Chapter 5 Function and Interface Press the key to infusion firstly and then the key after air bubble eliminated from infusion tube Press the key gt gt gt 4 2 Operation Steps NOTE e Part of this section covers the function of Drop Sensor If the user needs to use this function it is necessary to choose Drop Sensor as accessory to the infusion pump For more details please consult the distributor that sells the product to you or the manufacturer 4 2 1 Start Infusion Pump After fixing the pump please take the following steps to turn on the machine 1 Please refer to 3 2 1 Inspection to make safety inspection before turn on the pump O 2 Press the key The pump will start self checking LCD will display the software version and the machine will play the start up music of di 3 The infusion pump starts self checking 4 After a few seconds the pump will finish the self checking and enter the rate mode interface 5 Now user can operate the pump by keypad and panel NOTE e Symbol of power plug displayed on LCD means that the pump is supplied by A C power Press the key to open or close backlight of LCD when the pump is turned on e The battery can be recharged only when the machine is connected to AC power and the machine is turned on 4 2 4 2 2 Install the Infusion Tube 1 Pull out the door lock as the 2 Pull straight the infusion tube arrowhead s
46. ssure sensor detect the pressure inside the infusion tube etc Alarm Device the device mainly includes audible alarms and information alarms drawing the user s attention to the correct operation Input and Display Device the input device is in charge of setting infusion parameters such as flow rate etc And the display device is in charge of displaying all the parameters and the current working status on the screen Built in Battery the battery sustains the operation of the infusion pump when there is no AC power supply The performance of iP 12B Infusion Pump Accurate control of flow rate Accurate control of infusion volume Accurate control of infusion time Timely alarms for air bubble infusion Over occlusion low battery infusion tube installation error and control abnormal etc Provide multi infusion modes drop sensor mode optional rate mode time mode body weight mode 2 2 2 2 Appearance 2 2 1 Front Panel SY C2 NO Oe on gt A OO M e e M Rate 500 ml h PreS 0 0 ml lt moy pinbri AS PP A remi LI ilr TAL eee re 12B INFUSION PUMP AC lamp While the pump is turned off and the lamp is on it indicates AC power supply Running indicator lamp The lamp is on and flashes during infusion when the infusion tube is properly installed Pressure diagram To reflect the current inside pressure of the infusion tube
47. t 1000ml h when flow rate lt 1000ml h After removing your finger from the key it will return to its original infusion rate STOP ELIMINATE Alarm key In running status press this key to stop infusion When the alarm is on press this key to eliminate the alarm except for low battery alarm In value inputting status press this key to resume the original value and quit POWER key Turn on the machine Press this key for more than 2 seconds Turn off the machine Press this key for more than 4 seconds SELECT Key When setting the value by or key press this key to select the incremental value 0 1 1 10 100 1000 Some parameters setting can only select incremental value 1 10 100 1000 2 4 2 2 2 Back Panel 2 Eu Iw i Power tab Power socket Drop sensor socket drop sensor is an optional accessory Fixing Clamp Product label bea GA 2 3 Screen Displaying This pump is equipped with LCD screen The displayed information contains four major parts RateMode Rate 500 mi h Pres 100 mi J EN gt 0 0 mi 3 1 Title Bar To display current functional modes incremental value and type of infusion tube 2 Information Zone To display various parameters of current infusion mode 3 Status Bar To display infusion pump alarm information pressure status power supply and infusion status 2 4 Battery 2 4 1 Overview The infusion pump uses built in rechargeable battery to guarantee
48. tage 100V 240V Max Power Consumption 25VA running no less than 2 hours at the rate of 25ml h and operating Time after being fully recharged The battery shall charge automatically when the pump is Charging Time connected to the AC power and in power on situation It takes 8 14 hours for the battery to get fully charged A 4 Hardware Specification Parameter Standard Complete Appliance Size 140 mmx150 mmx220mm LengthxWidthx Height Weight 1 8kg LCD Liquid Crystal Display Type color LCD Size 3 0 inches Meo A 2 A 5 Basic Parameters of Infusion Pump Standard Requirement for Comply with GB 8368 2005 Standard for Disposable Infusion Tube Infusion Set with Gravity Infusion style Infusion pump Mechanism Peristaltic Mechanism Flow rate range 0 1ml h 2000 ml h Drop mode Rate mode time mode body weight mode Drop rate settable Drop rate 1 drop min 666 drop min Rate mode settable Rate Oml h 2000 ml h l Time 1min 6000 min Time mode settable Uso Te god d Weight 0 1 kg 300 0 kg Drug 0 1mg 999 9 mg Volume 0 1ml 999 9 ml Dose Depend on weight drug volume and dose unit Body weight mode settable Unit mg kg h ug kg min Selectable 1ml h 5 0ml h After occlusion alarms it will KVO rate start KVO P t vol reset volume TENET range VTBI Preset time range 0 6000 min Accumulated 0ml 9999 ml Infusion Volume Display Displayed
49. tee the safety of the patient Cables must be connected carefully to reduce the possibility of the patient getting intertwined or choked Disposable accessories can only be used once Reuse may lead to declined performance or cross infection When installation of the infusion tube is completed please observe whether there is leakage before the infusion If any leakage the machine should be examined and processed immediately Replace the fixing place of the infusion tube every 4 hours after starting infusion to guarantee the accuracy Replace the infusion tube after the infusion lasting for 24 hours This infusion pump or its accessories must be disposed in accordance with local statutes or hospital regulations after its operating life Please contact the distributor that sells the product to you or the manufacturer if there is any inquiry Electromagnetic field may influence the performance of the infusion pump Therefore equipments or devices used near the infusion pump must meet the EMC standard Mobile phones X ray or MRI equipments are all potential interference sources because of their high intensive electromagnetic radiation Avoid the direct sunshine high temperature or humidity Avoid exposing this infusion pump to high pressure sterilization or chemical materials Check the built in battery before use to make sure the power is enough Recharge the battery if necessory Before the infusion pump is connected to the powe
50. the line of information e The Drop Sensor is only acting as part of detection for infusion flow rate and can not be used to analyze and judge leakage 5 1 1 Setting Flow Rate Infusion pump defaults into rate mode once it is started The Rate is able to adjust by pressing the key e The value on right corner of LCD is about to cyclically change to 0 1 1 10 100 and 1000 by pressing the key time and time again till it is right value Then by pressing the key Or to add the right value to or subtract it from the Rate respectively by doing this again and again the user is able to set the value needed and finally save it by pressing the Nor For example if the user needs to set the rate as 1250ml h from the current rate 100ml h displayed on the screen take the following steps First press the key to switch the right corner value to 1000 and then the key once to make rate change into 1100ml h Second do the same as above to switch the right corner value to 100 and change rate into 1200ml h Third press the key to switch the right corner value to 10 and then the key 5 times to make the rate change to 1250ml h 5 2 If there s decimal fraction it only needs to select 0 1 for the right corner value by pressing the key and then add or subtract by the key or amp 5 1 2 Setting Preset Volume If preset volume is not zero infusion pauses with alarm for OVER when the accumulated volume equals to the preset volume p
51. ual describes the product s application function and operation in details Please read this User s Manual carefully and understand the content before use to ensure the proper usage and guarantee the safety of the patient and the user This User s Manual describes the product as per the most complete configuration Some content of this manual may not be applicable for the product on your hand Please contact us for any questions Please keep this User s Manual beside the infusion pump in order to consult it conveniently Intended Audience This User s Manual is only applicable for well trained clinical people Illustrations All illustrations in this User s Manual are used for reference only lts settings or data may be not entirely consistent with the actual displayed info on the product Conventions B Italic text is used in this manual to quote the referenced chapters or sections B The terms danger warning and caution are used throughout this manual to point out hazards and to designate a degree or level of severity VI Contents Mi NY ee ee RP NE EUR 1 1 AS A mr 1 1 el Dane Sidonia 1 1 A A 1 2 A een ee a 1 4 Es mper A re MI 1 5 1 2 EQUIPMEeNt Symbol pia Ai 1 6 LINDAS reta 2 1 2 d TOGHCETIDUOGOUCIIOD Erika 2 1 2 1 1 Application SCODE rca 2 1 212 CON alt CCA ONS an d aset iia 2 1 2 1 3 Product Structure Composition and Performance 2 1 PAPAA i uM an eade tua mI EIE uer E Eu E 2 3 2
52. ug and power cord 2 Run the machine until it gives a low battery alarm Then Check to the pump charge the battery to ensure it works and recharge well 3 Check if the machine leakage after correct installation of IV set at least once a year 3 2 4 Pollution Free Treatment and Recycling The service life of this product is 3 years The pump exceeding its service life should be discarded Please contact the manufacturer or distributor for more relevant information You can make the following treatments 1 iP 12B infusion pump that has been scrapped could be sent back to its distributors or manufacturer for proper recycling 2 Used up lithium polymer batteries could be delivered to its distributor or manufacturer for disposition or treated according to corresponding regulations 3 8 4 Operation Guide 4 1 Operation Flow Chart Fix the infusion pump Start the infusion pump Install infusion tube Set infusion parameter Eliminate air bubble from tube Clear accumulated volume Insert infusion accessories into Connect infusion accessories to patient patient Press the key Infusion completed i Shut down the infusion pump Press the key wy l Fix the infusion pump on the stable infusion tube stand Press the key Fix the infusion tube to the groove bottom of the gt pump straightly and check if there is any leakage after well installation of the infusion tube Press the key to
53. ust or corrosive inflammable or explosive Substances There should be 2 inch 5cm interspace around the infusion pump to make sure the air moves freely When the infusion pump is transferred from one place to another the difference in temperature and humidity may cause condensation to the infusion pump In this case please do not turn on the pump until there is no condensation 3 1 3 Power Supply Requirements The power supply of this infusion pump must meet the requirements in A 3 Product Specifications NWARNING e Make sure the working environment and power supply meet the environmental requirement and the power supply requirement listed above Otherwise the infusion pump will not meet the technical specifications claimed in A Product Specifications and it may also cause the unexpected consequence such as device damage e The power supply must be selected in accordance with the settings of the system power voltage Otherwise it may cause sever damage to the system 3 2 3 1 4 Fix Infusion Pump Figure 3 1 Direction for fixing infusion pump as shown in Figure 3 1 1 Steel tube of infusion pump stand 2 Screw of clamp Figure 3 2 Figure 3 3 3 3 Steps to install infusion pump to infusion pump stand As shown in Figure 3 2 for convenience counter clockwise twist the clamp knob and make enough room for the installation of the pump on the stand As shown in Figure 3 3 place the stand at a position corresp
54. when the machine is turned off e Rate and the other parameters shall return to default values after machine is turned off 4 6 5 Function and Interface 5 1 Infusion Mode and Parameter Setting Infusion pump defaults into rate mode once it is started To use other infusion modes press the NO As shown in Figures 5 1 5 2 and 5 3 the setting interfaces of rate mode time mode and body weight mode will be displayed successively by pressing the NO RateMode 100 A Rate 1 0 ml h PreS 0 0 ml X 1 0 0 ml TimeMode z100 A BW Mode 100 A _ Vol Rate 1 0 ml h E o 0 0 ml Figure 5 1 Figure 5 2 Figure 5 3 On the setting interface of rate mode press the keys and to switch to Drop rate mode and then repeat to return to rate mode umm 666 drops minute the range is subject to the parameter drop ml Drop Rate 0 1 2000 0mih Rate Mode Time Mode 0 1 9999 9m Table 1 5 1 NWARNING e Please not to start Drop rate to infuse liquid if no Drop Sensor is installed with the infusion pump NOTE e Parameters to be set vary from the infusion modes selected For details please refer to Table 1 e The unit value used in infusion will be automatically saved when the infusion pump off e If the Drop rate is started with no Drop Sensor installed the infusion running under any of modes by the user won t stop immediately though Drop Rate error alarm will be displayed in
Download Pdf Manuals
Related Search