R&S®SMU200A Release Note Version 2.20
Contents
1. Max value of dwell time increased The mode STEP now can be remote controlled e SOURce LIST INDex lt nr gt addresses the specified index e SOURce LIST TRIGger EXEC executes a single list step e Accelerated operation of LTE and Wimax e Frequency Offset has been extended to 67 GHz e Factory preset resets computer name e Suppression of test signal when performing local I Q modulator adjustment CAL IQM LOC e Phase offset extension of range 999 99 deg to 999 99 deg e Adjustment uses external reference if activated e List mode dwell time extended to 100 s e User correction warning when leaving frequency limits e Instrument can be shut down remotely using SYSTem SHUTdown e Booting speeded up by typ 20s e New filter Lowpass EVM optimized useful for WLAN and other OFDM standards Fixed Issues Possible hangup after fast changing digital standards remotely fixed 7681 GSM some parameters missing after recalling a setup fixed 7520 SRQ handling over VXI11 delayed by 200 ms fixed 7423 Signal of Marker 4 output at User connector corrupt fixed 7566 List mode sporadic errors when switching between several lists very fast fixed 7550 List mode Reset did not work with mode step fixed 7468 Fading Sour fsim path lt nr gt commands did not all work properly fixed 7463 Fading Fading Mimo Correlation Matrix not completely saved modes 4x2 and 2x4 fixed 7455 Fading SOURce lt 1 2 gt PRESet2. SMU with BBOUT SMU K18 but without BBIN SMU K17 some problems with ExBox fixed Sporadic bit errors in GSM and 3GPP FDD signal generation problem was observed only in combination with UNICOD version gt 6 00 fixed 1 19 Version 2 04 303 31 Released Feb 2008 New Functionality e SMU K65 Assisted GPS Fixed Issues Sporadic extension of setting times for level and frequency fixed 6273 Wrong display of AWGN values in display mode baseband fixed 6290 1 20 Version 2 04 303 17 Released Nov 2007 Fixed Issues Option SMU B30 B32 B35 B37 should not be displayed with new CMOS attenuator 6195 Support of multilevel user correction protected with a registry key feature now available for all 6196 AM Sometimes an error message output unlevelled occurred when using AM with low deviation 6206 1 21 Version 2 04 303 16 Released Oct 2007 New Functionality e SMU B18 baseband digital out board e SMU K47 1xEVDO Rev A Release Notes for Firmware 1008 0329 52 23 R amp S SMU200A Information on the Current Version and History e SMU K53 T DMB DAB Modified Functionality e Support of BB Input mode Digital Input with BBINS Rev 5 01 and BBINR Rev 3 00 or higher e Support of R amp S EX IQ Box 1409 5505 02 Fixed Issues XM Radio No markers in physical layer mode Terrestrial A and Terrestrial B 5834 IEEE 802 16 WiMAX system crash possible when changing from uplink to downlink
3. Release Notes for Firmware 1008 0329 52 24 R amp S SMU200A Information on the Current Version and History mode Armed Auto external W3GPP copy BS1 to BS2 doesn t copy all relevant parameters 5802 WLAN when setting state to ON the filter settings are always the default one not the displayed one 5816 AWGN Doesn t work if no option B9 10 11 or B17 is installed bug in V2 04 202 only 5833 GSM Recall doesn t set the frames 5882 WLAN sequence length not limited correctly 5894 Fading system crash when copying a path group to an other one 5905 CDMA2000 unknown exception when using predefined settings RC4 with frame length 80 ms 5930 WiMAX e Corrigendum2 D4 compatibility e Uplink Sounding e Added Zone_Switch_IE in DL MAP e Mixed STC Matrix A and B configuration within the same zone e CID_Switch_lE inclusion in DL MAP can be toggled e Added Collaborative Spacial Multiplexing in uplink e Fading ITU profiles now available without option SMU K72 1 23 Version 2 04 202 Released March 2007 Fixed Issues e Sometimes at startup an error message occures unicod SDRAM only with V2 04 201 e BBIN in rare cases the output spectrum is not ok only with V2 04 201 e Fading predefined WIMAX settings parameter Virtual RF not considered 1 24 Version 2 04 201 Released March 2007 New Functionality e SMU K55 EUTRA LTE e SMU K56 XM Radio e SMU K72 new fading profiles for WiMAX Gauss e S
4. e Custom digital modulation display type of modulation directly in the baseband block Modified Functionality e Custom digital modulation Modulation Type Variable FSK 4 8 16FSK with free selectable deviations available now e Custom digital modulation display type of modulation directly in the baseband block e User Marker Aux I O Settings now directly in menu Trigger Marker e separate rst for path A and B possible via SOURce lt HW gt PRESet and DEVice PRESet Release Notes for Firmware 1008 0329 52 32 R amp S SMU200A Information on the Current Version and History e Digital standard 3GPP FDD Channel Coding Transport Channel max value of Transport Blocks now 24 e GSM EDGE External Clock trigger delay and trigger inhibit available Fixed Issues e Q impairments user settings lost when switching baseband state to off and on again fixed e SCPI order freq min max and pow min max does not work fixed e Editing a bit pattern in very rare cases the system crashes while editing the pattern fixed e In some cases the tooltip lost the units fixed e File dialog sometimes two lines are highlighted and or no focus fixed e Digital standard 3GPP FDD sometimes no marker output at first start fixed e Digital standard 3GPP FDD unnecessary info messages when selecting Set To Default or Recall 3GPP FDD Settings fixed e Custom digital modulation error message us
5. B35 B37 e Support of BER BLER measurement Option SMU K80 Modified Functionality e Several additional improvements in 3GPP e Several improvements in GSM EDGE Fixed Issues e Analog Modulation Internal modulation generator Output voltage setting accuracy for V lt 300mV fixed e Overvoltage Protection now is indicated in display and via SCPI status reporting e Several problems in GSM EDGE fixed e Several problems in 3GPP fixed ee ee Release Notes for Firmware 1008 0329 52 37 R amp S SMU200A Information on the Current Version and History e Several problems regarding Phase Setting fixed e Blank signal only worked with active digital modulation This is fixed e System stopped when running Sweep for a long time with short dwell times This is fixed 1 48 Version 1 04 14 Released March 2004 New Functionality e Support of 6GHz extension 1 49 Version 1 04 13 Released Jan 2004 Modified Functionality e On firmware installation option SMU Instrument Setup is the default instead of PC Simulation Setup Fixed Issues e Devices equipped with two baseband pathes and one RF path Several problems regarding this configuration are fixed 1 50 Version 1 04 11 Released Nov 2003 New Functionality e Support for option AWGN Option R amp S SMU K62 Add White Gaussian Noise Modified Functionality e Significantly improved performance of the user interface e Significantly improved disp
6. Tel from USA From outside USA Fax E mail East Asia Monday to Friday 8 30 AM 6 00 PM Tel Fax E mail Rest of the World Monday to Friday 08 00 17 00 Tel from Europe From outside Europe Fax E mail except US public holidays Eastern Standard Time EST 888 test rsa 888 837 8772 opt 2 1 410 910 7800 opt 2 1 410 910 7801 CustomerSupport rohde schwarz com except Singaporean public holidays Singapore Time SGT 65 6 513 0488 65 6 846 1090 CustomerSupport rohde schwarz com except German public holidays Central European Time CET 49 0 180 512 42 42 49 89 4129 13776 49 0 89 41 29 637 78 CustomerSupport rohde schwarz com 0 14 Min within the German fixed line telephone network varying prices for the mobile telephone network and in different countries Release Notes for Firmware 1008 0329 52 46
7. is now also available with SCPI triggering e New command SOURcef 1 2 SWEep FREQuency RUNNing to poll sweep state e 1xEVDO SMx K47 Forward Downlink is now generated in realtime with immediate signal update and uninterrupted output at parameter changes Fixed Issues WiMax Restore settings from a two channel device to a one channel device causes a crash if coupled mode was switched on fixed 7328 Marker signals are delayed to the IQ signals only V2 05 222 24 affected fixed 7373 Menu SETUP entry Reference oscillator missing only V2 05 222 24 affected fixed 7389 Fading correlation is lost when changing speed parameter fixed 7401 RF output with all IQ modulations level is up to 6 dB too low only V2 05 222 24 affected fixed 7402 EUTRA LTE Release Notes for Firmware 1008 0329 52 16 R amp S SMU200A Information on the Current Version and History Compatibility e All supported features are in line with the following official 3GPP specifications o 1836 211 v 8 3 0 o 1836 212 v 8 3 0 o TS36 213 v 8 3 0 e This version of the SMx K55 is compatible with R amp S FSV K100 K101 K102 and R amp S FSQ K100 K101 K102 K104 K105 EUTRA PC Software General Features e New specific LTE filter for enhanced ACLR performance Depending on the user s requirement the filter can be selected as optimized for EVM Default or optimized for ACP e Time Domain Windowing for uplink and downlink is supported Note that Time D
8. standard is active and predefined settings are used 6000 IEEE 802 11 n Indikator MOD OFF does not disappear when this standard is activated 6042 1 22 Version 2 04 303 03 Released Aug 2007 New Functionality e SMU K54 IEEE 802 11n WlanN e SMU K74 MIMO Fading Fixed Issues CDMA2000 new default setting one channel switch to ON to avoid error messages when setting state to ON 5263 Sometimes a system crash occurs when toggling LEVEL DIAGRAM buttons very often 5353 WiMax Subchannel rotation fixed for uplink PUSC zones including FastFeedback and Ranging bursts Fix in uplink AMC2x3 mode STC Matrix B mode fixed 5355 ARB sine generator error message when using sine generator immediately after switching on EUTRA SMU K55 5356 Custom Digital Modulation List editor system crash when using goto command 5385 FM source is INTERNAL EXTERNAL sensitivity not visible in dialog 5433 W3GPP Enhanced channel 11 selecting config data shows no reaction menu don t open 5542 ARB Loading AMIQ SMIQ waveforms sometimes causes an error message 5597 SCPI all return values of stat is OFF ON instead of 0 1 bug in V2 04 202 only 5610 Custom Digital Modulation user filter doesn t work in path B 5655 CDMA2000 Set To Default resets settings in path A and B not the selected path only 5751 W3GPP error message when selecting PRACH Preamble only with trigger 5801
9. 20 360 142 exe on your PC gt Select Remote Installation C Local Installation Next gt Exit Help Z and click the button Next gt gt After scanning SCPI and your LAN subnet all found instruments are listed Select the instruments you want to update R amp S Software Distributor Device List Please select pour target devices LAA Device v SeralWNo Version SMU 2004 101079 2 05 104 28 O smu 2004 999014 2 05 104 31 SMU 2004 100001 2 05 104 07 100012 2 009 294 ATTENTION Please be careful and check twice if you have selected the correct instruments Depending on your company s network structure also instruments of other departments will show up gt Additonal help will be displayed after clicking the button Help gt Start installation by selecting Install gt Confirm that you want to reboot the instrument in order to activate the firmware update the instrument then restarts automatically 2 Execute internal adjustments gt Press the key on the instrument front panel Press the key select Internal Adjustments and execute Adjust All This process updates internal instrument adjustments and will take several minutes Release Notes for Firmware 1008 0329 52 43 Adjustments requiring external measurement equipment are not affected by the firmware update and need not to be performed 3 Open Source Acknowledgement This instrument firmware mak
10. 24 1 23 Version 2 04202 sicccccssicscssovssscnsenscsensenscscnscnsensnsensecsnsansesensensensnennsesensensessnsensesensensussnes 25 ee all Release Notes for Firmware 1008 0329 52 2 R amp S SMU200A 1 24 Version 2 04 20 cocnncnononicnonononnononcnnnconononnoncnnnononoonononcnnonononon ono rononosnon ono rononocnonononos 25 1 25 Version 2 02 170 oooonocococonnonononnononcnnnrononosnononcnnonononnononcnronononoononcnrorononoonon ono rononosnon ocaso 27 1 26 Version 2 02 145 ococcccococonnononennononcnnnnononosnononcnronononoononcnronononoonon on rorononocnor ono ronononononons 27 1 27 Version 2 02 130 oooonccococinnonononcononcnnnnonononnononcnnonononnononcnronononconon on rorononocnon ono rononnnon caos 27 1 28 Version 2 02 116 oooonocococinnonononnononcnnnononoonononcnnonononnononcnronononnonononroronononon ono rononrron ocaso 28 1 29 Version 2 02 65 oococociononononnnnononcononcncnnonononnononcnconononnononcnronononoonon cn roronononon ono rononosnon caos 29 1 30 Version 1 40 21 cnnoconicnoconinnonononconononcnnonononononcnnonononnononcnronononnonon cn roronononon ono ronosnnon ocaso 30 1 31 Version 1 40 20 oooconicnononinnonononcononcnnnnonononononcnnonononoononcnronononnonon on roronononon ono rononoonon ocaso 30 1 32 Version 14019 eccioninocnconinconconeneonconineonconeneanconinconccnoneanconineoncanen nan ccnincanccneneancanencanianens 30 1 33 Version 1 40 13 s sssssssssosssssssscssssssssssssossssssssssssssssssssssssssssssssssnss
11. WLAN predefined frames not working correctly 4903 WiMax 3GPP clipping not working correctly 4907 WiMax output power not correct when using more than 15 frames 4913 Save Recall exclude frequency and exclude level without impact 5109 Release Notes for Firmware 1008 0329 52 26 R amp S SMU200A Information on the Current Version and History Data lists exceeding 256 Mbyte cannot be loaded to B9 5161 1 25 Version 2 02 170 Released Feb 2007 Fixed Issues Error message I Q out level is below minimum with option SMU B16 4866 Error messages while graphic is running and trigger mode is armed 4885 Sometimes trigger input 1 and 2 does not work immediately after power on 5069 MCCW spectrum not perfect with 3 or 15 carriers 5087 Sometimes a system crash happens at power on 5151 Error message General plugin error in GSM after PRESET and BB GSM MODE SINGLE 5197 syst time xx xx xx and syst date xx xx xx doesn t work anymore 5272 Sometimes system hangup while doubleclicking menu points e g GPIB or Ethenet 5280 1 26 Version 2 02 145 Released Nov 2006 Modified Functionality e Improvement of the level adjustment new internal adjustment level attenuation Fixed Issues GUI Sometimes GUI is frozen after PRESET you cannot open any new window in the application after PRESET GUI Some menus have an unnecessary horizontal scroll bar bug in V2 02 130 only Menu SETUP HARDWARE CONFIG memory leak
12. amp S SMU200A Information on the Current Version and History e Bug fix scrambling for PBCH Uplink e PUSCH frequency hopping type 2 adjusted to v 8 3 0 e DRS group and sequence hopping adjusted to v 8 3 0 e Position of PUSCH DRS in case of extended cyclic prefix changed from 4th symbol to 3rd symbol in slot e Bug fix PUCCH mapping to resource blocks e Bug fix scrambling for PUSCH in case channel coding is activated 3GPP FDD New Features e HSPA Downlink o fixed reference channel H Set 11 e HSPA Uplink o 4PAM modulation for E DPDCH channels o fixed reference channel FRC 8 o HS DPCCH signaling for UEs in MIMO mode Changes e H Sets Now up to 8 HARQ processes are possible up to 16 for MIMO e H Sets Now longer redundancy version sequences for HARQ simulation are possible Problems eliminated e H Sets with HARQ simulation Now the transport block size is signaled only at initial transmissions in HS SCCH types 1 and 3 e The TPC bits in the F DPCH channel were always 0 fixed Wimax New features e Moving Offset mode for Chase HARQ RCT test 9 1 24 e Sub DL UL Maps e Included Ack Disable flag for HARQ subbursts Bugfixes e Fixed available modulation and coding selections for Chase HARQ e Fixed incorrect sounding carrier allocations Release Notes for Firmware 1008 0329 52 18 R amp S SMU200A Information on the Current Version and History 1 14 Version 2 05 222 24 Released Nov 2008 Fixed Issues Pha
13. of AICH and AP AICH channels was incorrect 1 6 Version 2 10 111 189 Released Feb 2011 New Functionality e Support of new processor board FMR9 Modified Functionality e Acomplete list of changed for LTE can be found in the separate document SMx_K55_K69 Release_Notes paf e 3GPP FDD Updated test model TS34121_R8_Table_C_11_1_3 Subtest5 according to the changes in 3GPP TS 34 121 version 8 8 0 Fixed Issues LTE only one out of two installed options K81 used 9920 Drive C is filling up due to internal debug trace files 9202 3GPP FDD Closed loop HARQ feedback 9123 The feedback timing was corrected This can cause the need of recalibration of the additional user delay Sometimes the packets were sent with the wrong redundancy version in case of RSN 3 only for 2 ms TTI length 3GPP FDD Bugfix for the uplink FRC transport block size only for User 9124 FRCs with 2ms TTI size and an E TFCI of 127 APCO Coding could be combined with 8FSK and 16FSK 9138 Internal adjustment may overrule calibration value for reference oscillator 9111 Fading Restart of statistical process not working 9087 BBIN BBOUT have be reinitialized too often 9070 Fading moving profiles may simulate wrong output level 9068 AWGN noise only mode not working with digital baseband output 9066 Listmode not working correctly with external I Q modulation 9065 1 7 Version 2 10 111 153 Released Nov 2010 ae em Release Notes for Firmware 1008 0
14. of PCFICH Support of PHICH Support of PDCCH An arbitraray bit stream PNQ data list pattern is used by the SMx K55 can be uploaded from external if needed and PDCCH processing starts with scrambling see 36 211 6 8 2 The next steps of PDCCH are performed as defined in 36 211 The user is responsible for the content of the several PDCCHs see 36 212 5 3 3 1 DCI Formats and the multiplexing of them SMx K55 does the scrambling layer mapping precoding and RE mapping including permutation and cyclic shifting Uplink Support of new definitions of reference signal sequences Update on demodulation and sounding reference signals Support of group and sequence hopping Supports channel coding for PUSCH including multiplexing of data and control information Supports scrambling of PUSCH e Support of all PUCCH formats eee Release Notes for Firmware 1008 0329 52 21 R amp S SMU200A Information on the Current Version and History 3GPP FDD New Features e HSPA higher order modulation downlink 64QAM CPC HS SCCH less operation MIMO support new H Sets 7 9 3GPP Rel 7 e new H Set 10 3GPP Rel 8 e more flexibility in the H Set configuration User H Set e The user gets support by the user interface for selecting the right ARB sequence length when generating H Set signals e For H Sets the least necessary UE category is displayed e third OCNS Mode HSDPA 2 according to TS 25 101 e E AGCH now
15. revision consists of only one file SMU200A_2 20 360 142 exe There are two possible ways to update your instrument Local Firmware Update The firmware update is performed directly on the instrument typically using an USB memory stick Mouse and keyboard have to be connected to the instrument For instruments without front panel display like the SMATE an external monitor is required too The appropriate VGA plug is located on the rear panel The front panel keys like or can be emulated performing a right click on the block diagram See Chapter 2 1 for details Remote Firmware Update Alternatively the firmware update can be performed over LAN or SCPI from an external PC running Windows XP Connect the instrument via LAN or SCPI to the PC and run the firmware update from the PC See Chapter 2 2 for details ATTENTION Important Note for updating without SP2 A Please contact your local R amp S service department in order to update your instrument Alternatively the needed files and packages can be installed manually In this case download the file SystemSetup4SignalGenerators zip and follow the instructions given in readme txt Release Notes for Firmware 1008 0329 52 40 R amp S SMU200A Firmware Update 2 1 Local Firmware Update 1 Save the current version It is recommended to save the current running version This can be done very easily and completely intuitive with an USB keyboard and an USB mouse e Switch off
16. 2 29 R amp S SMU200A Information on the Current Version and History sporadic erros in output signal when l Q graphic is running 4214 block diagram with BBIN without baseband block incorrect 4495 SCPI commands FSIM DEL GRO lt group gt PATH1 CORR only working for group1 4640 1 30 Version 1 40 21 Released April 2006 Fixed Issues e WLAN save recall not possible if CDMA2000 and 3GPP FDD is not available e Bugfix with new calibration data from level RFM V2 0 internal use only 1 31 Version 1 40 20 Released March 2006 Fixed Issues e DSP communication error sometimes occurs only in V1 40 19 fixed e Bugfix with new calibration data from level RFM V2 0 internal use only 1 32 Version 1 40 19 Released Feb 2006 Modified Functionality e New level calibration for factory purposes supported e Improvement of settling time with IQ modulation on Fixed Issues e In rare cases the level adjustment failed with error DACIF fixed 1 33 Version 1 40 13 Released Nov 2005 New Functionality e Generation of HSDPA H Sets SMU K44 Release Notes for Firmware 1008 0329 52 30 R amp S SMU200A Information on the Current Version and History e Support of WiMAX OFDMA mode SMU K49 e Support of ARB multi carrier e Support of parameter variation with mouse wheel Modified Functionality e UCOR level range extended to 100 dB e Several improvements of file dialog e Several improvements of AWGN dialog SMU K
17. 329 52 9 R amp S SMU200A Information on the Current Version and History New Functionality e SMU K8 amp 1 LTE logfile generation e SMU K253 Playing of DAB TDMB waveforms Modified Functionality e Acomplete list of changed for LTE can be found in the separate document SMx_K55_K69 Release_Notes paf e Fading fading HST now available in MIMO2x2 e Module support newest release 7 of B9 B10 B11 supported e New icon at desktop and tray bar to ease returning from remote desktop e ARB sequencing several improvements e 3GPP FDD all supported features are in line with release 9 of the 3GPP specifications e Fading new profile watterson available Fixed Issues Fading Remote commands for Kronecker parameters not working for 8991 higher MIMO modes CW Modulation switching using control lists not working reliably at lower 8969 symbol rates 1xEVDO sporadic overdriving in base band domain spectral regrowth 8903 Fading HST profile not working reliably at very high speeds 1500 km h 8859 Blockdiagram AWGN block not displayed correctly if no B9 B10 B11 is 8855 installed 3GPP FDD HARQ feedback The feedback timing was corrected This 8888 can cause the need of recalibration of the additional user delay Sometimes the packets were sent with the wrong redundancy version in case of RSN 3 only for 2 ms TTI length Fading optimized handling of conflicts changing the correlation matrix 8730 FM Stereo instabilities using a
18. 62 Fixed Issues List Mode dwell time of first step not correct 2703 Custom DigMod support of CW switching incorrect 2966 SYST SERR does not respond no error if everything is ok 3225 Changing the remote interface VXI11 lt gt GPIB causes crash of instrument 3360 ARB no independent sine test signal output possible on path A B 3365 Pulse modulation deactivates digital modulation 3687 Internal graphics stopps when both paths are triggered by marker 1 3699 3GPP FDD TFCI setting of S CCPCH not allowed 3716 List mode online help missing 3849 FM external impedance only switchable if FM is ON 3870 Setups of older firmware versions cannot be read 3877 Power on preset not working 3879 All standards units of single trigger duration harmonized 3892 Input of values with leading floating point eg 5 not supported 3906 Pop ups not operable without mouse eg ARB multi segment 3911 Fading insertion loss not working correctly 3917 Multi carrier SCPI unit dB not accepted 3938 Sweep Attenuator switches in fixed mode occasionally 3966 Power Up Down RF level not supported by remote interface 3973 All standards SCPI instrument crashs when pattern length exeeds 32 3987 3GPP FDD Update problem when changing UE4 paramaters with active addional Ues 3992 WLAN given RF level not referred to burst power 4012 Multi carrier Set To Default does not reset output signal 4015 Custom DigMod symbol rate remains unchanged after reca
19. Bugfixes e Fixed bug in HARQ CRC e Fixed pilot carrier bug for 4 Antenna STC modes e Fixed dedicated pilot flag in DL MAP for PUSC GPS e Unlimited Play Time e Satellite Elevation Mask made configurable 2 5 5 7 5 and 109 e Satellite Handover Based on Optimal Availabilty Algorithms in AUTO SV UPDATE Mode e Ephemeris Projection in AUTO SV Modes overcoming the 2 hours Ephemeris validity Problem e 3GPP2 CDMA2000 Test Scenarios available ee oe ices Release Notes for Firmware 1008 0329 52 15 R amp S SMU200A Information on the Current Version and History e Sensitivity Assistance Data CDMA2000 available e SPOT view Satellite Receiver View HDOP PDOP Next Handover Query 1 13 Version 2 05 222 34 Released Jan 2009 New Functionality e SMU K41 GSM EDGE e SMU K60 Bluetooth Modified Functionality e Fading Simulator SMU K74 now also supports 2x3 3x2 2x4 and 4x2 MIMO scenarios e Fading Simulator When 2x2 MIMO fading is active the definition of RF level has been changed older versions the level is the effective level like it would be without fading current version the level is the nominal level the effective level may be below due to impairments caused by the correlation matrix e RF can be optionally blanked when external reference is missing e Chinese online help now available e Internal adjustment uses external reference oscillator if selected and connected e List mode sub mode STEP
20. MU K6 Support of external Pulse Sequencer Software eee a Release Notes for Firmware 1008 0329 52 25 R amp S SMU200A Information on the Current Version and History Modified Functionality e TD SCDMA Predefined Settings Testmodels e NRP power sensors persistent power display in block diagram e List mode level setting without interruption blanking e ARB Multi segment several improvements bugfixes e Armed Triggered state visible in block diagram e Security Menu possibility to switch off USB port and LAN for file transfer e New optimization mode high quality to reduce modulation frequency response 3GPP e 3GPP HSDPA H SET6 Extensions e 3GPP HSUPA Extensions E DPDCH with new symbol rates 15ksps and 30 ksps separate channel powers possible HARQ State WiMAX e HARQ e Offline Filter e AMC 2x3 e Fast Feedback Bursts e Dedicated Pilots for AMC 2x3 and PUSC e Switchable Subchannel Rotation for Uplink PUSC e DCD and UCD Bursts e New modulation QAM 5 6 e Extension of DL MAP CID SWITCH IE bursts of all zones MAC Header and CRC on Enhancements of fading and noise e TETRA Fading DR50 DU50 e AWGN Extended S N Range 50 dB to 30 dB Fixed Issues ABB test sine signals some remote commands not working 4376 CustomDigMod FSK envelope not constant with root cosine filter and some roll off factors 4763 ARB sequence length maximum depending on ARB size 4815 3GPP FDD Save waveform not working for uplink 4850
21. R amp S SMU200A Vector Signal Generator Release Notes Firmware Version 2 20 360 142 2012 Rohde amp Schwarz GmbH amp Co KG 81671 Munich Germany Printed in Germany Subject to change Data without tolerance limits is not binding RES is a registered trademark of Rohde amp Schwarz GmbH amp Co KG Trade names are trademarks of the owners The following abbreviations are used throughout this document R amp S SMU200A is abbreviated as R amp S SMU200A Test and Measurement Release Notes R amp S SMU200A Table of Contents 1 INFORMATION ON THE CURRENT VERSION AND HISTORY 5 WED AAA eere aaee a Eee R ANE OENE re Eea E Tebi SEENE roians 5 1 2 Version 2 20 360 68 ssssssssssrsssssssrsssesssssssvssssasssssssrossssssasssssssrssssssrasssssssrssssssrssssssssss 5 1 3 Version 2 20 360 54 uu ssssssscsecssscsecnesseseenessesecnessssecnersesecnersesecsessesecserseseeserseseeees 5 1 4 Version 2 202230 131 o nicsisccecccisisnsccsccessiscssonsieinsseccecvscndcesesesscncveceoceissendcecstescssssennsucsveses 6 1 5 Version 2 20 230 58 csscscssssessessscesssnssssesssssssssessessssestsnsscsesessssessssessessesesssseres 7 1 6 Version 2 10 111 189 ocoicnononoimmmsmmmmmsmmmmmmmrmmmr 9 1 7 Version 2 10 111 15B oooococicionononiononenonnononcnnonononcononcnconononnononcnronononncnononrorononcnoncnrononoso 9 1 8 Version 2 10 111 116 ononnociciononononnnnononnononcncnnonononnononcnronononcononcnrorononoc
22. Sometimes ALC problems with pulsed 1 Q signals fixed 10242 ARB problems with corrupt data lists fixed 10225 Fading Hopping doesn t work in path B only V2 20 xx fixed 10184 W3gpp GUI problems with DLIST in downlink channel table fixed 10171 AWGN correlation between path A and B in MIMO cases fixed Release Notes for 3GPP FDD e The PCPCH message part was incorrect for user equipments 2 to 4 Fixed e The Scheduling List dialog could make the user interface freeze for up to a minute if a large number of frames was displayed Fixed 1 2 Version 2 20 360 68 Released March 2012 Fixed Issues ARB Memory overflow when loading gt 100 different waveforms 10069 General instruments without AWGN option K62 may have wrong RF level 10060 BBIN output level may be wrong when switching sample rate between 100 9742 MHz and user defined 1 3 Version 2 20 360 54 Released February 2012 New Functionality e SMU K77 A amp D Fading e SMU K85 LTE Release 10 Advanced Release Notes for Firmware 1008 0329 52 5 R amp S SMU200A Information on the Current Version and History e SMU K87 1xEV DO Rev B e SMU K353 DAB waveforms e SMU K354 T DMB DAB waveforms e SMU K266 Galileo waveforms generated with WinlQSIM2 e SMU K294 Glonass waveforms generated with WinlQSIM2 Modified Functionality general e GSM slot attenuation extended to 70 dB e Service Counter for high power relay implem
23. a Release 2 e SMU K69 LTE closed loop BS test e NRP Z power sensors Info and update dialog from Setup e ARB Sequencing with play lists Modified Functionality e RST key has been speeded up e ARB multi segment mode several improvements single trigger with different clock rates e ARB multi carrier mode support of clipping e External triggering choice between sync to external trigger with skipping first samples default and outputting from first sample new e All digital standards setups can now be saved in differential format Release Notes for Firmware 1008 0329 52 11 R amp S SMU200A Information on the Current Version and History e Optimized file dialog tree view e Sweep new mode Extern Start stop e Custom Dig Mod new modulation AQPSK e AWGN C N range extended to 40 dB e Head panel Frequency level and status information renewed e Internal Graphics can be controlles remotely eg SOUR BB GRAP SMAR STAT ON SOUR BB GRAP STAT ON e 3GPP FDD Uplink Signaling in HS DPCCH channel for DC HSDPA e Bluetooth Upgraded to Core Specification 4 0 and added Lowe Energy Enhancements e Several enhancements for LTE EUTRA see separate release notes e SMU K80 BERT BLERT timeout introduced e ExBox Default for word alignment changed from MSB to LSB Fixed Issues RST during manual or vice versa may lead to crash 6487 Search function in online help improved 6637 Leading 0 is network addr
24. caused system hangup 5025 Testcase Wizard error message Fader Insertion Loss Limit Exceeded value set to limit when using test case 8 4 with antenna diversity ON 5034 4884 1 27 Version 2 02 130 Released Sept 2006 New Functionality e Support of new main board with FMR7 first version O on U OHM Release Notes for Firmware 1008 0329 52 27 R amp S SMU200A Information on the Current Version and History e New menu SETUP UPDATE for updating internal FPGA Fixed Issues Custom Digital Modulation vam files couldn t be selected via IEEE bus 4270 Custom Digital Modulation symbol rate not accessible via GUI 4845 Option SMU B16 error message I Q out level is below minimum for optimize 1 Q signals for RF output enabled sometimes doesn t disappear V2 02 116 only 4866 Fading insertion loss USER does not work with high crest factors wrong output level and error message all V2 02 xx affected 4868 Fading 2 Channel Interferer state not accessible via IEEE 4910 1 28 Version 2 02 116 Released Aug 2006 New Functionality e Support of new digital standard DVB SMU K52 e Support of new option SMU K256 WinlQSIM2 XM RADIO Modified Functionality e Power sensor Offset mode implemented e TD SCDMA new marker mode Frame Active Part e Internal adjustment reference frequency mode not changed to internal during internal adjustment e GPIB channel address now saved immediately to support hard
25. cheduling of E DCH packets now is possible in a more flexible way The former DTX patterns have been replaced by an E DCH scheduling table This does not apply for E DCH fixed reference channels FRCs with enabled HARQ Simulation The E DPCCH and E DPDCH channels now are generated in real time if UL DTX or dynamic power control is activated e HSPA Uplink e UL DTX now is possible also for other channels than DPCCH The configuration of two UL DTX cycles is possible and all dependencies between the transmissions of the channels are taken into account in line with 3GPP TS 25 214 Now dynamic power control is possible also in combination with UL DTX The application of externally received power control commands is made in compliance with 3GPP TS 25 214 UL DPCCH gaps are taken into account e Real time generation of the HS DPCCH channel now is possible also if the HS DPCCH contains HSPA content Fixed Issues e General eel Release Notes for Firmware 1008 0329 52 8 R amp S SMU200A Information on the Current Version and History The code allocation for compressed mode method SF 2 was incorrect e General Uplink The PCPCH Channel Coding was not working correctly Data sources were read out at the wrong positions in case of uplink compressed mode method SF 2 e General Downlink e In certain cases the TFCI state of DPCH channels was configured to be off DTX after selecting a reference measurement channel The generation
26. cononcncnnonononnononcnronononncnononronononnononcnroronononon ono rononrnon carnes 37 1 47 Version 1 10 08 ocococnonocononnonononnononcnnnronononnononcnnonononnonononronononnonon cn roronononor ono rononrron caos 37 1 48 Version 1 04 14 cnoocciccocononnononononnoncncnronononnononcnronononncnoncnronononnonon cn roronononon ono rononooron ocaso 38 1 49 Version 1 04 13 nnocncncnonononnononincononcnnnnononosnononcnronononnononcnronononnonon on roronononon ono rocononon caros 38 1 50 Version 1 04 11 occocociononononnnnononcononcncnrononosnononcnronononcononcnronononoonononrorononocnon ono Esae esoe ssas 38 O on l U M Release Notes for Firmware 1008 0329 52 3 1 51 Version TOA vccccctecccsscetesssscvecsosscesdeconssoesesscosincesstesesssasideresesssasoosesdsesscencosbnsasdsveseceses 39 2 FIRMWARE UPDATE cccicioniaiinsaia ii iii 40 2 1 Local Firmware Update wic sccscscesssccssisssccicvssscnscedceschasscscesceasessaasacesnscedsescsasacesaacvasescacds 41 2 2 Remote Firmware Update esesesssescsescscscsescsescscecscscsescseseeesesescsesesesesesesesesesesesesese 43 3 OPEN SOURCE ACKNOWLEDGEMENT c ccccssssssssseeeessseees 45 4 CUSTOMER SUPPORT soriana rr 46 R amp S SMU200A Information on the Current Version and History 1 Information on the Current Version and History 1 1 Version 2 20 360 142 Released July 2012 Fixed Issues Fading Insertion Loss in path B doesn t work only V2 20 xx fixed 10281
27. d in the separate document SMx_K55_K69 K81_K84_Release_Notes pdf Release Notes for 3GPP FDD New Features e General Uplink Instead of specifying the level of the total signal i e the average power it is possible now to specify the level during specific parts of the signal like e g during the PRACH message part or during the first slot with active DPCCH by specifying a level reference e The scheduling of uplink signals now can be visualized in a scheduling list e HSDPA Downlink e The leveling for H Set fixed reference channels was simplified by introducing the possibility of configuring the total HS PDSCH power e HSPA Downlink e The modulation and number of HS PDSCH channelization codes in H Set fixed reference channels now can be randomly varied over time as needed for type 3i enhanced performance requirements tests e The generation of the other user s channels OCNS for type 3i enhanced performance requirements tests is possible now Changed Features e General Uplink The 1024 chips delay of the uplink signal can be switched off now if needed e HSDPA Uplink e The scheduling of HS DPCCH transmissions now is possible in a more flexible way e Real time generation of the HS DPCCH channel now is possible also in case the HS DPCCH is scheduled by the HS DPCCH scheduling table e HSUPA Uplink e The generation of E DPDCH channels now can be restricted to the or Q branch if needed e The s
28. did not preset fading parametes fixed 7440 EUTRA LTE Downlink e TDD special subframes automatic adjustment of parameters is now fully supported Uplink e PUSCH allocations are now displayed correctly in the time plan for frequency hopping type EEES ss AAA Release Notes for Firmware 1008 0329 52 14 R amp S SMU200A Information on the Current Version and History e PUCCH allocations and PUCCH region is displayed in the time plan e PRACH is displayed in the time plan Fading e New fading profiles for 1x2 4x2 und 4x4 ETU300 and HST 3GPP FDD New Features e HSUPA HSPA Uplink o Fixed reference channels FRC Transport block size and channel allocation now is user configurable User FRC o Uplink test models according to TS34 121 tables C 10 1 4 C 11 1 3 C 11 1 4 e HSPA Uplink o Uplink DPCCH slot format 4 o UL DTX mode for CPC simulation DPCCH Gating e HSPA Downlink o F DPCH slot formats 1 to 9 Enhanced F DPCH o Fixed reference channel H Set 12 for Dual Cell HSDPA tests DC HSDPA o Downlink test models for Home base station tests Home NodeB Changes e Support for old release 4 uplink DPCCH slot formats 4 and 5 is discontinued Problems eliminated e Uplink compressed mode The configuration of TG pattern 2 was not recognized correctly Wimax New features e 2 Antenna STC modes Matrix A and B for AMC2x3 e Power offset of Baseband B e MIMO UL Basic IE added to UL MAP
29. e fader fails improved Fixed Issues e Fader menu of Path Table filled with when no option SMU K42 is installed 1 42 Version 1 20 32 Released Jan 2005 Fixed Issues e The carrier leakage is bad after switching on the device Executing the l Q modulator adjustment makes it good until to the next power on fixed e Fading The insertion loss displays a wrong value in mode NORMAL fixed e Sometimes a system crash occurs at power down fixed 1 43 Version 1 20 31 Released Dec 2004 New Functionality e Support of Fading Simulator Option SMU B14 e Support of Fading Simulator Extension Option SMU B15 e Enhanced Resolution and Dynamic Fading Option SMU K71 Fixed Issues e Setting the RF phase leads to system hang fixed Release Notes for Firmware 1008 0329 52 35 R amp S SMU200A Information on the Current Version and History e Problem with user step level variation fixed e Problem regarding Device Clear DCL fixed 1 44 Version 1 20 17 Released Sept 2004 New Functionality e Support of 3GPP FDD including HSDPA Option SMU K43 e Support of CDMA2000 Option SMU K46 e Support of 16 Megasample Modulation Generator Option SMU B11 e Support of Multisegment Arbitrary Waveform Modified Functionality e Improved 3GPP FDD PRACH capabilities e g channel coding in UE2 to UE4 e Code domain display for 3GPP FDD uplink e User definable slot markers for GSM e Several improvemen
30. ented e Fading External trigger possibility without modulation coder implemented Fixed Issues Command SOUR IQ OUTP EXT LOG TYPE SSI28 not working 10033 Fading Knonecker parameter not correctly implemented for 2x3 and 3x2 10027 Command BB C2K LINK Forward Reverse not working 10013 Chinese online help shows some strange characters 9992 Release Notes for LTE EUTRA can be found in the separate document SMx_K55_K69_K81_K84_K85 Release_Notes pdf Release Notes for 3GPP FDD General Increased the dynamic range for dynamic power control to 60 dB if the power step size is at least 1 dB HSUPA Uplink Selection between LEVATT and USER 1 connectors for HARQ Feeback 1 4 Version 2 20 230 131 Released December 2011 Known Issue Firmware Update by GPIB requires a manual reboot after installation Fixed Issues ARB multi segment Append button missing 9945 Patch DII OrgLayer dll from V2 20 230 58 now integrated in the package 9946 ESR Bit 6 is set when going to LOCAL 9549 All digital modulations Armed trigger is ignored in rare cases 9905 Release Notes for LTE EUTRA can be found in the separate document SMx_K55_K69_K81_K84_Release_Notes pdf ee all Release Notes for Firmware 1008 0329 52 6 R amp S SMU200A Information on the Current Version and History 1 5 Version 2 20 230 58 Released July 2011 New Functionality e SMU K84 LTE Release 9 e SMU K86 IEEE 802 11 AC Modi
31. es use of valuable open source software packages The most important of them are listed together with their corresponding open source license information in a separate Open Source Acknowledgement document This document also contains the verbatim license texts and can be downloaded from www rohde schwarz com The OpenSSL Project for use in the OpenSSL Toolkit htto www openssl org includes cryptographic software written by Eric Young eay cryptsoft com and software written by Tim Hudson tjh cryptsoft com LINUXO is a trademark of Linus Torvalds Rohde 8 Schwarz would like to thank the open source community for their valuable contribution to embedded computing R amp S SMU200A Customer Support 4 Customer Support Technical support where and when you need it For quick expert help with any Rohde amp Schwarz equipment contact one of our Customer Support Centers A team of highly qualified engineers provides telephone support and will work with you to find a solution to your query on any aspect of the operation programming or applications of Rohde amp Schwarz equipment Up to date information and upgrades To keep your instrument up to date and to be informed about new application notes related to your instrument please send an e mail to the Customer Support Center stating your instrument and your wish We will take care that you will get the right information USA amp Canada Monday to Friday 8 00 AM 8 00 PM
32. esses removed LXI and Ethernet dialog 6692 Lost focus in edit field validates entry 7383 Setting range for I Q impairments limited to 10 formerly 50 7796 Custom Dig Mod Formula for calculating modulation index has been 7952 corrected to m max min max min BBOUT output level has been too low when internal driving was below 7958 6dbfs Marker info missing when generating waveform from digital modulation 7971 signal Fading level correction due to asymmetric correlation matrix was not 7980 referring to RMS but to Peak value Recursive trigger dependencies between basebands A and B eliminated 7983 B90 sometimes error message appears during adjustment 7989 Fading MIMO modes 4x2 and 3x2 not working correctly for subset 2 7994 Fading dynamic scenarios like high speed train can now be combined 7997 with Mimo 1x2 BBIN overload and auto level set not working reliably 8018 Custom Dig Mod several minor problems with CList editor and 8022 documentation Fading Remote read function for frequency ratio 8106 FSIM DEL GRO1 PATH2 FRAT did not consider fading mode Q impairments Optimization mode changed l Q bandwidth ignored 8121 TD SCDMA remote commands 8123 BB TDSCdma UP CELL1 SLOT1 PRAC MSG DATA PATT and 8124 Release Notes for Firmware 1008 0329 52 12 R amp S SMU200A Information on the Current Version and History BB TDSCdma UP CELL ENH DCH HSUPA BPAYload Not working SCPI octal pattern eg Using with data sources not wor
33. fied Functionality e LXI Webserver VNC viewer integrated e Remote Emulation of other instruments possible changing IDN and OPT responses e GSM Support of VAMOS AQPSK modulation e ARB multi carrier arbitrary carrier spacing possible e Custom DigMod support of APCO25 8PSK e Support of RF frequency multipliers e GSM extended range for trigger delay Modified Functionality for Fading Simulator SMU B14 B15 e Support of SCM Fading AoA AoD e New Fading Profile Standard TI5 for GSM e New Fading Profiles for 3GPP e New Fading Profiles for LTE MBSFN e Extended HST Fading double speed e Correlation Matrix now also available with static path fading profile and extended resolution e GSM Support of VA Fixed Issues Changing slope for baseband trigger and clock without effect 9265 All remote commands starting with sour iq outp ext or sour bbin not working properly 9284 Adjustment of complete path B not possible with only one baseband option and installed K55 9409 Some help issues 9465 Digital 1 Q Interface transmission of sample rate to receiver missing after soft reboot 9599 K48 WLAN problems setting duration in Single Trigger mode 9673 Instruments with 2xB13 and B14 but no B15 show strange block diagram 9679 O on l mE Release Notes for Firmware 1008 0329 52 7 R amp S SMU200A Information on the Current Version and History Release Notes for LTE EUTRA can be foun
34. ible for service purposes 1 38 Version 1 30 12 Released May 2005 Modified Functionality New GSM EDGE External trigger source external clock added Fixed Issues Menu LF Output value for output voltage not visible you see lt null descriptor gt instead of the correct value bug only in version 1 30 10 fixed 3GPP FDD and MCCW Trigger in external trigger delay does not work fixed Fading Insertion Loss Configuration Mode User Switching off the fading state with an insertion loss value unequal 0 affects the output signal worst case when setting the value to 30 dB your output signal is minimal fixed 3GPP FDD power setting of uplink HS DPCCH has no effect fixed 1 39 Version 1 30 10 Released April 2005 New Functionality New 3GPP FDD Test Case Wizard according to TS25 141 New AWGN mode CW Interferer and reference mode Support of new motherboard with Differential l Q Out Option SMU B16 Fixed Issues Fading Insertion Loss Configuration Mode Low ACP and user improved Common loading of ARB waveforms accelerated ae ell Release Notes for Firmware 1008 0329 52 34 R amp S SMU200A Information on the Current Version and History 1 40 Version 1 20 34 Released March 2005 Modified Functionality e Internal tests of fader improved 1 41 Version 1 20 33 Released Feb 2005 Modified Functionality e Inrare cases the selftest of th
35. ing modulation 4FSK with coding GSM fixed now no selection of coding GSM with modulation 4FSK allowed e GSM EDGE switching to external clock produces an error message settings conflict fixed e Sometimes no min max check while changing parameters via rotary knob fixed e No capitals with external keyboard possible i e file dialog fixed e CList editor cursor left right has no function fixed now same functionality as rotary knob e Sweep setting a new frequency in mode STEP results in a wrong output frequency always max value of step mode fixed e Sweep mode STEP variation with rotary knob works til min max is reached then no further variation possible fixed 1 37 Version 1 30 13 Released June 2005 Modified Functionality e Improvement in l Q calibration better side band suppression Fixed Issues e GSM EDGE Editing the slot defined marker results in a system crash fixed e Fading Changing parameter speed or delay while insertion loss USER is active causes a wrong output power fixed ee ees Release Notes for Firmware 1008 0329 52 33 R amp S SMU200A Information on the Current Version and History Digital modulation FSK with coding GSM produces an error message fixed List mode with high power option max value for power is now 30 dB not 20 dB fixed Error messages from DAC Board occurred in devices without baseband source fixed Internal setting of operation time and power on count poss
36. king 8129 Wimax IE TLV Encoded information for the overall channel Frame 8233 Duration Code Frame Number missing 1 10 Version 2 05 269 101 Released Oct 2009 Fixed Issues Sometimes an error message DSP unknown command appears at first 7920 switching on a digital standard fixed Sometimes error messages occurs from modulation coder DSP and at last 7919 Zero signal measured gt Modulation coder output deacivated and no output signal is available more often with GPS fixed AWGN doesn t work correctly in V2 05 269 xx with DacBoard 7918 1141 8090 xx only fixed 3GPP Test Case Wizard frequency offset CW with TC 7 6 does not accept 7857 negative values via IEEE fixed Fading Mimo2x3 and 2x4 Displayed value for MIMO Fading Power 7820 Correction with MIMO subset 2 wrong subset 1 is ok fixed Blanking of output signal improved now as few as possible 7818 ARB Same Segment Single Trigger Sequence Length Unit Samples 7816 does not work correctly fixed 1 11 Version 2 05 269 83 Released Jul 2009 Fixed Issues ist returns always 1 error fixed 7760 List mode error message while learning list fixed 7752 1 12 Version 2 05 269 77 Released May 2009 New Functionality e SMU K58 Sirius e SMU K352 Playback of HD Radio streams Release Notes for Firmware 1008 0329 52 13 R amp S SMU200A Information on the Current Version and History Modified Functionality e List mode
37. lQSIM2 options K2xx e Support of NRP Zxx power sensors power viewer and user correction e Generate Waveform File for all digital standards for multi carrier multi segment Modified Functionality e Support of user filter files generated with R amp S FiltWiz e Import of list mode and user correction data from CSV and TXT files e WiMAX SMU K49 several extensions including WiBro and multi zones e BBIN SMU B17 Several improvements e 3GPP FDD SMU K43 parameter range of BER BLER extended to 50 3 power steps for HS DPCCH e Setup menu Display of instruments TCPIP address and BIOS version e Unit keys k M now working as multipliers for parameters with only one unit eg 38 4 k gt 38400 e list mode frequency and level display dotted when list mode running e SCPI Error Queue entries with path indication A B e phase modulation unit rad and degree supported attention default is rad now Fixed Issues Renaming files with MMEM MOVE did not work 2875 Eye diagram did not work correctly 3417 Save Recall with MMEM LOAD STAT MMEM STOR STAT not working 3473 3GPP HSDPA bursts have been cut instead of wrapped around at end of sequence 3902 Fading clipping display not working correctly in all modes 3918 sporadic crashes when handling big ARB waveforms 4026 inconsistent block diagram in REMOTE state 4029 SCPI commands for ARB multi segment SOUR BB ARB WSEG missing 4210 Release Notes for Firmware 1008 0329 5
38. lay of hardware equipment hardware revision software revision and instrument options e Several optimizations for two path operation e Added 3GPP Compressed Mode Release Notes for Firmware 1008 0329 52 38 R amp S SMU200A Information on the Current Version and History e Resolution of trigger delay changed to 0 01 symbol Note The front panel key RECALCULATE is provided for future use and has no function yet Fixed Issues e mV and pV unit keys When entering a level value using the mV and uV keys of the R amp S SMU keyboard the maximum level was set This is fixed e SCPI commands SCPI command chains separated by semicolons were treated wrongly when parts did not start with a colon This is fixed e 3GPP Reference Measurement Channel Coding Bug in 3GPP Reference Measurement Channel Coding is fixed e 3GPP Uplink Slot assemblies DPCCH and DPDCH and Data Source DPDCH are now displayed e Save Recall Checkbox Exclude Frequency is functional now e User Correction Editor now creates new lists 1 51 Version 1 04 11 Released Sep 2003 First Release Release Notes for Firmware 1008 0329 52 39 R amp S SMU200A Firmware Update 2 Firmware Update ATTENTION It is strongly recommended to do no firmware downgrade below the version the device was delivered originally this is the version you can see if you select Factory Default starting with Backup Recovery This R amp S SMU firmware
39. ll 4066 CDMA2000 SCPI command BB C2K MSTation1 CHANnel1 DATA RATE not working 4088 3GPP FDD progress bar missing after fast parameter change occasionally 4094 Some standards pattern editor not operable after leaving with ESC before 4096 All standards trigger delay ignored when trigger source is other baseband 4117 WLAN chip rate can be set to 100 MHz fixed limited to 40 MHz 4132 Range of level in attenuator fixed mode wrong occasionally 4138 Displayed baseband signal level wrong with fading and or AWGN 4174 Sometimes no baseband signal with external clock and internal trigger 4176 Fading Birth Death Propagation delay grid minimum wrong check of offset hopping dwell missing 4188 swe res all does not work 4195 Release Notes for Firmware 1008 0329 52 31 R amp S SMU200A Information on the Current Version and History 1 34 Version 1 35 14 Released Sept 2005 Modified Functionality e Improvement of Calibration 1 35 Version 1 35 13 Released Aug 2005 Modified Functionality e Loading from setups from elder versions improved Fixed Issues e n rare cases the message Device key missing at start of the instrument occurs fixed 1 36 Version 1 35 10 Released July 2005 New Functionality e Support of digital standard SMU K44 GPS e Support of digital standard SMU K48 WLAN IEEE 802 11 a b g e Support of digital standard SMU K49 WiMax IEEE 802 16 d e phase offset available in baseband block menu
40. ne file and over LAN e LXI Class C including web server e Sophisticated hardcopy function e Factory preset standard Preset RST does not reset reference oscillator or power on state level e Several layouts of external keyboards supported e All windows can be resized in height using lt REARR gt button e Busy display for Preset Save Recall and switching digital standards e Fading Simulator new profiles 3GPP high speed train and 1xEVDO e Custom Digital Modulation support of QAM128 several improvements of data list editor e All sweeps support now shapes sawtooth and triangle e Phase continuous frequency setting e Setting times for level frequency reduced by typ 150 us e Display of NRP Z81 peak power e SMU B17 BBIN Extended setting range for PEP and crest factor Fixed Issues Several hyperlinks in online help not working fixed 5323 Construction of multi segment waveform in path B erroneous 5366 Out of memory calculating dynamic fading scenarios fixed 5961 Fading standard 3GPP VA30 UE does not set all parameters speed fixed 6269 Level sweep without dropouts fixed 6533 Trigger not stored in multisegment waveform fixed 6589 Several bugs with multi segment waveform fixed 5205 ARB file selection dialog improved tool tipp with all comments fixed 5884 DigMod Pure Gauss parameter not accessible from SCPI fixed 6168 Several small changes in user manual online help fixed 6334 DigMod 16QAM Edge not
41. nononroronononon ones 11 1 9 Version 2 10 111 53 coococicnocociononononnnnononocnononcnnonononnononcnronononnonononroronononononroronononon caos 11 1 10 Version 2 05 269 101 sssscscsssssssssssssssssscesesessssssesesesesessssnssssssecesesesseseseseeesenenes 13 1 11 Version 2 05 269 83 cssssscscssssssssssssssssesecesesessssssssesssesesessnsesessesesesessssesessesesees 13 1 12 Version 2 05 269 77 coococionononinoononcnnanononosnononcnoonononnononcnronononoononcnnoronononor cn rorononrinon raros 13 1 13 Version 2 05 222 34 ccocciccoconiononononnnonononononcnnonononcononcnronononnonononcoronononon ono rononrnon cars 16 1 14 Version 2 05 222 24 cccococicnononiononononnnnononosnononcnconononcononcnronononoonononcoronononon on rorononnnon ones 19 1 15 IA AAA 19 1 16 Version 205 104 B4 sssr caess noo cocccccandsveseeseccsccgotsesssecoseescgetactees se ssosdesveososececeasecetes 19 1 17 IAEA AAA 20 1 18 AAN E EA A sesos s isser asses o vistia 23 1 19 Version 2 04 3033 1 wsiciiccsccsscssssnisesecesscecvsesscesnseessecvssnscssesessencvectscesssesscecsserocsaveentoasese 23 1 20 Version 2 04303 7 sccsscsccsscsccscscsacescescecdass cvusseseccascecsssvsoeseasocsgesccseeesessascucesovosessssessestes 23 1 21 Versi n 2 04303 16 ciicciscsscssssssnsssssecscssssonsecdnesessecvensvacsesctscecvesesoesessndscssecvonstsssntsesees 23 1 22 Version 2 04 303 03 sicscccscscececscissvsstcecesdcacssesssassccvecasesssessscocendsocsesevessuesaseccsesvessuscsatscssen
42. omain Windowing in the downlink will degrade EVM substantially due to the definition of the EVM in 3GPP e Enhanced Test Models 36 141 are supported by means of setup files Downlink e Support of TDD e PHICH The configurable ACK NACK pattern 8 bits for normal CP 4 bits for extended CP for one PHICH group now consists of 1 0 and DTX Uplink e Update to 3GPP version 8 3 0 PUCCH PUSCH e n_PRS updated to version 8 3 0 e Support of PRACH Changes and Bug fixes Downlink e Initialization of PRS generator X2 is selectable between v 8 2 0 and v 8 3 0 default This has an effect on the reference signals scrambling and PHICH mapping N_c will be fixed to 1600 as defined in 3GPP in case of v 8 3 0 e Control region for PDCCH extended to 4 symbols in case of small channel bandwidths lt 10RBs e Scrambling can be activated individually for PCFICH and PDCCH e Power levels can be set individually for PCFICH PHICH and PDCCH Power setting for PHICH is applied to every single ACK NACK BPSK symbol Normalization of a PHICH group not yet defined in 3GPP can be achieved herewith e Bug fix PHICH mapping in case of extended cyclic prefix e Normalization for transmit diversity as defined in 36 211 added e Added dependencies for User PDSCH allocations all user allocations use the same settings for modulation pre coding scrambling and channel coding Release Notes for Firmware 1008 0329 52 17 R
43. power off e PhaseModulation SCPI default unit changed from degree to rad due to SCPI norm e 3GPP Power Control new marker mode Dynamic Power Control for marker 4 Fixed Issues GSM EDGE Recall Predefined Frame cannot copy to frame 2 4074 Custom Digital Modulation ASK graphic for Modulation Settings empty 4131 ARB Multi Segment Recall GUI Problem 4623 Multi Carrier Division by zero if all carriers are switched off 4639 WLAN Generate Waveform File doesn t work 4665 ARB wv files which need options SMU K11 til SMU K20 does not work 4670 ARB tag clock rate precision too low 4708 List mode system hang up while editing via Insert Range 4713 Data list saving long lists via SCPI does not work correctly 4722 System crash while switching off incompatible modulations internally 4748 Generate Waveform File doesn t work if file exists already 4773 3GPP HSUPA Code Domain graphic E DPDCH displayed not correctly 4779 Release Notes for Firmware 1008 0329 52 28 R amp S SMU200A Information on the Current Version and History 3GPP uplink SCPI channel numbering wrong 1 sets channel 2 and so on 4794 1 29 Version 2 02 65 Released May 2006 New Functionality e Support of SMU B9 Baseband with ARB 128Msamples e Digital standard TD SCDMA with two options SMU K50 basic functions SMU K51 Enhanced BS MS test e Digital standard SMU K45 3GPP FDD HSUPA e Support of Win
44. properly working fixed 6434 Release Notes for Firmware 1008 0329 52 20 R amp S SMU200A Information on the Current Version and History EUTRA LTE Compatibility e All supported features are in line with the following official 3GPP specifications unless not revised by the according CRs listed below o TS36 211 v 8 2 0 o TS36 212 v 8 2 0 o TS36 213 v 8 2 0 e The following CRs are implemented o R1 081248 PRS sequence generation for downlink reference signal o R1 081518 Draft CR on Correction of the number of subcarriers in PUSCH transform precoding o R1 081520 Draft CR on Correction of PUCCH resource index for PUCCH format 2 o R1 081576 Correction of the number of subcarriers in PUSCH precoding o R1 081577 Correction of PHICH mapping o R1 081578 Correction of PUCCH resource index for PUCCH format 2 e The Downlink of this version of the SMx K55 is compatible with FSQ SW LTE K100 K101 K102 Version 2 2 BETA 3 General Features e Updated bandwidth definitions 1 4MHz and 3MHz previously supported by user defined settings e Support of User Filter user defined TX filter can be generated e g by means of R amp S FiltWiz and then uploaded to the SMx K55 Downlink e Full support of P SYNC S_SYNC and DL Reference Signal derived from CELL ID Supports channel coding for PDSCH Support channel coding for PBCH Supports scrambling for PDSCH and PBCH Full MIMO and Transmit Diversity support all precoding and CDD formats Support
45. se Offset was set to 0 after triggering fixed 5746 2x2MIMO Imbalance between both carriers due to correlation matrix fails fixed 6650 ARB Multi Segment Marker signal faulty with trigger mode Single Next Trigger fixed 6660 GPS Baseband B always triggered with baseband A fixed 6856 Custom Digital Modulation bits of data editor are hard to read fixed 6965 GPS critical database error occurred after loading setup fixed 7025 1 15 Version 2 05 104 56 Released Aug 2008 Fixed Issues Under rare conditions the guaranteed maximum level could not be reached fixed 6899 1 16 Version 2 05 104 54 Released Aug 2008 New Functionality e SMU B90 LO sync board for MIMO Modified Functionality e XM Radio frame counter implemented Fixed Issues Custom Digital modulation bit clock now used falling slope with external data and symbol clock 6627 GSM Instrument crashes using external retrigger mode fixed 6754 Remote control transfer fails if character Ox0A is in first block of binary data fixed 6783 BBIN selftest fails fixed 7695 Fading settings cannot be exchanged between SMU and AMU fixed 6804 Release Notes for Firmware 1008 0329 52 19 R amp S SMU200A Information on the Current Version and History 1 17 Version 2 05 104 33 Released July 2008 New Functionality e SMU K57 FM stereo e SMU K59 HSPA e Support of new synthesizer SSYN 1141 4220 Modified Functionality e Software update in o
46. sssssssssssssssossnsse 30 1 34 Version 1 S514 cscsssnsensescnsencsssnsensesensencsssnsensessnsensessnsensesensensecsnsensessnsensessnsensesensensessnse 32 1 35 Version 1 35 11S sscuissssssscescoscssssciscnsescvseniessnssssessbssdoassnssdoascbsadsaschssdsascboaboassussdsassasensessns 32 1 36 Version 1 35 10 scccccssssnccssssevssscnsenscstnsenscssnscnsenensensensnsensesensensensnennsesensensacsnssnsasensensessnss 32 1 37 Version 1 30 13 ssssssessnonnnsnnnsannnnnnnnnnnnnnn annn 33 1 38 Version 1 30 12 sccccssssscsessnsencsssnsensessnsenscssnsensesensenssssnsensesdnsensesensensecsnsensessnsensecensensessnes 34 1 39 Version 1 30 10 ononnnonionoononsenoneonescononecoronecconeonocnononnocncraonoccoroonoccoroorocnernosecncruoseonos 34 1 40 Version 1 20 34 viscicssssenssssssonsonssensensnsensensnsensonsnsensensnsensensnsensensnsensensnsensessnsensessnsensessnse 35 1 41 Version 1 20 33 conococcocnonccnonoononconconcnconconnononnoonnconnooneco cocoa cn noconeconocoe conoce co roconercanconecnss 35 1 42 Version 1 20 32 noococicnonononnonononcononcnnnnonononononcnronononnononcnronononnonononroronononor ono ronononon caos 35 1 43 Version 1 20 31 onocnncnocononnonononcnnoncnnanonononononcnnonononnononcnronononnonon cn rorononocnon cn roronononon caos 35 1 44 Version 1 20 17 EE E T E A T A T S 36 1 45 Version 1 10 10 onocncnonononnonononcononcnnoronononnononcnnonononconononronononoonononroronononor ono ronononon caros 37 1 46 Version 1 10 09 noocnnccoconinnononon
47. the device and switch it on again When the device is starting now you see the Bootmanager window blue background white field inside and a red selection line after a short time If you see this window press the cursor key 2 under the rotary knob select Backup Recovery and confirm this with pressing the key on the device or on the USB keyboard e After a short time the recovery and backup service ist started Make Backup Restore Backup Remove Backup Exit and Shutdown Select Make Backup __ via mouse or keyboard The menu disappears and the device shows you the versions of what will be stored Make Backup Make Backup Firmware and Software Platform Information Firmware Version 01 11 40 Software Platform Version 1 45 2 7 Make Backup Cancel Select Make Backup follow the instructions and the device starts working The backup process takes some minutes Please do not switch off the device otherwise your backup may be corrupt It s safe to switch off the device with the Exit and Shutdown __ button when the menu is shown again If you want to restore a previously saved version select Restore Backup in the Release Notes for Firmware 1008 0329 52 41 R amp S SMU200A Firmware Update same way 2 Install the new firmware version on the R amp S SMU200A e Switch off the instrument e Connect the external mouse and keyboard to the USB interface e Switch on the instr
48. ts for AWGN e g extended C N range e Selectable CRC order for BERT BLERT e Forced relearning of List in list mode e New filter for Custom Digital Modulation Pure Gauss e Selectable bandwith for external reference frequency Fixed Issues e SCPI instruction regarding 3GPP trigger output mode fixed SOUR BB W3GP TRIG OUTP2 MODE USER e GSM LevAtt timing was one symbol period too early fixed e 3GPP Trigger Marker panel path B fixed e Reduced breaks in output signal on frequency changes e SCPI Range of User correction was restricted fixed e Improved minus sign handling on level settings e List Mode Under some circumstances a list was received incomplete by SCPI fixed e Remote state inconsistent after GTL fixed e Limited range of TDMA trigger delay fixed Release Notes for Firmware 1008 0329 52 36 R amp S SMU200A Information on the Current Version and History 1 45 Version 1 10 10 Released June 2004 Fixed Issues e Timing problems with FPGA on SMU B10 fixed 1 46 Version 1 10 09 Released May 2004 Fixed Issues e Sometimes options are not correctly recognized fixed e Displaying of installed options is not correct with two SMU B10 fixed e System hang up when clicking in the graphic with right mouse button fixed 1 47 Version 1 10 08 Released May 2004 New Functionality e Support of 3GPP FDD including HSDPA with WinlQSIM Option SMU K20 e Support of overvoltage protection Options SMU B30 B32
49. udio source LFGEN 8695 Fading summation ratio adding both fader outputs based on peak 8688 instead RMS levels B90 problems with two path instruments with only one B2x below 200 8655 MHz LTE preset causes memory leak which may lead to crash 8565 eee Release Notes for Firmware 1008 0329 52 10 R amp S SMU200A Information on the Current Version and History 1 8 Version 2 10 111 116 Released May 2010 Modified Functionality Fading fading HST now available in MIMO2x2 Fixed Issues Multi segment info file creating file via SCPI results in empty MARKER 8264 tags and file is not loadable fixed Multi segment playlist several improvements WLanN Armed trigger not working in coupled mode fixed 8279 1xEVDO DL table not editable fixed 8280 GSM EDGE data and control list not selectable fixed 8286 Multi segment waveforms marker not considered fixed 8296 ARB Create Test Signal creates error message file not found fixed 8297 Fading Sometimes error message DSP don t get enough data fixed 8306 1 Q settings parameter Baseband Gain not in save recall fixed 8307 TETRA filter selection not correct and can cause a system hang up fixed 8341 Baseband connection test failed with fading type FineDelay30 8390 1xEVDO crest factor not reproduceable when switch state on fixed 8488 1xEVDO memory leak when switching state to off fixed 8493 1 9 Version 2 10 111 53 Released Feb 2010 New Functionality e SMU K68 Tetr
50. ument e Access Windows XP desktop Operating with the mouse e Wait until R amp S SMU firmware boot window with the progress bars appears e Click onthe Abort button in the boot window Booting of the instrument firmware is aborted and the Windows XP desktop is displayed Operation with the keyboard e Wait until R amp S instrument firmware has booted and the application has started e Press F4 to close the application The Windows XP desktop is displayed e Install new firmware version e Plug in the USB memory stick which contains the update file e Double click the item SMU200A_2 20 360 142 exe e Select Next Install and wait until installation has finished e Confirm that you want to reboot the instrument in order to activate the firmware update the instrument then restarts automatically the USB memory stick has to be removed 3 Execute Internal Adjustments e Press the key on the instrument front panel e Press the key select Internal Adjustments and execute Adjust All This process updates internal instrument adjustments and will take several minutes Adjustments requiring external measurement equipment are not affected by the firmware update and need not to be performed The firmware has been updated and the installation is completed eee Release Notes for Firmware 1008 0329 52 42 R amp S SMU200A Firmware Update 2 2 Remote Firmware Update 1 Install firmware gt Run SMU200A_2
51. with user coding Bugfixes Changes e Computationally expensive realtime signals e g RMC384 or H Set3 were sporadically shifted in time after retrigger fixed e Conflicts between H Sets and OCNS in the channel configuration are avoided now e When switching off the OCNS Mode the OCNS Channel state is switched off now in previous releases the channels were only converted to normal DPCHs but with state on e When generating H Set 6 the database was read out at the wrong positions fixed e HARQ Feedback Immediately after retrigger the packets were sent with random retransmission sequence number RSN fixed When changing from one RSN to another the last 1024 chips of the old packet were sent already with the new RSN fixed Wimax e CSTD Cyclic Delay Diversity Coupled Baseband Modes Baseband B is controlled from Baseband A for STC configurations Transmit Diversity with 4 antennas Band AMC modes for 2x3 AMC Band bitmap for sounding Additional user definable power boosting for each zone Time Plan displays inactive zones in grey Such as SISO zones on Antenna 1 Multiple PDUs per burst DCD and UCD added for OFMD mode UL MAP and DL MAP in one burst for OFDM mode eee ee tal Release Notes for Firmware 1008 0329 52 22 R amp S SMU200A Information on the Current Version and History 1 18 Version 2 04 303 32 Released April 2008 Fixed Issues Sometimes the device does not shut down correctly fixed 6424
Download Pdf Manuals
Related Search