ADSL Router
Contents
1. Default Configuration for New Zealand This Router is shipped with the following factory default settings Router IP address 192 168 1 1 Subnet mask 255 255 255 0 VPI o do not change VCI 100 do not change Encapsulation PPPoA VC MUX do not change NAT enabled do not change DSL line mode auto WAN IP dynamic DHCP enabled UPnP IGD disabled Security Firewall off Intrusion Detection disabled Router configuration amp management Administrative User name admin Administrative Password admin Telnet password admin Users must not change the VPI VCI Encapsulation or NAT settings DSL line mode can be set to either auto or G dmt Advanced users who have other setup preferences should refer to the User s Manual Before you start Make sure your computer has the following installed An Ethernet or USB port see Choose your connection option below TCP IP protocol Aweb browser Internet Explorer 5 0 Netscape 6 or better Obtain the following information from your ISP Login user name and password Public IP address Note only required if you purchase a Static IP DNS server IP address if specified by ISP Choose your connection option Ethernet for a standalone computer Connect using the enclosed straight through Ethernet cable ge Dynalink Ethernet via a network hub to a LAN Connect using the enclosed straight through Ethernet cable to the UPLINK port of the netwo2. ge ADSL Router Quick Setup Guide RTA22 ge Dynalink Important This Guide is intended to get you started quickly The factory default profile of this Router is customised for New Zealand users Please follow through the steps we describe here to install and set up your Router This Guide should be read in conjunction with the RTA220 Series ADSL Router User s Manual This is provided as a PDF file on CD You can return to the previous menu click on the View User Manual button to view or print For the remainder of this Quick Set Up Guide all references to the Users Manual refer to this PDF file Note The User s Manual was written for international users New Zealand users should skip most sections of Chapter 3 except PPPoA NAT mode PPPoA NAT is the only connect mode currently supported in New Zealand Advanced users who have other setup preferences should refer to the User s Manual There is a table in Section 8 of this Guide to assist you in locating the relevant material Important Safety Notes can be found on page III of the User s Manual Contents inside this box RTA220 ADSL Router Power adapter 12VDC 1A ADSL line cord for New Zealand RJ 45 Ethernet cable straight through cable USB cable Driver amp Utility CDROM User s Manual included If you connect via Ethernet port instead of USB port there is no driver to load ADSL Router Quick Set up Guide
3. Data going through USB port On USB link is ok DSL Link Status Off Handshaking training in progress Blinking Data going through ADSL port On ADSL link is up 10 ge Dynalink Troubleshooting Q1 Cannot open the Router control panel from my browser 1 Check that the Router s LAN or USB light is on If not check your Ethernet or USB cable If you connect via Ethernet check that the Ethernet cable we supplied is plugged directly into a stand alone computer OR the uplink port of network hub Should the cable be plugged into any other port on a hub a crossover or uplink cable must be used A crossover cable is not provided with the Router If you assign IP addresses manually check that every IP on the LAN is unique The Router s private IP is 192 168 1 1 by default You must use this address or the address you have changed it to in order to access the Router s control panel If your computer obtains an IP address from the Router follow this procedure to make sure your computer s IP address is renewed Windows 95 98 ME 1 Go to Start Run Type winipcfg in the dialog box and click OK 2 When the IP configuration screen appears click Release and then Renew Windows NT4 2000 XP 1 Go to Start Run Type cmd in the dialog box and click OK 2 At the command prompt type ipconfig to display IP information from DHCP server 3 Type ipconfig release and then type ipconfig renew Per
4. security level allows more types of traffic to pass through e g no ICQ traffic is allowed in or out at security level Medium however the Router will allow outgoing ICQ traffic at security level Low To enable the firewall go to Configuration Security Firewall Select the level of security you require Click Apply and save configuration using the System Save Configuration menu Advanced users may want to customise the default firewall policies to meet their particular needs Please refer to page 57 of the User s Manual eL wew all Policies Mic 10s oft Inten HME at IE mina Pop sd by P C iz The deault policies for vanous security levels are applied as below Other application services which are not listed here are blocked if the firewall is enabled HTTP o No C ons s No C Fep an no e ae ere ae 25 No Yee No ve No wo Portes 110 No Yes No Yes No No eee ie eae eee Real iohideo tep 7070 7071 No Yee No No No No jo ideot wep PETAD vi eo Mee He is ia ten 1735 fre vo No ft Backup the Router configuration ge Dynalink It is desirable to keep copies of your configuration on disk The Router can read from a saved configuration file and restore your customised configuration after events such as a reset to factory defaults To backup or restore your Router s configuration go to System Quick Configuration Guide to the Users Manual Ref
5. Click Connect r Control Panel Quick Start lt Quick Start 0 100 PPPoA VC MUX System C Status PPP connection status UserNeme i Password C Configuration The Router will now connect to your ISP At any time in the future if you wish to check that the Router is on line go to Quick Start A screen similar to the following image confirms that you are on line It shows the public IP address assigned by your ISP and the time the Router has been on line Click Disconnect only if you wish to interrupt the connection aa oe Router Control Panel ae Quick Start C Status Configuration DSL Line status Show Time Your IP assigned by ISP Running Profiles balsa VPUVCI Data Enc NAT Local Local WAN IP Ihe On Lit ine yy ime fie rma vemozloaseal aomas moooi IE Please select the pre defined profile for your router PPPoA Router v Apply and Save If you cannot get online refer to Q2 in Section 10 Troubleshooting g Dynalink STEP 3 SAVING USERNAME amp PASSWORD INFORMATION If you want to save your Internet account user name amp password into the Router go to System Save Configuration in the Router menu Enter the Router s administrative user name and password if required to proceed By default the Router administrative user name and password are both admin Click Save Wait for confirmation From here the Router s basic configuration is compl
6. aviomabcally if your network supports oe ee Click OK to finish Ss ttc ore Use the folloveng DNS server adderar You have now finished configuring your computer Going On line This requires only 3 simple steps Prefened ONS perver Abemate DHS server STEP1 GO TO THE ROUTER S QUICK START PAGE 7S cere hy edrnanishishor fet 192 168 1 2 255 255 a8 D 1 18 11 Start your web browser Enter the address http 192 168 1 1 Enter user name and password if required to proceed By default the username is admin and the password is admin You will see the Quick Start page of the Router Refer to Q1 in Section 10 Troubleshooting if you cannot get this screen Quick Start System E Status Configuration Quick Start DSL Line status Running Profiles ypuvcil DataEncap NAT II PIA PICI Data Encap NA T Loi r Control Panel AN I P On Line Tir ne Refresh Action Foie evn vewuxfeaocne os Please select the pre defined profile for your router PPPoA Router v Apply and Save ADSL Router Quick Set up Guide STEP 2 ENTER INTERNET ACCOUNT DETAILS First check on the front panel of the Router that the DSL light has turned solid indicating the link is up Click the Connect button Do not click Apply amp Save as this button is intended for changing the pre defined profile Enter your Internet account User Name amp Password
7. e IP Primary Network Logon address assigned to your k TCP IP Properties 21x computer Subnet Mask is ao kee a 255 255 255 0 Gateway WINS Configuration IP Address An IP addr be all his c Select the Gateway tab Enter the a a 9 administrator t Router s IP address 192 168 1 1 and r eae rera on acters tee oa click Add Click OK amp then OK to finish You BRE a E aee aoaea e fe i IP address may be prompted for the Windows Se CD and then be asked to restart lP Address 192 168 1 2 Answer Yes to restart the Subnet Hak computer E CPAP Properties Bindings Advanced Nemos DNS Configuration Gateway WINS Configuration IP Address first ean bei Pea De ne Eo The ads cnet be 2 the onder in which these Neve gateveay 197 168 1 1 Add For Windows 2000 XP From Control Panel double click Network Connections Open Local Area Connections and click Properties Double click Internet Protocol TCP IP Select Use the following IP address Enter 192 168 1 x x iS any number Internet Protocol 1CPIP Properties between 2 and 254 This is the IP address assigned to your cng computer Subnet Mask is 255 255 255 0 O Obtain an IP addiess automaticaly l E Ure tha lalovang IP actress Enter the Router s IP 192 168 1 1 Pastes as the Default gateway and Subnstma Preferred DNS server Defaut gatava g Dynalink IP sethings acngned
8. er to these page numbers of the Users Manual on the enclosed CD for USB DRIVER INSTALLATION Windows 98 4 Windows ME 6 Windows 2000 8 Windows XP 10 CONFIGURATION Setting up TCPAP on a client PC Windows 98 25 Windows ME 29 Windows NT 29 Windows 2000 33 Windows XP 35 Configuring a PC to get an IP address from a DHCP server Windows 98 36 Windows ME 37 Windows NT 37 Windows 2000 a7 Windows XP 38 WEB BASED ROUTER CONFIGURATION MENU Using Web Based Manager 41 Quick Start 42 System Device Information 43 Administrative Security 43 Quick Configuration 44 Save Configuration 45 Upgrade Software 45 Reset Router 46 Status DSL Connection 46 WAN Connection 47 Traffic Counter 47 Routing Table 47 DHCP Table 48 Configuration DSL Configuration 49 LAN Configuration 50 WAN Configuration 52 IP Route 54 DNS 55 Security 57 Virtual Server 61 UPnP 63 ADSL Router Quick Set up Guide Indicator lights There are five indicators on the Router s front panel Every time the Router is powered on or reset all the lights will come on indicating the self test is in progress Indicator Function Description PWR Power Off No power On Power is on DIAG Diagnosis Off Self test OK Blinking System updating On Self test or system failure LAN Ethernet Link Off Ethernet link not present Blinking Data going through Ethernet port On Ethernet link is ok USB USB Link Off USB link not present Blinking
9. eted AL Router Control Panel Quick Start Save Configuration E System Device Inf A rir ZACH This page allows you to save all current configuration settings to non volatile memory Please wait for several seconds to complete this process WARNING DO NOT turn off your router during saving configuration f S E Configuration Note If you manually assigned a fixed IP address to your computer or you have another DHCP server already on your LAN disable the DHCP server on your ADSL Router Refer to LAN Configuration DHCP server on Page 50 of the Users Manual ADSL Router Quick Set up Guide Important tips for security In order to benefit from the security features of this Router Do Change your Router s administrative user name amp password Enable firewall security on the Router Back up your Router s configuration Don t Enable remote access to the Router unless you know how to handle security Send your Router away for repair or replacement without resetting to factory default or wiping out your Internet account login details To change the Router s administrative user name amp password go to System Administrative Security Select a user name and password you will not forget Firewall security It is recommended that the firewall be enabled There are four preset levels of security Low Medium High amp Block At the Block level nothing passes through Reducing the
10. form a PING test Go to Start Programs MS DOS or Command Prompt In WinXP 2000 NT4 click Start Run Enter cmd then OK Type ping 192 168 1 1 then press Enter Pinging 192 168 1 1 with 32 bytes of data Reply from 192 168 1 1 bytes 32 time 4ms TTL 30 If you see a similar response the Router is communicating with the network correctly and the problem lies elsewhere If the result is Request timed out or a Similar failure there is a TCP IP networking problem Check the LAN cable type is correct as in step 1 above and firmly plugged in To check a computer s network settings see Step 2 Section 4 Configure your computer Disable any personal firewall or virus checking software temporarily If you are using Internet Explorer go to Tools Internet options Security Reset the security level of all 4 icons to default You can revert to your customised settings after configuring the Router ADSL Router Quick Set up Guide 5 Q2 If previously you were using a dialup modem check the browser configuration For example in Internet Explorer go to Tools Internet options Connections and select Never dial a connection Also check LAN Settings that the option Use a Proxy Server is not selected Ifthe Router is connected to a network hub try connecting the Router directly to the computer in a standalone setup to eliminate any possible hub problems If the LAN already has a DHCP server enabled disable it Refer to the sec
11. free of charge provided it is returned to us with proof of purchase from an authorised dealer within the warranty period Return delivery after repair will be paid for by Dynalink Modems Ltd within New Zealand We reserve the right not to repair or replace goods that have been mishandled abused or not installed according to the guidelines as outlined in the instructions have been subjected to a power surge from other equipment or other external factors have been altered or modified ge Dynalink Always check that your hardware is installed correctly Check our web site for the latest information and troubleshooting guide If you have difficulties contact Dynalink Technical Support for issues relating to router installation and operation Phone 0800 653 962 Mon Fri 8 30am 7 30pm Fax 0800 503 962 Ak Email support dynalink co nz as E DE Web www dynalink co nz NZRTA220QG 01
12. nfiguration in the User s Manual The description below assumes you are connecting via an Ethernet port By default the DHCP server on your ADSL Router is enabled The simplest configuration method is to follow option 1 below STEP1 OBTAIN AN IP ADDRESS FROM THE ADSL ROUTER You do not need to specify an IP address when configuring TCP IP properties If your computer stands alone and is set up to obtain an IP address automatically you can move on to Section 5 Going On Line ADSL Router Quick Set up Guide STEP 2 MANUALLY ASSIGN A FIXED IP ADDRESS TO YOUR COMPUTER If you prefer to assign an IP address manually use 192 168 1 x x is any number between 2 and 254 and subnet mask 255 255 255 0 Specify the gateway as 192 168 1 1 and enter DNS server IP as 192 168 1 1 Windows Specific instructions follow i Network 24 xX Windows 95 98 ME Configuration Identification Access Conta From Control Panel double click The following network components are installed Dial Up Adapter Realtek RTL8029 4S PCI Ethernet NIC NetBEUI gt Realtek RTL8029 4S PCI Ethernet NIC y TCPAIP gt Dial Up Adapter Y TCP IP gt Realtek RTL8029 A5 PCI Ethernet NIC File and printer sharing for Microsoft Networks Network Scroll down and highlight TCP IP your network card Click Properties Select the IP Address tab Enter 192 168 1 x x is any number Remove Properties between 2 and 254 This is th
13. ond paragraph of Section 4 Configure your computer in the User s Manual Cannot connect to the Internet or cannot browse Check that Router s DSL light is on Normally it takes less than one minute to establish an ADSL link A link will establish as long as there is sufficient signal If the DSL light does not come on the Router is not detecting any signal Check that e The ADSL service has been enabled e The Router is connected to the correct jackpoint e The Router is connected directly to a jackpoint not after a filter or other device Check that Router is on line Bring up the Quick Start menu of the ADSL Router Control Panel Refer to Step 2 Enter Internet account details of Section 5 Going On Line f NAT IP shows 0 0 0 0 you are not on line Make sure the correct user name and password are entered The username and password are provided by your ISP Check the configuration of your computer and Router If you still cannot browse perform a PING test as described in Q1 3 using these addresses A Ping www dynalink co nz or any valid web address B Ping 205 178 180 16 or any valid public IP address If both A amp B returned no reply go to Quick Start and check that NAT is enabled Also make sure the Router s firewall is not set to Block If these settings are correct ping the computer s IP address e g ping 192 168 1 2 If there is still no reply your network card may be faulty If A ret
14. rk hub If the hub does not have an UPLINK port connect using a cross over Ethernet cable to any other port of the network hub Cross over Ethernet cable is not provided USB for standalone Windows 98 ME 2000 XP computers Connecting the Router via Ethernet is the preferred option However if you decide to connect via the USB port you must install the USB drivers for this Router The drivers are found on the enclosed CDROM Please refer to Chapter 2 Installation on the User s Manual for step by step instructions Connect the ADSL Router Connect the 12V 1A DC power adapter to the PWR jack of the Router and plug the adapter into a mains power outlet Switch on the Router Connect the DSL port of the Router to your ADSL jackpoint telephone wall socket with the enclosed phone line cord Never connect the ADSL Router through a Microfilter Connect the LAN port of the Router to the Ethernet port of your computer or uplink port of a network hub using the Ethernet cable provided If you have chosen to connect via the USB port connect the USB port of the Router to the USB port of your computer or USB hub using the USB cable provided After connecting the cable LAN or USB the corresponding light on the front panel of the Router will turn on If not it indicates a problem with the Ethernet or USB connection Refer to Section 10 Troubleshooting Configure your computer For a step by step guide refer to Chapter 4 Co
15. urned no reply but B showed a reply this is probably a DNS problem Check that you have entered the correct DNS address if this is required by your ISP If both A amp B showed a reply it could be a problem with your browser settings Try returning any custom settings of the browser to default If you have personal firewall software running disable it Check if the condition in Q1 5 applies Finally shut down the computer and restart it ge Dynalink Q3 Browsing is fine but I cannot run certain applications such as ICQ Check that your firewall security setting is not too high Try temporarily disabling the firewall If the application now runs you can either lower the security level setting or tailor your firewall settings to allow traffic of the application through Q4 My customised Router administrative password has been forgotten and the Router control panel is no longer accessible Restore the Router to factory defaults A hidden reset button is located next to the power on off button at the back Using a suitable size pin while the Router is powered on press the reset button for several seconds and release All the front panel lights should come on indicating a successful reset ish baiihe ge Dynalink Dynalink Modems Ltd warrants this product against defects in materials and workmanship for a period of twelve months from the original date of purchase We will at our discretion repair or replace the faulty unit
Download Pdf Manuals
Related Search