Owner`s Guide
Contents
1. STEP 2 Release both transmitter buttons Press and release the SCROLL button to select desired cor rection setting The transmitter display will show corre sponding number with each button push Settings 1 Extra Light 2 Light 3 Medium 4 High 5 Progressive STEP 3 Hold the pet fence collar receiver against the wall mount transmitter The collar receiver light will illuminate and is ready to be programmed Press and Owner s Guide PCC 100 amp PCC 200 release the bottom button marked SET on the wall transmitter The collar receiver light will flash the number corresponding to the level you have selected When programming is complete the transmitter will return auto matically to normal operation Radio Frequency Programming This programming option allows the user to switch the operating frequency from 7 KHz to 10 KHz in the unlikely case of signal interference from sources such as neighboring pet fencing systems Your system has come preset from the factory on 7 KHz where you are most likely not to encounter interference issues To change your frequency settings STEP 1 Press and hold both the top and bottom but tons marked SCROLL and SET on the wall transmitter simultaneously for 6 seconds The transmitter display will first show 00 for after three seconds continue to press both buttons for an an other 3 seconds to enter frequency mode Either 012. NOTE This equipment has been tested and found to comply with the limits for a Class B digital devise pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur ina particular installation If this equipment does cause harmful interference to radio or televi sion reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e reorient or relocate the receiving antenna e increase the separation between the equipment and the receiver e connect equipment to an outlet or a circuit different from that to which the receiver is connected e consult the dealer or an experienced radio TV technician for help Caution Changes or modifications to any component not expressly approved by Perim eter Technologies Inc could void the user s authority to operate this equipment Owner s Guide PCC 100 amp PCC 200 Perimeter Comfort Contact ea Huotoctes Pet Fencing System Safer by design Transmitter 500 ft long fence wire AC Adapter A Wire Splices Collar
3. or 02 will be displayed on the wall mount transmitter STEP 2 Release both transmitter buttons Press and release the SCROLL button to select de sired frequency settings The transmitter display will show corresponding number with each button push Settings 01 7 KHz 02 10 KHz STEP 3 Hold the pet fence collar receiver against the wall mount transmitter The collar receiver light will illuminate and is ready to be programmed Press and release the button marked SET on the wall transmitter The collar receiver light will flash the number corresponding to the level you have selected When programming is complete the transmitter will return auto matically to normal operation Owner s Guide PCC 100 amp PCC 200 STEP 7 Training your pet Please take your time training your dog and complete each step of the process to enjoy optimal performance from your system If you have questions along the way expert advise is only a call away 1 866 900 2007 The goal of fence training is to help you teach your dog to identify and respect her new fence to make the training fair so your dog will understand the consequenc es of leaving and to make the training fun so your dog will enjoy staying and playing on your property Completely trusting your dog with his Perimeter Fence will take place over the course of about 3 weeks The training is a small part of the three weeks the res
4. active state is NOT THE STRENGTH OF CORRECTION OR COLLAR OUTPUT This number represents the signal field area The signal field setting determines the total correction area or how far your dog s fencing collar will activate from the fenc ing wire Your system comes preset from the factory on setting 10 which is 10 total feet or 5 feet from the fence wire You can adjust your system easily by pressing the top or bottom transmitter buttons to select a setting between 1 and 32 EXAMPLE Setting Total Signal Distance Area From Wire 10 10 ft 5 ft 14 14 ft 7 ft 20 20 ft 10 ft All Comfort Contact Pet Fencing Systems come fully programmed from the factory ready to use however the Ultra Comfort Contact PCC 200 has two optional pro gramming functions Correction Level Programming model PCC 200 only Perimeter Pet Fencing Systems come factory preset with an automatic adjusting level of correction from low to high de pending on your pet s speed and proximity to the boundary wire The Ultra Comfort Contact system can be programmed to any one of 5 different output levels from Extra Light to Extra high depending on your dog s personality and temperament To change the system correction levels STEP 1 Press and hold both the top and bottom but tons marked SCROLL and SET on the wall transmitter simultaneously for 3 seconds The transmitter display will show 00 indicating programming mode
5. is performing properly 4 Testing your system Before burying your boundary wire Test your fence using your pet s training collar in multiple locations in and around the yard Owner s Guide PCC 100 amp PCC 200 Your new Pet Fencing System AT A GLANCE 5 System Adjustments Programming Options The Perimeter Ultra Comfort Contact System PCC 200 can be programmed for up to five different stimulation levels and two different frequency settings by following the easy programming steps see page 9 for reference 6 Bury fence wire The fence wire that dictates your pet s boundaries is buried 1 3 under the ground You can use a flat edge spade gas powered edger or there may be Pet Stop Professional installation help avail able in your area 7 Training your pet Training your pet to her new fence will take approximately two weeks with most of the time spent closely watching your pet to ensure compliance to the fencing system Owner s Guide PCC 100 amp PCC 200 STEP 1 Planning your fence layout e When designing your fence layout it is important to remember that your fence boundary is one continuous loop of wire starting at your wall mount trans mitter forming a boundary loop around your selected area and returning back to the transmitter Entire Yard e You will need to allow room in your plan for 8 10 of signal area from the boundary wire e Do not run the boundary w
6. Bound Em oundary e Flags vv Av Installation DVD Congratulations You have purchased the most comfortable and reliable pet fencing system for your cherished family pet Perimeter Technologies Comfort Contact system was designed by the industry s most experienced team to provide years of worry free freedom for both you and your pet Simply follow the steps outlined in this user s guide and your fence will be operational in no time Should you have any difficulty along the way help is available both by calling the Customer Care Center at 1 866 900 2007 or by talking to a local Pet Stop Fencing Professional www buyperimeter com Owner s Guide PCC 100 amp PCC 200 Your new Pet Fencing System ATA GLANCE 1 Determine the layout of your fence The Comfort Contact Pet Fencing System is completely customizable to any shape of property and can be used to keep your pet away from off limits areas such as gardens or pools See page 4 for sample layouts Be sure to call your local utility companies to mark underground cables before you dig 2 Select a transmitter location The wall mount transmitter is your pet s fence control center The transmitter sends a digitally encoded radio signal through the fence wire The transmitter needs to be located in a dry indoors area such as a garage or utility room 3 Layout your fence wire Always lay your fence wire on top of the ground before burying to ensure the fence
7. Perimeter Comfort Contact ea Huatoctes Pet Fencing System Safer by design Owner s Guide PCC 100 amp PCC 200 Owner s Guide PCC 100 amp PCC 200 IMPORTANT YOUR PERIMETER PET FENCING SYSTEM COMES WITH ADDITIONAL RUBBER TIPS FOR YOUR PET S COMFORT CONTACTS THE COMFORT CONTACTS WILL LOSE CONDUC TIVITY OVER TIME AND NEED TO BE CHANGED TO MAINTAIN THE PERFORMANCE OF YOUR FENCING COLLAR IF USING THE RUBBER COMFORT CONTACTS PLEASE CHANGE RUBBER TIPS WITH EACH COLLAR BATTERY CHANGE ADDITIONAL RUBBER TIPS CAN BE PURCHASED AT www buyperimeter com e Any tight collar or consistent pressure on the skin can cause a condition known as Pressure Necrosis bed sores which if left untreated can be severe To help reduce the likelihood of pressure necrosis please do the following Remove the pets training collar every 12 hours Look for any skin irritation and discon tinue product use until healed Wash pet s neck and collar frequently with warm soap and water Do not attempt to wash the pet s training collar in washing machine or dish washer e No containment method is full proof and your Perimeter Pet Fencing System is not a substitute for responsible pet ownership and close supervision of your pet Do not use this product when away from home e Never use this product if you believe your pet poses any danger to people other ani mals or itself e Keep your dog safely contained and on a leash during the training process
8. are not respected For the next lesson you will need to remove the post covers from the training collar contacts With your dog still on a lead walk to the boundary with your dog Have a helper walk on the outside of the fence area The helper should ignore your dog and never coax the dog out of the fenced area Your dog will most likely forget earlier les sons and attempt to leave the safe area The moment your dog reacts to the fence correction immediately retreat to the safe part of the yard and lavish your dog with praise Please note it is very important that your helper not stop look back or acknowledge the dog in any way Continue this lesson at a number of differ ent areas around the boundary Owner s Guide PCC 100 amp PCC 200 Should your dog not appear to have felt the collar cor rection check to ensure the collar is making contact with the skin It may be necessary to use one of the longer metal contacts provided for dogs with a dense coat LESSON 3 Distractions If your dog is avoiding the boundary at multiple locations around your boundary you are ready to add more tempting dis tractions Remember never pull or coax your dog into the boundary area This lesson teaches your dog that he must resist all temptations to leave the yard You can t assume that if your dog won t chase a ball out of the yard He won t chase a bicycle Or favorite
9. em before you bury the wire This is a real time saver should you encounter a problem with your installation 1 Measure the amount of distance from your wall mount trans mitter to the beginning of your boundary loop at the edge of your yard You will need to run two lengths of wire twisted together to the start of your boundary loop Twisting the wire together cancels the radio signal and allows your pet to safely cross over 2 Taking your two equal lengths of wire secure two ends to something stable and pull tout on the other ends Twist the two pairs of wire 2 together until se there are 8 ao 12 twists Ps Twisted Wire per inch Itis 77 To Transmitter much faster to secure two of the ends in a drill and the drill will do the twisting for you Owner s Guide PCC 100 amp PCC 200 3 Starting at the end of your twisted wire run your single strand of wire around your property as you have designed ending back again at the end of your twisted wire Boundary Loop Twist one end of your bound Ta Tra istiden lt ary loop to oneendofthe FA twisted wire T with a wire Splice nut Repeat with the remaining loose ends Using the waterproof splices push each wire nut as far down into the gel as possible and secure lid Check to ensure that there are only two wires for each splice used PLEASE NOTE Using just wire nuts or electrical tape will not keep moisture from in
10. he supplied post cov ers that are included with your Perimeter Fence This is to ensure that your dog can hear the warning tone at the boundary but there is no chance of correction The post covers will be removed in phase 2 of the training Put the electronic training collar on your dog and make sure the wall mount transmitter is turned on The first lesson is to introduce your dog to the boundary and to help her understand to back away from the fence when the warning tone is heard With your dog on a lead casually walk to the boundary When the dog reaches the signal field and hears the warning beep immediately spin around and briskly jog back into the yard The dog will feel the tug and run after you Praise enthusiasti cally On days two and three repeat the same lesson in different part of the yard As the training sessions of the next three days progress you ll see that your dog will start to anticipate the signal and retreat without your prompting Day three is successful if your dog retreats without your prompting and refuses to approach the boundary as you approach For each successful attempt be sure to praise praise and praise again LESSON 2 Respect the Fence Although your dog is learning fast and avoiding the boundary he will forget or attempt to break the rules with an interesting distraction beyond your yard To prevent this your dog must experience what happens if the fence boundaries
11. ire within 10 parallel of utility lines Utility lines can create interference Have utility lines marked prior to fence wire installation e To maintain a consistent signal field use a gradual radius when running the wire around corners as illustrated Avoid hard 90 degree angles Around Obstacles Back Yard Only Separate Front amp Back Owner s Guide PCC 100 amp PCC 200 STEP 2 Selecting a transmitter location e Select a location to hang your system transmitter that is dry and indoors with a standard 110VAC electrical outlet nearby A location in the garage or util ity room is usually ideal e When selecting a location keep in mind that the fence system wire will run from your transmitter to the wire boundary outdoors This can be done through a window or by drilling a 3 8th inch hole at the base of the wall for the wire to pass through Remove the transmitter housing cover by pressing your thumb on the bottom of the cover and lifting off When removed hold the base of the transmitter housing against the wall in the chosen location and mark the location of the screw holes with a pencil Use the supplied mounting hardware and hang transmitter on the wall Replace the transmitter housing cover by placing the cover tabs in base and pushing bottom housing down STEP 3 Layout your fence amp wire connections It is important to layout your boundary wire and test your fencing syst
12. neighbor Your training has been successful at this point if your dog has resisted the urge to cross the boundary on lead with any distraction you can dream up LESSON 4 Off Lead With Supervision After several sessions of distractions your dog should be ready for off lead play You must stay in the yard for off lead training The more your dog stays on the property for the first month the less chance of your dog ever attempting to leave the area Continue to supervise and play with your dog outside for a period of one week Should your dog bolt out of the property for any reason during this phase retrace your training your last training steps with distractions with your dog on a leash LESSON 5 Off Lead Unsupervised When your dog resists all manner of dis tractions both on and off the lead he can be left unattended in the yard Keep a close eye on your dog for two weeks from inside the house This freedom should be brief at first and the amount of time increased gradually Before and after each unsupervised session you must continue the play and praise routine to reinforce that the yard is a happy fun and safe place to be Owner s Guide PCC 100 amp PCC 200 LESSON 6 Removing the Flags After two weeks of successful contain ment you can begin removing the flags Start by removing every other flag every other day until all of the flags are gone The leads trainers flags and the elec tronic
13. r expansion due to heating and cooling e Itis helpful to water your lawn after installation and again walk over the trenched areas to further secure the wire underground You may encounter some obstacles that will need to be crossed during your instal lation e When crossing a concrete driveway clean out an expansion joint with a screwdriver push wire into the slot and cover with a clear silicone caulk e Itis necessary to cut a trench in asphalt driveways with a circular saw and masonry blade Place wire in trench and cover with asphalt sealant e The wire can be run through PVC tubing or garden hose and left on top of the ground when crossing heavily wooded rock areas or when crossing creeks or streams The PVC or garden hose will not obstruct the fence radio signal e Itis not recommended that you leave the wire above ground unprotected due to damage by weather and wild animals Test the system again as described in step 4 This time test the fence at intervals of 10 feet and when you hear the warning beep place one of the supplied boundary yard flags The boundary flags will be a visual training aide for your pet during the training process The flags will be gradually re moved after the two week training period Owner s Guide PCC 100 amp PCC 200 STEP 6 System adjustments and programming Adjusting the Signal Field Width PLEASE NOTE The number displayed on your wall mount transmitter in its normal
14. t of the time is just close supervision Time should be set aside to work with your dog for 10 15 minutes two times per day Both you and your dog will appreciate short fun lessons and make the training more effective There are six phases to the training lessons LESSON 1 Back away from the fence 6 Sessions LESSON 2 Respect the Fence 1 Session LESSON 3 Adding interesting distractions 8 Sessions LESSON 4 Off Lead With Supervision 1 Week LESSON 5 Off Lead Unsupervised 2 Weeks LESSON 6 Flag Removal Every other day until gone e Use a calendar so you can keep track of the training process Your dog s behavior will tell you when it is time to proceed to the next level e A training session includes putting the Perimeter training collar on your dog making sure that the collar has the proper fit high on the dog s neck and the collar is making contact with the skin e Start every session playing with a favorite toy and plenty of praise Make sure your dog is comfortable and hav ing fun e Do boundary work at locations around the entire boundary of your yard e Always end sessions with your dog successfully avoiding the fence and with more play and praise e If you are training more than one dog train each dog in separate training ses sions Owner s Guide PCC 100 amp PCC 200 LESSON 1 Back Away From the Fence Start the first phase of train ing with the collar contacts covered with t
15. t opening Replace the battery cap 2 Ensure that the fence wires are properly inserted into the wall mount transmitter and the adapter is plugged into the side of the transmitter and wall outlet The transmitter display should illuminate 3 Hold the pet s training collar by the nylon strap as shown at approximately the height of your pet s neck 4 Slowly approach your outside boundary loop wire and listen carefully for the warning beeps Should you hear the warning beeps back up and try different parts of the boundary area ensuring that the collar is activating properly in other locations If the collar activates too far or too near the fence wire adjust the signal field setting see STEP 6 5 Walk back and forth over the twisted wire listening for any warning beeps There should be none 6 Walk around the safe areas of the yard and house listening for any warn ing beeps Again there should be no response from the pet s collar when further than 10 from the boundary loop TROUBLESHOOTING TIPS The collar will not activate at the bound ary loop e The training collar s battery has been installed in the proper orientation and the cap has been secured e The wall mount transmitter has the wire that runs from the outside loop secured in the wire connectors and the trans mitter is plugged in to the wall outlet e The boundary loop is connected to the twisted wire running to your transmitter
16. terfering with your system s performance Use the supplied gel filled splice housings Insert the other ends of your twisted wire in the wall mount transmitter as shown Tighten screw terminals taking care not to over tighten 6 It is recommended that you ground your transmitter Connect the ground terminal center screw wire connec tion on the transmitter to a ground rod via electrical wire located outside of the house with ground rod material and depth as recommended by National Electrical Code The alternative way is to connect the ground terminal on the transmitter to the center screw on the AC outlet via electrical wire center screw is ground The outlet used must be grounded to be effective An experienced pet fence dealer tv technician or electrician can help should you have concerns regarding the proper grounding of this equipment Owner s Guide PCC 100 amp PCC 200 STEP 4 Testing your fence operation It is important to test that your system is functioning properly before burying the boundary wire You will be looking to en sure that the fence is activating properly at the boundary locations as well as look ing for unwanted signals in the house and other safe areas of the home 1 Install the supplied battery in your pet s training collar Remove the battery cover screw cap insert the battery and ensure that the top marked This end up is closest to the battery compart men
17. training collar are all clues for your dog to learn the boundaries They are all removed gradually except the electronic training collar It s essential that you observe whether you re off lead unsupervised dog still avoids and retreats from the unmarked boundary If your dog s response is anything but immediate retrace your steps through the training process Thank you for choosing Perimeter Pet Fencing Systems Owner s Guide PCC 100 amp PCC 200 TRAINING AND INSTALLATION NOTES Owner s Guide PCC 100 amp PCC 200 TRAINING AND INSTALLATION NOTES LIMITED LIFETIME WARRANTY Call Customer Care First We Can Help 1 866 900 2007 Perimeter TechnologiesQ Inc warrants that its products to the original retail purchaser will be free from defects in material and workmanship under normal use for a period of one year from the date of the original retail purchase at no cost Shipping to repair center not included This coverage does not include accidental damage or misuse After one year from date of original consumer purchase Perimeter will at our option repair replace or upgrade the defective component at a fixed rate based on the component for the life of the original owner Owner must provide proof of purchase Cost of shipping is not covered under the limited lifetime warranty Some shipping charges may apply Perimeter Technologies offers a hassle free replacement program Simply call 1 866 900 2007 and let us help you
18. using the supplied waterproof splices and that there is only TWO ends of wire inserted into each splice e Check to determine if your pet fence system is installed in close proximity to a neighboring system If so see STEP 6 System Adjustments and Programming e Should you continue to encounter dif ficulties please call customer care at 1 866 900 2007 The collar activates in safe areas of the yard or home e Check that the wire is not running close to outside utility lines and move where necessary Owner s Guide PCC 100 amp PCC 200 e Move the boundary loop away from large metal objects such as outdoor sheds or metal fences e Move the boundary wire away from the side of the house e Turn the signal strength down on the wall mount transmitter See STEP 6 System Adjustments and Programming STEP 5 Burying the fence wire After you have the fence wire positioned on the top of the ground and are satisfied that the fence is functioning properly it is time to bury the wire e Starting where the wire exits your home Use a flat edge spade or gas powered edger to cut a 1 3 trench at a 45 degree angle A trench cut on an angle will keep the wire secure when put in the ground and will heal faster e After completing the trenching around your boundary loop insert the wire in the trench and step down to secure the wire in the ground Do not pull the wire tight in the trench leaving some slack fo
19. with your problem Please do not return this product to your retailer Perimeter Technologies Inc Perimeter 1 866 900 2007 Q Oo REA www buyperimeter com Safer by design i i 2008 Perimeter Technologies Inc All rights reserved Our products are covered by U S Patent Numbers 5 460 124 5 682 839 6 296 776 13010019 Rev A 0208
Download Pdf Manuals
Related Search