CM30/35 Switch User Manual - Command Auto Group Pty Ltd
Contents
1. COMMAND AUTO GROUP PTY LTD ABN 16 093 260 381 CM30 CM35 EURO STALK OPERATING INSTRUCTIONS The operating functions for both switches are identical with the CM35 providing two adjustable RESUME speed memory presets The switch arm moves in four directions up down toward you and away from you Push the switch arm away from you toward the dashboard to turn ON and the small soeedometer symbol will display green illumination To turn OFF push the switch arm away again the green light will go out SWITCH MOUNTED LEFT HAND SIDE To SET engage the Cruise Control lift the switch arm up toward the windscreen and the speedometer symbol will change to red illumination Once the Cruise Control has engaged lifting the switch arm again will increase the vehicle speed If you lift the arm and release it promptly the vehicle speed will increase by 1 KPH On AP300 and AP500 models pressing and holding the button will increase speed in a gentle and progressive manner holding the higher speed when the button is released On AP900 and AP900C models pressing and holding the button for approx 1 5 2 seconds will increase speed by 10kph above current set speed This is indicated by 2 brief beep tones when holding the SET ACC button for the required period The RESUME function will reset the Cruise Control to the last set soeed provided the ignition has not been turned off which cancels the standard RESUME memory function For CM35 MEMORY2. RESUME functions please see the separate notes on the next page To RESUME to the last SET speed push the switch arm down toward the floor and the speedometer symbol will display red illumination and the Cruise Control will engage at the last SET speed This may involve a progressive increase or decrease in speed until the last SET speed is achieved When the Cruise Control is engaged pushing the switch arm down again will decrease the vehicle soeed A prompt press and release will lower the speed by 1 KPH On AP300 and AP500 models pressing and holding the button will decrease speed in a gentle and progressive manner holding the lower speed when the button is released On AP900 and AP900C models pressing and holding the button for approx 1 5 2 seconds will decrease speed by 10kph below current set speed Again 2 brief 2 beep tones will confirm 10kph reduction is activated COMMAND COMMAND and the Command Logo are Trademarks of Command Auto Group Pty Ltd All rights reserved AUTO GROUP PTY LT COMMAND AUTO GROUP PTY LTD ABN 16 093 260 381 IMPORTANT NOTE The rate of vehicle deceleration can vary according to several factors including going down long or steep gradients towing carrying loads etc The Cruise Control cannot apply the vehicle brakes and the vehicle driver should be prepared to apply the brake pedal and take control if soeed is not reducing at the required rate To CANCEL disengage the Cruise Contro
3. her mechanical or electronic devices Further the company cannot be held liable for damage loss or injury that occurs from failure to understand and correctly apply this information or for action taken beyond that described in this or similar technical support documents or verbal advice provided by TCAG Technical staff COMMAND COMMAND and the Command Logo are Trademarks of Command Auto Group Pty Ltd All rights reserved AUTO GROUP PTY LTD COMMAND AUTO GROUP PTY LTD ABN 16 093 260 381 CM 30 35 Set Increase COommMmaAno COMMAND and the Command Logo are Trademarks of Command Auto Group Pty Ltd All rights reserved AUTO GROUP PTY LTD COMMAND AUTO GROUP PTY LTD ABN 16 093 260 381 CM 35 only N CommMmaAno COMMAND and the Command Logo are Trademarks of Command Auto Group Pty Ltd All rights reserved AUTO GROUP PTY LTD TM
4. l you can apply the brake pedal pull the switch arm toward you COAST function or switch the Cruise Control OFF SWITCH MOUNTED RIGHT HAND SIDE The ON OFF and COAST functions do not change The SET ACCELERATE and RESUME DECELERATE functions are reversed for right hand mounting Press switch arm down for SET and ACCELERATE functions Lift switch arm up for RESUME and DECELERATE functions CM35 MEMORY RESUME FUNCTIONS On the end of the CM35 switch arm there are two small buttons marked and Il These can be set to any RESUME speed of your choice Switch the Cruise Control ON and drive to the desired speed Press and hold the required button set first and then Il if required and you will hear a low volume beep tone The Cruise Control will engage and this speed will be saved for future use lf you wish to change this setting at any time simply repeat the above process at the new desired speed and this change will be saved when the beep tone is heard DISCLAIMER Command Auto Group Pty Lid hereafter referred to as the company provides this information as a diagnostic support service to customers to assist in fault finding automotive Cruise Control installations When followed correctly there is no risk of damage to the Cruise Control the vehicle to which it is fitted other property or personal injury The company cannot be held liable for damage loss or injury that occurs though product fitment to non specified vehicles or ot
Download Pdf Manuals
Related Search