Philips 47PFL3605H Tv User Guide Manual Operating Instructions Pdf
Contents
1. HIGH DEFINITION MULTIMEDIA INTERFACE HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC All other registered and unregistered trademarks are the property of their respective owners Downloaded From TV Manual com Manuals EN English 2 Important Read and understand all instructions before you use your TV If damage is caused by failure to follow instructions the warranty does not apply Safety Risk of electric shock or fire e Never expose the TV to rain or water Never place liquid containers such as vases near the TV If liquids are spilt on or into the TV disconnect the TV from the power outlet immediately Contact Philips Consumer Care to have the TV checked before use e Never place the TV remote control or batteries near naked flames or other heat sources including direct sunlight To prevent the spread of fire keep candles or other flames away from the T V remote control and batteries at all times e Never insert objects into the ventilation slots or other openings on the TV e When the TV is swivelled ensure that no strain is exerted on the power cord Strain on the power cord can loosen connections and cause arcing Risk of short circuit or fire e Never expose the remote control or batteries to rain water or excessive heat e Avoid force coming onto power plugs Loose power plugs can cause arcing or fire Risk2. Vivid Applies rich and dynamic settings e Standard Adjusts picture settings to suit most environments and types of video e Cinema Applies settings for movie viewing e Game Applies settings for games 12 EN Downloaded From TV Manual com Manuals e Energy saving Applies low energy settings e Natural Applies the best picture quality e Custom Lists customised picture settings J Press OK to confirm your choice L gt The selected smart picture setting is applied Manually adjust picture settings 1 Press amp MENU 2 Press AY 4b to select Setup gt Picture J Press AYP to select the following settings e Smart picture Accesses pre defined smart picture settings e Video contrast Adjusts the intensity of video contents keeping backlight unchanged e Contrast Adjusts the intensity of backlight areas keeping video contents unchanged Brightness Adjusts the intensity and details of dark areas e Colour Adjusts colour saturation e Hue Compensates for colour variations e Sharpness Adjusts sharpness in the image e Noise reduction Filters and reduces noise in an image Tint Adjusts the colour balance in an image e Custom tint Customises tint setting Only available if Tint gt Custom is selected e Digital Crystal Clear Fine tunes each pixel to match surrounding pixels This produces a brilliant high definition image e
3. When using the remote control hold it close to the TV and point it at the remote control sensor Make sure that the line of sight between the remote control and TV is not blocked by furniture walls or other objects 4 Use your TV This section helps you perform basic TV operations Switch your TV on off or to standby To switch on e Ifthe standby indicator is off press Power at the side of the TV e Ifthe standby indicator is red press Standby On on the remote control To switch to standby e Press Standby On on the remote control L gt The standby indicator switches to red To switch off e Press Power at the side of the TV L gt The standby indicator switches off Ea Though your TV consumes very little power when in standby energy continues to be consumed When not in use for an extended period of time disconnect the TV power cable from the power outlet Note f you cannot locate your remote control and want to switch on the TV from standby press P CH on the side of the TV Downloaded From TV Manual com Manuals Switch channels e Press P on the remote control or P CH on the side of the TV e Enter a channel number using the Numeric buttons e Press OK to use the channel grid e Press BACK P P on the remote control to return to the previous channel When you use a favourite li
4. Dynamic contrast Enhances contrast A Medium setting is recommended e Dynamic backlight Adjusts brightness of the TV backlight to match lighting conditions e MPEG artifact reduction Smoothes out transitions on digital pictures You can switch this feature on or off e Colour enhancement Makes colours more vivid and improves the details in bright colours You can switch this feature on or off e PC mode Adjusts the picture when a PC is connected to the TV via HDMI or DVI e Picture format Changes the picture format e Picture size Adjusts the viewing area when set to maximum you might see noise or a rough edge of an image e Horizontal shift Adjusts the picture horizontally for PC VGA DVI HDMI or YPbPr e Vertical shift Adjusts the picture vertically for PC VGA DVI HDMI or YPbPr Change picture format 1 Press FORMAT L gt A picture format bar appears 2 Press AY to select a picture format L gt The selected picture format is activated J Press OK to confirm your choice Summary of picture formats The following picture settings can be configured Note Depending on the format of the picture source some picture settings are not available Downloaded From TV Manual com Manuals Auto format Not for PC mode Enlarges the picture automatically to best fit the screen The subtitles remain visible Super zoom Not for HD and PC mode
5. Selects connected devices Colour buttons Selects tasks or options AD Audio Descriptor For RF Digital TV only UK only Enables audio commentary for the visually handicapped OPTIONS Accesses options relating to the current activity or selection OK Confirms an entry or selection and displays the channel grid when watching TV AY4b Navigation buttons Navigates menus INFO Displays program information when available If the information spans multiple pages press OPTIONS to go to the next page iK Mute Mutes or restores volume P Programme Switches to the next or previous channel When the TV menu is on this functions as Page Up Down 0 9 Numeric buttons Selects a channel or setting C PICTURE Smart picture Launches the picture menu EN Downloaded From TV Manual com Manuals 5 D 2 SOUND Smart Sound Launches the sound menu lt Volume Increases or decreases volume D BACK P P Previous channel e Returns to a previous screen e Returns to the previously viewed channel GUIDE Switches between channel grid and programme list SUBTITLE For RF Digital TV only Enables or disables subtitles DEMO Used in selected models only Toggles the demonstration menu on or off FORMAT Selects a picture format t INCR SURR Enables Incredible Surround for stereo sources Enables spatial mode for mono sources Remote control usage
6. TV location is set to the home setting This mode offers you the flexibility to change and save settings The picture does not fit the screen it is too big or too small e ry using a different picture format The picture position is incorrect e Picture signals from some devices may not fit the screen correctly Check the signal output of the device Sound issues There is a picture but sound quality is poor Note f no audio signal is detected the TV automatically switches the audio output off this does not indicate malfunction e Check that all cables are properly connected e Check that the volume is not set to 0 e Check that the sound is not muted There is a picture but the sound quality is poor e Check that the sound settings are correctly set There is a picture but sound comes from one speaker only e Verify that sound balance is set to the centre Downloaded From TV Manual com Manuals HDMI connection issues There are problems with HDMI devices Note that HDCP High bandwidth Digital Content Protection support can delay the time taken for a TV to display content from a HDMI device Ifthe TV does not recognise the HDMI device and no picture is displayed try switching the source from one device to another and back again If there are intermittent sound disruptions check that output settings from the HDMI device are correct If you use an HDMI to DVI adapter or HDMI
7. channels If digital broadcasting is available digital radio channels are installed automatically during installation 1 When watching TV press OK to display the channel grid 2 Press OPTIONS J Press a to select Select list gt Radio L gt The radio channel grid appears 4 Press AY4b to select a radio channel and press OK to listen Select Select list gt All to exit radio channels and view all channels EN 23 English Update the TV software Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available Check www philips com support for availability Check the current software version 1 Press amp MENU 2 Press AVP to select Setup gt Software update gt Current software info L gt The TV displays the current software information Download the software 1 on your PC open a web browser and go to www philips com support Download the latest software upgrade file to your PC 2 3 Decompress the ZIP file 4 Copy the autorun upg file to the root directory of the USB device Update software You can update the TV software via a USB storage device or OAD Over the Air software Download Update using a USB device Connect your USB storage device to the TV If the software update screen does not appear automatically select Setup gt Software update gt Local updates gt USB 2 Pre
8. of injury or damage to the TV e Two people are required to lift and carry a TV that weighs more than 25 kg 4 EN Downloaded From TV Manual com Manuals e When stand mounting the TV use only the supplied stand Secure the stand to the TV tightly Place the TV on a flat level surface that can support the combined weight of the TV and the stand e When wall mounting the TV use only a wall mount that can support the weight of the TV Secure the wall mount to a wall that can support the combined weight of the TV and wall mount Koninklijke Philips Electronics N V bears no responsibility for improper wall mounting that result in accident injury or damage Risk of injury to children Follow these precautions to prevent the TV from toppling over and causing injury to children e Never place the TV on a surface covered by a cloth or other material that can be pulled away e Ensure that no part of the TV hangs over the edge of the surface e Never place the TV on tall furniture such as a bookcase without anchoring both the furniture and TV to the wall or a suitable support e Educate children about the dangers of climbing on furniture to reach the TV Risk of overheating e Never install the TV in a confined space Always leave a space of at least 4 inches or 10 cm around the TV for ventilation Ensure curtains or other objects never cover the ventilation slots on the T V Risk of damage to the TV e Before you connect
9. screen Never touch push rub or strike the screen with any object e To avoid deformations and colour fading wipe off water drops as soon as possible Downloaded From TV Manual com Manuals Disposal of your old product and batteries es Your product is designed and manufactured with high quality materials and components which can be recycled and reused A When this crossed out wheeled bin symbol Is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health R Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed with normal household waste Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health EN 5 English ECO Green EUROPEAN UNION ECOLABEL pnt C Award to goods or services which meet the environmental requirements of the EU eco labelling scheme NL 22 001 e High energy efficiency e Low standby power e Desi
10. the TV to the power outlet ensure that the power voltage matches the value printed on the back of the TV Never connect the TV to the power outlet if the voltage is different Risk of injury fire or power cord damage e Never place the TV or any objects on the power cord e o disconnect the TV power cord easily from the power outlet ensure that you have full access to the power cord at all times e When you disconnect the power cord always pull the plug never the cable e Disconnect the TV from the power outlet and antenna before lightning storms During lightning storms never touch any part of the TV power cord or antenna cable Risk of hearing damage e Avoid using earphones or headphones at high volumes or for prolonged periods of time Low temperatures e Ifthe TV is transported in temperatures below 5 C unpack the TV and wait until the TV temperature matches room temperature before connecting the TV to the power outlet Screen care e Avoid stationary images as much as possible Stationary images are images that remain on screen for extended periods of time Examples include on screen menus black bars and time displays If you must use stationary images reduce screen contrast and brightness to avoid screen damage e Unplug the TV before cleaning e Clean the TV and frame with a soft damp cloth Never use substances such as alcohol chemicals or household cleaners on the TV e Risk of damage to the TV
11. to DVI cable check that an additional audio cable is connected to AUDIO IN mini jack only Computer connection issues The computer display on the TV is not stable Check that your PC uses the supported resolution and refresh rate Set the TV picture format to unscaled Contact us If you cannot resolve your problem refer to the FAOs for this product at www philips com support If the problem remains unresolved contact Philips Consumer Care in your country as listed in the Addendum Warning Do not attempt to repair the product yourself This may cause severe injury irreparable damage to your product or void your warranty Note Make a note of your TV model and serial number before you contact Philips These numbers are printed on the back of the TV and on the packaging EN 39 English 10 Index A analogue fine tune antenna B back connectors batteries bracket for wall mount C CAM care channel decoder channel grid channels favourites list fine tune grid install automatic manual list lock rename reorder rearrange switch test reception digital channels troubleshooting tune update child lock lock channels lock connected devices PIN code ratings lock clock display set common interface 40 EN Downloaded From TV Manual com Manuals 27 29 29 36 5 37 33 25 16 27 26 27 16 20 28 28 28 38 27 17 20 20 20 20 18 18 3
12. 3 computer connect display resolution Conditional Access Module connect antenna PC connectors back connectors HDMI overview side connectors USB content ratings country D daylight saving decoder default settings demo devices devices add to home menu connect remove rename watch digital channel subtitles test reception digital radio digital services CAM teletext disconnect USB display resolution dispose 39 32 33 29 39 32 29 39 29 29 31 22 20 26 19 25 25 25 10 11 29 11 11 10 21 28 23 26 33 16 10 15 23 36 5 E EasyLink disable enable one touch play one touch standby system audio control eco green end of life energy efficiency environmental care e sticker F factory settings favourites list add to list create list view list fine tune channels G green H HDMI hearing impaired home mode install channels automatic manual K Kensington lock Downloaded From TV Manual com Manuals 25 17 16 27 39 31 29 15 24 26 27 35 L language menu subtitle troubleshoot list favourites list location country home or shop lock Kensington lock lock channels lock connected devices PIN code ratings lock M menu language main menu teletext universal access MHEG teletext MPEG artifact reduction multimedia music digital radio USB with slideshow mute TV speakers O OAD on timer one touch play one touch st
13. 37 English 9 Troubleshooting This section describes commonly encountered issues and accompanying solutions General TV issues The TV does not switch on e Disconnect the power cable from the power outlet Wait for one minute then reconnect it e Check that the power cable is securely connected The remote control is not working properly e Check that the remote control batteries are correctly inserted according to the orientation e Replace the remote control batteries if they are flat or weak e Clean the remote control and TV sensor lens The standby light on the TV blinks red e Disconnect the power cable from the power outlet Wait until the TV cools down before reconnecting the power cable If the blinking reoccurs contact Philips Consumer Care You forgot the code to unlock the TV lock feature Enter 8888 The TV menu is in the wrong language e Change the TV menu to your preferred language When turning the TV on off to standby you hear a creaking sound from the TV chassis e No action is required The creaking sound is normal expansion and contraction of the TV as it cools down and warms up This does not impact performance 38 EN Downloaded From TV Manual com Manuals Cannot remove e sticker banner displayed on theTV e To remove the logos and images set the location of your TV to home 1 Press amp MENU 2 Select Setup gt Installation gt Preferences
14. G TELETEXT L gt The teletext screen appears 2 Press OPTIONS L gt The teletext options menu appears J Press Y to select one of the following options e Reveal Hides or reveals hidden information on a page such as solutions to riddles or puzzles e Cycle subpage Cycles through subpages automatically if subpages are available e Language Switches to a different language group to display a language correctly when it uses a different character set e Freeze page Freezes the current page e Dual screen Full Screen Enables and disables dual screen teletext 4 Press AV lt 4P to make a selection then press OK to confirm 5 Press gt BACK to exit the teletext options menu Select teletext subpages A teletext page can hold several subpages Subpages are displayed on a bar next to the main page number Press MHEG TELETEXT L gt The teletext screen appears 2 Press P to select a teletext page J Press lt P to enter a subpage EN 15 English Select T O P teletext broadcasts Table Of Pages T O P teletext broadcasts allow you to jump from one subject to another without using page numbers T O P teletext is not broadcast on all TV channels 1 Press MHEG TELETEXT L gt The teletext screen appears 2 Press CD INFO L gt The T O P overview appears J Press AY 4b to select a subject 4 Press OK to view the page Use Teletext 2 5 Teletext 2 5 offers more colours and b
15. GA DVI COMMON INTERFACE Connect a computer Before you connect a computer to the TV e Set the screen refresh rate on your AUDIO IN computer to 60Hz LEFT RIGHT VGA DVI e Select a supported screen resolution on your computer Connect a computer with one of the following connectors Note Connections via DVI or VGA require an additional audio cable HDMI cable e VGA cable AUDIO IN LEFT RIGHT 32 EN Downloaded From TV Manual com Manuals Use a Conditional Access Module A Conditional Access Module CAM is provided by digital TV service operators to decode digital TV channels Note Refer to the documentation from your service operator on how to insert a smart card into the Conditional Access Module Insert and activate a CAM Caution Be sure to follow the instructions described below Wrong insertion of a CAM may damage both the CAM and your T V 1 Switch off the T V and disconnect it from the power outlet 2 Following the directions printed on the CAM gently insert the CAM into the COMMON INTERFACE at the side of the TV J Push the CAM in as far as it will go 4 Reconnect the TV to the power outlet b Tum on the TV and wait for the CAM to be activated This may take several minutes Do not remove the CAM from the slot when in use removing the CAM will deactivate digital se
16. NU Press AY 4b to select Setup gt Installation gt Channel installation gt Automatic channel search Press OK or gt to enter the menu L gt The country menu appears Press AY to select your country Press OK to confirm your choice L gt The channel installation guide appears on the screen EN Downloaded From TV Manual com Manuals Step 3 Install channels Automatically installs the available analogue and digital TV channels and digital radio channels 1 2 W From the channel installation guide screen select Full installation Press OK to confirm L gt The TV starts to search and store all the available channels When installation is complete press OK to exit the installation menu Update the channel list You can enable automatic update of channels when your TV is in standby mode The channels stored in your T V are updated every morning according to the channel information in the broadcast 1 2 Press MENU Press AY 4b to select Setup gt Installation gt Channel installation gt Standby update Select On to enable the automatic update or select Off to disable it Manually install channels This section describes how to search and store analogue I V channels manually Step 1 Select your system Note Skip this step if your system settings are correct 1 Press amp MENU 2 Press AVP to select Setup gt Installation gt Cha
17. Register your product and get support at www philips com welcome 32PFL3605H 12 42PFL3605H 12 47PFL3605H 12 EN User Manual PHILIPS Downloaded From TV Manual com Manuals Osterreich Belgi Belgique bbArapua Hrvatska Cesk republika Danmark Estonia Suomi France Deutschland E Adda Magyarorszag Hrvatska Ireland Italia KasakcraH Latvia Lithuania Luxemburg Luxembourg Nederland Norge Polska Portugal Romania Poccua Cp6nija Slovensko Slovenija Espana Sverige Suisse Schweiz Svizzera Turkiye United Kingdom YkpaiHa 0810 000 205 078250145 3592 489 99 96 01 6403 776 800142840 3525 8759 6008600 09 2311 3415 0805 025 510 0800 000 7520 0 0800 3122 1280 0680018189 0800 222778 North 0800 055 6882 South 1800 PHILIPS 7445477 800 088774 7 727 250 66 17 52737691 67228896 40 6661 5644 0800 0230076 22 70 81 11 022 349 15 05 800 780 903 0800 894910 0318107125 495 961 1111 381 114 440 841 0800 004537 00386 12 80 95 00 900 800 655 08 5792 9100 0844 800 544 0800 261 3302 General No 0800 331 6015 General National Rate No 0870 911 0036 8 800 500 69 70 Model Serial 0 07 pro Minute 0 03 Per minuut Par minute MecteH pasroBop Lokalni poziv Bezplatny hovor Lokalt opkald kohalik kone tariifi paikallispuhelu num ro sans frais geb hrenfreier Anruf KArjen xwpic xpewon Ingyenes hivas free free Numero Verde local loc
18. Removes the black bars on the side of 4 3 broadcasts There is minimal distortion 4 3 Shows the classic 4 3 format Subtitle zoom Displays 4 3 pictures over the full area of the screen with sub titles visible Part of the top of the picture is clipped off Movie expand 14 9 Not for HD and PC mode Scales 4 3 format to 14 9 Movie expand 16 9 Not for HD and PC mode Scales 4 3 format to 16 9 Wide screen Scales 4 3 format to 16 9 Unscaled For HD and PC mode only and in selected models only Allows maximum sharpness Some distortion may be present due to the broadcaster s systems Set your PC resolution to wide screen mode for best results EN 13 English Use smart sound Use smart sound to apply pre defined sound settings 1 Press SOUND L gt The Smart sound menu appears 2 Press AY to select the following settings e Custom Applies the settings that were customised in the sound menu e Standard Adjusts sound settings to suit most environments and types of audio e News Applies settings for spoken audio such as news e Movie Applies settings for movies J Press OK to confirm your choice L gt The selected smart sound setting is applied Manually adjust sound settings 1 Press amp MENU 2 Press AVP to select Setup gt Sound L gt The Sound menu appears J Press AVP to select the following settings e Smart sound Accesses pre def
19. Su mau BEREEREEREA BESEEREEEN 3 SPDIF OUT Digital audio output to home theatres and other digital audio systems SPDIF OUT EN 29 English 4 SERV U 7 EXT 3 Y Pb Pr and AUDIO L R For use by service personnel only Analogue audio and video input from PC IN VGA and AUDIO IN e E Audio and video input from a computer EU l VGA AUDIO IN LEFT RIGHT GA DVI 6 HDMI 1 Digital audio and video input from high definition digital devices such as Blu ray players Connections via DVI or VGA require an additional audio cable see Connect a computer on page 32 30 EN Downloaded From TV Manual com Manuals Side connector L AUDIO R COMMON INTERFACE 1 AUDIO L R Audio input from analogue devices connected to VIDEO 2 VIDEO Composite video input from analogue devices such as VCRs 3 UsB Data input from USB storage devices 1 ta o 4 HDMI Digital audio and video input from high definition digital devices such as Blu ray players L AUDIO R 4 Blu ray Disc Downloaded From TV Manual com Manuals M Headphone Stereo audio output to headphones or earphones EN 31 English COMMON INTERFACE e DVI HDMI cable Slot for a Conditional Access Module CAM AUDIO IN LEFT RIGHT V
20. Tip View all channels before adding a channel to a favourite list When watching TV press OK L gt The channel grid appears 2 Press AY4b to select a channel to add to a favourite list Press 2 OPTIONS L gt The channel options menu appears 4 Select Mark as favourite then press OK L gt The channel is added to the favourite list Note All favourite channels are marked by an asterisk in the channel grid Remove a channel from a favourite list 1 When watching TV press OK L gt The channel grid appears 2 Press AV lt 4P to select a channel to remove 3 Press OPTIONS 4 Select Unmark as fav then press OK L gt The channel is removed Downloaded From TV Manual com Manuals Use the Electronic Programme Guide EPG is an on screen guide available for digital channels EPG allows you to View a list of digital programmes being broadcast e View upcoming programmes e Group programmes by genre Set reminders when programmes start e Set up preferred EPG channels Switch on EPG 1 When watching TV press GUIDE L gt The EPG planner screen appears displaying information about the scheduled programmes EPG data is available only in selected countries and can take some time to load Use EPG 1 When watching TV press GUIDE L gt The EPG planner screen appears 2 Press amp MENU L gt The program guide menu appears J Press A
21. U to exit f your selected country supports digital broadcast the clock displays the time data from your TV service operator as priority Display the TV clock 1 when watching TV press OPTIONS L gt The TV option menu appears 2 Select Clock 3 Press OK o disable the clock repeat the above procedure Change the clock mode 1 Press amp MENU 2 Press AY 4b to select Setup gt Installation gt Clock gt Auto clock mode 3 Press AYx to select Automatic or Manual 4 Press OK to confirm Change the time zone 1 Press amp MENU Press AY 4b to select Setup gt Installation gt Clock gt Time zone J Press AY to select your time zone Press OK to confirm Note his option is only available if you select Auto clock mode gt Manual in countries with clock transmission data Use daylight saving 1 Press MENU 2 Press AVP to select Setup gt Installation gt Clock gt Daylight saving J Press OK or to enter Daylight saving 4 Press AY to select Standard time or Daylight saving time 5 Press OK to confirm Note This option is only available if you select Auto clock mode gt Manual Use timers You can set timers to switch the TV to standby at a specified time Tip Set the TV clock before you use timers Automatically switch the TV to standby sleep timer Slee
22. YP to select an option and then press OK to confirm 4 Press MENU to exit the EPG menu Only the channels in the Preferred EPG channels list appear in the EPG menu EN 17 English Use the EPG options menu Use the EPG options menu to set or clear reminders change day and access other useful EPG options 1 Press GUIDE 2 Press OPTIONS L gt The EPG menu appears J Press Y to select one of the following options e Set remind Clear remind Sets or clears programme reminders e Change day Sets the EPG day e Show info Displays programme information e Search by genre Searches TV programmes by genre Scheduled reminders Lists programme reminders Only available for upcoming programmes e Preferred EPG channels Sets preferred EPG channels 4 Press OK to enter or activate the option D Press 4 BACK to exit the EPG menu Ea Press i GUIDE to switch between EPG and channel grid Use the TV clock You can display a clock on the TV screen The clock displays the current time using time data received from your TV service operator Set the TV clock manually In some countries you need to set T V clock manually 1 Press amp MENU 2 Select Setup gt Features gt Clock L gt The Clock menu appears 18 EN Downloaded From TV Manual com Manuals 3 Press AV lt 4P to enter time 4 Select Done to confirm D Press MEN
23. al local Ortsgesprach Appel local Gratis nummer Lokalsamtale Monitory i akcesoria komputerowe Chamada Gratis Apel gratuit Apel local 0 15 USD minute Lokalni poziv Bezplatny hovor lokalni klic Tel fono local gratuito solamente para clientes en Espana Lokalsamtal Schweizer Festnetztarif Sehirici arama free National rate Micuesun BAKAMK Downloaded Fhisrinformation is cormectiat the time of press For updated information see www philips com support Contents 1 Notice 2 2 Important 4 3 YourTV 7 Side controls and indicators 7 Remote control 7 4 Use your TV 9 Switch your TV on off or to standby 9 Switch channels 9 Watch connected devices 10 Adjust TV volume 10 Use teletext 10 5 Use more of your TV 11 Access V menus 11 Rename devices from the home menu 11 Remove devices from the home menu 11 Change picture and sound settings 12 Use the universal access menu 15 Use advanced teletext features 15 Create and use list of favourite channels 16 Use the Electronic Programme Guide 17 Use the TV clock 18 Use timers 19 Use TV locks 20 Use subtitles 21 View photos and play music from a USB storage device 22 Listen to digital radio channels 23 Update the TV software 24 Change TV preferences 24 Access decoder channel 25 Start a TV demo 25 Reset the TV to factory settings 25 Downloaded From TV Manual com Manuals 6 Install channels Automatically install channels Manually inst
24. al access menu e EasyLink Enables one touch play and one touch standby between EasyLink compliant devices e Pixel Plus Link Overrides the settings of connected devices and uses the settings of the TV Only available if EasyLink is switched on e Teletext 2 5 Enables or disables Teletext 2 5 For digital TV e E sticker For shop mode only Sets the location of the e sticker Press AY 4b to select your preference Press OK Press MENU to exit Uni GW Access decoder channel You can map channels provided through a decoder or descrambler to your TV channel selection In this way you can select these channels by using the RC of your TV The decoder or a descrambler must be connected to EXT1 SCART Set decoder channel Map channels from a decoder or descrambler 1 Press amp MENU 2 Select Setup gt Installation gt Decoder J Press to enter Decoder menu 4 Press a to select Channel then press to enter 5 Select one channel to map to the decoder descrambler channel and press OK to confirm Select Status then press to enter Select EXT 1 SCART the connector used by the decoder descrambler NO Downloaded From TV Manual com Manuals 8 Press OK 9 Press MENU to exit Select None if you do not want to map to the decoder descrambler channel Start a TV demo You can use demonstrations to better understand the features
25. all channels Rename channels Rearrange channels Test digital reception Connect devices Back connector Side connector Connect a computer Use a Conditional Access Module Use Philips EasyLink Use a Kensington lock Product information Supported display resolutions Multimedia Tuner Reception Transmission Remote control Power Supported TV mounts Product specification Troubleshooting General TV issues TV channel issues Picture issues Sound issues HDMI connection issues Computer connection issues Contact us 10 Index EN 26 26 27 28 28 28 29 29 31 32 33 34 35 38 38 38 38 39 39 39 39 40 English 1 Notice 2010 Koninklijke Philips Electronics N V AIl rights reserved Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly The material in this manual is believed adequate for the intended use of the system If the product or its individual modules or procedures are used for purposes other than those specified herein confirmation of their validity and suitability must be obtained Philips warrants that the material itself does not infringe any United States patents No further warranty is expressed or implied Warranty e Risk of injury damage to TV or
26. alogue channel Tip Select Subtitle mode gt Off to disable subtitles Enable subtitles on digital TV channels 1 When watching digital channels press SUBTITLE L gt The Subtitle mode menu appears 2 Select On to display subtitles always or On during mute to display subtitles only when audio is muted 3 Press OK to enable subtitles Downloaded From TV Manual com Manuals Select a subtitle language on digital TV channels Note When you select a subtitle language on a digital TV channel as described below the preferred subtitle language set in the installation menu is temporarily overruled Press f MENU Press AY 4b to select Setup gt Features gt Subtitle language Press OK or gt to enter the list of available languages Press AY to select a subtitle language UA WwW N Press OK to confirm Ea You can also access the Subtitle language menu while watching TV by pressing OPTIONS gt Subtitle language EN 21 English View photos and play music from a USB storage device EB Caution Philips is not responsible if the USB storage device is not supported nor is it responsible for damage or loss of data from the device Use the USB connector to view photos or isten to music stored on a USB storage device 1 Turn on the TV 2 Connect the USB storage device to the TY L gt The home menu appears Press AY 4b to sele
27. andby 26 38 16 26 24 35 20 20 20 20 26 11 15 15 10 12 36 23 23 23 34 24 19 19 EN 34 34 41 English P parental rating PC connect resolution picture format change troubleshooting picture settings PIN code pixel plus link power power consumption preferences product specifications R radio rearrange channels reception recycle register product remote control batteries overview technical specifications rename channels reorder channels resolution restore default S safety screen care settings picture sound settings assistant shop mode side connectors slideshow view with music smart card smart picture smart settings 42 EN Downloaded From TV Manual com Manuals 20 32 39 36 13 12 20 24 36 36 6 24 36 23 28 28 38 36 5 36 28 28 36 25 12 14 12 12 24 31 smart sound 14 software over the air download 24 update 24 version 24 sound settings 14 specifications 36 standby 9 subpages in teletext 15 subtitles language 21 on analogue channel 21 on digital channel 21 switch channels 9 on and off 9 source 10 T Table of Pages 16 technical specifications 36 teletext features 15 menu 15 subpages 15 Table of Pages 16 Teletext 2 5 16 use 10 time zone 18 timer on timer 19 19 sleep timer 19 standby 19 transmission 36 38 transporting 4 troubleshooting 38 TV lock lock channels 20 lock con
28. ards applicable at the time of producing the products Philips is committed to develop produce and market products that cause no adverse health effects Philips confirms that if its products are handled properly for their intended use they are safe to use according to scientific evidence available today Philips plays an active role in the development of international EMF and safety standards enabling Philips to anticipate further developments in standardisation for early integration in tts products Mains fuse UK only This TV is fitted with an approved moulded plug Should it become necessary to replace the mains fuse this must be replaced with a fuse of the same value as indicated on the plug example 10A 1 Remove fuse cover and fuse 2 The replacement fuse must comply with BS 1362 and have the ASTA approval mark If the fuse is lost contact your dealer in order to verify the correct type J Refit the fuse cover In order to maintain conformity to the EMC directive the mains plug on this product must not be detached from the mains cord cable Copyright Kensington and Micro Saver are registered US trademarks of ACCO World corporation with issued registrations and pending applications in other countries throughout the world I DOLBY DIGITAL PLUS Manufactured under licence from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories Available in selected models only
29. check the quality and signal strength of digital channels This allows you to reposition and test your antenna or satellite dish 1 Press amp MENU 2 Press AY 4b to select Setup gt Installation gt Channel installation gt Manual channel search Press to enter the menu Press amp lt 4P to enter the frequency of the channel you want to test Press OK to confirm the frequency then press OK again to confirm Search Oo wo HRW When complete select Store to store the frequency Note Ifthe signal quality and strength is poor reposition the aerial or satellite dish and retest f you still have problems with the reception of your digital broadcast contact a specialised installer 7 Connect devices This section describes how to connect devices with different connectors Examples are provided in the Quick Start You can use different types of connectors to connect a device to your TV Back connector EXT 2 EXT 1 CVBS RGB CVBS TV ANTENNA COT N COCE E OLI N COCE b Y XT AUDIO IN LEFT RIGHT VGA DVI Downloaded From TV Manual com Manuals 1 TV ANTENNA Signal input from an antenna cable or satellite 150 r TV ANTENNA 2 EXT 1 and EXT 2 CVBS and RGB Analogue audio and video input from analogue or digital devices such as DVD players or game consoles EXT I RGBICVBS m zm mu mu m m gL OL mu
30. chover happens in your area there are at least two occasions when you will need to re tune your TV in order to continue receiving your existing TV channels and also to pick up new ones get set for digital Digital UK the body leading the digital TV How to re tune switchover will advise you when you need to re tune during the switchover If you choose to connect your TV to satellite or this user manual for details cable with a digital box then it will not be Go to section 6 Install channels affected by switchover and you won t need to To find out how to re tune your TV check re tune If you have any questions please contact your equipment supplier or call Digital UK on 0845 6 50 50 50 or visit www digitaluk co uk If you do not re tune your channels when advised to do so by Digital UK you may lose some or all of your channels until you do re tune You should re tune your TV every few months to check for any new channels If you are missing any channels it may be that they are not available in your area or that your aerial needs upgrading When does switchover happen ary Li Copeland switches on October 17 2007 P x e sf Shetland Islands t US STV North 2 2010 4 r gt s 4 STV Central 2010 11 ei Border 2008 09 Tyne Tees 2012 Yorkshire 2011 Central Anglia Wales ies 2009 10 Visit us at digitaluk co uk Call us on 0845 6 50 50 50t v London 2012 M
31. ct Browse USB 3 4 Press OK to confirm L gt The USB thumbnail browser appears Tip e Press il GUIDE to switch between thumbnail and file browsing views View photos 1 Inthe USB browser press to enter the Picture folder 2 Press AVP to select a photo or a photo album J Press OK to view a full screen image of the photo El e When in full screen mode press lt P to move between photos 22 EN Downloaded From TV Manual com Manuals View a slide show of your photos 1 When a full screen image of a photo is displayed press OK L gt A slide show begins from the selected photo 2 Press the following buttons to control the slide show e OK to pause the slide show e 4k to go back or move forward to the next image e 2 BACK to stop the slide show Change slide show settings 1 when viewing a slide show press OPTIONS L gt The slide show options menu appears 2 Press av to select one of the following e Start Slideshow Stop Slideshow Starts or stops a slide show e Slideshow transitions Sets the transition from one picture to the next e Slideshow frequency Sets the amount of time that a picture is shown e Rotate image Rotates a picture e Show info Displays the picture name date size and next picture in the slide show J Press OK to confirm your setting Rotate image and Show info appear only when you press OK to pause the sli
32. deshow Listen to music 1 n the USB thumbnail browser view select Music and press gt to enter Press i GUIDE to switch between thumbnail and file browsing views 2 Press AY 4b to select a music track or album J Press OK to play the selected music Button Function OK Pause resume play or stop playback lt gt Go to the previous or next music Music settings When listening to music press amp OPTIONS to access one of the following music settings e Start playback Stop playback Starts or stops the music e Repeat Play once Repeats a song Disables repeat play and plays a song or album once e Shuffle on Shuffle off Enables or disables random play of songs e Show info Displays the file name e TV speakers Sets the TV speakers on or off Only available if EasyLink is switched on e Sound Adjusts the sound setting View a slideshow with music You can view a picture slide show with background music 1 Select an album of songs Press OK Press D gt BACK to return to the USB content browser UJ N Select an album of pictures Press OK UIA Downloaded From TV Manual com Manuals Disconnect a USB storage device Caution Follow this procedure to avoid damage to your USB storage device 1 Press BACK to exit the USB browser 2 Wait for five seconds then disconnect the USB storage device Listen to digital radio
33. e Type PFO1EO9B e Batteries 2 x AAA LRO3 type Power e Mains power 220 240V 50Hz Standby power lt 0 3 W e Ambient temperature 5 to 40 degrees Celsius Supported TV mounts To mount the TV purchase a Philips TV mount or a VESA compatible TV mount To prevent damage to cables and connectors be sure to leave a clearance of at least 2 2 inches or 5 5cm from the back of the TV VN Warning Follow all instructions provided with the TV mount Koninklijke Philips Electronics N V bears no responsibility for improper TV mounting that results in accident injury or damage TV screen Required Required size pitch mm mounting bolts inches 34 200x200 4xM6 lt 10 mm 42 300x200 4xM6 lt 10 mm 47 400x300 4xM8 lt 12 mm Downloaded From TV Manual com Manuals Product specification Design and specifications are subject to change without notice 32PFL3605H e Without TV stand Dimension WxHxD 795 6 x 508 3 x 93 mm e Weight 8 3 kg e With TV stand Dimension WxHxD 795 6 x 556 6 x 220 8 mm e Weight 9 4 kg 42PFL3605H e Without TV stand Dimension WxHxD 1018 5 x 635 7 x 83 mm e Weight 11 5 kg e With TV stand Dimension WxHxD 1018 5 x 683 x 235 8 mm e Weight 12 8 kg 47PFL3605H e Without TV stand Dimension WxHxD 1129 8 x 700 7 x 83 mm e Weight 16 8 kg e With TV stand Dimension WxHxD 1129 8 x 746 4 x 270 1 mm e Weight 19 8 kg EN
34. e code menu appears J Enter your code using the Numeric buttons L gt Follow the on screen instructions to create or change your PIN code Tip f you forget your code enter 8888 to override any existing codes Lock or unlock the TV Lock the TV to prevent access to all channels and connected devices 1 Press amp MENU 2 Press AYP to select Setup gt Features gt TV lock L gt You are prompted to enter your PIN code J Enter your code using Numeric buttons The TV lock menu appears 4 Press AY to select Lock or Unlock 5 Press OK to confirm L gt All channels and connected devices are locked or unlocked 6 Press amp MENU to exit Switch the TV off and on again for the change to take effect f you select Lock you have to enter your code every time you turn on your TV 20 EN Downloaded From TV Manual com Manuals Lock or unlock one or more channels 1 when watching TV press OK to display the channel grid Press AY4b to select a channel to lock or unlock Press OPTIONS Press AY to select Lock channel or Unlock channel U AUW N For each selection press OK to lock or unlock the channel L gt The first time you lock or unlock a channel you are prompted to enter your PIN code 6 Enter your code and press OK L gt If the channel is locked a lock icon is displayed 7 Repeat the process to lock or unlock more channels S
35. eridian 2012 West Country B 2009 T Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends Rates may vary for calls from non BT lines Downloaded From TV Manual com Manuals 46 EN Downloaded From TV Manual com Manuals PHILIPS 2010 Koninklijke Philips Electronics N V All rights reserved Downloaded From TV Manual com Manuals
36. etter graphics than normal teletext If Teletext 2 5 Is broadcast by a channel it is switched on by default 1 Press MENU 2 Press AVP to select Setup gt Installation gt Preferences gt Teletext 2 5 Press AY to select On or Off Press OK to confirm your choice A Ww 16 EN Downloaded From TV Manual com Manuals Create and use list of favourite channels You can create a list of your preferred TV channels so that you can find those channels easily Select a favourite list 1 When watching TV press OK to display the channel grid 2 Press OPTIONS L gt The channel options menu appears J Press AY to select Select list then press OK to enter L gt The channel list options appear 4 Select Favourite then press OK L gt Only channels in the favourite list appear in the channel grid The favourite channel grid is empty until you add channels into the favourite lists View all channels You can exit a favourite list and view all installed channels 1 when watching T V press OK L gt The channel grid appears 2 Press OPTIONS L gt The channel options menu appears J Press Av to select Select list then press OK or gt to enter 4 Select All then press OK Ly All channels are displayed in the channel grid Note All favourite channels are marked by an asterisk when you view the channel grid Add a channel to a favourite list
37. g devices The device name can be up to 16 characters long Press Aa to change an uppercase letter to a lowercase letter and vice versa NO UI Remove devices from the home menu If a device is no longer connected to the TV remove it from the home menu 1 Press amp MENU Press AY4b to select a device to remove Press OPTIONS 2 3 4 Press AY to select Remove device then press OK 5 Select Remove then press OK L gt The selected device is removed from the home menu EN 11 English Change picture and sound settings Change picture and sound settings to suit your preferences You can apply pre defined settings or change settings manually When watching TV or using external devices press OPTIONS then select Picture and sound for quick access to picture and sound settings Use settings assistant Use the settings assistant to guide you through the picture and sound settings 1 Press amp MENU 2 Press AYP to select Setup gt Picture gt Settings assistant J Press OK L gt The Settings assistant menu appears Follow the on screen instructions to choose your preferred picture settings Use smart picture Use smart picture to apply pre defined picture settings 1 Press O PICTURE L gt The Smart picture menu appears 2 Press av to select one of the following settings e Personal Applies the settings set in Settings assistant menu
38. gned to facilitate recycling Philips continuously focuses on lowering the environmental impact of its innovative consumer products We aim our efforts towards environmental improvements during manufacturing reduction of harmful substances energy efficient use end of life instructions and product recycling Thanks to our environmental effort this TV has been awarded the European Ecolabel the flower www ecolabel eu You can find detailed information on standby energy consumption warranty policy spare parts and recycling of this TV on the Philips website for your country at www philips com This TV has features that contribute to energy efficient use This TV was awarded the European Ecolabel for its environmental qualities Energy efficiency features e Ambient light sensor Available in selected models only To save energy the built in Ambient light sensor lowers the brightness of the TV screen when the surrounding light darkens Energy saving The energy saving setting of the TV combines several TV settings that result in saving energy See the smart settings in the setup menu 6 EN Downloaded From TV Manual com Manuals e Low standby power consumption The class leading and highly advanced power circuitry brings down the power consumption of the TV to an extremely low level without losing out on the constant standby functionality Power management Available in selected models only The advanced power manageme
39. gt Location 3 Select Home and press OK TV channel issues Previously installed channels do not appear in the channel list e Check that the correct channel list is selected No digital channels were found during the installation e Check that the TV supports DVB T DVB T Lite or DVB C in your country Some channels are not automatically installed on my TV e During installation make sure that you select the country where you are installing the TV see Step 2 Select your country on page 26 Picture issues The TV is on but there is no picture e Check that the antenna is properly connected to the TV e Check that the correct device is selected as the T V source There is sound but no picture e Check that the picture settings are correctly set There is poor TV reception from an antenna connection e Check that the antenna is properly connected to the TV e Loudspeakers unearthed audio devices neon lights high buildings and other large objects can influence reception quality If possible try to improve the reception quality by changing the antenna direction or moving devices away from the TV e If reception on only one channel is poor fine tune this channel There is poor picture quality from connected devices e Check that the devices are connected properly e Check that the picture settings are correctly set The TV did not save your picture settings e Check that the
40. ices Switch to the connected device before you change the delta volume SPDIF OUT Selects the type of digital audio output through SPDIF connector e PCM Converts non PCM audio type to PCM format e Multichannel Outputs audio to the home theater Use the universal access menu You can activate the universal access menu during the first installation Once enabled you can quickly access the visually impaired and hearing impaired menus when watching TV or external devices Tip You can also enable the universal access menu by selecting Setup gt Installation gt Preferences gt Universal access gt On 1 When watching TV press OPTIONS L gt The TV options menu appears 2 Select Universal access then press OK or gt to enter J Press lt P to select one of the following options and press OK to enter e Hearing impaired Enables or disables hearing impaired subtitles e Visually impaired Selects speaker headphone or both for Vol vis impaired audio Select Off to disable audio descriptor Only applicable to the UK region e Vol vis impaired Adjusts the volume of visually impaired audio Tip Press the colour buttons on the remote control to enter the options Downloaded From TV Manual com Manuals Use advanced teletext features Access the teletext options menu Access the teletext features through the teletext options menu 1 Press MHE
41. ined smart sound settings e Bass Adjusts the bass level e Treble Adjusts the treble level e Digital audio lipsync Enables or disables lipsync audio output When this is enabled the TV synchronises the audio and video performance When disabled you need to adjust the lipsync audio feature on the external device that is connected to the TV Only available with SPDIF connection e Volume Adjusts the volume e Volvis impaired Sets the mix of visually impaired audio with regular audio When available visually impaired audio includes audio descriptions of on screen action You can also enable this by pressing AD Audio Descriptor Only applicable for the UK region 14 EN Downloaded From TV Manual com Manuals Balance Adjusts the balance of the right and left speakers Audio language Available for digital channels when multiple languages are broadcast Lists available audio languages Dual I II Selects audio languages if dual sound broadcast is available Mono Stereo Selects mono or stereo if stereo broadcast is available TV speakers Turns TV speakers on or off Only available if EasyLink is switched on Surround Enables spatial sound Headphone volume Adjusts headphone volume Auto volume levelling Automatically reduces sudden volume changes for example when switching channels Delta volume Levels out volume differences between channels or connected dev
42. nected devices 20 PIN code 20 ratings lock 20 TV overview 7 U universal access menu USB disconnect USB listen to music update software view photos V video format technical specifications volume adjust automatic levelling delta mute 15 23 23 24 24 36 10 14 14 10 34 W wall mount Downloaded From TV Manual com Manuals 4 37 EN 43 English Information about how to re tune your TV during the TV switchover Keep this user manual safe you ll need it pun o n Television in the UK is going digital bringing us all more choice and new services Starting in late 2007 and ending in 2012 television services in the UK will go completely digital TV region by TV region Please see the next page to find out when your area switches to digital Digital UK is the independent non profit organisation leading the process of digital TV switchover in the UK Digital UK provides im partial information on what people need to do to prepare for the move to digital and when they need to do it 44 EN Downloaded From TV Manual com Manuals How the switchover affects your TV equipment Your new TV has a digital tuner built in which means it is ready to receive the Freeview signal by simply plugging it into your aerial socket check if you can get digital TV through your aerial now or whether you ll have to wait until switchover at www digitaluk co uk When the TV swit
43. nnel installation gt Analogue manual install The Analogue manual install menu appears Press AY to select System then press gt to enter Press AY to select your country or region Press OK to confirm ONU A W Press 4 to return to Channel installation menu Step 2 Search and store new TV channels 1 Press amp MENU 2 Press AVP to select Setup gt Installation gt Channel installation gt Analogue manual install The Analogue manual install menu appears J Press Av to select Search then press gt to enter 4 Press AVP to manually enter the three digit frequency b Press OK to begin search L gt Ifa channel is unavailable at the selected frequency press OK to search for the next available channel Downloaded From TV Manual com Manuals 6 Press gt BACK when the new channel is found 7 Press AYx to select Store as new channel to store the new channel under a new channel number 8 Press OK to enter Store as new channel then press OK 9 Press 4 to return to the Channel installation menu Step 3 Fine tune analogue channels 1 Press amp MENU 2 Press AVP to select Setup gt Installation gt Channel installation gt Analogue manual install The Analogue manual install menu appears Press AY to select Fine tune then press gt to enter Press AY to adjust frequency Press OK to confirm Press AY to select Store curre
44. nt channel to store the channel number Press to enter Store current channel then press OK Press 4 to return to the Channel installation menu CO N AUA W EN 27 English Rename channels You can rename channels The name appears when you select the channel 1 When watching TV press OK to display the channel grid 2 Select the channel to rename 3 Press OPTIONS L gt The channel options menu appears 4 Press AY to select Rename channel then press OK L gt A text input box appears Press AY 4b to select characters Press OK to confirm each character Select Done then press OK to finish renaming channels Ea Press Aa to change an uppercase letter to a NO UI lowercase letter and vice versa Rearrange channels After you install channels you can rearrange the order in which they appear 1 When watching TV press OK to display the channel grid Press OPTIONS L gt The channel options menu appears OK Select the channel to rearrange then press OK L gt The selected channel is highlighted 2 J Press AYx to select Reorder then press 4 D Press AVP to move the highlighted channel to the desired location then press OK 6 Press OPTIONS Done reordering appears on the screen Press OK to confirm 8 Press gt BACK to exit the channel grid 28 EN Downloaded From TV Manual com Manuals Test digital reception You can
45. nt of this TV ensures the most efficient use of its energy You can check how your personal TV settings the level of brightness in current onscreen pictures and the surrounding light conditions determine the relative power consumption End of use To inform yourself on the correct disposal of the TV and batteries refer to Disposal of your old product and batteries in the user manual see Disposal of your old product and batteries on page 5 3 You r TV Remote control Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your TV at S www philipscom welcome 9 qq eL o This section gives you an overview of commonly used TV controls and functions Side controls and indicators PHILIPS TELEVISION 4 lt Increases or decreases volume D A Home Toggles the home menu on or off G P CH Switches to the next or previous channel 4 Power Switches the product on or off The product is not powered off completely unless it is physically unplugged Standby indicator and remote control sensor EN Downloaded From TV Manual com Manuals English 8 Standby On e Switches the TV to standby if it is on e Switches on the TV if it is in standby f MENU Toggles the main menu on or off MHEG TELETEXT Toggles teletext on or off amp SOURCE
46. of your TV Some demos are not available on certain models Available demos are displayed in the menu list 1 Press DEMO on the remote control 2 Press AY to select a demo and press OK to view it 3 Press DEMO to exit Reset the TV to factory settings You can restore the default picture and sound settings of your TV The channel installation settings remain the same 1 Press amp MENU Select Setup gt Installation gt Factory settings Press gt to enter Factory settings Select Reset to start resetting Press OK Press amp MENU to exit Oo U1 BK CJ EN 25 English 6 Install channels The first time you set up your TV you are prompted to select a menu language and to install TV and digital radio channels if available This chapter provides instructions on how to re install and fine tune channels Automatically install channels This section describes how to search and store channels automatically Step 1 Select your menu language 1 2 Oo U1 CJ Press MENU Press AY 4b to select Setup gt Installation gt Language gt Menu language Press OK or gt to enter Menu language Press AY to select a language Press OK to confirm Press lt to return to Installation menu Step 2 Select your country Select the country where you are installing the TV The available channels for the country are installed on the TV 1 2 Un A 26 Press ft ME
47. olour buttons to select a colour coded item e Press BACK to return to a previously viewed page Press MHEG TELETEXT to exit teletext For UK users only Some digital TV channels offer dedicated digital text services for example BBC1 5 Use more of your IV Access TV menus Menus help you to install channels change picture and sound settings and access other features 1 Press amp MENU L gt The menu screen appears y Add new device c T d Setup 2 Press AVP to select and navigate through one of the following menus e Watch TV Switches back to the aerial source if another source is selected e Add new device Adds new devices to the home menu Setup Accesses menus to change picture sound and other settings J Press OK to confirm your choice 4 Press amp MENU to exit Ea After selecting Add new device follow the on screen instructions to select the correct device and connector Downloaded From TV Manual com Manuals Rename devices from the home menu After adding a new device to the home menu you can rename it to your preference 1 Press amp MENU 2 Press AY4b to select a device to rename 3 Press OPTIONS L gt The options menu appears 4 Press AY to select Rename device then press OK L gt A text input box appears Press AY4b to select characters Press OK to confirm each character Select Done then press OK to finish renamin
48. p timer switches the TV to standby after a pre defined period of time Tip You can switch off your TV earlier or reset the sleep timer during the countdown Press ft MENU Press AY 4b to select Setup gt Features gt Sleep timer L gt The Sleep timer menu appears NA 3 Press lt P to select a value between zero and 180 minutes L gt The sleep timer can be set in steps of five minutes If set to zero the sleep timer is switched off Downloaded From TV Manual com Manuals 4 Press OK to switch on the sleep timer L gt TheTV switches to standby after the specified time Automatically switch the TV on on timer You can switch on the TV from standby to a specific channel at a specified time 1 Press amp MENU 2 Press AVP to select Setup gt Features gt On timer J Press to enter the On timer menu e Activate Selects how often the TV Is switched on e Time Sets the time to switch on the TV e Programme no Selects the channel or the connected device 4 Press amp MENU to exit Ea Select On timer gt Activate gt Off to disable this feature EN 19 English Use TV locks You can prevent your children from watching certain programmes or channels by locking the TV controls Set or change your PIN code 1 Press MENU 2 Press AVP to select Setup gt Features gt Set code Change code L gt The Set code Chang
49. remote control from the connected device to adjust the volume 34 EN Downloaded From TV Manual com Manuals Enable or disable EasyLink Do not enable Philips EasyLink if you do not intend to use it 1 Press amp MENU 2 Press AVP to select Setup gt Installation gt Preferences gt EasyLink J Select On or Off Use one touch play 1 After enabling EasyLink press play on your device L gt The TV automatically switches to the correct source Use one touch standby 1 Peso Standby On on the TV s or device s remote control The TV and all connected HDMI devices switch to standby Set TV speakers to EasyLink mode When you play content from an EasyLink compliant home theater the T V speakers are automatically muted 1 Enable one touch play and one touch standby between your Easylink compliant devices by following the instructions in the previous section see Enable or disable EasyLink on page 34 Press amp MENU Press AY 4b to select Setup gt Sound gt TV speakers gt Auto EasyLink L gt TheTV speakers are turned off automatically when content from an Easylink compliant system is detected UJ N 4 Press AVP to select Setup gt Sound gt TV speakers gt On to disable system audio control and enable the TV speakers To mute the TV speakers select TV speakers gt Off Use a Kensington lock There is a Kensington
50. rvices COMMON INTERFACE Downloaded From TV Manual com Manuals Access CAM services 1 After inserting and activating the CAM press ft MENU 2 Press AVP to select Setup gt Features gt Common interface L gt Applications provided by the digital TV service operator appear on the screen This menu option is available only if the CAM is inserted and activated correctly EN 33 English Use Philips EasyLink Your TV supports Philips EasyLink which uses the HDMI CEC Consumer Electronics Control protocol EasyLink compliant devices that are connected through HDMI connectors can be controlled by a single remote control The EasyLink compliant device must be switched on and selected as the source Philips does not guarantee 100 interoperability with all HDMI CEC devices EasyLink features One touch play When you connect your TV to devices that support one touch play you can control your TV and the devices with one remote control One touch standby When you connect your TV to devices that support standby you can use your TV remote control to put your TV and all connected HDMI devices in standby mode System audio control When you connect your TV to HDMI CEC compliant devices your TV can switch automatically to play audio from the connected device To use one touch audio you must map the audio input from the connected device to your TV You can use the
51. security slot at the back of the TV Prevent theft by looping a Kensington ock between the slot and a permanent object such as a heavy table yam Downloaded From TV Manual com Manuals EN 35 English 8 Product information Product information is subject to change without notice For detailed product information go to www philips com support Supported display resolutions Computer formats e Resolution refresh rate e 640 x 480 60Hz e 800 x 600 60Hz e 1024 x 768 60Hz e 1280 x 720 60Hz e 1280 x 768 60Hz e 1280 x 1024 60 Hz e 1360 x 768 60Hz e 1440 x 900 60Hz For Full HD only e 1680 x 1050 60Hz For Full HD only Video formats e Resolution refresh rate e 480i 60Hz 480p 60Hz e 576i 50Hz e 576p 50Hz e 720p 50Hz 60Hz e 1080 50Hz 60Hz e 1080p 24Hz 25Hz 30Hz 50Hz 60Hz 36 EN Downloaded From TV Manual com Manuals Multimedia e Supported storage device USB Only FAT or FAT 32 USB storage devices are supported Supported multimedia file formats Images JPEG Audio MP3 e Multimedia file names must not exceed 128 characters Tuner Reception Transmission e Aerial input 75 ohm coaxial IEC75 e DVB DVB Terrestrial DVB T MPEG4 e V system DVB COFDM 2K 8K PAL B G D K SECAM B G D K L L e Video playback NTSC SECAM PAL e uner Bands Hyperband S channel UHF VHF Remote control
52. ss OK to update the TV software manually J Follow the on screen instructions to complete the update The TV restarts after the software update is complete 24 EN Downloaded From TV Manual com Manuals Update using OAD 1 f using DVB T digital broadcast your TV automatically receives software updates If you receive a message on your screen asking you to update your software e Select Update now to update the software immediately Select Remind me later to exit the update screen at that time and be reminded later e Select Cancel to skip the update 2 f you select Cancel you can manually access the OAD update by selecting Setup gt Software update gt Local updates gt OAD Select the available version of OAD and press OK 4 Follow the on screen instructions to start the update The TV restarts after the software update is complete Change TV preferences Use the preferences menu to customise your TV settings 1 Press amp MENU 2 Select Setup gt Installation gt Preferences e Location Optimises TV settings for your location home or shop Volume bar Displays the volume bar when you adjust the volume e Channel info Displays information about the TV channel every time you switch channels Select Full to view channel information or Off to turn off the channel information e Universal access Enables or disables the univers
53. st you can only select those channels in the list see Select a favourite list on page 16 Switch channels with the channel grid The channel grid allows you to view all available channels in a grid format sernu smm e A x 9 e x L2 a eee Fa eames 1 Press OK L gt The channel grid appears 2 Press AY 4b to select and preview a channel 3 Press OK to watch the selected channel EN 9 English Watch connected devices Switch on the device before selecting it as a source on the TV Use the source button MENU FORMAT INCR SURR MHEG Ces C1 E fon DEMO SUBTITLE AD Sass 1 Press SOURCE L gt The source list appears 2 Press AY to select a device Press OK to confirm your choice L gt The TV switches to the selected device Adjust TV volume a iaj HL To increase or decrease volume e Press 4 To mute or unmute sound e Press X to mute the sound e Press again to restore the sound 10 EN Downloaded From TV Manual com Manuals Use teletext MENU FORMAT INCR SURR MHEG Ces Ce ees gu DEMO SUBTE AD mm m amp 1 Press MHEG TELETEXT L gt The main index page appears 2 Selecta page as follows e Press the Numeric buttons to enter a page number e Press P to view the next or previous page e Press the C
54. void of warranty Never attempt to repair the TV yourself e Use the TV and accessories only as intended by the manufacturer e The caution sign printed on the back of the TV indicates risk of electric shock Never remove the TV cover Always contact Philips Customer Support for service or repairs PA AL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION ADVERTENCIA NO ABRIR RIESGO DE CHOQUE ELECTRICO e Any operation expressly prohibited in this manual or any adjustments and assembly procedures not recommended or authorised in this manual shall void the warranty 2 EN Downloaded From TV Manual com Manuals Pixel characteristics This LCD product has a high number of colour pixels Although it has effective pixels of 99 99976 or more black dots or bright points of light red green or blue may appear constantly on the screen This is a structural property of the display within common industry standards and is not a malfunction Compliance with EMF Koninklijke Philips Electronics N V manufactures and sells many products targeted at consumers which like any electronic apparatus in general have the ability to emit and receive electromagnetic signals One of Philips leading Business Principles is to take all necessary health and safety measures for our products to comply with all applicable legal requirements and to stay well within the EMF stand
55. witch the TV off and on again for the change to take effect f you use P on your remote control to switch between channels the locked channels are skipped f you access the locked channels from the channel grid you are prompted to enter your PIN code Set parental ratings Some digital broadcasters rate their programmes according to age You can set your TV to display only programmes with age ratings higher than your child s age 1 Press amp MENU 2 Press AVP to select Setup gt Features gt Parental rating L gt A code setup screen appears J Enter your code using Numeric buttons L gt The parental rating menu appears Press AY to select an age rating Press OK to confirm Press f MENU to exit ON Ui 4 Use subtitles You can enable subtitles for each TV channel Subtitles are broadcast via teletext or DVB T digital broadcasts With digital broadcasts you can select a subtitle language Enable subtitles on analogue TV channels Select an analogue TV channel Press MHEG TELETEXT Enter the three digit page number of the subtitle page with the Numeric buttons Press MHEG TELETEXT to switch off teletext Press SUBTITLE L gt The Subtitle mode menu appears On U A WN Select On to display subtitles always or On during mute to display subtitles only when audio is muted Press OK to enable subtitles Oo NI Repeat this procedure to enable subtitles on each an
Download Pdf Manuals
Related Search