INSTALLATION INSTRUCTIONS FOR XLERATOR® HAND DRYER
Contents
1. the defect and within a reasonable time the Manufacturer shall send a suitable replacement part to remedy said defect and Owner shall be charged for said part at the current price level The Owner may return the defective part to the Manufacturer postage prepaid along with the serial number of the defective product and the Manufacturer will then issue to the Owner a full credit for the repair part including outgoing postage Said remedy is available only within five 5 years from the date of original shipment of the product from the Manufacturer s factory in East Longmeadow Massachusetts and provided further that said defect is not due to faulty installation accident misuse or vandalism Any implied warranties of merchantability or fitness for a particular purpose are hereby limited to the duration of the express written warranty contained in paragraph one 1 namely five 5 years from the date of shipment from the Manufacturer s factory in East Longmeadow Massachusetts There are no other warranties and remedies except as contained herein This warranty shall inure to the benefit of the Owners Successors and Assigns XleratorManual3 11 doc2. XL INSTALLATION INSTRUCTIONS FOR XLERATORe HAND DRYER FOR PROPER ELECTRICAL CONNECTIONS CHECK YOUR LOCAL BUILDING CODES YOUR UNIT MUST BE INSTALLED BY A QUALIFIED LICENSED ELECTRICIAN 11 13 32 R 290mm k 8H 210mm 4178 Suggested Mtg Heights from floor 6 11 16 to bottom of dryer a 170mm 105mm z Men s 45 1143 mm ed i Ladies 43 1 092 mm 5 3 32 S 10 E E Teenagers 41 1041 mm 129mm 5 6 DIA 8mm 12 5 16 Sm Children 35 889 mm i game ioten Handicapped 37 940 mm 4 crosman Sa t ie SS 4 ELECTRICAL INLETS gt ron IF MOUNTING OVER COUNTERTOP DISTANCE FROM 103 16 G TA 22mm DIA ale COUNTER TO DRYER MUST BE 15 381mm MINIMUM pigs aan 9 9 16 Recommended Fastener 6 5 32 157mm Masonry Wall y2 expansion sleeve with 1 4 lag bolt via Hollow Wall 1 4 wing type through bolt Wooden Wall 14 lag screw with washer l daim 141mm LOCATION OF ADDED MTG HOLES FOR MORE SECURE INSTALLATION 9 241mm K 1 Remove cover of dryer by unscrewing two tamper proof bolts from the sides of the cover with the special wrench provided with each unit 2 Attach wall plate at the four corners to smooth wall In locations where vandalism is a concern use the two additional mounting holes shown Remove control assembly to access right side mounting hol
3. bead of silicone sealant be placed around the outside of the cover at the wall to protect dryer from internal corrosion caused by wash water and cleaning solutions PARTS LIST FOR XLERATOR DRYER Jj REF NO DESCRIPTION XL14 XL13 4 XL 1 Cover includes Nameplate XL8 XL12 4 t XL2 Nameplate XL6E XL3 Tamper proof Bolt XL 4 Tamper proof Wrench XL5 Air Outlet includes gasket XL 6 Terminal Block includes screws XL7 Control Assembly amp Sensor XL 8 Heating Element Assembly XL 9 Motor Assembly XL 10 Wall Plate Assembly XL 11 Cover Mounting Brackets XL 12 Housing Grommet XL 13 Housing Retainer XL 14 Recess Kit for ADA XL 15 Optics Assembly Sensor NOTE Model Serial Number and Voltage of the dryer MUST BE included when ordering parts XleratorManual3 11 doc A DISCONNECT ELECTRICAL SUPPLY TO DRYER PRIOR TO SERVICING M CLEANING INSTRUCTIONS OUTSIDE Gently wash cover including air Inlet holes using a soft cloth or sponge and a mild soap or detergent with lukewarm water to loosen dirt and grime INSIDE CLEANING SHOULD BE PERFORMED BY QUALIFIED SERVICE PERSONNEL With normal use dryer will require cleaning once a year Heavier usage requires more frequent cleaning Lint on the air inlet or other internal parts of dryer will reduce efficiency and shorten the life of the working parts To clean remove cover by unscrewing the tamper proof bolts from cover with the special wrench provided with each dry
4. e Attach with the recommended type of fastener see above 3 Connect a 110 120V dryer to a 15 Amp dedicated branch circuit using at least 12 GA copper wire Do not exceed a 20 Amp branch circuit Connect a 208 220 240V or 277V dryer to no more than a 15 Amp dedicated branch circuit using at least a 14 GA copper wire Attach lines to terminals as indicated by the schematic inside dryer cover Be sure that an equipment ground wire is securely fastened to green ground screw on base plate Dryers should be installed per local code requirements 4 In multiple installations before replacing cover check the Serial Number marked inside the dryer to be sure it matches the Serial Number marked on the label at the bottom of cover PLEASE DO NOT SWITCH COVERS Do not forget to leave the special TAMPER PROOF WRENCH with the owner INSTALLATION NOTE If the dryer will not turn on stays on or stops working it may be mounted too close to a counter or object Turn off the power to dryer for 10 seconds and then reapply power If dryer will start then turn off again relocate the object or remount dryer If this is not possible adjust the range of the sensor by turning the range adjustment on the control board counterclockwise to decrease sensor range Please call the factory at 1 800 255 9235 and one of our trained technicians will be happy to assist you NOTE Upon completing installation and checking for proper operation it is highly recommended that a
5. er Use a small soft brush to gently clean all parts TROUBLESHOOTING YOUR DRYER As with any electrical appliance repairs to be performed by qualified service personnel If your dryer does not turn on 1 Verify that the dryer is receiving power by checking electrical service circuit breaker or fuse to the dryer 2 Check voltage to dryer terminal block 3 Check RED service LED light for the following Light is ON Place hands under sensor If light stays on then replace sensor If light goes off check to make sure wiring is correct at dryer control If OK check motor fuse if so equipped and wire connecting to motor If both are OK replace motor Light is OFF Check for loose disconnected or improper wiring at dryer control See wiring schematic inside dryer cover or replace dryer control Light is FLASHING Dryer is in lockout mode See installation note If your dryer does not shut off 1 May be mounted too close to a counter or object See installation note 2 Check for loose disconnected or improper wiring at dryer control See wiring schematic inside dryer cover 3 Replace dryer control If your dryer heats up but no air comes out 1 Check motor fuse if so equipped 2 Check wire connection to motor 3 Replace motor If your dryer does not always turn on or turns on by itself 1 May be mounted too close to a counter or object See installation note 2 Check for foreign material on
6. optical sensor next to air outlet 3 Check for loose wires on dryer control 4 Replace dryer control If your dryer blows only cold air 1 Check for loose connections to heating element 2 Replace heating element If your dryer has a loss of air volume 1 Check for air leaks at the heating element or nozzle If leaking replace heating element or nozzle 2 Check for slow running motor or burning smell If so replace motor Note If the problem cannot be resolved with the above please call the factory at 1 800 255 9235 and one of our trained technicians will be happy to assist you 5 YEAR LIMITED WARRANTY This product is warranted to be free from defects for a period of five 5 years from the date of shipment from the Manufacturer s factory at 357 Chestnut St East Longmeadow Massachusetts 01028 shall have either one of the following remedies In the event of a breach of the warranty described above the Owner a The Owner shall return the defective product to the Manufacturer postage prepaid and the Manufacturer shall repair said product within a reasonable time and free of charge provided that said product is returned within five 5 years from the date of original shipment from the Manufacturer s factory in East Longmeadow Massachusetts and provided further that said defect is not due to faulty installation accident misuse or vandalism or b The Owner may notify the Manufacturer by telephone or in writing of
Download Pdf Manuals
Related Search