Instruction Manual
Contents
1. m WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE DO NOT OPEN THE CABINET REFER SERVICING TO QUALIFIED PERSONNEL ONLY CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUGWITHANEXTENSIONCORD RECEPTACLEOROTHEROUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE ATTENTION POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT 1 Read Instructions All the safety and operating instructions should be read before the appliance is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the appliance should be adhered to 4 Follow Instructions All operating and use instructions should be followed 5 Cleaning Unplug this appliance from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleansers Use a damp cloth for cleaning 6 Attachments Do not use attachments that are not recommended by the manufacturer or they may cause hazards 7 Water and Moisture Do not use this product near water for example near a bathtub wash bowl kitchen sink laundry tub in a wet basement or near a swimming pool and the like 8 Accessories2. AWG 1 0mm copper clad steel or bronze wire or larger as ground wire b Secure antenna lead in and ground wires to house with stand off insulators spaced from 4 feet 1 22m to 6 feet 1 83m apart c Mount antenna discharge unit as close as possible to where lead in enters house d A driven rod may be used as the grounding electrode where other types of electrode systems do not exist Refer to the National Electrical Code ANSI NFPA 70 1990 for information e Use jumper wire not smaller than No 6 AWG 13 3mm copper or equivalent when a separate antenna grounding electrode is used NOTE TO CATV SYSTEM INSTALLERS THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER S ATTENTION TO ARTICLE 820 40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND IN PARTICULAR SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL EXAMPLE OF ANTENNA GROUNDING ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING H CONDUCTORS NEC SECTION 810 21 ELECTRIC SERVICE EQUIPMENT GROUND CLAMPS POWER SERVICE GROUNDING al ELECTRODE SYSTEM NEC ART 250 PART H
3. Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the appliance 9 Ventilation This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Any slots or openings in the cabinet are provided for ventilation To ensure reliable operation of the product and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface 10 Grounding or Polarization This product is equipped with a 3 wire line cord receptacle It is intended for use with a 3 wire properly grounded power socket Do not defeat the safety purpose of the supplied line cord and plug 10A Mise a la terre ou Polarisation Cet appareil est quip avec un cordon d alimentation a trois fils Il est a brancher sur une prise ayant un connecteur ala terre Assurez vous que la connection a la terre ne manque pas 11 Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your appliance dealer or local power company 12 Power co
4. AKE COMPANY 230 INDUSTRIAL DRIVE FRANKLIN OHIO 45005 U S A CUSTOMER SERVICE AND PARTS TELEPHONE 1 937 746 6990 TELEFAX 1 937 743 4576 WORLD WIDE WEB SITE http www rldrake com POWER SUPPLY PS8 Cy DC OUTPUTS X 8 12V GND5V 100 240 V 50 60 Hz 80 WATTS DC OUTPUT RATING TOTAL OF ALL OUTPUTS 5 V 4 75 A MAX 12 V 3 0 A MAX TM is a trademark of the R L Drake Company Copyright 2001 R L Drake Co P N 3852376B 5 2001 Printed in the U S A Important Safeguards WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK DO NOT EXPOSE TO RAIN OR MOISTURE iWARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE POWER SUPPLY COVERS NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance
5. DRAKE PS8 Power Supply GENERAL Power Requirements 100 VAC to 240 VAC and 10 10 of end limits Frequency 50 60 Hz AC Input Power 80 WATTS Operating Temperature Range 0 to 50 C Internally Mounted 50 mm Axial Fan 12 VDC 140 mA 12 CFM ft min Output Voltages 5 VDC 4 75 Amps maximum 12 VDC 3 Amps maximum MECHANICAL Dimensions WxHxD 4 2 in x3 5in x 9 4 in 10 7 cm x 8 9 cm x 23 9 cm Weight 2 6 lbs 1 2 Kg CONNECTORS AC Input IEC DC Output Mini Fit JR x 8 Fuse Internal AC input 2A 250 V SLO BLO 5 x 20 mm Power supply assembly employs short circuit and over voltage protection ACCESSORY SUPPLIED AC Power Cord 6 Ft IEC USA PS8 Rear Panel Connections Both the AC input receptacle and DC output connector are located on the rear panel of the power supply module 1 AC Input The power supply accepts standard 100 to 240 VAC 50 60 Hz inputs and 10 10 of that voltage range 2 DC Output The polarized Mini Fit JR connector provides 8 sets of 12 VDC 5 VDC and Ground connection cables for the compatible digital rack units DRAKE R L DR
6. rd Protection Power supply cords should be routed so they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance 13 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet 14 Power Lines An outside antenna system should not be located in the vicinity of overhead power lines other electric light or power circuits where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them may be fatal 15 Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock 16 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 17 Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 18 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to q
7. ualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions An improper adjustment may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or the cabinet has been damaged f When the product exhibits a distinct change in performance this indicates a need for service 19 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original parts Unauthorized substitutes may result in fire electric shock or other hazards 20 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition 21 Outdoor Antenna Grounding Before attempting to install this product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges a Use No 10 AWG 5 3mm copper No 8 AWG 8 4mm aluminum No 17
Download Pdf Manuals
Related Search