Pro-Ject RPM 3 Carbon User Guide
Contents
1. INSTRUCTIONS FOR USE Pro Ject RPM 3 Carbon 2 Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29 Controls features and connections 1 11 2 10 12 13 14 Power switch motor unit with stepped drive pulley Drive belt Platter Tonearm counterweight Tonearm lift lever Tonearm rest and removable transport lock Tonearm tube Power supply socket Phono output sockets and earth connection Magnetic anti skating mechanism Magnetic anti skating scale Magnetic anti skating adjustment mechanism Headshell with finger lift Connection cable not shown Power supply not shown Stylus pressure gauge white plastic instrument with mN scale not shown Hexagonal key not shown Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29 3 Pro Ject RPM 3 Carbon Dear music lover thank you for purchasing a Pro Ject Audio Systems record player In order to achieve maximum performance and reliability with this record player you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse EN Important notice The record player is supplied without cartridge or with a factory fitted and adjusted cartridge Ortofon 2M SILVER The following instructions for adjusting the cartridge are provided in case the cartridge is mounted turntable was supplied without cartridge2. c Downforce 2 3g Anti skating force 2 3g a b c Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29 5 Connection to the amplifier The record player has gold plated female RCA phono sockets 9 for connection to the amplifier using the supplied interconnect cables Use the Phono input sometimes labelled gram disc or RIAA on your amplifier Make sure that the phono input offers correct matching and amplification for the type of cartridge used Line inputs such as CD Tuner Tape or Video are not suitable Take care to connect the left and right channels correctly The right channel is usually marked red the left channel black or white Check the manual supplied with your amplifier for relevant information An earthing wire may be connected to the screw terminal between the sockets if you encounter hum problems when using the record player If your amplifier does not have an input suitable for phono cartridges you will require a separate phono amplifier stage for MM or MC cartridges which is then connected between the record player and a free line level input of the amplifier For detailed product information regarding Pro Ject Audio interconnect cables and phono amplifiers please refer to the Pro Ject web site www project audio com E The recommended load impedance for the factory fitted cartridge is 47kohms MM input Mains power co
3. or is replaced by a different model at a later date During assembly and adjustment of the deck small parts could be lost if not carefully placed in a suitable receptacle Before starting assembly make yourself acquainted with the parts listed above and correspondingly numbered in the technical drawings above Separately packed items are marked with an asterisk Set up Make sure the surface you wish to use the turntable on is level use a spirit level before placing the turntable on it After putting the motor unit in place fit the drive belt 2 around the platter 3 and the smaller diameter part of the motor pulley 1 Avoid getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt s lifespan Use absorbent kitchen paper to remove any oil or grease from the outer edge of the platter and the belt Remove the transport lock 16 from the tonearm Store it in the original packaging so they are available for any future transportation Cartridge downforce adjustment The counterweight 4 supplied is suitable for cartridges weighing between 5 12g counterweight no 82 Adjust the downforce prior to setting the anti skating force Place counterweight 4 halfway along the counterweight support rod at rear of arm being sure to have the securing screw uppermost Remove the felt mat With the power off and the platter static place the stylus pressure gauge onto the platter To set the recommended
4. 18mN downforce 1mN 0 19 0 1 Pond place the tip of the stylus exactly in between the two points marked 15mN and 20mN If the stylus gauge becomes level then the correct pressure has been achieved However if the there is insufficient or excessive pressure the gauge will either not move or tilt down To adjust the amount of pressure carefully move the counterweight 4 along the support rod until the stylus pressure is sufficient to raise the pressure gauge to the level position Moving the counterweight 4 away from the cartridge will reduce pressure and towards will increase pressure Finally secure the counterweight 4 using hexagonal key provided ES Please note It is advised to remove stylus tip from gauge whilst making adjustments to avoid damage to stylus 4 O Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29 Adjusting the vertical tracking angle vta Put a record on the platter When the needle is lowered into the record groove and the tonearm is not resting on the lift arm the tube of the tonearm should be parallel to the surface of the record If it is not loosen both screws in the tonearm base just enough to allow vertical movement of the arm pillar without force and slide the arm up or down until it is parallel Carefully retighten the screws without applying excessive force which would deform the arm pillar finger tight is quite sufficient Adjusting the azimuth
5. The cartridge needle must be vertical in the record groove in order to trace the es i PA N groove wall modulations correctly pa EY A small screw at the bearing end of the arm allows incorrect azimuth to be Eve corrected if your needle is not mounted exactly perpendicular to the cartridge LA oll La W Ne body which is often the case Ss FRY CALAS Slacken off the screw just enough to be able to revolve the arm tube without NI pee applying force Please note do not remove the screw completely AN screw With the aid of a good magnifying glass adjust the needle until it is vertical in the groove i e perpendicular to the record s surface Ideally this should correspond to the top surface of the cartridge body being parallel to the record surface When you are satisfied that the needle is vertical retighten the screw carefully Under no circumstances should the arm tube be adjusted with the needle still in the record groove Irreparable damage may be caused to the cantilever suspension The arm must be lifted to make each adjustment and lowered afterwards to check it Anti skating force adjustment The anti skating force must be adjusted corresponding to the downforce The anti skating mechanism is calibrated from 0 to 5g The anti skating force should correspond with the downforce Three examples of magnetic anti skating mechanism a Downforce 1 5g Anti skating force 1 5g b Downforce 1 7g Anti skating force 1 7g
6. ification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights ofthe customer PRO JECT is a Registered Trademark of H The information was correct at the time of going Lichtenegger to press The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development This guide was produced by Pro Ject Audio Systems Copyright 2015 All rights reserved Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29 9 Accessories j e Instruction for use Felt Mat Tonearm transport lock Platter Mk CSL A Power supply Motor ID Platter housing cover 10 Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29
7. nical specifications Pro Ject RPM 3 Carbon Pro Ject 10s Carbon Nominal speeds Speed variance Wow and flutter Signal to noise Effective tonearm mass Effective tonearm length Overhang Power consumption Outboard power supply Dimensions W x H x D Weight 33 45 r p m 33 0 14 45 0 11 33 0 19 45 0 08 71dB 15g 10 254mm 16mm 5 W max lt 0 5W standby 15V DC 800mA universal power supply 447 x 118 x 373mm 5 5 kg net 8 Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29 Potential incorrect use and fault conditions Pro Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances Therefore the following list of common fault symptoms is included The platter doesn t turn although the unit is switched on The unit is not connected to the mains power supply No mains at the socket Drive belt is not fitted or has slipped off No signal through one or other channel or both channels No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier This could be due to a faulty plug broken wire or solder joint or simply loose plug socket connection Pho
8. nnection The turntable is supplied with the universal power supply with 3 exchangeable sockets adapters suitable for all countries Select the correct adapter for your country and insert the adapter to the exchangeable part of the power supply Connect the low voltage plug from the power supply to the socket 8 on the rear of the record player before connecting the power supply to the mains Switching on and off Pressing the power switch 1 alternately starts or stops the motor 6 Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29 Changing replay speed Put the belt 2 over the larger diameter part of the motor pulley 11 To revert to 33 r p m repeat the proceedings using the smaller step on the pulley 5 For detailed product information please refer to the Pro Ject web site www project audio com Maintenance and cleaning Your record player requires little or no regular maintenance Remove dust with a slightly moistened antistatic cloth Never use a dry cloth because this will create static electricity which attract more dust Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching Always disconnect the reco
9. no input not selected at amplifier Amplifier not switched on Amplifier or speakers defective or muted No connection to the loudspeakers Strong hum on phono input No earth connection from cartridge or arm or arm cable to amplifier or earth loop Distorted or inconsistent sound from one or both channels Record player is connected to wrong input of amplifier or MM MC switch incorrectly set Needle or cantilever damaged Wrong r p m drive belt overstretched or dirty platter bearing without oil dirty or damaged Service Should you encounter a problem which you are not able to alleviate or identify despite the above information please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Guarantee repairs will only be effected if the unit is returned correctly packaged For this reason we recommend keeping the original packaging Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide Fit the cartridge protection cap Insert the transport lock for the tonearm 16 prior to carefully packaging the record player Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these 5 instructions for use and or by transportation without the original packaging Mod
10. rd player from the mains power supply as a precaution before maintenance Fitting and connecting the cartridge All cartridges with half inch mounting holes can be fitted Leaving the needle s protection cover on fit the cartridge to the headshell using the screws supplied with the cartridge by passing one screw through each slot in the headshell 14 Do not tighten the nuts yet Connect the tonearm wires to the cartridge pins as follows white left channel positive L red right channel pos R green right channel return R blue left channel return L The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted Particular tools like the Pro Ject Alignment Tool are required to accomplish this job properly If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of your Pro Ject dealer to accomplish this task for you Please note adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging the cartridge or tonearm bearings Leave this work to your dealer if you are in any way unsure of the necessary steps and precautions to be taken Useful tips The record player should be positioned on a low resonance surface such as wood or multiple layer ply board to avoid structural vibrations disturbing replay O Pro Ject Audio Systems Pro Ject RPM 3 Carbon Ortofon 2M SILVER Revision 2015 01 29 7 Tech
Download Pdf Manuals
Related Search