Bosch Dishwasher SMS68M22AU User Manual
Contents
1. 3 To raise the basket hold the basket on the sides of the upper edge and lift it up 4 Before re inserting the basket again ensure that it is at the same height on both sides Otherwise the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit Detergent You can use tablets as well as powder or liquid detergents for dishwashers but never use washing up liquid The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling Tablets contain an adequately large amount of active ingredients for all cleaning tasks Modern powerful detergents predominantly use a low alkaline formulation with phosphate and enzymes Phosphates bond the lime in the water Enzymes break down starch and remove protein Phosphate free detergents are less frequent These have a slightly weaker lime bonding capacity and require a higher dosage To remove coloured stains e g tea tomato sauce oxygen based bleaching agents are usually used Note To ensure a good washing result always follow the instructions on the detergent packaging If you have further questions we recommend that you contact the detergent manufacturers helpline A Warning Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents Adding detergent 1 If the detergent dispenser is still cl2. of the detergent e quick or short is not reached in the selected short programme Washing effect and dissolving performance are reduced after a prolonged storage time or detergent is very lumpy Droplet formation on plastic surface is physically unavoidable After drying water stains are visible Fault what to do aus Remedial action Arrange utensils with adequate clearance between them ensuring that the spray jets can reach the surface of the utensils Prevent contact points Arrange utensils so that the spray arm can rotate without obstruction Clean the spray arm nozzles See Cleaning and maintenance Clean filters see Cleaning and maintenance Insert and engage filters correctly Select a more intensive rinse programme Do not prerinse utensils Remove only large food remnants Do not place hollow receptacles too obliquely and do not place in the corner area Set top basket to same height using side levers Detergent dispenser cover must not be obstructed by utensils Do not place utensils or fragrance dispenser in the tablet collecting tray Tablet must be inserted flat and not upright Dissolving time of tablets too long for a quick or short programme Use a detergent powder or select a more intensive programme Change detergent Use a more intensive programme more water changes Arrange utensils in a sloping position Use rinse aid
3. 6 Pull out the appliance carefully pulling the hose behind Transportation Empty the dishwasher and secure loose parts Drain the appliance according to the following steps 1 Turn on the tap 2 Close the door 3 Switch on ON OFF switch 1 4 Select programme with the highest temperature The expected programme duration is indicated on the numerical display 10 5 Press START button 8 Programme sequence starts 6 After approx 4 minutes press the START button until I i is indicated on the digital display After approx 1 min amp 27 is indicated on the digital display 7 Switch off ON OFF switch 1 8 Turn off the tap disconnect supply hose and drain water Transport appliance upright only This prevents residual water from running into the machine control and damaging the programme sequence Subject to changes 34 Childproof lock door lock A Warning 40 Activate the childproof lock Always close the appliance door completely 41 Open the door with activated when you leave the appliance childproof lock This is the only way you can protect your 42 Deactivate childproof lock children from potential dangers Baking sheet spray head gourmet plates pasta plates dinner plates can be cleaned with the aid of the spray head To do this remove the top basket and insert the spray head as illustrated in the dia
4. obstruction 29 aus Fault what to do Fault Cover on the detergent dispenser cannot be closed Detergent residue in the detergent dispenser or in the tablet collecting tray Appliance stops in the programme or programme is interrupted Filling valves making striking noises Knocking or rattling noise Unusual foam formation 30 Cause Detergent dispenser or cover guide blocked by sticky detergent residue Spray arms blocked by utensils therefore detergent is not rinsed out The detergent dispenser was damp when filled Door not closed properly Do not place utensils or fragrance dispenser in the tablet collecting tray Top basket presses against inner door and prevents door from being closed securely Power and or water supply interrupted Depends on domestic installation as appliance is not defective No effect on appliance function Spray arm strikes the utensils utensils not positioned correctly If there is a low load the water jets strike the washing tank directly Light utensils move during the wash cycle Handwash liquid in the rinse aid dispenser Rinse aid spilled Remedial action Remove detergent residue Ensure that the spray arms can rotate freely Pour detergent into the dry detergent dispenser only Close the door Check whether rear panel is being pressed in e g by socket or by hose holder which has not been
5. the home environment Use the dishwasher only in the household and only for its designed purpose for washing domestic dishes Safety instructions Children from 8 years of age or people whose physical sensory or mental abilities or their lack of experience or knowledge prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person Before you switch ON the appliance Please read the operating and installation instructions carefully They contain important information on how to install use and maintain the appliance Retain all documents for subsequent use or for the next owner Delivery 1 Check the packaging and dishwasher immediately for damage caused in transit Do not switch on a damaged appliance but contact your supplier Please dispose of the packaging material in an environmentally friendly manner Do not let children play with packaging and its parts There is a risk of suffocation from collapsible boxes and film Installation Following installation ensure that the back of the dishwasher is not freely accessible protection against contact due to hot surface Install and connect the appliance according to the installation and assembly instructions Prior to installation disconnect the dishwasher from the power supply Ensure that the protective conductor system of the domestic suppl
6. 27 aus Fault what to do Fault Cause Washable or water soluble Detergent subs ances are Remedial action Change detergent brand coatings in the containeror deposited These coatings cannot Clean appliance mechanically on the door chemicals app usually be removed with iance cleaner Only for glasses Initial glass corrosion can be wiped off White stubborn coatings Detergent subs limescale on the utensils container or door chemicals app Underdosing of Too weak rinse selected Tea or lipstick residue on Too low rinsing the utensils only apparently ances are deposited These coatings cannot usually be removed with ance cleaner detergent programme emperature Too little or unsuitable detergent Utensils precleaned too intensely sensors therefore decide on weak programme sequence Stubborn soiling cannot be completely removed Coloured blue yellow Film formation consisting brown difficult to remove of ingredients from vegetables to nonremovable coatings e g cabbage celery potatoes in the appliance or on noodles or the tap water e g stainless steel utensils manganese Film formation caused by metallic components on silver or aluminium utensils Plastic parts discoloured Too low rinsing temperature QVZ Utensils precleaned too intensely sensors therefore decide on eak programme sequence ubborn soiling can
7. hygienic regularly clean it with a damp cloth and a little washing up liquid lf the appliance is switched off for a prolonged period leave the door ajar to prevent the formation of an unpleasant odour Never use a steam cleaner to clean your dishwasher The manufacturer is not liable for any consequential damage Regularly wipe the front of the appliance and fascia with a damp cloth water and a little washing up liquid are adequate Do not use sponges with a rough surface or abrasive detergents as these could scratch the surfaces Stainless steel appliances To prevent corrosion avoid using sponge cloths or wash them out thoroughly several times before using for the first time 21 aus Cleaning and maintenance A Warning Health hazard Never use other domestic detergents e g containing chlorine Rinse aid Check the refill indicator 4 _ If required refill rinse aid Filters The filters keep large foreign objects in the rinsing water away from the pump These foreign objects may occasionally block the filters The filter system consists of a coarse filter a flat fine filter and a microfilter 1 After each washing cycle check the filters for residue 2 Unscrew filter cylinder as illustrated and take out filter system 22 3 Remove any residue and clean filters under running water 4 Re install filter system in reverse sequence and e
8. removed Restore power and or water supply No remedial action possible Position utensils so that the spray arms do not strike the utensils Load the appliance with more utensils or distribute the utensils more evenly in the dishwasher Arrange light utensils securely Immediately refill rinse aid dispenser with rinse aid Remove rinse aid with a cloth Customer service If you are unable to rectify the fault please contact your customer service We always find a suitable solution even to avoid unnecessary visits by technicians Contact information for your nearest customer service can be found on the back of these instructions for use or on the enclosed customer service list When calling please state the appliance number E Nr 1 and the production number FD 2 which can be found on the rating plate 31 on the appliance door Rely on the competence of the manufa cturer Contact us You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your domestic appliances Customer service aus Installation and connection The dishwasher must be connected correctly otherwise it will not function properly The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragraphs or in the installation i
9. tablets may not have full cleaning effect due to different dissolving properties and there may even be undissolved detergent residue It is recommended to use washing powder for these programmes m The Intensive programme on some models requires one tab only When using washing powder you can apply some of this cleaning agent to the inside of the appliance s door If using detergents in a water soluble protective cover Take hold of the cover with dry hands only and put the detergent into an absolutely dry detergent dispenser only otherwise the detergent may stick If you switch from combined detergents to solo detergents ensure that the water softening system and amount of rinse aid have been set to the correct value 15 aus Overview of programmes Overview of programmes The max possible number of programmes is illustrated in this overview The corresponding programmes for your appliance can be found on the fascia The programme data has been measured in the laboratory according to AS NSZ 2007 Typeof utensils Programm and soiling Pots utensils and cutlery Highly soiled my r Pots and Pans 70 Programme sequence Prerinse Clean 70 Intermediate rinse Final rinse 70 Dry 1 1 30 2 40 Utensils and cutlery Normally soiled auto UW Auto 45 65 v eco Eco 45 Is optimised according o the soiling with the aid of sensors Prerinse ean 45 ntermed
10. the door carefully when the programme is still running There is a risk of hot water spraying out of the appliance aus Safety instructions A Warning s Risks to children f fitted use the childproof lock An exact description can be found in the back of the enve lope Do not allow children to play with or operate the appliance Keep children away from detergents and rinse aid These may cause chemical burns in the mouth throat and eyes or asphyxiation Keep children away from open dishwasher The water in the rinsing compartment is not drinking water and could contain detergent residue Ensure that children do not place fingers in the tablet collecting tray 24 Small fingers could become caught in the slots When opening and closing the door on an eye level appliance ensure that children do not become jammed or crushed between the appliance door and the cupboard door below Children could become locked in the appliance danger of suffocation or get into another dangerous situation Redundant appliances Pull out the mains plug sever and dispose of the power cord Destroy the door lock so that the door can no longer be closed Protection of the environment Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials Please dispose of the individual parts separated according to type Please ask your dealer or i
11. 5 Bottom spray arm 26 Filters 27 Bottom basket 28 Dispenser for rinse aid 29 Detergent dispenser 30 Lock for detergent dispenser 31 Rating plate depending on model aus Rinse aid Overview of menu The settings can be found in the individual chapters g Intensive drying 2 00 d0 i r Rinse aid r A 05 F Automatic disconnection P 90 P E As soon as the rinse aid refill indicator is lit on the fascia there is still a rinse aid reserve of 1 2 rinsing processes Refill with rinse aid The rinse aid is required for stain free utensils and clear glasses Use only rinse aid for domestic dishwashers Combined detergents with rinse aid component may be used up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol l only If the water hardness is over 21 dH rinse aid must be used 1 Open the dispenser by pressing and lifting the plate on the cover 2 Carefully pour rinse aid up to the max mark in the filler opening 3 Close cover until it clicks shut 4 To prevent excessive foam formation during the next rinse cycle remove any rinse aid which has run over with a cloth Setting amount of rinse aid The amount of rinse aid can be set from ru to rl Please set rinse aid on 05 to obtain very good drying results 75 is already set in factory Change this setting only if streaks select lower setting or water stains select higher setting ar
12. Register your new Bosch now www bosch home com welcome Dishwasher Zu BOSCH aus Instruction manual Table of contents Intended use 4 Safety instructions 4 Before you switch ON the appliance 4 Delivery ns alas san 5 Installations kaso a et 5 Mdai US EL ad russ a heen ats 6 DOONOCK ara aaa ash 6 Button lock tn cea a ea 6 Damage teenie ana nen Den 7 Disposal rs rk sea er 7 Protection of the environment 9 P ckaging 24 4 Da ow deen er 9 Old appliances 9 Getting to know your appliance 9 Control panel 9 Appliance interior 9 Overview of menu 10 Ea Rinse aid 4 4 4342 10 Setting amount of rinse aid 10 Switching off rinse aid refill MACAO cok detent os ar sn 11 Utensils 22 00 03 11 Not suitable 05 11 Glass and utensil damage 11 Loading the dishwasher 12 Unloading the dishwasher 12 Cups and glasses 12 PANS teehee are 12 Cutlery drawer 13 Folding spikes 13 Small accessories holder 13 Adjusting the height of the basket 14 aus Detergent 06 14 Adding detergent 15 Overview of programmes 16 Programme selection 17 Information for test institutes 17 Additional options 18 Express Wash Speed Perfect VarioSpeed 22222222 18 Ha
13. ater pump is not locked in position Mains voltage too low he mains plug Turn off the tap Unscrew water connection ean filter in the supply hose Screw water onnection on again Check for leaks econnect power supply Switch on e appliance ean filters See Cleaning and maintenance nstall hose without kinks remove any esidue Check connection to siphon and open if equired Lock cover correctly See Waste water pump Clean pump and lock cover correctly See Waste water pump ao OS Not an appliance fault have the mains voltage and electrical installation checked Fault A different error code is indicated on the digital display Eg to 32 Display flashes Refill indicator for rinse aid 4 lis lit Refill indicator for rinse aid 4 lis not lit Water is left in the appliance at the end of the programme Cause A technical fault has probably occurred Door not closed properly No rinse aid Refill indicator switched off There is still enough rinse aid available Filter system or area under the filters 26 is blocked The programme has not yet ended Fault what to do aus Remedial action Switch off appliances with the ON OFF switch L_1_ After a short time restart the appliance If the problem recurs turn off the tap and pull out the mains plug Call customer service and mention the error code Close the door Ensu
14. d down programme button and press START button until d Q is indicated on the digital display 4 Release both buttons 5 Keep pressing programme button until the value Pi is indicated on the numerical display 10 N 20 To change the setting 1 Press programme button LC Each time the button is pressed the set value increases by one level when the value of 7 02 has been reached the display jumps back tor Pag 2 Press START button 8 The set value is saved Switching off the appliance Short time after the end of the programme 1 Switch off ON OFF switch 1 2 Turn off the tap not applicable if Aqua Stop fitted 3 Open the door 4 Remove the utensils when they have cooled down Note When the programme ends leave the appliance to cool down a while before opening it This will prevent steam from escaping and causing long term damage to your built in furniture Interrupting the programme 1 Switch off ON OFF switch 1 The LEDs go out The programme is saved If the door was opened on an appliance which has a warm water connection or is heated first leave the door ajar for several minutes and then close Otherwise expansion pressure may cause the appliance door to spring open or water to run out of the appliance 2 To continue the programme switch on the ON OFF switch again Terminating the programme Reset 1 Press START button for approx 3 sec The numerica
15. d glass production process m Chemical composition of the detergent Water temperature of the wash programme Recommendation Use only glasses and porcelain which the manufacturer designates as dishwasher proof m Use a detergent which protects utensils m Take glass and cutlery out of the dishwasher as soon as possible after the programme ends 11 aus Utensils Loading the dishwasher 1 Remove large food remnants It is not necessary to prerinse utensils under running water 2 Place the utensils so that they are secure and cannot tip over all utensils with their openings face down parts with curves or indentations are at an angle thereby allowing water to drain does not obstruct rotation of the two spray arms and 25 Very small utensils should not be washed in the machine as they may fall out of the baskets Unloading the dishwasher To prevent water from dripping off the upper basket onto the utensils in the lower basket it is recommended to empty the appliance from the bottom up Hot utensils are sensitive to shock Therefore when the programme ends leave the utensils to cool down in the dishwasher until they can be handled Note When the programme ends water droplets can still be seen inside the appliance This does not affect the drying of the utensils Cups and glasses Top basket Pans Bottom basket Ti
16. dditional options can be set with the buttons L7 G Express Wash Speed Perfect VarioSpeed This function can reduce the running time by approx 20 to 50 depending on the selected rinse programme The change in the running time is indicated on the digital display 10 To obtain optimum cleaning results at a reduced running time water and energy consumption are increased Half load If you have only a few items to wash e g glasses cups plates you can switch to half load This will save water energy and time It is recommended to put a little less detergent in the detergent dispenser than for a full load a HygienePlus This function increases the temperatures and retains them for an extra long time to obtain a defined disinfection performance Continuous use of this function increases the hygiene status This additional option is ideal for cleaning e g chopping boards and baby bottles Intensive zone Perfect for a mixed load You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket The spray pressure in the lower basket is intensified the rinsing temperature is increased slightly Extra drying An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better There is a slight increase in the energy consumption Operating the appliance Aqua sensor depending o
17. e near heat sources radiators heat storage tanks cookers or other appliances which generate heat and do not install under a hob After installing the appliance ensure that the plug is easily accessible See Electrical connection Some models The plastic housing on the water connection contains an electric valve the connecting cables are in the supply hose Do not cut through this hose do not immerse the plastic housing in water In daily use Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents Childproof lock door lock The description of the childproof lock is at the back in the envelope depending on model Childproof lock button lock You can secure your appliance from being unintentionally the programme terminated e g improper operation by children Activating the button lock 1 Start the required programme 2 Hold down the button for approx 4 sec until this L is indicated on the digital display If any button is pressed while the programme is running this LL is indicated on the digital display It is not possible to end Reset the programme Deactivating the button lock Hold down the button for approx 4 sec until the display Li goes out When the programme ends Ai on the digital display the button lock is cancelled Ifthere is a power failure the button lock is retained Whenever a prog
18. e left on the utensils 1 Close the door 2 Switch on ON OFF switch 1 3 Hold down programme button and press START button until du is indicated on the digital display 4 Release both buttons 5 Press programme button until the factory set value r 05 is indicated on the digital display 10 To change the setting 1 Press programme button LC Each time the button is pressed the set value increases by one level when the value of 7 76 has been reached the display jumps back to r D off 2 Press START button 8 The set value is saved Switching off rinse aid refill indicator If the rinse aid refill indicator is impaired e g when using combined detergents containing rinse aid component it can be switched off m Proceed as described under Setting amount of rinse aid and set the value to ru The rinse aid refill indicator is now switched off Utensils aus Utensils Not suitable Cutlery and utensils made of wood Delicate decorative glasses craft and antique utensils These decors are not dishwasher proof Plastic parts not resistant to heat Copper and tin utensils a Utensils which are soiled with ash wax lubricating grease or ink Aluminium and silver parts have a tendency to discolour and fade during the wash cycle Even some types of glass e g crystal glass objects may turn cloudy after many wash cycles Glass and utensil damage Causes Glass type an
19. gram To ensure that the spray jet can reach all parts arrange the baking sheets as illustrated max 4 baking sheets and 2 grilles Never operate the dishwasher without the top basket or baking sheet spray head some models AquaStop guarantee does not apply to appliances without AquaStop In addition to warranty claims against the seller based on the purchase contract and in addition to our appliance warranty we will pay damages under the following conditions 1 If our AquaStop system is defective and causes water damage we will make good the damage for private users To ensure water damage protection the appliance must be connected to the power supply 2 This liability guarantee is valid for the service life of the appliance 3 A prerequisite for the warranty claim is that the appliance has been correctly installed and connected with AquaStop according to our instructions This also includes the correct installation of the AquaStop extension original accessory Our warranty does not extend to defective feed lines or fittings up to the AquaStop connection on the tap 4 If your appliance is fitted with AquaStop you can leave your appliance unattended during operation and leave the tap turned on afterwards The tap should only be turned off if you are absent from home for a prolonged period e g several weeks holiday Z Repair order and advice on faults GB 0844 892 8979 Calls from a BT landline will be charged at up t
20. heat storage capacity and therefore dries less well Cutlery not dry Cutlery not arranged properly in the cutlery basket Cutlery not arranged properly in the cutlery drawer Separate cutlery if possible prevent contact points Arrange cutlery properly and separate if possible Appliance interior wet after No appliance fault rinse cycle On account of the Condensation drying principle water droplets are physically induced and required in the container The humidity in the air condenses on the inner walls of the dishwasher drains and is pumped out 26 Fault Food remnants on the utensils Detergent residue Water stains on plastic parts Cause Utensils placed together utensi overfilled Spray arm rotat 00 closely s basket ion obstructed Spray arm nozz Utensils preclea es blocked Filters L26 dirty Filters L26 inserted incorrectly and or not engaged Rinse programme too weak ned too intensely sensors therefore decide on weak programme sequence not set to same Detergent dispenser cover blocked by uten Stubborn soiling cannot be completely removed Tall narrow receptacles in corner areas are not rinsed adequately Top basket 22 on right and left height sils and therefore does not open fully Detergent dispenser cover blocked by the tablet Tablets used in th programme Dissolving time
21. hen cleaning the waste water pump ensure that you do not injure yourself on pieces of broken glass or pointed implements Fault what to do aus In this case 1 First always disconnect the appliance from the power supply 2 Take out top basket and bottom basket 27 3 Remove the filters 26 4 Scoop out water use a sponge if required 5 Prise out the white pump cover as illustrated using a spoon Grip the cover on the crosspiece and lift diagonally inwards Remove cover completely 6 Check impeller wheel and remove any foreign objects 7 Place cover in the original position and press down until it engages click 8 Install filters 9 Re insert baskets 23 aus Fault what to do Fault table Fault Check water supply display 3 _ lights up Error code Eid is lit SL Error code 2 4 is lit Error code 75 is lit Error code E 2 7 is lit 24 Cause Supply hose kinked Tap turned off Tap jammed or calcified Remedial action nstall supply hose without kinks Turn on the tap Turn on the tap ow rate must be min 10 l min hen water supply is open Filter in the water supply blocked Switch off the appliance and pull out Filters are soiled or blocked Waste water hose is blocked or kinked Siphon connection still sealed Cover on the waste water pump loose Waste water pump blocked or cover on the waste w
22. iance with the aid of the height adjustable feet Ensure that the appliance is situated securely on the floor A built under or integrated appliance which is installed subsequently as a free standing appliance must be secured to prevent it from overturning e g by screwing it to the wall or by installing it under a continuous worktop which is screwed to adjacent cupboards The appliance can easily be installed in a fitted kitchen between wooden and plastic walls Waste water connection 1 The required work sequence can be found in the installation instructions If required fit a siphon with an drainage connection 2 Connect the waste water hose to the drainage connection of the siphon with the enclosed parts Ensure that the drainage hose is not kinked crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out Drinking water connection 1 Fasten the drinking water connection to the tap according to the installation instructions using the enclosed parts Ensure that the drinking water connection is not kinked crushed or twisted 2 When replacing the appliance always use a new water supply hose Water pressure at least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inlet rate minimum 10 litres minute Water temperature for cold water connection only Installation and connectio
23. iate rinse Final rinse 45 Dry 5 Q sensitive utensils cutlery temperature sensitive plastic and glasses slightly adhesive fresh food Yo 2L Glass 40 Programme data Possible additional 1 Duration hs options mins 2 Energy consumption in kWh 3 Water consumption in litres 4 With Aquasensor 1 2 15 2 1 50 all 3 15 4 12 2 0 95 1 60 all as 4 8 19 1 2 20 2 0 67 all 3 12 8 4 z IntensivZone 1 10 Express Wash 2 0 80 Speed Perfect 3 13 VarioSpeed 4 10 Half load Extra drying U e rinse ean 40 ntermediate rinse inal rinse 60 Drying 5 Q remnants Utensils and Us cutlery Io 2 Lightly soiled Quick 45 UN m ee ANAS TD Lightly soiled Prerinse Programme selection 0 29 0 80 10 0 15 0 05 You can select a suitable programme according to the type of utensils and degree of soiling Information for test institutes Test institutes can request the conditions for running comparison tests by sending an e mail to dishwasher test appliances com Quote the appliance number E Nr and the production date FD which you can find on the rating plate on the appliance door Overview of programmes aus Extra drying none Clean 45 Intermediate rinse Final rinse 55 Prerinse 17 aus Additional options G Additional options depending on model A
24. l display indicates U i 2 The programme sequence lasts approx 1 min On the digital display is indicated 2 22 3 Switch off ON OFF switch 1 Changing the programme When the START button has been pressed the programme cannot be changed The only way a programme can be changed is by Cancel programme Reset Intensive drying The final rinse uses a higher temperature which improves the drying result The running time may increase slightly Caution if utensils are delicate 1 Close the door 2 Switch on ON OFF switch 1 3 Hold down programme button and press START button until the digital display did is indicated 4 Release both buttons To change the setting 1 Press the button LC to switch the Intensive drying on 2 0 i or off diii 2 Press START button L8 The set value is saved Cleaning and maintenance aus Cleaning and maintenance A regular inspection and maintenance of your machine will help to prevent faults This saves time and prevents problems Overall condition of the machine m Check spray arm for grease and limescale deposits If you find such deposits Fill detergent dispenser with detergent Start the appliance without utensils in the programme with the highest rinsing temperature Clean the appliance with detergents appliance cleaners which are particularly suitable for use with dishwashers To ensure that the door seal always remains clean and
25. lf load isteneni ee ne 18 HygienePlus nsa pni ennea EEEa 18 Intensive zone kee ee 18 Extra drying eas cee een 18 Operating the appliance 18 Agq aisensOr aeei Samt Dei 6 18 Switching on the appliance 19 Programme sequence indicator 19 Remaining running time display 19 Timer programming 19 End of programme 19 Automatic switch off interior light 20 Switching off the appliance 20 Interrupting the programme 20 Terminating the programme 21 Changing the programme 21 Intensive drying 21 Cleaning and maintenance 21 Overall condition of the machine 21 Rinserald 4 vani nekaa tan 22 Fillers sans aaa NA 22 Spray AlMS ate ashe ah ana ae 22 Fault what todo 23 Waste water pump 85 23 Faultdable 4 208er 24 aus Intended use Customer service 31 Installation and connection 31 Product package 31 Safety instructions 32 DELIVERY ar sa nannten 32 Technical specifications 32 Installation 32 Waste water connection 32 Drinking water connection 33 Electrical connection 33 Removing the appliance 34 Transportation 34 Protection against frost Emptying the appliance 22 2222 34 Intended use This appliance is intended for use in the home and
26. n aus Electrical connection Connect the appliance to an alternating current only ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor See rating plate for required fusing 31 The socket must be near the appliance and freely accessible following installation If the plug is not freely accessible an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions m The connection may be modified by technicians only A power cord extension may be purchased from customer service only m Use only a residual current operated circuit oreaker which features the symbol Gx Only this extension guarantees compliance with the currently valid regulations The appliance features a water damage protection system Please note the system will not function unless the power supply is connected 33 aus Installation and connection Removing the appliance Protection against frost Also observe If the appliance is in a room where there the sequence of worksteps here is a risk of frost e g holiday home 1 Disconnect the appliance from empty the appliance completely see the power supply Transportation 2 Turn off the water supply 3 Undo the waste water and drinking water connection 4 Loosen fastening screws for the furniture parts 5 If fitted remove the base panel
27. n model The Aqua sensor is an optical measuring device light barrier which measures the turbidity of the rinsing water The Aqua sensor is used according to the programme If the Aqua sensor is active clean rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3 6 litres If the turbidity is greater the water is drained and is replaced with fresh water In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling Switching on the appliance 1 Turn on the tap fully 2 Switch on ON OFF switch 1 The display of the last selected programme flashes This programme remains selected if no other programme button is pressed The expected programme duration flashes on the digital display TO 3 Press the START button L8 The programme starts running Programme sequence indicator _9 my m Your dishes are being a cleaned IN gt Your dishes are being rinsed AR Ss Your dishes are being dried Remaining running time display When the programme is selected the remaining running time of the programme is indicated on the digital display 10 The running time is determined during the programme by the water temperature the number of utensils as well as the degree of soiling and may vary depending on the selected programme Operating the appliance aus Timer programming depending on model Yo
28. not be completely removed 28 See Glass and utensil damage Change detergent brand Clean appliance mechanically Increase detergent dosage or change detergent Select a more intensive rinse programme Select programme with higher washing temperature Use suitable detergent at correct dosage Do not prerinse utensils Remove only large food remnants Can be partly removed with machine cleaner or by mechanical cleaning Coatings are harmless Can be partly removed with machine cleaner or by mechanical cleaning Select programme with higher washing temperature Do not prerinse utensils Remove only large food remnants Fault Removable streaks on glasses glasses with metallic appearance and cutlery Initial or existing irreversible clouding of glass Rust spots on the cutlery The appliance does not start Programme starts automatically The door is difficult to open Door cannot be closed Cause Too much rinse aid low a inse programme section Detergent dispenser cover 35 o ot open fully c QZ completely removed Cutlery not adequately rust resistant Knife blades are frequently more severely affected Cutlery will also rust if rusting parts are rinsed at the same time pan handles damaged utensil baskets etc The mains fuse has tripped Power cord not inserted The appliance door has not been shut properly You did
29. not wait until programme ended Child proof lock is activated Door lock has been activated Door cannot be closed due to installation No rinse aid added or setting too Detergent residue in the final ocked by utensils cover does ensils precleaned too intensely sensors therefore decide on eak programme sequence ubborn soiling cannot be Glasses not dishwasher proof only suitable for dishwasher Fault what to do aus Remedial action Set rinse aid amount to lower setting Add rinse aid and check dosage recommended setting 4 5 Detergent dispenser cover must not be obstructed by utensils Do not place utensils or fragrance dispenser in the tablet collecting tray Do not prerinse utensils Remove only large food remnants Use dishwasher proof glasses Avoid long steam phase standing time after wash cycle ends Use wash cycle at lower temperature se detergent with glass protection omponent se corrosion resistant cutlery om op SE ox Do not wash rusting parts Check mains fuse Ensure that the power cord is plugged all the way into the back of the appliance and into the socket Check that the socket functions Close the door Perform reset See Terminating the programme Deactivate childproof lock See instructions for use at the back Close door with increased force Check appliance installation Door or attached parts must close without
30. nquire at your local authority about current means of disposal Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations e g gt PS lt polystyrene Therefore plastic waste can be sorted out when the appliance is being disposed of Please follow the safety instructions under Delivery Old appliances Please follow the safety instructions under Disposal of your appliance This appliance is labelled in R accordance with European mm Directive 2012 19 EU concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Protection of the environment aus Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front Individual positions are referred to in the text Control panel ON OFF switch Programme buttons Display Check water supply Rinse aid refill indicator Door opener Timer programming Additional options START button Programme sequence indicator 10 Digital display depending on model Number depending on model SEERA BE Appliance interior 20 Interior light 21 Cutlery drawer 22 Top basket 23 Top spray arm 24 Tablet collecting tray 2
31. nstructions Install the appliance in the correct sequence 1 Checking appliance on delivery 2 Installing the appliance 3 Waste water connection 4 Drinking water connection 5 Electrical connection Product package If you have any complaints contact the dealer where you purchased the appliance or our customer service m Dishwasher Instructions for use Installation instructions Warranty Installation materials Steam guard plate Rubber apron Power cord depending on model HO EB EB EO E EEN 31 aus Installation and connection Safety instructions Please follow the safety instructions under Installation Delivery Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order This may cause small water stains These will disappear after the first wash cycle Technical specifications Weight max 60 kg Voltage 220 240 V 50 Hz or 60 Hz Connected load 2 0 2 4 kW Fuse 10 16 A UK 13A Power input switched off 0 1 W not switched off 0 1 W Water pressure at least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inlet rate minimum 10 litres minute Water temperature for cold water connection only Capacity 12 15 place settings depending on model 32 Installation The required installation dimensions can be found in the installation instructions Level the appl
32. nsure that the arrow marks are opposite each other after closing the filter system Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms and 25 1 Check outlet nozzles on the spray arms for blockages 2 Unscrew the upper spray arm 23 3 Remove the lower spray arm upwards 4 Clean spray arms under running water 5 Re engage or screw on spray arms Fault what to do Experience has shown that you can rectify most faults which occur in daily operation yourself This ensures that the machine is quickly available to you again In the following overview you can find possible causes of malfunctions and helpful information for rectifying them Note If the appliance stops during dishwashing or does not start for no obvious reason first run the Abort programme function Reset See chapter entitled Operating the appliance A Warning Don t forget Repairs may be carried out by technicians only If a component has to be replaced ensure that only original spare parts are used Improper repairs or use of non original spare parts may cause considerable damage and put the user at considerable risk Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump The rinsing water will then be above the filter A Warning Risk of cuts W
33. o 3 pence per minute A call set up fee of up to 6 pence may apply IE 01450 2655 0 03 per minute at peak Off peak 0 0088 per minute US 800 944 2904 toll free Contact information for all countries can be found on the enclosed customer service list Robert Bosch Hausger te GmbH Carl Wery Stra e 34 81739 M nchen Germany www bosch home com 9000946099 aus 9312 640MG
34. osed press the lock to open the detergent dispenser Pour detergent into the dry detergent dispenser only insert tablet flat not on its edge Dosage see manufacturer s instructions on the packaging The graduated detergent dispenser helps you add the correct amount of powder or liquid detergent Usually 20 ml 25 ml are adequate for normal soiling If using tablets one tablet is adequate 2 Close the cover on the detergent dispenser by sliding it up until the lock engages without difficulty The detergent dispenser opens automatically at the optimum time depending on the programme The powder or liquid detergent is distributed in the appliance and is dissolved the tablet falls into the tablet collecting tray where it dissolves in doses Detergent aus Tip If the utensils are only lightly soiled slightly less than the indicated amount of detergent is usually adequate Suitable detergents and care products can be purchased online via our website or via customer service see back page A Warning Do not place small parts for washing in the tablet collecting tray 24 this prevents the tablet from dissolving evenly A Warning If you want to add more utensils after the programme has started do not use the tablet collecting tray as a handle for the upper basket The tablet could already be there and you will touch the partially dissolved tablet Notes f programmes are short
35. p Heavily soiled utensils pans should be placed in the bottom basket The more powerful spray jet provides a better dishwashing result Tip Other examples such as the best way of loading your dishwasher can be found on our homepage as a free download The corresponding Internet address can be found on the back page of these instructions for use Cutlery drawer Arrange the cutlery in the cutlery drawer as illustrated Separately arranged utensils are easier to remove after washing The drawer can be taken out Utensils aus Folding spikes depending on model The spikes can be folded down to improve arrangement of pans bowls and glasses Small accessories holder depending on model Light weight plastic accessories e g cups lids etc can be held securely in the small accessories holder 13 aus Detergent Adjusting the height of the basket The height of the upper utensils basket can be adjusted in 3 stages to create more space either in the upper or lower basket Appliance height 81 5 cm Top basket Bottom basket Appliance height 86 5 cm Top basket Bottom basket Pull out the top basket out To lower the basket press in the left and then the right lever on the outside of the basket In doing so hold the sides of the basket along the upper edge to prevent it from suddenly dropping N m
36. ramme is restarted the button lock must be reactivated Damage The appliance may be repaired and opened up by a technician only To do this disconnect the appliance from the power supply Pull out the mains plug or switch off the fuse Turn off the tap a lf the appliance is damaged especially the fascia cracks holes broken buttons or the door function is impaired stop operating the appliance Pull out mains plug or switch off fuse Turn off tap call customer service Disposal 1 Make redundant appliances unusable to prevent subsequent accidents 2 Dispose of the appliance in a n environmentally friendly manner Safety instructions aus A Warning Risk of injury To prevent injuries e g caused by stumbling open the dishwasher only briefly in order to load and unload the dishwasher Knives and other utensils with sharp points must be placed horizontally in the cutlery drawer Do not lean or sit on the open door Inthe case of free standing appliances ensure that the baskets are not overloaded a If the appliance is not in a cavity and a side panel is accessible the door hinge area must be covered at the side for reasons of safety risk of injury The covers are available as optional accessories from customer service or specialist outlets A Warning Risk of explosion Do not add any solvents to the washing chamber Danger of explosion A Warning Risk of scalding Open
37. re that no objects utensil fragrance dispenser are protruding over the basket and preventing the door from closing Refill rinse aid Activation deactivation see chapter Rinse aid Check refill indicator level Clean filters and area underneath see Waste water pump Wait until programme ends or reset See Terminating the programme 25 aus Fault what to do Remedial action Fault Cause Utensils not dry No or too little rinse aid inthe dispenser Programme selected without drying Water collecting in depressions on the utensils and cutlery The combined detergent used has a poor drying performance Intensive drying to increase drying not activated Utensils were removed too early or drying process had not ended yet The eco rinse aid used has a poor drying performance Refill rinse aid Select programme with drying see Overview of programmes Programme sequence Arrange utensils in a sloping position arrange affected utensils as sloping as possible Use different combination detergent with better drying performance Use of rinse aid also increases the drying performance Activate intensive drying see Operating he appliance Wait until program ends or wait until 30 min after program ends before removing utensils Use a proprietary rinse aid Eco products are much less effective Plastic utensils not dry Special properties of plastic Plastic has a lower
38. u can delay the start of the programme in 1 hour steps up to 24 hours 1 Close the door 2 Switch on ON OFF switch 1 3 Press button L6 until the digital display jumps to A I Press 6 or button until the displayed time corresponds with your requirements 5 Press START button 8 timer programming is activated 6 To delete timer programming press the L6 or button until 10 4 77 is indicated on the digital display You can change your programme selection at any time until the programme starts A End of programme The programme has ended when the value ZU is indicated on the numerical display 10 19 aus Operating the appliance Automatic switch off after end of programme or interior light depending on model To save energy the dishwasher can be automatically switched off 1 min or 120 min after the programme ends The setting can be selected from f to F De Fill Appliance does not switch off automatically The interior light comes on when the door is opened irrespective of whether the ON OFF switch is switched on or off When the door is closed the light is off If the door is open for longer than 60 min the light switches off automatically The interior light 20 is lit only when the set value 7 77 is selected i Appliance switches off after 1 min Pile Appliance switches off after 120 min Pi 1 Close the door Switch on ON OFF switch 1 3 Hol
39. y has been correctly installed Safety instructions aus The electrical connection conditions must correspond with the specifications on the dishwasher rating plate 31 If the power cord of this appliance is damaged it must be replaced with a particular power cord To prevent injury the power cord may be purchased from customer service only lf the dishwasher is installed in a high sided unit the unit must be secured properly If the dishwasher is installed below or above other domestic appliances follow the information for installation in combination with a dishwasher in the installation instructions for the particular appliances Also follow the installation instructions for the dishwasher to ensure that all appliances are operated safely If there is no information or if the installation instructions do not include the appropriate information contact the manufacturer of these appliances to ensure that the dishwasher can be installed above or below these appliances aus Safety instructions If you cannot obtain any information from the manufacturer you must not install the dishwasher above or below these appliances If you install a microwave oven above the dishwasher the microwave oven may be damaged Install built under or integratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure stability Do not install the applianc
Download Pdf Manuals
Related Search