Centurion RT Online UPS 1000/2000/3000
Contents
1. and PSCERT3000 Voltage Range OPERATING ENVIRONMENT lt 50dBA 1 Meter Noise Level www powershield com au Power Shield Pty Ltd Warranty Terms amp Conditions PSW28012012 SERVICE WARRANTY Australia Tel 1300 305 393 Warranty Conditions 1 10 11 12 13 14 15 Power Shield product are warranted for certain specified period see item 15 below against failure due to faulty materials or workmanship from the invoice date from the Power Shield Store Power Shields products are covered by a warranty in addition to all rights available to you by statute If within the warranty period the product does not meet the specification above and the product was installed and operated in accordance with Power Shield and Australian standards and procedures then Power Shield will correct any defects due to material or workmanship If the product has been modified recalibrated repaired opened or tampered with in any way by the customer then its warranty will be void If the product has been damaged during transport then warranty will be void If product failed due to fire earthquake flood direct lighting strike terrorism pollution exposed under poison gas and incorrect utility voltage then warranty will be void Batteries must be operated within the technical specification limits of the manufacturer and must be fully re charged at least every three months during storage If Power2. UPS status Backup UPS status time info LOAD K amp Load info Backup time info www powershield com au Display Function ________________ Backup remaining time information Indicates the remaining backup time in pie chart Indicates the remaining backup time in numbers or digits D E H hours M minute Warning amp Fault information Indicates that a warning and fault occurs Indicates the warning and fault codes as listed in detail in section 3 7 and 3 8 fun tay Setting Operation D Input Output amp Battery information Indicates the input output voltage input output frequency Indicates the setting operation and battery voltage Z frequen V voltage H quency Load information HN Indicates the load level by 0 25 26 50 51 75 and ES HEVE AN EOS 76 100 Indicates overload Indicates the load or the UPS output is short circuited Indicates that programmable management outlets are working Indicates the UPS is working in line mode Indicates the UPS is working in converter mode Indicates the UPS is working in bypass mode Indicates the UPS powers the output directly from the mains T ey Indicates the UPS alarm is disabled I Indicates the battery charger is working Battery information a Indicates the Battery level by 0 25 26 50 51 75 and 75 100 g BATTERY 76 100 Indicates low battery B Indicates there is something wrong
3. current rating in order to avoid fire hazards Do not dismantle the UPS system www powershield com au 2 Installation and setup NOTE Inspect the unit before installation for any evidence of mistreatment or damage of contents inside the packaging during transport Store the original package in a safe place for future use NOTE There are two different types of online UPS standard and long run models Please refer to the following model table Model No Model No PSCERT1000 PSCERT1000L PSCERT2000 Standard PSCERT2000L Long run PSCERT3000 PSCERT3000L 2 1 Rear panel view AC Input 10Amp IEC AC Input 10Amp IEC PSCERT1000 L PSCERT2000 7 AC Input 15 Amp IEC AC Input 15 Amp IEC PSCERT3000 L PSCERT2000L SSS Inne l yen see ROX Dm EEK ie z CA SA A gt Ly W SSE poe D a a A i an Programmable outlets connect to non critical loads Output receptacles connect to mission critical loads AC input Input circuit breaker Emergency power off function connector EPO USB communication port RS 232 communication port SNMP intelligent slot External battery connector d EAR QE ee al u www powershield com au 2 2 Installing the UPS For safety the UPS is shipped from the factory with the battery wires disconnected Follow the steps below to re connect the battery wire
4. Shield at its sole discretion determines that the product has failed under Power Shield warranty conditions then Power Shield will at its option repair or replace the faulty unit Power Shield will at its sole discretion replace the faulty product with an equal or equivalent model of a similar age and condition If the product has failed due to reasons that Power Shield at its sole discretion determines to be outside of warranty conditions or is found to be not faulty then a minimum inspection and handling fee will be charged and also freight will be for the customer s account Blown fuses are usually as a result of overload and are not considered a warranty condition and a handling and inspection charge will apply as above For hardwired products larger than 3KVA the warranty covers onsite repair for metro areas in capital cities only For equipment installed in remote locations Power Shield may at its sole discretion request that the product be returned to a Power Shield service centre at the customer s cost Power Shield UPS products are not failsafe devices Although well designed and manufactured like all electrical electronic and mechanical devices it has the potential to fail This should be taken into consideration when designing any critical system Subject to the applicable Law in no event shall Power Shield Pty Ltd it s officers directors affiliates or employees be liable for any form of indirect special consequential
5. connected The LCD display is shown at right Step 2 Press and hold the Select button for 5 seconds to enter Setting mode Step 3 Press the Up button ON MUTE to switch to 07 of program list Then press Enter button to enter value setting of parameter 2 Press the Up button to change the value to ENA to enable the programmable outlet function Then press Enter button again to confirm the setting Step 4 Press the Up button ON MUTE again to switch to 08 of program list Then press Enter button for setting programmable outlet time Push Up button to change the value of backup time according to your demand Then press Enter to confirm the setting Step 5 Press Up button ON MUTE to switch to 00 of program list Then press Enter button to exit setting menu Step 6 Disconnect AC input and wait until the LCD display is off The new setting will be activated when the UPS is turned on again 20 www powershield com au 3 6 Operating Mode Description mode Rack Display Tower Display Online mode EGO mode Efficiency Corrective Optimizer AECO mode Advanced Efficiency Corrective Optimizer Frequency Converter mode Rack Battery mode Bypass mode Standby mode LO AD ae ae waw When the input voltage is within acceptable range UPS will provide pure and stable AC power to output The UPS will
6. of this product Please keep this manual in a safe place for future references www powershield com au Special Symbols The following symbols are used on the UPS to alert you to important information CAUTION Risk of Electric Shock Do Not Open Cover CAUTION To reduce the risk of electric shock Do not remove cover or back No user serviceable parts inside Refer servcing to the factory RISK OF ELECTRIC SHOCK Indicates that a risk of electric shock is present and the associated warning should be observed CAUTION REFER TO OPERATOR S MANUAL Refer to your operator s manual for additional information such as important operating and maintenance procedures SAFETY EARTHING TERMINAL Indicates the primary safety ground This symbol indicates that you should not discard the UPS or the UPS batteries in the trash The UPS may contain sealed lead acid batteries Batteries must be recycled www powershield com au Table of Contents 1 UillDOr tan Sale O Ya TI y u Henry AO Na e seen kla k ae eka Rya A DAN N an KRA Wl GA a AWA 4 ie ANSDOLLAUON a sy nn wanaya rd en y e d bak NAN ia na biy na Si h ri Sa kann xaka da b ka 4 krna ea ee gt gt eeee e e pp ep eDpeA TrRer rererea aeaoaXP o o rp r Rr e srprprereb b b cc rn 4 Fo Sc DN OM ree r lrr_r_lle gt o gt gt naahrlo_cl ararAi gg cnnenemeronnient 4 t4 Operat E YD oe w e r r r Wera 5 1 5 Mainte
7. or punitive damages arising out of the use service or installation of the products whether such damages arise in contract or tort irrespective of fault negligence or strict liability or whether Power Shield Pty Ltd has been advised in advance of the possibility of such damages Specifically Power Shield Pty Ltd is not liable for any costs such as lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data costs of substitution claims by third parties or otherwise Our products come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the products repaired or replaced if the products fail to be of acceptable quality and the failure does not amount to a major failure Warranty period commences from the date Power Shield invoices the goods ZapGuard Range 1 year CompuGuard SafeGuard Defender Commander Centurion 2 years Platinum Range 1 year Gamatronic Range 1 year To claim a warranty our contact details are as follows Call Service on 1300 305 393 Or Visit www powershield com au rmaform to process an RMA Or Power Shield Pty Ltd Head Office U3 205 Camboon Rd Malaga WA 6090 Any claim for expenses must be provided to us in writing and should be sent to our office detailed above 37 www powersh
8. start fail x Low Inverter voltage Bus over yx Inverter output short Ch era Bus under x Battery voltage too high Bus unbalance a Battery voltage too low ae a Bus short x Over temperature Oa g x __ Inverter soft start fail o x Oved _ _43_ _ arene _ High Inverter voltage i 3 8 Warning indicator Low Battery m z Z N Rapid one beep every second O Overicad mmg 2 short beeps every 2 second Battery is not connected 2 short beeps every 2 second Overcharge Continuously sounding Site wiring fault GEA 2 short beeps every 2 second EPO enable prp 2 short beeps every 2 second Over temperature Leme aR eo oa Continuously sounding Charger failure failure Continuously Continuously sounding mn TH Fault Continuously sounding Bypass Out Bypass Out Range amp ZIN 2 short beeps every 2 second Bypass Frequency Unstable TA 2 short beeps every 2 second EEPROM error EEN 2 short beeps every 2 second 22 www powershield com au 4 Troubleshooting Use the table below to diagnose the UPS system for symptoms and problems Symptom though the mains supply is connected well firmly connected to the normal mains The AC input is connected Plug AC input power cord to the UPS output to AC input correctly EPO function is activated Set the circuit in closed The icon PiNonc the warning position to disable EPO code EF flashing on LCD display function and alarm is sounding 2 short beeps
9. Fower amp amp Centurion RT Online UPS 1000 2000 3000 Uninterruptible Power Supply System IMPORTANT Download latest software www powershield com au downloads NetGuard www powershield com au Introduction Thank you for choosing PowerShield PowerShield Centurion RT UPS series are designed to provide the highest level of protection against disturbances found on electrical power supply lines It is suitable for most applications including IT security telephone broadcasting medical etc The Centurion RT UPS series are designed to provide the most comprehensive protection for your valuable electronic equipment hardware software and data from harmful disturbances found on AC power lines including blackouts power sags power surges under voltage over voltage line noise frequency variation switching transients and harmonic distortions The Centurion RTs true online double conversion topology will continuously protect your equipment by internally isolating your equipment from the utility power ensuring that all your equipment always receives clean uninterrupted and stable power Very Important WARRANTY REGISTRATION In order to validate product warranty it is essential that you register your UPS on line Please Visit PowerShield on line product warranty web page at www powershield com au register products This user manual contains instructions relating to safety installation operation maintenance and warranty
10. also charge the battery in online mode When the input voltage is within setting range 8 Vo UPS will bypass voltage to output for energy saving PFC and INVERTER are still active in this mode setting range 8 Vo UPS will bypass voltage to output for energy saving PFC and INVERTER are off in this mode When input frequency is within 40 Hz to 70 Hz the UPS can be set ata constant output frequency of 50 Hz or 60 Hz The UPS will still charge the battery in this mode z2 a meS o b e al LOAD LOAD v 75 LOW BATT 75 v b KA i ra LOAD s a je LOAD en tne input voltage s within LOW BATT gt 5 a or e A Ya gt D h LOAD v N BAT When the input voltage is beyond the acceptable range or power failure and alarm is sounding 2 beeps every 30 seconds UPS will backup power from the battery When input voltage is within acceptable range but UPS is in overload UPS will enter bypass mode or bypass mode can be set by front panel Alarm is sounding every 10 seconds UPS is powered off without providing output power but the battery is still being charged 21 www powershield com au Fault mode The UPS is in fault mode when no OUtput power is supplied from the UPS and the fault icon flashes on the LCD display The UPS status information continues to be displayed on the screen 3 7 Faults Reference Code Fault event Fault Fault event oe code Bus
11. and the other to the USB or RS232 communication port of your PC With the monitoring software installed you can 8 www powershield com au schedule UPS shutdown start up and monitor UPS status through the PC The UPS is equipped with an intelligent slot to accommodate either an SNMP or AS400 card When installed either the SNMP or AS400 card will provide advanced communication and monitoring options for the UPS Please Note The USB port and RS 232 port can NOT operate at the same time Step 4 Disable and enable EPO function For normal UPS operation connect pin 1 and pin 2 closed switch To activate Emergency Power Off EPO function cut the wire between pin 1 and pin 2 open switch Illustration is in the closed switch position for normal UPS operation Step 5 External Battery Bank connection Connect the UPS to the first Battery Bank and daisy chain any additional Battery Banks in parallel using the external battery cables provided UPS Battery Bank Battery Bank BATTERY BANKS PSRTBB6 suits PSCERT1000 L PSRTBB12 suits PSCERT2000 L and PSCERT3000 L www powershield com au Step 6 Turn on the UPS Press the ON Mute button on the front panel for two seconds to power on the UPS Note The battery will fully charge during the first five hours of normal operation Do not expect full battery run capability during this initial charge period Step 7 Software Installation For optimal computer system p
12. covered and upright in a cool dry location During storage recharge the battery in accordance with the following table Storage Temperature Recharge Frequency Charging Duration 25 C 40 C Every 3 months 1 2 hours 40 C 45 C Every 2 months 1 2 hours 25 www powershield com au 6 Specifications CENTURION RT BATTERY BANKS KH DN 160Vac 140Vac 120Vac 110Vac 5 l based on load percentage 100 80 80 70 70 60 60 0 r Se High Line Trasfer jjo a High line Comeback 290M Freqweney Ronse PAO Prose Site phase witha 2 j Power Factor Correction gt 0 99 nominal voltage 100 load emr TT a TT xak yz ee vegot km T TT TT T TT areye Z27 9090 ywvi Xiji Z IT TMIJMJM M J 9 V VQV JZu a TT mr T T 7 TT T T TT Tronsfer Time Ams Typical meme I1 0 nr 66H Charging Current mox Standard Model 1 5Amp Long Run Model 1Amp 2Amp 4Amp 6Amp factory default is 6Amp en rare Onl debe teme derae teneevez meta PP Sorge Protecon eded 22000 Ames kommers WAE O TT TT HEREKE EEE EEE Ed LCD Display Alarm UPS Status Load amp Battery Level Input Output Voltage Batt Time Remaining and Fault Indicators Audible Alarm Battery Mode Bypass Mode Low Battery Batt Mode Fault Overload a ie PHYSICAL Dimension D x W x H 480 x 438 x 88 mm 600 x 438 x 88 mm 600 x 438 x 88 mm 480 x 438 x 88 mm 600 x 438 x 88 mm Suits PSCERT 1000
13. econds to disable or enable the UPS ON Battery warning This does not Mute any other warnings or errors Up key Press this button to display previous selection in UPS setting mode Switch to UPS self test mode Press ON Mute buttons for 5 seconds to enter UPS self testing while in AC mode ECO mode AECO mode or converter mode Turn off the UPS Press and hold this button for at least 2 seconds to turn off the UPS UPS will switch off to standby mode under normal power or transfer to bypass mode if the Bypass setting has been enabled Confirm selection key Press this button to confirm selection in UPS setting mode Switch LCD message Press this button to change the LCD message for input voltage input frequency battery voltage output voltage and output frequency Setting mode Press and hold this button for 5 seconds to enter UPS setting mode when in Standby or Bypass mode Down key Press this button to display next selection in UPS setting mode Switch to bypass mode With the mains power switched ON press ON Mute and Select buttons simultaneously for 5 seconds The UPS will enter Bypass Mode This action will be ineffective when the input voltage is out of the acceptable range Rack Display Tower Display Load info Battery info Input output and Battery SS a l info B a BEYE BEZKE KITA Battery info Warning amp Fault info Warnin Setting operation b Wn a del amp Fault info zu and Battery Settin info g operation
14. ery Kit Assembiy option Call Service on 1300 305 393 or contact www powershield com au for fully assembled replacement battery kits Alternatively follow the procedures below to assemble new battery kits before replacing used UPS batteries kits 3 battery kit Step 1 Remove adhesive tapes Step 2 Connect all battery terminals by following below chart Step 3 Put assembled battery packs on Step 4 Cover the other side of plastic shell as one side of plastic shells and insert one below chart Then battery kit is assembly well more defect battery on the space Defect battery 6 battery kit Step 1 Remove adhesive tapes Step 2 Connect all battery terminals by following the chart below Tapes 12 www powershield com au Step 3 Place assembled battery packs on Step 4 Cover the other side of the plastic shell one side of the plastic shells as shown below so that the battery kit assembly is ready for installation 13 www powershield com au 3 Operations 3 1 Button operation onmure ff secect forrienter jil 7 jll i r lO Button View ON Mute Button OFF Enter Button Select Button Select Button function used in Bypass Mode or Standby Mode ON Mute Select Button 3 2 LCD Panel gt Turn on the UPS Press and hold ON Mute button for at least 2 seconds to turn on the UPS Mute the alarm After the UPS is in battery mode press and hold this button for at least 5 s
15. every 2 seconds Line and neutral Check mains power socket conductors of UPS input and or building wiring and are reversed then reconnect to UPS system The icon and 5F flashing on LCD display and alarm is sounding 2 short beeps every 2 seconds The external or internal Check if all batteries are battery is incorrectly connected well connected The icon and u___ Jirlashing on LCD display and alarm is sounding 2 short beeps every 2 seconds Fault code is shown as 27 and the Battery voltage is too high Contact your dealer G or the charger is faulty icon is lighting on LCD display and alarm is continuously sounding Fault code is shown as 28 and the Battery voltage is too low Contact your dealer e or the charger is faulty icon is lighting on LCD display and alarm is continuously sounding The icons of ZA and UPS is overloading Remove excess loads from are flashing on LCD display and UPS output alarm is sounding 2 short beeps UPS is overloaded Devices Remove excess loads from every 2 seconds connected to the UPS are UPS output fed directly by the electrical network via the Bypass After repetitive overloads Remove excess loads from the UPS is locked in the UPS output first Then shut Bypass mode Connected down the UPS and restart devices are fed directly by it the mains 23 www powershield com au Symptom Fault code is shown as 43 and The The UPS shut down Remove excess l
16. ield com au
17. nance service and faults cccccesececvavaeceeeeeesesueuavavaeeeeueueneavavavanas 5 2 ANStAN ATION ANG S Ll ss ns nsisa xano di birazan y ar bina NAY Sin ar n EA kaka i baka 6 2 1 Rear Danel VIEW zD e a aeem mm Oooopprrrrp py m yp DEM 6 AS la sla T S N r bg v__jggai 7 250 SCHUNG UD NE UPS issn EE 8 2 4 Battery REDIACEIMOENE Ly k y na ART Anal aia a AW elem 11 2 5 Battery Kit Assembly OPtiOnn cscssevsssseuscrsecseuseusecneuvausecusareuseeusareuseeues 12 Si ODS AUOMS U cJ r e ee gt aoear az 14 3 Le DULLON OPEL UO yiss uu ss a b niri ri hwa yd baxa k t arek ban ab Div Xan Sa S An W SED VAN 14 SEWA LCD Panel scoir EE E 14 celeb Ala bil osea E A 16 3 4 LCD display wordings indeX cccecseeeeesseeeeeeeeeeseeeseeseeeeesenseeteuseneeaneenenass 16 3 5 UPS Parameter SUNOS s yi iaia Aa 16 3 6 Operating Mode Description s sesssssssssnunnnnnnnnunnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnn 21 3 7 Faults Reference Code sssesssssssnunusnnnnnnnunnnnnnnnunnnnnnnnannnnnnnnnnnnnnnnnnnnnnnnn 22 BO Wa INACIO erne a a 22 Ae OUDICSNOOUN PN MN N rrr Dr K 23 5 Storage ANd MAINTENANCE sus seins yi n lal an ka nda ka han ala Helan a wa ata ya karn aa k kena y ann 25 D gt Le OPCAO Dt e _gg_ U 25 se fF AGE arar NN DD lllrrr rrr 25 Delo zalji es ela A E DD DD DN DD aa 26 3 www powershield com au 1 Important Safety Warning For safety reasons it is essential t
18. o comply with all warnings and operating instructions listed in this manual Do not operate the UPS unit before carefully reading through all safety information and operating instructions It is recommended that you save and or backup this manual for future reference 1 1 Transportation e Transport the UPS system using only the original packaging to protect against shock and impact Handling Safety A Do not lift heavy loads without assistance J kg 18 32 ke pi 32 55 kg This equipment is intended for installation in a controlled temperature indoor area free from conductive contaminants gt 55 kg 1 2 Preparation The UPS system must be absolutely dry before installation As condensation may occur if the UPS system is moved directly from cold to warm environments allow at least two hours for the UPS system to acclimate to the environment Do not install the UPS system near water or in moist environments Do not install the UPS system where it would be exposed to direct sunlight or near heaters Do not block ventilation holes in the UPS housing 1 3 Installation Do not connect appliances or devices that may overload the UPS system e g laser printers to the UPS output sockets To ensure against physical hazards place cables safely such that persons cannot accidentally trip over or step on them Do not connect domestic appliances such as hair dryers to UPS output sockets The UPS can be operated by any individual
19. oads from icon EWERIICAT Jis lighting on LCD automatically because of UPS output and restart it display and alarm is continuously overload at the UPS sounding output Fault code is shown as 14 and The UPS shut down Check output wiring and if alarm is continuously sounding automatically because connected devices are in short circuit occurs on the short circuit status UPS output Fault code is shown as 01 02 03 A UPS internal fault has Contact your dealer 04 05 11 12 13 and 41 on LCD occurred There are two display and alarm is continuously possible results sounding 1 The load is still supplied but directly from AC power via bypass 2 The load is no longer supplied Battery backup time is shorter Batteries are not fully Charge the batteries for at than nominal value charged least 5 hours and then check capacity If the problem still persists consult your dealer Battery defect Contact your dealer to replace the batteries 24 www powershield com au 5 Storage and Maintenance 5 1 Operation The UPS system contains no user serviceable parts Please contact your dealer if the battery service life 3 5 years at 25 C ambient temperature has been exceeded as the batteries must be replaced amp Q Be sure to deliver the spent battery to a recycling facility or ship it to your dealer in the replacement battery packing material 5 2 Storage Before storing charge the UPS for 5 hours Store the UPS
20. ponents inside the UPS system are still connected to the battery and electrically live and dangerous Before carrying out any kind of service and or maintenance switch off mains power then disconnect the batteries and verify that no hazardous voltages are present at the terminals of the large storage capacitors the BUS capacitors Only persons who are adequately familiar with high capacity batteries and with the understanding of the required precautionary measures outlined below are permitted to replace batteries and supervise operations Unauthorized persons must be kept well away from the batteries Caution risk of electric shock The battery circuit is not isolated from the input voltage Hazardous voltages may occur between the battery terminals and the ground Before touching always verify that no voltage is present e Batteries may cause electric shock and have very high short circuit currents When working with batteries always ensure the following precautionary measures are adhered to remove all jewellery items wristwatches rings and metal objects use only tools with insulated grips and handles When changing batteries always install the same model and type of batteries e Do not attempt to dispose of batteries by burning as they may explode e Do not open or destroy batteries Escaping electrolyte can cause injury to the skin and eyes and may be toxic e Replacement fuses must be of the same type and amperage
21. rotection install the UPS monitoring software to fully configure UPS shutdown Follow the steps below to download and install NetGuard monitoring software 1 Go to the website www powershield com au 2 Click Downloads software icon and choose your required OS to download the NetGuard software in the http www powershield com au downloads downloads page 3 Follow the on screen instructions to install the NetGuard software 4 When the computer re starts the NetGuard monitoring software will appear as an orange plug icon located in the system tray near the clock www powershield com au 2 4 Battery Replacement NOTICE The UPS is equipped with a hot swappable battery design so the internal batteries can be replaced without shutting down the UPS or connected loads Replacement is a safe procedure isolated from electrical hazards CAUTION Consider all warnings cautions and notes before replacing batteries Note The equipment is not protected from power outages during battery disconnection Step 2 Step 3 Disconnect battery wires Pull out the battery box by removing the two screws on the front panel Step 5 Step 6 Remove the top cover of Re connect the battery wires battery box and replace the After replacing the batteries inside batteries slide the battery box back in the original location and screw it tightly Replace the front panel on the unit 11 www powershield com au 2 5 Batt
22. s before installing the UPS Step 2 Step 3 Remove front panel Re connect battery wires and Replace front panel on the connect the AC input unit This UPS can be used as either a stand alone tower or rack mounted in a 19 chassis Choose from the appropriate installation instructions below to position the UPS accordingly Rack mount Installation Install UPS alone Contact www powershield com au on 1300 305 393 for optional PowerShield Rail Kit PSRK www powershield com au Tower Installation Step 1 Step 2 Step 3 lt Install UPS and external battery ARQ ama 2 3 Setting up the UPS Step 1 UPS input connection When connecting the UPS to the mains supply always use a three pin plug three wire grounded receptacle and avoid using extension cords Step 2 UPS output connection There are two kinds of socket type outputs programmable outlets white coloured outlets and general outlets black coloured outlets Connect non critical devices to the programmable outlets and critical devices to the general outlets The backup time to critical devices may be extended during power failure by setting shorter backup time for non critical devices Step 3 Communication connection Communication port USB port RS 232 port Intelligent slot ff TT Oo Jo To allow for unattended UPS shutdown start up and status monitoring connect the communication cable on one end to the USB or RS 232 port of the UPS
23. vanced ECO mode disable Default setting ENA Bypass mode enable DIS Bypass mode disable Default setting ENA Programmable outlets enable See 3 5 1 DIS Programmable outlets disable Default setting 0 999 setting the backup time limits in minutes from 0 999 for programmable outlets which connect to non critical devices in battery mode www powershield com au e 09 LCD display direction setting e 00 Exit setting RAC the LCD display is horizontal TOE the LCD display is vertical Default setting For 208 220 230 240 VAC models choose from the following Acceptable input voltage range 110 300 alternating flashing acceptable input voltage range is from 110V to 300V Default setting 160 260 alternating flashing acceptable input voltage range is 160V to 260V 170 270 alternating flashing acceptable input voltage range is 170V to 270V Aon LCD display backlight is on all the time Aut LCD display backlight will turn off after 60 seconds if no buttons are pressed Default setting 0 999 Setting the backup time limits in minutes from 0 to 999 in battery mode 0 Maximum 10 seconds of backup time 999 Disable autonomy limitation function Default setting www powershield com au 3 5 1 Steps for setting programmable outlet White Coloured Outlets Step 1 Before entering setting mode ensure the UPS is in either Bypass or Stand by mode off charging and make sure the battery is
24. with battery TxE www powershield com au 3 3 Audible Alarm Battery Mode 2 beeps every 30 seconds Bypass Mode 1 beep every 10 seconds Low Battery Rapid one beep every second 2 short beeps every 2 seconds Continuously sounding 3 4 LCD display wordings index ETIB dewe Ud ELE Frequency Unstable in Bypass Mode ee EE SRO ror 3 5 UPS Parameter Settings LOAD 9 LL i Parameter 2 There are two parameters used to set up the UPS Parameter 1 Is used for program alternatives Parameter 2 Is used for setting Parameter 1 information display www powershield com au e 01 Output voltage setting Setting LOAD erface For 208 220 230 240 VAC models you may choose the following output voltage 208 sets output voltage to 208Vac 220 sets output voltage to 220Vac 230 sets output voltage to 230Vac 240 sets output voltage to 240Vac Default setting CF ENA converter mode enable CF DIS converter mode disable Default setting The frequency may be set in battery mode BAT 50 sets output frequency to 50Hz BAT 60 sets output frequency to 60Hz If converter mode is enabled output frequency can be selected CF 50 sets output frequency to 50Hz CF 60 sets output frequency to 60Hz ENA ECO mode enable DIS ECO mode disable Default setting www powershield com au e 05 AECO enable disable ENA Advanced ECO mode enable DIS Ad
25. without previous experience Always connect the UPS system to an earthed shockproof outlet that is easily accessible and close to the UPS system Use only VDE tested CE marked mains cable e g the mains cable of your computer to connect the UPS system to the building wiring outlet shockproof outlet Use only VDE tested CE marked power cables to connect the loads to the UPS system When installing the equipment ensure that the sum of the leakage currents of the UPS and the connected devices do not exceed 3 5mA www powershield com au 1 4 Operation e Do not disconnect the mains cable on the UPS system or the building wiring outlet shockproof socket outlet during operations as this will cancel and invalidate the protective earth of the UPS system and of all connected loads e As the UPS system features its own internal current source high capacity batteries the UPS output sockets may be electrically live even if the UPS system is not connected to the building wiring outlet e In order to fully disconnect the UPS system first press the OFF Enter button to disconnect the mains e Prevent fluids or other foreign objects from entering inside the UPS system 1 5 Maintenance service and faults The UPS system operates with hazardous voltages Repairs should only be carried out by qualified maintenance personnel e Caution risk of electric shock Even after the unit is disconnected from the mains building wiring outlet com
Download Pdf Manuals
Related Search