DOBBY-Jacquard™ Loom User`s Manual
Contents
1. Ifthe warp width is 40 and we are using 2 sections our number of sec tions is 20 All together we can say OF YARDS PER SPOOL LENGTH OF THE WARP x OF SECTIONS TOTAL YARDAGE If it is a single color warp or if a color sequence is repeat ing in each section the same spools or cones can be used to wind all the sections needed for the warp TOTAL YARDAGE OF SPOOLS x OF YARDS PER SPOOL It is important to make these calculations in advance so that you can purchase your yarn in spools or cones corresponding to the amount of yardage needed on each Sometimes this is not possible and you will need to wind your own spools from yarn that is in larger packages For doing this you will need empty plastic spools a bob bin winder preferably electric and a yardage counter These items are available from AVL You might want to make a permanent set of extension cords to use when warping the sectional beam Extension cords are also called apron cords and have the same function as the apron on the plain beam They give you reach from the warp beam and allow you to weave every possible inch until the end of the warp touches the last shaft you are using Make them out of a strong non stretch able linen or cotton cord You will need to make one extension cord for each section in your sectional beam For each extension cord cut a piece of cord Take the two ends of the cord and knot them together Measure to make sure th2. one section at a time to make the warp that is already on the beam tight The idea of this method is that the warp does not need to be under tension all the time but the part that is on the beam has to be tight Make another turn go to the back of the loom and jerk all the sections again and so on If you have a wide warp you might need to do up to ten jerking motions after each turn When you come to the end of your warp insert lease sticks in your threading cross Now remove the ties from each individual threading cross and spread the warp out on the sticks When the warping is completed free the warp from the raddle If you have an AVL raddle first untie the security strings lift the raddle top off and remove the warp from the raddle Afterwards replace the top on the raddle and leave it in its place on the back of the loom if so desired as it will not interfere with the weaving pro cess Then be sure to bring the end of the warp around the separa tion beam so that it now travels into the loom For those who ordered the second plain beam it is wound in exactly the same manner as the first warp beam except if you put a second beam in the bottom position The loom is designed to carry two Plain Warp Beams or a Single Sectional Beam There will be times when you will want to use more than one warp which can not be put together on one beam You will have to put them on separate beams or use some kind of separate tension s
3. plastic bag Make sure that each bundle is not too thick You will know when you need to divide each bundle if you feel that all the threads are not being tensioned evenly The weight needs to have a strong loop of string on it so the warp bundles can be slip knotted into it This makes it easy to undo the slip knot and move the weight when it climbs up to the back beam and must be let down again Page 1 19 WARPING THE SECTIONAL BEAM WARPING THE SECTIONAL BEAM Sectional Beam Page 1 20 Calculation The weight also needs to be adjustable Plastic bottles with handles filled with water are perfect You can also use fish ing weights washers nuts bolts They are not as easily adjustable like water bottles but take less space The lower to the floor you can hang them the less often you need to reposition them The AVL sectional beam is designed to be warped in sections with the use of a tension box The yarn travels directly from cones or spools which are mounted on a rack behind the loom through the tension box and onto the beam Throughout the warping process the tension box automatically keeps a constant and uniform ten sion on the warp Not only does this system save time but it makes it possible to wind on very long warps which would never fit on a warping board or reel First you must calculate the number of spools or cones of yarn you will need Each section is wound onto the sectional beam separate ly
4. therefore you ll need to have one spool or cone for each end in that section if your section is 2 wide with sixteen E P I that would be thirty two spools or cones of yarn NOTE It used to be that all sections were 2 wide On an AVL sectional beam with metal pegs you can decide to use 1 2 or any number of inches sections You can simply add more pegs in the pre made holes or take them out To prepare for sectional beam warping we need to calculate how many spools we need to wind how many yards do we need to wind on each spool total yardage for the project NUMBER OF SPOOLS Sectional beaming requires the use of as many spools loaded with thread per individual section as your planned sett in the reed dictates To calculate the actual number of spools required we need to know how many EPI are we going to use in the fabric what SIZE SELECTION will we have to use in the fab ric If your warp is set at 24 e p i per 1 you will need 24 spools for a sectional beam with 1 sections or 48 spools for a beam with 2 sections Therefore we can Say OF SPOOLS EPI x SIZE OF THE SECTION Extension Cords WARPING THE SECTIONAL BEAM NUMBER OF YARDS PER SPOOL To calculate the number of yards per each spool we need to know the LENGTH OF THE WARP NUMBER OF SECTIONS on the beam We calculate the number of sections by dividing the WIDTH OF THE WARP by the SIZE OF THE SECTION
5. DOBBY Jacquard Loom User s Manual AVL Looms 3851 Morrow Lane Suite 9 Chico CA 95928 8305 800 626 9615 info avlusa com Version 1 0 May 2006 Page 1 1 TABLE OF CONTENTS Page 1 2 TABLE OF CONTENTS FIGURE INDEX GETTING THE LOOM CONNECTIONS HEDDLES PRESSURE AND OTHER AIR ISSUES WEAVING JACQPOINT 1 0 14 UPGRADE SYSTEM DESCRIPTION WEAVE CYCLE DETECTION AND SHED CONTROL FOOTSWITCH SENSOR WIRING COMPU DOBBY SPECIFICS WARPING THE PLAIN BEAM Creating Two Crosses Securing the Crosses Removing the Warp for the Warping Board Adjusting the Tension Device Attaching the Raddle Winding the Apron Attaching the Warp to the Apron Inserting Sticks in the Raddle Cross Feeding the Raddle Preparing the Paper Winding the Warp Threading Cross Removing the Raddle Two Beams When Do You Need to Tension Your Warps Separately Setting Two Beams More Than Two Warps Separate Tensioning WARPING THE SECTIONAL BEAM Sectional Beam Calculation Extension Cords Feeding the Spool Rack Positioning the Tension Box Tension Box Tension Box Heddle Installation Instructions Threading the Tension Box Winding the Warp Adjusting the Size of the Section Counting Turns or Yardage 1 2 1 4 1 5 1 6 1 7 1 9 a a en a 1 PN el el et el ee en a ee ee AMDOAONADUUAARARAWWN a ee l NNNNNNNNNNN DUUWNNNNF OO TABLE OF CONTENTS Creating the Cross 1 26 Inserting Sticks in the Threading Cross 1 27 Readjusting the Te
6. R THE SETT THE HEDDLES SHOULD ALWAYS STAY AT THE SAME HEIGHT TO MAKE A CLEAN SHED Use the rods to keep the heddles at their proper height Please note the heddles must slope from front to back to main tain the proper shed geometry Figure 5 Page 1 7 HEDDLES SOC HREOC OEE EOEEE Figure 6 Keep the angle necessary to have all the threads go through the loom without impeding one another The Comber Strips may be pushed against one another or may be spread through the use of the spacing strips that were supplied with your loom AVL Jacquards have a very wide range of warp setts but you must learn the system to get the sett correctly Note the Heddle Spacer Supports have two rows of holes Use either row of holes with the Heddle Spacer Rods to keep the heddles at the correct height The last part of the heddle adjustment is the Tie Down Bars They must be moved to roughly correspond to the space of each row Tension is applied by sending air to the Heddle Tension Cylinder Ap ply air and the heddles will tighten up Page 1 8 PRESSURE AND OTHER AIR ISSUES PRESSURE AND The AVL Jacquard System operates generally at eighty p s i at the OTHER AIR Flow Control Unit It is important that you regulate the air pressure ISSUES at the Flow Control located at the Control Unit Each hook is controlled by its own valve located in the head The valves are sensitive Figure 7 Figure 8 Applying more pressure to th
7. at they are long enough to reach all the way to the harnesses All extension cords should be exactly the same size When measuring the length of the cords also check to be sure that when the cords are wound on to the beam the end of the loop and any knots in the cords fall between the crosspieces of the sectional beam not on them A sectional beam is usually not solid It is a frame that has metal pegs That way you can keep the warp smooth on the beam without going over the knots of threads Page 1 21 WARPING THE SECTIONAL BEAM Feeding the Spool Rack Positioning the Tension Box Tension Box Tension Box Heddle Page 1 22 Installation Instructions Next place a spool or cone rack about five or six feet behind your loom Place the spools or cones for the first warp sections on the cone rack Make sure you put each thread through the metal eye on the spool rack so the threads do not get tangled When arranging the spools on the spool rack it doesn t matter whether you go top to bottom or bottom to top the important thing is to be consistent in vertical columns and to place the spools in the order that the threads are in the warp Before winding the sectional beam make sure to disengage the tension system so that the beam will turn counterclockwise swiftly To do this unlock the tension rope from the spring and completely unwrap the plastic cord from around the tension beam drum Also remember to remove the w
8. beam proceed to the section titled Warping the Sectional Beam Various warping methods can be adapted to the AVL loom How ever we recommend the following method in which the warp is first wound on to the plain beam with the use of a raddle Please study this method and try it We have found that it aids in getting a uni form warp tension especially when dealing with long warps WARPING THE PLAIN BEAM Creating Two To begin wind the warp on a warping board or reel Make sure you Crosses put in two crosses the threading cross the raddle cross Figure 11 CREATING TWO CROSSES In the threading cross each thread crosses the next thread in op posite directions In the raddle cross groups of threads cross each other The number of threads in a raddle group can be determined by the number of ends to be placed in each section of the raddle or by the number of threads you are holding in your hand while wind ing the warping board Securing the Before removing the warp from the board or the reel secure the Crosses crosses Use four ties to secure each cross These ties go on each side of both pegs holding the cross It is usually a good idea to use different color threads for the ties on the tops of the pegs and another color to tie the bows underneath the pegs By color coding your ties you are less likely to twist the warp later Page 1 13 WARPING THE PLAIN BEAM Removing the Warp for the Warping Boa
9. beam within the section is not going to grow evenly Therefore you will end up having lots of tension problems To determine the length of the warp you are putting on the beam you need to count either turns revolutions or yards Page 1 25 WARPING THE SECTIONAL BEAM Counting Turns or To count turns you can do it in your head but it is more reliable to Yardage use a digital or mechanical revolution counter Counting revolutions even with a digital counter will still give the ap proximate warp length only because the circumference of the beam will increase slightly with each rotation This is called beam build up To count yards with a yardage counter while warping the sectional beam you need to place the yardage counter at the front of the tension box You should use an extra thread for measuring yard age because if you use one of the threads from your warp section that particular thread would have a different tension once you start weaving The extra thread you use for measuring purposes only can be reused for each section FRONT PIVOTING REED Figure 19 ATTACHING THE YARDAGE COUNTER TO THE TENSION BOX Creating the Cross When there is about a half yard left to be wound onto the beam it is Page 1 26 time to make the threading cross Simply push on the rear heddle frame of the tension box making half of the threads go up and the other half go down Now slip in an eight inch piece of contrasting thr
10. e unit will help lift a hook but may make it slow to drop due to a greater amount of exhaust air Con versely reducing the air may help the hook to retract but may result in slow action So it is necessary to find a happy medium Start at forty p s i it is a good beginning Remember different warps may require slightly different pressures So experimentation is key WEAVING The Shed is opened with the Foot Pedal Each time the pedal is tapped the loom will form a new shed The loom is controlled by Jac qgPoint software Once in Loom Control JacqPoint will display the present pick and the next pick JacqPoint will display the finished Point Paper which can be adjusted at any time In order to execute Jacqpoint 1 0 14 the computer to be used must have the capabil ity of two 2 RS 232 Serial Ports Figure 9 Foot Pedal Page 1 9 JACQPOINT 1 0 14 UPGRADE JACQPOINT 1 0 14 UPGRADE SYSTEM DESCRIPTION WEAVE CYCLE DETECTION AND SHED CONTROL Page 1 10 The following areas of Jacqpoint were changed or revised a Added a five minute cylinder de activation timeout to avoid excessive temperature build up on the cylinder pneumatic valves This upgrade will cause all Jacquard hooks to drop if a cycle is not performed within five minutes of the previ ously issued cycle NOTE in case that the timeout does oc cur weaving may need to be placed in Reverse mode if the timed out pick was not compl
11. ead called a mark ing thread through the opening called a shed created between the threads above and the threads below Locate this marking thread about half way between the tension box and the separation roller Inserting Sticks in the Threading Cross Readjusting the Tension Combining Sectional and Plain Warping WARPING THE SECTIONAL BEAM Now push on the front heddle frame making the other half of the threads go up Now take one end of your marking thread and bring it through this shed The two ends of the marking thread should now be together Tie them in a bow knot Wind the rest of the first section on cut the ends and secure to the wound on thread using a rubber band over the pegs Continue winding all the sections in the same manner by moving the tension box along its track When all the winding is complete remove the rubber bands unwind a few feet of warp and slip one lease stick through the path created by the upper portion of each marking tie Now slip another lease stick through the path created by the lower portion of each mark ing tie Secure the lease sticks together leaving about two inches between them using masking tape or string through the end holes of the lease sticks Now bring the lease sticks with the warp ends around the separation beams so that warp travels towards the center of the loom harnesses Remove the breast beam from the position behind the harnesses and place it to its original pos
12. eight from the tension arm if you have automatic tension on your loom On the beam on the back of the loom set the tension box That position will allow the tension box to travel from one section to an other The tension box is fastened to the separation beam with wing nuts These can be released for the tension box to move Once centered properly for a particular section the tension box needs to be tightened again for each section The tension box is an essential warping tool which Puts threads under tension Spreads threads to the proper width Makes thread by thread lease If this is your first time to use a tension box you need to install heddles on the harnesses Your tension box is delivered with one bundle of one hundred hed dles These are held together with twist ties Leave these on for now Refer to the upcoming diagram to familiarize yourself with the tension box and its parts Push down on one of the harnesses until it stops This causes the other harness to go up You will use that later for making a threading cross Right now we ll need to use it to help in the assembly of the heddles to the harnesses Remove the heddle retainer of the harness that is up using a phillips head screwdriver Notice there are four twist ties holding the heddles together Separate the top two Insert the top bar of the harness that is up into the space created by pulling apart the twist ties Insert the botto
13. eted b Added a 0 5 second delay from the footswitch activation to the time that the hooks harnesses are actually raised This change corrects the tendency of the loom to execute con secutive picks if the footswitch is held active for an extended period of time c On Alternating Dobby mode corrected malfunction in that both Jacquard and Dobby skip every other pick advance two picks with each footswitch activation The computer Jacgpoint 1 0 14 software interacts strictly with the JackRabbit Module contained in the Jacquard Controller hardware Depending on the selected options of Jacqpoint i e under the Weave tab and under Dobby Options Use Dobby in Simultane ous or Alternating mode the Compu Dobby may or may not be selected Regardless of the Dobby settings the computer sends and re ceives data to from the Jacquard Jackrabbit Module through RS 232 serial port 1 If the Dobby is selected in software then the computer also only sends data to the Compu Dobby through RS 232 serial port 2 At no time does the computer receive data from the Compu Dobby Whenever the Dobby is selected data is issued through serial port 2 Dobby Port either at the same time as to Jacquard port 1 if in Simultaneous operation mode or at every other detection of the footswitch activation when in Alternating mode A cycle is executed with every two activations one to raise the second
14. he ends will be tied to the apron rod Notice that the apron has two hemmed ends One end has open ings in it and the other end has a velcro strip Take the end with the velcro and secure it to the cloth storage beam making sure it is centered Figure 20 WARP ROUTING Then wind the apron once around so that it holds itself in place Route the apron up and around the cloth beam Spread it out flat and center it over the cloth beam and insert the metal rod into the hem Now tie the ends to the metal rod Starting from the middle bring a first bundle toward you over the apron rod then around and under it Divide it in half and bring one half up on each side of the bundle Use the ends to tie a surgeon s knot It is the same as the first tie you make tying a shoelace except you loop the end through twice This kind of knot is very good for readjusting the tension LL Figure 21 Tying on to an Old Warp THREADING SLEYING AND TYING ON Start with one section in the middle then the far right and the far left outside ones Work your way in By now the sections that were tied first are quite a bit looser than the ones tied last To correct this you do not need to untie the knots simply grasp the ends and pull them away from you then re tighten the knots Repeat this until all of the section are at approxi mately the same tension A new warp can be tied on to an old warp thus eliminating the threading and sleying
15. he one that can be sleyed evenly and as close to the desired section width If you can not get the exact width of the section sley your reed slight ly wider This will make it just slightly wider than the space between the pegs The section will be narrowed down by pivoting the reed Never sley the reed narrower than the section on the beam There is no way to expand it After the tension box is completely thread ed the larger pegs are moved downward to apply tension The fur ther down they are moved the more tension will be applied to the yarn This is an adjustable system as different yarns require more or less tension With a heavy wool the pegs may only need to be moved half way down whereas with a fine silk the pegs may need to be moved all the way down and the yarn wrapped an extra time around one of the stationary pegs to get the proper tension Once you have adjusted the tension correctly do not change it dur ing the winding of the beam as long as you are using the same type of yarn Once the tension box has been threaded it is not always necessary to rethread it If you need to change spools or cones simply tie the new ends on to the old ends just before the rear stationary reed then gently pull on the old ends until the new ends have come all the way through the box WARPING THE SECTIONAL BEAM Winding the Warp Before you start winding the warp attach the extension cord to the Adjusting the Size of the Section P
16. hen wound on the beam Put the raddle top on or secure warp threads with rubber bands Instead of a regular raddle you can put a mini raddle in place of the front reed on the tension box In this case the tension box is used only for guiding threads into the sections You do not thread threads in the tension box through the harnesses nor through the back reed and you do not adjust tension with the pegs Attach each baby warp to the extension cords and proceed as in regular sectional beaming procedure Since you are not using the tension box for tension be sure to keep it taut manually When you come close to the end of the section take the reed cover off and continue winding the rest of the baby warp Secure that section to the beam and continue to the next one To prepare for threading tie the threading cross sticks in a comfort able and visible position for threading You may also find it helpful to raise the harnesses To raise the har nesses pull the dobby arm down to the bottom of its slot To secure the arm in this position simply insert the wooden retainer block On the bottom of the dobby unit are 16 cable ends corresponding to the 16 harnesses or 24 cables for 24 harnesses In turn pull each cable end downward on each cable into its slot in the arm thus raising the harnesses Make sure to lower the harnesses again when threading is completed Never remove the block while any harnesses are lifted as this
17. i beam and the section of the warp to an extension cord tie an over head knot in the warp threads from one section and slip that knot into the opening of the larkshead knot you created in the extension cord Pull it tight Line up the tension box approximately behind the section you will be winding Now wind about one yard onto the beam As you wind you will need to fine tune the placement of the tension box along the track When it is centered properly tighten down the wing nuts un der the tension box At this point you can pivot the pivoting reed section so that the yarn comes close to but doesn t quite touch either the peg to the left or the peg to the right Now tighten the wing nut under the pivoting reed This shouldn t need to be read justed until you are using yarn of a very different size Extra care to correctly center and adjust the width of each warp sec tion will result in more perfect tension while weaving DEC il AK Figure 18 Make sure that the threads are going on to the beam in flat layers If you notice that warp piles up at the pegs the section of the warp is too wide If the warp falls down at the pegs the warp section is too narrow If any of the above is happening go back and pivot the front reed on the tension box again until you get perfectly flat layers This is very important otherwise you will end up having different length threads in one section since the circumference of the
18. ically attached to the Dobby Lift Cylinder The Reed Switches interface with the Jacquard circuitry through the 3 pin Amphenol connector on the Jacquard Controller Box Wiring is as follows Signal Description Sense Down Normally 5 VDC momentarily goes to 0 VDC when Dobby Lift cylinder is retracted Sense Up Normally 5 VDC momentarily goes to 0 VDC when Dobby Lift Cylinder is extended Ground 0 VDC Page 1 11 COMPU DOBBY SPECIFICS COMPU DOBBY SPECIFICS WARPING THE PLAIN BEAM Page Ts42 Standard Compu Dobby firmware contains a Sleep Mode function which causes suspension of operation if the unit is selected for an extended period of time without actual weaving receiving Up or Down signals Figure 10 Compu Dobby Typically once Sleep Mode is entered it requires that the operator cycle the treadle footswitch to Wake Up operation Since in Jacquard Dobby Combination systems the Up Down sensors are not wired to the Compu Dobby there is no way for the Compu Dobby to receive the signals necessary to cause it to Wake up therefore an optional jumper on the CDII I O Board must be in place to prevent the Compu Dobby from entering Sleep Mode This jumper must be installed at location H8 between pins 9 and 10 of the CDII I O Board We suggest you beat with a CLOSED shed but this is the weaver s choice If you have ordered only a sectional
19. ition on the front of the loom Now tie the lease sticks on the side of the loom so that they are at eye level when you are in your threading position To keep the warp from slipping forward during the threading pro cess rewind the tension rope around the pulley and tension drum and clip the rope end to the spring If you are winding a very fine warp say forty ends to the inch or more and do not have or do not want to wind a lot of spools or cones it may be more convenient to wind separate warp sections on a warping board or reel and go from there directly to the sectional beam If you decide to do this however your warp will be limited in length by what will fit on the warping board or reel If you choose this method follow these steps Calculate number of threads for each section on your section al beam On the warping board or on the warping reel make baby warps for each section on your beam if you are using a warping board you will be limited in length Make crosses at each end raddle cross on one side and thread by thread cross on the other Take the warp off the board or reel by taking off the thread by thread cross first Page 1 27 THREADING SLEYING AND TYING ON THREADING SLEYING AND TYING ON Preparation for Page 1 28 Threading Put the warp threads from a first baby warp in the raddle making sure that threads are spread evenly and that they are creating flat layers w
20. m bar of the harness that is up into the space created by pulling apart the bottom two twist ties making certain that the heddles aren t twisted Now remove the twist ties Threading the Tension Box 7 AQA TENSION PEGS WARPING THE SECTIONAL BEAM Count off fifty heddles and cut the loop at the top between the 50th and the 51st heddle Now put the four twist ties back on the fifty heddles that were the last to go on the harness Remove these fifty and reattach the heddle retainer Now push down on the harness that is up making the other harness come up Remove the heddle retainer Pull apart the top two twist ties and insert the top of the har ness which is up into the space created Pull apart the bot tom two twist ties and insert the bottom of the harness into the space created e Reattach the heddle retainer The best way to thread the tension box is to take one thread from the cone rack and thread it all the way through all the parts of the tension box then the next thread all the way through It works best to use the threads from the rack in a vertical order rather than a horizontal order HARNESSES WITH HEDDLES STATIONARY REE PIVOTING REED ADJUSTABLE TENSION PEGS Pa SS KITT NS N y e o l KS YARDAGE COUNTER NZ REMOVABLE HEDDLE RETAINERS EYE OF HEDOLE YARN STATIONARY POSITION OF PEGS WITH MEDIUM TENSION APPLIED Fig
21. ns are going to need extra help in order not to slip off themselves To do this cut your paper four inches wider than the warp width and then fold over the edges an inch on each side Be sure the warp is wound between the two folded edges not overlapping them WARP WIDTH 4 WARP WIDTH WARP WIDTH 3 BROWN WRAPPING PAPER P i l i Figure 14 PREPARED PAPER WITH FOLDED EDGE WARPING THE PLAIN BEAM Winding the Warp When winding the warp on from the back i e with the warp spread out in back of the loom turn the crank in a clockwise direction so that the warp comes in from the bottom PAPER LAYER WINDING ON Figure 15 WINDING THE WARP Remember wind the warp on tightly under a lot of tension This will vary with each warp material but a good rule to remember is that the tension of the wound on warp must be greater than the tension during the weaving operation You will need one person to hold a warp under tension on the back and one person to wind the warp on the beam using a handle The person winding the warp can also insert the paper For a wide heavy warp several helpers may be required Page 1 17 WARPING THE PLAIN BEAM Threading Cross Removing the Raddle Two Beams When do You Need to Tension Your Warps Separately Page 1 18 If you have to do it yourself you can use the jerking method Make one turn around with your beam crank and then go to the back of the loom and jerk
22. nsion 1 27 Combining Sectional and Plain Warping 1 27 THREADING SLEYING AND TYING ON 1 28 Preparation for Threading 1 28 Threading the Harnesses 1 29 Unused Heddles 1 29 Sleying the Reed 1 29 Tying on to the Apron 1 30 Tying on to an Old Warp 1 31 JACQPOINT INSTRUCTIONS JiP Files 1 32 Weave Menu 1 32 Options 1 32 Page 1 3 FIGURE INDEX Page 1 4 FIGURE 1 SIDE VIEW FIGURE 2 CONTROL UNIT FIGURE 3 FIGURE 4 FIGURE 5 FIGURE 6 FIGURE 7 FIGURE 8 FIGURE 9 FOOT PEDAL FIGURE 10 COMPU DOBBY FIGURE 11 CREATING TWO CROSSES FIGURE 12 FIGURE 13 FEEDING THE RADDLE FIGURE 14 PREPARED PAPER WITH FOLDED EDGE FIGURE 15 WINDING THE WARP FIGURE 16 WARP ROUTING FIGURE 17 TENSION BOX FIGURE 18 FIGURE 19 ATTACHING THE YARDAGE COUNTER TO THE TENSION BOX FIGURE 20 WARP ROUTING FIGURE 21 1 5 1 6 1 7 1 7 1 7 1 8 1 9 1 9 1 9 1 26 1 30 1 30 GETTING THE LOOM GETTING THE LOOM Congratulations on your purchase of an AVL Dobby Jacquard Loom It s time to get to know your loom Please read the manual before using the loom Figure 1 Side View reveals some of the major components Note your loom comes with two Jacquard heads and eight harnesses Each head includes 336 hooks that are connected to the heddles springs and a tie down rod Figure 1 SIDE VIEW Tension is set on the heddles while air pressure about forty p s i is ap
23. plied at the Heddle Tension Cylinder Later we will address warping the loom for now lets get the loom set up Page 1 5 CONNECTIONS CONNECTIONS The Control Unit houses the Integrated Circuit Boards that control the hooks Hooks on each head are arranged in twelve lines of twenty eight hooks per line Control Unit Figure 2 PLEASE NOTE THE NUMBERING SYSTEM STARTS WITH THE REAR LEFT HOOK as you re facing the loom MARKED AS HOOK 1 This is very important when you set up the loom and software Again rear left first row is hook 1 the last hook in row 1 is hook 28 located at the front of the row Rear left second row is hook 29 and so on Each set of fourteen hooks has a connection cable that is connected to the Control Unit Each row is numbered both on the Jacquard Head and at the Control Unit The Control Unit is connected to the controlling computer via a single RS 232 Cable Page 1 6 HEDDLES HEDDLES F a E Figure 3 Tat g A Each hook is connected to its own heddle Each heddle has a con tact tension spring that is tied at the bottom of the loom with the TIE DOWN BARS The Comber Strips may WL HY yy be spread farther apart H H H Uf YY or closer together to H Hi W Hi f decrease or increase Wy H UUA the number of ends per inch or centimeter The heddle spacer rods are used to keep the heddles at the correct height This is a very important concept NO MATTE
24. process if the new warp introduced into the loom uses the same threading pattern and E P I as the last warp This process is especially good for production weavers as it saves time It also takes less concentration and there is less chance of making mistakes in threading The tying on process starts when you are finishing the last warp on the loom Before you cut off the fabric make sure to leave enough unwoven warp to extend one foot behind the harnesses through the heddles and about six inches past the reed when the beater is in its rear position Now open two opposite tabby sheds and insert the lease sticks into these sheds behind the harnesses Secure the sticks together with tie tapes through the holes Now carefully cut the fabric from the loom and tie bundles of warp coming through the reed together so the yarn can t slip through Cut the warp in back leaving one foot past the lease sticks and also tie bundles of yarn together for security After winding on the new warp on the beam you can sit on a small stool placed in between the harnesses and the back of the loom and tie corresponding yarns from the two sets of lease sticks together An overhand or weaver s knot work well This may seem slow at first but you will work up a faster rhythm with some practice A good goal to reach would be to tie 200 to 250 ends together an hour When all ends are tied together go to the front of the loom and gently pull on the bundles of
25. rd Adjusting the Tension Device Attaching the Raddle Winding the Apron Attaching the Warp to the Apron Page 1 14 Remove the warp from the warping board by chaining or by winding on the kitestick Start from the threading cross and proceed to the raddle cross Since the capacity of the warping board is limited for wide warps you will end up making a number of mini warps and taking them off individually Before winding on the warp there are a few small things to take care of on the loom First check the tension device to make sure the rope is wrapped three times around the tension drum and that the rope end is clipped to the spring This will prevent the warp beam from slipping backwards during winding and threading Now secure the raddle to the back of the loom If you have an AVL raddle simply slip it into the set of holes in the back of the rear ver tical members Put your apron on the beam with velcro and wind your beam in the warping direction so that your apron is wound on the beam Bring the apron around the separation beam and put the metal rod through You can also put your warp section onto that rod or you can attach another one with the warp RADDLE SEPARATION BEAM WARP STICK SECURE THE WARP STICK TO APRON pee Bo in ROD WITH EVENLY SPACED TIES RSIS emt wilt We Figure 12 WARPING THE PLAIN BEAM Inserting Sticks in Place two lease sticks in the raddle cross and secure toge
26. s into a tight bundle with tie tapes or string to keep them from falling off the ends of the harness sticks or you may need to take heddles off the loom In the first six months of using a new loom with polyester heddles the heddles stretch out to adjust to the harnesses and the heddles on each harness get stretched out to different sizes For this rea son we do not recommend removing heddles from the loom for six months When heddles are removed they should be marked so they can be returned to the same harnesses For the same reason once the heddles have been on the loom for awhile it is not a good idea to switch heddles to different harnesses Mixing them up once they have been stretched would affect the evenness of the shed What some weavers do with wide warps in order to avoid having to take off extra heddles is to distribute the unused heddles among the threaded heddles as the threading is tak ing place Now sley the warp ends through the reed Some weavers start from the right side some from the left some in the middle But in all cases be sure to measure accurately before starting so that the warp will be centered in the reed or offset four inches to the right if the warp on the beam is already offset Weavers have various ways of positioning the reed for sley Page 1 29 THREADING SLEYING AND TYING ON Tying on the Apron Page 1 30 Now that you have your warp ends ready to tie we need to prepare the apron T
27. ther with the Raddle Cross string through the holes in the ends of the sticks Now remove the ties from the raddle cross and spread the warp out on the sticks Measure the center of your raddle to use it as a center of your warp The warp threads should either go through the middle of the raddle Feeding the Raddle To feed the raddle distribute yarns through the raddle by dropping each raddle cross group into a dent in the raddle If you are using an AVL raddle with a sliding cover slide it on after the raddle is threaded and secure it with two or three cord ties so it can t come off Remove the raddle cross sticks when this is com pleted RADDLE TOP USED AS THREAD SUPPORT APRON ROD is IN il u A RADDLE CROSS GROUP LEASE STICKS IN RADDLE CROSS Figure 13 FEEDING THE RADDLE Page 1 15 WARPING THE PLAIN BEAM Preparing the Paper Prepare the paper for winding between the warp layers Again Page 1 16 for the most professional results and fewer tension problems we suggest that the warp be as smooth tight and compact as pos sible This would mean not using corrugated paper or sticks as they will make the warp too fate and or lumpy Corrugated paper is just too soft and the warp can never be wound tight enough with it Heavy wrapping paper works well seventy pound craft paper is good If you are going to be using smooth slippery warp yarns like fine linens or perle cottons the edge yar
28. to lower of the pneumatic footswitch Depending on the Jacqpoint set up the Jacquard the Dobby or both will raise lower hooks harnesses The pneumatic footswitch switches air into the Dobby Lift Cylinder to force the cylinder plunger to retract thus raising the selected har nesses only if Dobby is selected Detection by the Lift Cylinder plunger Down position Reed Switch is interpreted by Jacqpoint as a command to activate the selected hooks to be raised FOOTSWITCH SENSOR WIRING FOOTSWITCH SENSOR WIRING The hooks will remain in their up position until the footswitch is activated a second time to cause air to extend the Dobby Lift Cylin der and the Up Reed Switch to sense movement at which time is interpreted by Jacqpoint to deactivate the hooks and also lower the harnesses if Dobby is selected If Dobby is not selected no harnesses will be raised If Dobby mode is activated then the harnesses lift at the same time as the hooks if in Simultaneous mode or the Jacquard hooks and har nesses alternate lifting the programmed picks if in Alternating mode If it is desired to execute a weaving pattern using the Dobby only then the Jacquard pattern must contain blank picks no hooks se lected Jacqpoint causes the action of the hooks harnesses based on detec tion of the Up and Down Reed Switches located on the Lift Cylin der Both Reed Switches are phys
29. ure 17 TENSION BOX Now let s go through the sequence for threading the tension box First move the two adjustable tension pegs up above the stationary pegs or remove them completely Now sley the thread through the rear stationary reed section using a sley hook Since this reed is eight dents per inch you will divide the E P I into eight to find out how many ends will be in each dent with sixteen E P I put two ends in a section If your E P I does not divide equally by eight you can either vary the number of ends in each dent with twenty E P I alternate two and three ends in the dents or thread the dents a little wider than two inches with twenty E P I put two ends in each dent with forty ends the reed will be sleyed 2 1 2 wide Page 1 23 WARPING THE SECTIONAL BEAM Page 1 24 Next bring the thread straight through the tension peg section in between the larger adjustable tension pegs and the smaller sta tionary pegs or just above the smaller stationary pegs if you have removed the larger ones Next thread the end through the two sets of heddles The first thread goes through the front set of heddles and the next thread goes through the rear set of heddles Repeat this alternating heddle threading for the rest of the ends The heddle system will be used later to create the threading cross Now thread the end through the front pivoting reed Here you have a choice of using an eight dent or ten dent reed Pick t
30. will cause the harnesses to drop too rapidly It is helpful to remove the breast beam the beater top and reed for the comfort The important thing in threading is your comfort Take the time to position everything so that your body feels at ease while threading THREADING SLEYING AND TYING ON Threading the Now we re ready to thread the loom If you are right handed it Harnesses Unused Heddles Sleying the Reed is recommended to start at the right side of the warp Grasp one group of ends in your left hand and your sley hook in your right hand Direct the hook end of the sley hook through the eye of the first heddle you need to thread Pull the thread through for example if you had a straight draft on eight harnesses your first thread would go through the eye of a heddle on the 8th harness The second thread would be threaded through the eye of the heddle on the 7th harness the third thread through the 6th harness and so on After threading is complete make sure that the unused heddles are all pushed to the far sides of the harness sticks between the screw eyes and the ends of the harness sticks For balance there should be approximately equal numbered groups of unused heddles on both sides of each harness This is especially the case if you have PES heddles In some cases such as a very wide warp with a lot of unused hed dles on the ends of the harnesses you may need to tie each group of unused heddle
31. yarn going through the reed to pull the new warp through the heddles and reed Then tie on to an apron Page 1 31 JACQPOINT INSTRUCTIONS J1P FILES WEAVE MENU OPTIONS Page 1 32 JacqPoint is a simple program the vast majority of comments are explained in the On Screen Help There are a few other key con cepts A number of different Jacquard programs can be accessed via J1P files They include 1 ArahWeave 2 JacCard Master 3 Pointcarre 4 ScotWeave 5 SOPHIS Each will save their files in a J1P format Then in FILE OPEN you should be able to open the file directly into JacqPoint Use Jacquard Options to set the Comm Port from your PC to the Control Unit Use Loom Control to start weaving Make sure you know your re peat In the Options Menu you must establish the size of your Point Paper in both Ends and Picks Picks are adjustable Ends should be set to the number of hooks in your system
32. ystems When weaving Very different size yarns Yarns with different stretching qualities Different densities Different structures Supplementary warp techniques because some warp threads do not interlace as often as others A group of special yarns for selvedges and borders Loops piles or puckers like seersucker More then one layer with different setts in each layer More than one layer with a different pick count in each layer Setting Two Beams More Than Two Warps Separate Tensioning WARPING THE PLAIN BEAM If you are confident in setting one beam it is just as easy to set up a loom with two beams It might take twice as much time and you do need to be more careful not to mix sequences Wind each warp on the beam the same way you would do it if there were only one beam on the loom plain or sectional Make a cross and have a pair of lease sticks with a cross in each warp Figure 16 WARP ROUTING Proceed with a threading as if you only had one beam one cross following your threading instructions and taking special care of which thread from which pair of lease sticks comes next If you have more than two warps to set and not more than two beams you need to weight tension your additional warps separately do the same if you only have one beam and more than one warp to set Make your warp sections on the warping board and take them off the board in a chain on a kite stick or just in a
Download Pdf Manuals
Related Search