Proshot Dual - www.camteq.com.au
Contents
1. Please ensure the communications window is clearly visible when initiating a survey or downloading survey data i e not covered or underground 1 Wireless communications window 6 Copyright 2009 Camtea All rights reserved MRK 00011 RA3 Menu Options Pairing The Proshot probe can be used with any Proshot handset by following the pairing process To pair a handset to a probe please follow these steps Press the lt Settings gt button Select Probe pairing from the menu Select Manual SN entry et a T Enter the probe serial number The probe serial number can be found engraved into the black centre piece Press lt OK gt 6 On successful pairing the display will show Connection to l probe successful The handset is now paired to the probe and can be used to conduct down hole surveys If you receive an error message while pairing please go to the No Response message section at the back of this user manual Survey Options The Proshot system provides a number of options to customise your down hole surveys These options can be changed in the Survey options menu Survey options include e Survey default name Change the default name of each survey to enable easy identification and to save manual entry at the beginning of each new survey e Start depth Set the default start depth for each survey 7 Copyright O 2009 Camtea All rights reserved MRK 00011 RA3 e Depth2. RA3 Changing batteries The Proshot has been designed to allow the user to change the handset and probe batteries Please note Batteries must be purchased from Camteg The use of unapproved batteries will void the product warranty and may damage the Proshot Dual s internal circuitry Handset To change the handset battery please follow these steps 1 Unscrew the six screws Gently open the handset disconnecting the keypad cable from the keypad connector 3 Disconnect the battery Remove the old battery and replace with the new battery 5 Connect the keypad cable and fasten screws Keypad cable Keypad connector Area reserved for battery B WN e Gasket seal channel Please ensure that the battery is secure with little movement and that the gasket seal is in place before fastening screws 16 Copyright 2009 Camtea All rights reserved MRK 00011 RA3 Probe To change the probe battery please follow these steps Unscrew the brass cover from the probe Loosen the grub screw 3 Disconnect the existing battery and replace with the newly supplied battery Fasten the grub screw 5 Pair to the probe with the handset to ensure the system is working correctly after battery replacement 6 Ensure O rings are in place and fasten brass cover lt INSERT PICTURES OF REMOVING BRASS BARREL CLAMPING PROBE AND USING SPANNER FLATS gt 1 Battery connector 2 Camteq approved battery 3 Wireless Communicat
3. gt to erase the survey data Please note Resetting the handset will not modify any of your custom survey settings 9 Copyright O 2009 Camtea All rights reserved MRK 00011 RA3 Zero Roll Adjust The Proshot probe can be zeroed to any roll angle To zero the Proshot probe please follow these steps 1 Pressthe lt Settings gt button Select Zero Roll Adjust from the menu 3 Press lt OK gt to perform a zero roll adjustment The probes ROLL will now read zero at the current position Please note The probe must be within communications distance from the handset to perform this function Ensure the handset is no more than 2 meters from the probe 10 Copyright O 2009 Camtea All rights reserved MRK 00011 RA3 Battery Level To check the battery level of the handset please follow these steps 1 Pressthe lt Settings gt button 2 Select Battery Level from the menu 3 Battery level will be displayed The following screen will be displayed Handset battery remain 100 Upload to USB The Proshot system supports the uploading of survey to a USB device Survey data is saved in standard CVS format allowing viewing in Microsoft Excel or any leading analysis package To save survey data to a USB key please follow these steps Press the lt Settings gt button Select Upload to USB from the menu 3 Insert USB device into USB port on front panel of the handset 4 Survey data will now be saved to the USB
4. 9 09 9 43 28 117 4 49 3 179 9 59 786 0 1 0 21 3 Table Example Please note The TotAcc column shows the total acceleration of the probe when the shot was taken A TotAcc of 1 0 means that the probe was stationary and the data is accurate If the TotAcc is greater or less than 1 0 the probe may have been moving or picking up vibrations from the string line this data maybe less accurate 14 Copyright 2009 Camtea All rights reserved MRK 00011 RA3 No Response message The Proshot system uses wireless technology between the handset and the probe This enables communication without the need for wires or for the user to disassemble the probe to download survey data In some circumstances the handset may not be able to communicate to the probe when this occurs the following screen is displayed No response from probe Press OK to retry or BACK to cancel This may be caused by a number of reasons If you see this message please review the following checklist and press lt OK gt to retry e Ensure the distance between the handset and the probe in no more than 2 meters e Ensure there are no obstacles between the handset and the probe e Ensure the communications window is clearly visible i e not covered or underground e After performing the above checks if you re still unable to communicate to the probe please check the batteries 15 Copyright 2009 Camtea All rights reserved MRK 00011
5. Interval Set the default depth interval for each survey shot e Direction of survey Select direction of the survey either into the hole or out of the hole e Single or Multi shot Ability to select probe shot mode Info To view the current software version of the handset or probe please follow these steps 1 Pressthe lt Settings gt button 2 Select Info from the menu 3 Select Handset Version or Probe Version The following screen will be displayed Handset Info SW version 4 4 1 0 2 DOS POS SN LESJA 8 Copyright 2009 Camteq All rights reserved MRK 00011 RA3 Date and Time To set the date and time of the Proshot system please follow these steps 1 Pressthe lt Settings gt button 2 Select Date and Time from the menu 3 Setthe date and time using the lt Arrow gt keys 4 Press lt OK gt when you have finished The following screen will be displayed Set Date and Time dd mm yy hh mm ss 03701700 ZO SG Pe Reset handset The Proshot handset stores survey data in memory for viewing or downloading to a USB key Even after downloading data to a USB key the survey data remains on the handset as a backup To erase stored survey data please follow these steps Press the lt Settings gt button Select Reset handset from the menu 3 The handset will display the following warning message If you reset handset all memory will be erased Press OK to reset 4 Press lt OK
6. Proshot Dual Multi shot surveying USER MANUAL CTPS100 This user manual explains how to use configure and maintain the Proshot system Please read and ensure you understand these guidelines before using the product Disclaimer While every effort has been made to ensure that the information contained in the guide is accurate and complete no liability can be accepted for any errors or omissions Camteq reserves the right to change the specifications of the hardware and software described herein at any time without prior notice No part of this guide may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form by any means without the prior written permission of Camteq Camteq make no warranties for damages resulting from corrupted or lost data due to mistaken operation or malfunction of the Proshot system 2 Copyright 2009 Camteq All rights reserved MRK 00011 RA3 Table of contents MN 5 FNS NL 5 HANG 5 PASSA Ol ODC EE E EE 6 META 7 PP epee oye tes tceense Seueco en beeace ra tevacorselencbva they etaeurerra eu eta enees 7 SUI VEY NN 7 oe a ad ee do S 8 DAS AA GL ae a S 9 RSS CVA SEE EN 9 Zero FO FAT lues a ess ann cause caen asc 10 PNAN 11 Upload Re eee 11 Starting a NEW SUFVEY cccccscccseccseccseccseceseceseceseceseccseetseecseetseetseetes 12 VIEWING TE NS 13 BEG EN EEE EN 14 No Response MESSABE sccsccsccnccnscnscnscosccsccsccscessens
7. csscaecascaecascens 15 ETEN 16 FAIS EEE RE EN 16 FP UO Soi EEE EE A 17 Calibration nd Handling icedontsecdcosnosdeorsaccdanoned teutenanasisnnnsabionnaantaveseds 18 3 Copyright 2009 Camtea All rights reserved MRK 00011 RA3 EEG NOT 0 FE 18 SSC IFC AU OWNS EEE NE E 19 4 Copyright 2009 Camtea All rights reserved MRK 00011 RA3 Introduction Congratulations You are using the latest in digital survey instrumentation for down hole exploration This user guide provides all the information you will need to use and care for your product Proshot System The Proshot handset provides wireless connectivity to any Proshot camera probe You can configure start a down hole survey and download survey data effortlessly Handset The Proshot handset layout and key button functions Proshot Dual gin Change survey settings Recover data from the probe View survey data stored on the handset Handset On Off button Turn on LCD backlight Navigation Keypad Take a survey shot Start a new survey USB interface LCD screen D Copyright 2009 Camteq All rights reserved MRK 00011 RA3 Proshot probe The Proshot probe is assembled as a single unit with two brass sleeves attached to a black centre piece the communications window The centre piece has the probe identification number engraved into it The communications window enables the probe to communicate to the handset using wireless technology
8. device The following screen will be displayed Saving data to USB storage Please wait 11 Copyright 2009 Camteq All rights reserved MRK 00011 RA3 Please note Do not remove the USB device from the USB interface until the handset is finished uploading data Starting a new survey To start a new survey simply press the lt New Survey gt button on the handset and follow the on screen instructions After pressing lt New Survey please follow these steps 1 Type in Hole ID Please type in the unique name of this Survey Press lt OK gt to initiate the survey 3 Press lt Take Measurement gt each time you wish to take a shot Do not move the probe while a shot is being taken Moving the probe will reduce the reliability of the survey data To take shot press TAKE MEASUREMENT To stop survey Press RECOVER DATA When the survey has been completed pull the probe out of the hole and press lt Recover Data gt The handset will now download survey data from the probe ready for viewing Please note The probe must be within communications distance from the handset to initiate a survey or to recover data ensure the handset is no more than 2 meters from the probe Once the survey has been initiated it is ready to be placed down the hole 12 Copyright 2009 Camtea All rights reserved MRK 00011 RA3 Viewing Survey data To view survey data press the lt View Data gt key and scroll through the survey shots u
9. ions window 4 Grub screw 17 Copyright 2009 Camteq All rights reserved MRK 00011 RA3 Calibration and Handling The Proshot camera probe has been calibrated to a high level of precision please see Specifications for more details The Proshot probe is a precision instrument and therefore should be treated with care Extreme temperatures heavy impacts severe vibrations or general misuse will affect the accuracy of the probe and may damage the internal circuitry It is recommended that the probe be returned for maintenance and recalibration every 12 months to ensure the highest precision and reliability possible Final Word Thank you for choosing the Camteg Proshot camera system The Proshot system has been designed for accuracy ease of use and low maintenance ensuring you get the maximum return on your investment If you have any queries or comments about the Proshot system or wish to learn more about our range of mining instrumentation please visit our website at www camteg com au We hope you enjoy using the Proshot camera system The Camteq Team 18 Copyright O 2009 Camtea All rights reserved MRK 00011 RA3 Specifications Proshot Camera Probe Ingress Rating It is recommended that the Proshot Camera is calibrated every 12 months to ensure accuracy is maintained Proshot Handset CTH100 Operational temperature 0 C to 60 C 32 F to 140 F 10 C to 120 C 14 F to 248 F A
10. lkaline battery Non rechargeable Wireless ISM 2 4GHz Ingress Rating IP65 2 years depending upon use NOTE Specifications subject to change without notice 19 Copyright 2009 Camtea All rights reserved MRK 00011 RA3
11. sing the arrow keys The following screens will be displayed as you press the lt Up gt and lt Down gt keys to view survey data Survey name Holel234 Depth 002 0 Time LASTES Azimuth 230 5 deg Dip X D 8 deg ROLL 324 3 deg Temp C 25 6 Total Mag 56432nT Total Acc T Press the lt Left gt and lt Right gt keys to scroll through the surveys stored on the handset 13 Copyright 2009 Camtea All rights reserved MRK 00011 RA3 Data Analysis Survey data can be downloaded to a USB device for further analysis The data is stored in CVS format and can be imported into any spreadsheet software for analysis The below table is an example of the data layout when imported into a spreadsheet SN Name Depth Date Time Azi Dip Roll TotMag TotAcc Temp 7 w Q Q Q Q 3 333Q Q2Q2 Z a N N N N J 3 U 33 Z Z J q q O q q q 3Q3Q 3 3 3 3 3 q 3zCCC Z Z Zq Q Q Q AZ Z Z Z Z Cnhn nz zz q q q q q22ZqCZZZ 220 C 47 4Q 220022 2000000000000000r00nnnoodnnnnnnnnnnnnnnnnnnnnnonnnned 5031 Holel Oa 17 09 09 9 42 30 116 9 49 2 68 59 835 4 10 211 Jerr traning ener bene CESSER SEEENEENEENEN EEE eEUE CTETEEEET TEE EIRE ENT ENETEETEEENEEENEE om SA EEE ERP 5031 Holel 30a 17 09 09 9 42 58 117 2 49 3 276 8 59 857 1 I 10 212 60a 17 0
Download Pdf Manuals
Related Search