DVI Detective
Contents
1. LI 7 N IGEFEN i DVI Detective Prog DVI In Power tm page 2 Getting Started DVI Out WR Prog DVI In Power Introduction Description Connect the DVI display to this port using a DVI cable Write enable switch Flip this switch to the E position to allow the DVI Detective to be programmed with an external EDID Set this switch to the D position to disable programming and prevent an accidental erasure of the current EDID Press this button to begin programming an EDID See EDID Programming page 8 for more information Connect the DVI source to this port using the included DVI cable This LED will glow bright red when the unit is powered page 3 Installation Connecting the DVI Detective Stop Before connecting the DVI Detective the unit must be programmed with an EDID See for more information before continuing with the installation Getting Started 1 Connect the included DVI cable from the DVI source to the DVI In port on the DVI Detective 2 Use another DVI cable to connect the display or other sink to the DVI Out port on the detective 3 Power on the display sink device and the source The included 5V DC power supply is not required Sample Wiring Diagram DVI CABLE a Computer e DVI Detective N EXT DVI2. Customers outside the US are responsible for shipping charges to and from Gefen Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com Contacting Gefen Fee hekse Technical Support 818 772 9100 800 545 6900 8 00 AM to 5 00 PM Monday Friday Pacific Time Fax 818 772 9120 Email support gefen com Web http www gefen com Mailing Address Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 Product Registration Register your product here http www gefen com kvm Registry Registration jsp Operating Notes This page left intentionally blank DVI Detective is a trademark of Gefen LLC O 2015 Gefen LLC All Rights Reserved All trademarks are the property of their respective owne
3. EDID 8 The EDID programming process is complete 9 See Connecting the DVI Detective page 4 page 8 Basic Operation LED Stan The Power Link LED indicator on the DVI Detective provides basic information on the current status Status Description Solid red e The 5V DC power supply is connected to the DVI Detective e The DVI Detective is connected between the source device and the display sink device Flashes red QUIS The DVI Detective is being programmed with an EDID Ss DVI Detective 3 Appendix Specifications Specifications Formats 3840 x 2400 Dual link 2048 x 1080 2K 1920 x 1200 WUXGA Appendix DVI In 1 x DVI I 29 pin female DVI Out 1 x DVI I 29 pin female Programming 1 x Push button momentary switch Write protect switch O 1 x two position slide switch Power G 1 x LED red Maximum Pixel Clock 2 x 165 MHz Power Input o 5V DC Power Consumption 5 Watts max Operating Temperature 41 to 113 F 5 to 45 C Physical Dimensions W x H x D 2 6 x 1 8 x 1 2 66mm x 46mm x 30mm Unit Weight 0 18 Ibs 0 08 kg page 12
4. EDIDN page 4 DVI Detective 2 Basic Operation EDID Rrogrammingi feet 8 EE DES Lats tier Eee een 9 Basic Operation EDID Programming Before using the DVI Detective the unit must be programmed with an EDID In most cases the DVI Detective should be programmed with the EDID of the display or other sink device to which you are connecting the source Once programmed the EDID data will be read by the source providing all the necessary details of the type of signal that the display or other sink device can process Although any DVI Detective can be programmed with any EDID the display or other sink device must be able to support those features 1 Begin by powering on the display or other sink device containing the EDID to be recorded 2 Connect a DVI cable from the sink device to the DVI Out port on the DVI Detective 3 Move the WR switch to the E position in order to allow the EDID to be written to the DVI Detective EXT D ana DVI Out TL E 4 Connect the included 5V DC power supply to the DVI Detective The Power LED on the other side of the unit will glow solid red 5 Press and release the Prog button The Power LED will flash as the EDID is recorded pa o E 6 Once the EDID has been recorded the Power LED will glow bright red 7 Move the WR switch to the D position to prevent accidental erasure of the
5. GEFEN DVI Detective EXT DVI EDIDN User Manual Release A3 Important Safety Instructions 10 11 12 13 14 15 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this product near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install or place this product near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer To reduce the risk of electric shock and or damage to this product never handle or touch this unit or power cord if your hands are wet or damp Do not expose this product to rain or moisture Unplug this apparatus during lightning storms or when unused for long perio
6. ds of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Batteries that may be included with this product and or accessories should never be exposed to open flame or excessive heat Always dispose of used batteries according to the instructions Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty
7. rs Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice Gs X CE O This product uses UL or CE listed power supplies Features and Packing List Features Quick and easy way to store EDID information from any DVI display hd Provides a virtual EDID to maintain active monitor status when switching away from a source Supports resolutions up to 1920x1200 2K and 3840x2400 Dual Link EDID write protection switch No power is required after initial programming Packing List The following items are shipped with the DVI Detective If any of these items are not present in the box when you first open it immediately contact your dealer or Gefen 1 x DVI Detective 1 x 1 ft Dual Link DVI Cable M M 1 x 5V DC Power Supply 1 x Quick Start Guide vi Table of Contas Getting Started Introduction en 2 Installation Connecting the DVI Detective cha alia sample Wiring Diagram 100 iaia 4 Basic Operation EDID Programming une aAa NE ehren rennen erregen 8 FED O AN 9 Appendix A SEE EET ER are EEN ATAT AAE HEUT ED EEES REEL rasa 12 viii DVI Detective E3 Getting Started Introduction ene iaia EAE 2 E A nn 4 Connecting the DVI Detective maa a aaa 4 Sample Wiring iaa 4 Introduction T dk DVI Out EXT DVI EDIDN Getting Started
Download Pdf Manuals
Related Search