USB-FRM02 User`s Manual
Contents
1. JP1 Connector JP1 connector is used for the FPGA program upgrade Never use it at the normal operation Figure 4 7 shows the JP1 connector JP1 O Figure 4 7 JP1 Connector Top View 18 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 JP2 Connector JP2 connector is used for FPGA functional test Never use it at the normal operation Figure 4 7 shows the JP2 connector JP2 O O Figure 4 8 JP2 Connector Top View JP3 Jumper JP3 jumper should be shorted when upgrading FPGA program Never use it at the normal operation Figure 4 9 shows the JP1 connector JP3 Figure 4 9 JP3 Jumper Top View JP4 Jumper JP4 jumper determines the status of write protection of the EEPROM It is recommended that JP4 be open at the normal operation Figure 4 10 shows the JP4 jumper JP4 Figure 4 10 JP4 Jumper Top View OPEN Write protection Normal status SHORT Writing possibility 19 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 4 4 Sample Program A sample program is provided to make the user get familiar with the board operation and to make the program development easier You can find the sample program in the CDROM Before using it you have to install the board and its driver in your computer properly Sample program is provided in source form in order to show the usage of API Applicat2. Universal Serial Bus Specification Compaq Intel Microsoft NEC MindShare Inc Addison Wesley 3 AN201 How to build application using API DAQ system 4 AN342 USB FRMO02 API ver1 0 DAQ system 27 http www daqsystem com
3. 3 Installation After unpacking inspect the board to make sure there are no damages on the package 3 1 Package Contents ll Figure 3 1 USB FRMO2 product contents Product Contents 1 USB FRMO2 Board 2 USB A B Cable 3 CD Driver Manual API Samples etc 3 2 Installation Sequence To install USB FRMO2 board in your environment do the following steps The USB FRMO2 board is completely Hot Plug and Plug amp Play Therefore you can install it easily The required PC operating system for the USB FRMO2 is Windows 2000 SP4 or Windows XP SP1 higher The USB FRMO2 uses USB High Speed interface thus USB 2 0 Root Hub should be installed in your PC You can check this condition by doing the following steps My Computer gt Properties gt Hardware gt Device Manager gt Universal Serial Bus controllers 6 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 a ld Open Explore Search Manage Map Network Drive Disconnect Network Drive Create Shortcut Delete Rename Properties wy Figure 3 2 Select My computer gt Properties System Properties System Restore Automatic Updates Remote General Computer Name Hardware Advanced Device Manager The Device Manager lists all the hardware devices installed on your computer Use the Device Manager to change the properties of any device Drivers Driver Signi
4. on the board you must wait until the completion of data acquisition 5 LVDS Close button Press this button to finish usage of the board and terminate the program 6 Save to button When press this button it saves the frame data as a file on disk 4 4 2 Functions related to UART 1 Send Serial Data button and editor box Press this button to send the serial data in the editor box to the frame grabber through UART interface You can directly write the data in the editor box beside the button 2 Get Serial Data button Press this button to get the serial data from the frame grabber If there is received serial data from the frame grabber it will be displayed in the editor box below the button 3 Clear Serial Data button Press this button to clear the contents of the editor box 21 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 4 Start Timer button Press this button to start the timer The sample program will read the UART data The reading interval is around 100ms 5 Stop Timer button Press this button to stop periodical reading of UART data 6 UART Init button Press this button initialize UART It must be performed only once after power is applied to the board 7 UART Close button Press this button to finish usage of the board and terminate the program 4 4 3 Functions related to DIO 1 DIO Read butto
5. to save Image Frame data from Image Frame Simulator on the USB FRMO2 23 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 board 2 Press the Frame Read button Then data are displayed on editor box Compare the contents of the editor box with the data of Image Frame Simulator Comparison can be performed using the Save to button It saves the contents of the editor box to a file 5 2 UART Tx Rx Test At the above figure 4 11 the Image Frame Simulator send to serial data to the board periodically 1 Press the UART init button to initialize the UART and then press the Start Timer button to get the UART data from the Image Frame Simulator Then the gotten data are displayed on the editor box below button Compare the contents of the editor box with the data of the Image Frame Simulator 2 Write a data to the editor box beside the Send Serial Data and press button to send it to the Image Frame Simulator via the UART Compare the data on the editor box with that of the Image Frame Simulator 5 3 DIO Input Output test At the above figure 4 11 write a OxFFF to the editor box of the DIO Direction button and press button to make all ports being output mode 1 After to make all output port 1 using DIO Write function of the test program check the output state using the oscilloscope or check the write data using DIO Read function And then a
6. 800F900F AOOFBOOFCOOFDOOFEOOFF NNNNNZPNANNALNANNLNILNLNZNLNSNLNANINSNILNRANLNAFNLNANLNANLNANINRNALNCNLANNLAOFNLNAF Send Serial Data Get Serial Data Clear Serial Data Start Timer Stop Timer UART Init UART Close DIO Read j DIO Write DIO Direction Figure 4 11 Main window of the sample program To run the sample application program you need to use API Application Programming Interface which is a form of client DLL Dynamic Link Library To compile the sample source to make its executable file you have to use Import Library files and header files You can find them in the CD ROM To run the execution file the API DLL USB_FRMO2 DLL must be in the same directory with the execution file or in Windows system folder Another method is to add the directory of API DLL file to PATH environmental variable 20 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 4 4 1 Functions related to image frame 1 DXD810 DXD1417 Combo box Use this box to select the operation mode DXD810 mode or DXD1417 mode 2 LVDS Init button When press this button it initializes the function of receiving image frame data It is performed only once after power is applied to the board 3 Start button When press this button it start to save the image frame 4 FRAME Read button When press this button it reads the image frame data saved image frame If image data is not saved
7. DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 USB FRM02 User s Manual ECTE Windows Windows2000 Windows NT and Windows XP are trademarks of Microsoft We acknowledge that the trademarks or service names of all other organizations mentioned in this document as their own property Information furnished by DAQ system is believed to be accurate and reliable However no responsibility is assumed by DAQ system for its use nor for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or copyrights of DAQ system The information in this document is subject to change without notice and no part of this document may be copied or reproduced without the prior written consent Copyrights 2005 DAQ system All rights reserved uM http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 Contents 1 Introduction 2 USB FRM02 Functions 3 Installation 3 1 Package Contents 3 2 Installation Sequence 4 USB FRMO2 Description 4 1 USB FRMO2 Layout 4 2 Description of the functional blocks 4 3 Connector Pin out 4 4 Sample Program 5 Test 5 1 Image Frame Test 5 2 UART Rx Tx Test 5 3 DIO Test Appendix A 1 General Specification A 2 Physical Dimension Reference 2 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 1 Introduction The USB FRMO2 is a board to receiv
8. ce driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware Con Ce Ca Figure 3 6 Specify the driver folder 9 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 Select Search for the best driver in these locations Check Search removable media floppy CD ROM Check include this location in the search Click Browse button Select the folder where the drivers are located Click OK Click Next Figure 3 7 will be shown The necessary files are usb_frm02 inf and usb_frm02 sys in the driver polder Found New Hardware Wizard Please wait while the wizard installs the software eS SS fa DRtech USB2 0 High speed Frame Grabber 5 5 Figure 3 7 Device Manager window When you across a window s warning message regarding to the compatibility problem as shown the Figure 3 8 during the installation process just click Continue button and go on the installation A The software you are installing for this hardware DRtech USB2 0 High speed Frame Grabber has not passed Windows Logo testing to verify its compatibility with Windows P Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop t
9. e data from Camera Link modulator or Image device 3 3 V CMOS Camera and transmit the received data to the system via USB2 0 interface High speed 480Mbps In addition it has a 16 general purpose digital inputs and outputs for external controls The operation of the board is controlled by API Application Programming Interface Program which can be easily installed into your PC It has two operation modes One is DXD810 2048 x 1536 resolution mode and the other is DXD1417 3160 x 2564 resolution mode The difference between two modes is only the image resolution You can select its operating mode by using the API functions Figure 1 1 shows connection of the PC with a USB FRMO2 board equipped into the frame grabber USB FRMO02 Board Camera Link Modulator USB2 0 Interface Figure 1 1 USB FRMO2 Board Usage As shown in Figure 1 1 it receives image frame from the 3 3V CMOS interface and transmits the received data to the system via high speed USB2 0 interface 3 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 5555559 khs e g ba a Figure 1 2 Picture of the USB FRMO2 Board Figure 1 2 shows physical connection of the board USB FRMO2 At the left side there is USB B type connector J1 for communication with your PC The 24 pin connector J4 at the upper right side is for General purpose I O 24 pin connector J5 at the lower side is for UART communication and f
10. gain to make all output port 0 using DIO Write function of the test program check the output state using the oscilloscope or check the write data using DIO Read function 2 Write a 0x0 to the editor box beside the DIO Direction button and press button to make all output being input mode Each port pulls up or pulls down through 4 7K resistor and then checks all ports using DIO Read function 24 http www daqsystem com DAO SYSTEM USB FRM02 Users Manual Rev 1 1 Appendix A 1 General Specification Specification General e USB 2 0 Specification e High Speed Device 480Mbps e 8051 Compatible Instruction Set 4 Clock per Cycle e 32MB SDRAM Interface e 5V Single Power operation Max 300mA under e 3 3V CMOS 16bit General Purpose I O e 3 3V CMOS Camera Link Interface e 14bit Image Frame Acquisition Functions e Transmit Image Frame Data to PC e 9600bps UART Rx Tx Software Supported OS Windows 2000 SP4 and Windows XP SP1 above API Interface with Application through client DLL Sample Software Test Sample software for evaluation 25 http www daqsystem com DAO SYSTEM USB FRM02 Users Manual Rev 1 1 A 2 Physical Dimension 89 lt Top View gt 15 5 wf rrm alae 3 0 16 lt Right Side View gt 26 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 References 1 USB 2 0 System Architecture Don Anderson USB SIG www usb org 2
11. his installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Figure 3 8 Warning window 10 http www daqsystem com DAD SYSTEM USB FRMO2 Users Manual Rev 1 1 If the installation is completely finished a completion window message shall be shown as in Figure 3 9 Click Finish Completing the Found New Hardware Wizard The wizard has finished installing the software for DRtech USB2 0 High speed Frame Grabber Click Finish to close the wizard Figure 3 9 Completion message window If you successfully complete the wizard you can find the item DRTech USB2 0 High speed frame grabber in the Device Manager window as shown in Figure 3 10 Device Manager TBR File Action View Help 7562 Sound video and game controllers See Storage volumes USB Root Hub gt USB Root Hub USB Root Hub VIA Rev 5 or later USB Universal Host Controller gt VIA Rev 5 or later USB Universal Host Controller VIA Rev 5 or later USB Universal Host Controller gt VIA Rev 5 or later USB Universal Host Controller gt VIA USB Enhanced Host Controller Figure 3 10 Device Manager window ll http www daqsystem com DAG SYSTEM USB FRM02 Users Manual Rev 1 1 4 USB FRMO2 Description In this chapter the primary functions of the board are described briefly For m
12. ion Programming Interface of the board and may be modified for customer s own usage Frame Test Application Program g 0 x TSF BAe SOY T amp g amp H Dad elg 00000000 00000001 0002000300040005000600070008000900040006000CO00D000E000F oxo z 00000020 001 0001 1001 2001 3001 40015001 6001 7001 8001 9001 4001 B001 C001 D001 E001 F 00000040 00200021 0022002300240025002600270028002900240028002C002D002E002F LVDS Init QOOOON60 00300031 003200330034003500360037003800390034003B003C00SD003E003F Sn 00000080 00400041 004200430044004500460047004800490044004B004C004D004E004F Start 00000040 005000510052005300540055005600570058005900540056005C005D005E005F D00000C0 00600061 006200630064006500660067006800690064 006B006CO06D006E006F FRAME Read 000000E0 00700071 007200730074007500760077007800790074007BOO7COOTDOOTEOOTF 000001 00 00800081 0082008300840085008600870088008900840086008C008D008E008F _LVDS Close 000001 20 00900091 0092009300940095009600970098009900940098009C009D009E009F 000001 40 00400041 00420043004 400450046004 7004800490044004B004CO04D004E004F 000001 60 00800061 OOB2Z00B300B400B500B600B700B800B900B4 0OBBOOBCOOBDOOBEOOBF 000001 80 00CO00C1 00C200C300C400C500C600C700CE00CI00CAQOCE0OCCOOCDOOCEQOCF Save to 000001 40 00D000D1 00D2000300040005000600070008000900D4 00DB00DC00DD00DECODF 000001 CO 0DE000E1 00E200E300E400E500E600E7T00E800E900EA Q0EB0OECOOEDOOEEOQEF 000001 E0 COFOOOF1 QOF 200F 300F400F500F600F 700F
13. its pin description 5 48 a3 44 D 40 D DG 0 Figure 4 5 J4 Connector Top View 15 http www daqsystem com DAQ SYSTEM Table 2 J4 PIN OUT Description USB FRM02 Users Manual Rev 1 1 Pin Signal Name Description Remark 1 10_00 General Purpose I O 00 3 3V CMOS Logic 2 10_01 General Purpose I O 01 3 3V CMOS Logic 3 10_02 General Purpose I O 02 3 3V CMOS Logic 4 10_03 General Purpose I O 03 3 3V CMOS Logic 5 10_04 General Purpose I O 04 3 3V CMOS Logic 6 10_05 General Purpose I O 05 3 3V CMOS Logic 7 10_06 General Purpose I O 06 3 3V CMOS Logic 8 10_07 General Purpose I O 07 3 3V CMOS Logic 9 10_08 General Purpose I O 08 3 3V CMOS Logic 10 10_09 General Purpose I O 09 3 3V CMOS Logic 11 10_10 General Purpose I O 10 3 3V CMOS Logic 12 10_11 General Purpose I O 11 3 3V CMOS Logic 13 10_12 General Purpose I O 12 3 3V CMOS Logic 14 10_13 General Purpose I O 13 3 3V CMOS Logic 15 10_14 General Purpose I O 14 3 3V CMOS Logic 16 10_15 General Purpose I O 15 3 3V CMOS Logic 17 N C No Connection Never Use this pin 18 N C No Connection Never Use this pin 19 N C No Connection Never Use this pin 20 N C No Connection Never Use this pin 21 GND Board Ground 22 5V Board Power 5V 23 GND Board Ground 24 5V Board Power 5V 16 http www daqsystem com DAO SYSTEM USB FRMO2 Users Manual Rev 1 1 J5 Con
14. kes a circuit for the FPGA 13 http www daqsystem com DAO SYSTEM USB FRMO2 Users Manual Rev 1 1 4 3 Connector Pin out The board has several connectors and jumpers to set J1 Connector Jl is a USB B type connector for high speed USB connection Figure 4 2 and Table 1 shows the J1 connector and its pin description 2 1 3 4 24 4 2 Jl Connector USB B type Front View Table 1 USB B Connector Pin Signal Name Description Remark 1 VCC USB power 5V Not used 2 D USB signal Minus Negative 3 D USB signal Plus Positive 4 GND USB power GND J2 Jumper J2 24 4 3 J2 Jumper Top View The USB FRMO2 board has powered through J5 s flat cable at normal operation However when the board is tested alone a short pin can be installed on J2 pins and the power can be drawn from PC through USB connector Important notice Never install J2 jumper while J5 flat cable is connected It can be damaged PC 14 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 J3 Connector J3 is used for the board self test or the production line Do not use at the normal operation Figure 4 4 shows the J3 connector J3 O Figure 4 4 J3 Connector Top View J4 Connector J4 is a 24 pin header for general purpose I O The I O direction of each pin is determined by API Figure 4 5 and Table 2 shows the J4 connector and
15. n Press this button to read the data on General purpose I O ports The I O status is displayed on the editor box 2 DIO Write button Press this button to write the data in the editor box to General purpose I O ports 3 DIO Direction button Press this button to determine the I O direction of General purpose I O ports If you write O to the right empty box the port will install the input port Otherwise the port will install the output port For example if you write the value Ox0001 in the editor box port O shall be output port and the rest of the ports shall be input port 22 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 5 Test 5 1 Image Frame Test In this chapter the functional test will be explained It is performed by the sample program FrmTest exe on the PC equipped with the USB FRM02 board Comnector J1 Image Frame Simulator Power and Image Data Figure 5 1 Equipment connection for the test Figure 5 1 shows the connection of the equipments The USB FRMO2 board receives power and image data from Frame Data Generator Simulator After completion of connecting the necessary materials power up and execute the test program FrmTest exe on your PC Follow the steps to test the function of receiving image frame data 1 Press the LVDS init button to initialize the LVDS circuit and then press the Start button
16. nector J5 is a 24 pin header connector for receiving the image frame data and supplying the power to the board It also has the pins for UART communication Figure 4 6 and Table 3 show the J5 connector and its pin map 43 04 a 42 49 Q O Figure 4 6 J5 Connector Top View Table 3 J5 Connector Pin Description Pin Signal Name Description Remark 1 DATAOO Frame Data 00 3 3V CMOS Logic 2 DATAO1 Frame Data 01 3 3V CMOS Logic 3 DATAO2 Frame Data 02 3 3V CMOS Logic 4 DATAO3 Frame Data 03 3 3V CMOS Logic 5 DATA04 Frame Data 04 3 3V CMOS Logic 6 DATA05 Frame Data 05 3 3V CMOS Logic 7 DATA06 Frame Data 06 3 3V CMOS Logic 8 DATA07 Frame Data 07 3 3V CMOS Logic 9 DATA08 Frame Data 08 3 3V CMOS Logic 10 DATAO9 Frame Data 09 3 3V CMOS Logic 17 http www daqsystem com DAD SYSTEM USB FRMO2 Users Manual Rev 1 1 11 DATA10 Frame Data 10 3 3V CMOS Logic 12 DATA11 Frame Data 11 3 3V CMOS Logic 13 DATA12 Frame Data 12 3 3V CMOS Logic 14 DATA13 Frame Data 13 3 3V CMOS Logic 15 HSYNC Horizontal sync 3 3V CMOS Logic 16 VSYNC Vertical sync 3 3V CMOS Logic 17 CLOCK Frame clock 20Mhz 3 3V CMOS Logic 18 LDV Line Valid not used 3 3V CMOS Logic 19 RXD UART Receive 3 3V CMOS Logic 20 TXD UART Transmit 3 3V CMOS Logic 21 GND Board Ground 22 5V Board Power 5V 23 GND Board Ground 24 5V Board Power 5V
17. ng lets you make sure that installed drivers are compatible with Windows Windows Update lets you set up how Windows connects to Windows Update for drivers Hardware Profiles Sie Hardware profiles provide a way for you to set up and store 2 different hardware configurations Hardware Profiles Figure 3 3 Select Hardware gt Device Manager 7 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 Device Manager File Action view Help gt fH ae s ER Processors 4 Sound video and game controllers ME system devices gt Universal Serial Bus controllers gt USB Mass Storage Device gt USB Mass Storage Device USB Root Hub gt USB Root Hub gt USB Root Hub USB Root Hub B Root Hub gt VIA Rev 5 or later USB Universal Host Controller gt VIA Rev 5 or later USB Universal Host Controller gt VIA Rev 5 or later USB Universal Host Controller gt VIA Rev 5 or later USB Universal Host Controller VIA USB Enhanced Host Controller Figure 3 4 Device Manager window The item USB 2 0 Root Hub should be shown in the Device Manager window as shown in Figure 3 4 After checking the PC environmental conditions for USB FRMO02 do the following steps to install the board 1 Install the USB FRM02 board into your system 2 Power on the frame grabber 3 Confirm the LED D1 and LED3 on the USB FRMO02 board turns on 4 Connect USB A B cable between the ca
18. ore information refer to the device specification 4 1 USB FRMO2 Layout USB FRM02 Board J7 USB FRM02 U3 Rev ua oa000000 000200 0000000000000 JI vt o o o o o oO oO o o o O ooo0o0oo00o000000 0000000000000000 sesonnne DAQ system poioman U10 www daqsystem com 000 us ecoco0o00 COC 00 oo0000000000 Figure 4 1 USB FRMO2 PCB layout The board has four LEDs to indicate the operation status D1 turns on when power is applied to the board LED1 turns on whenever the board receives the frame image data LED2 turns on whenever the board is transmitting the received frame image data to your PC LED3 turns on when power is applied and the FPGA is ready to run 12 http www daqsystem com DAQ SYSTEM USB FRM02 Users Manual Rev 1 1 4 2 Description of the functional blocks 1 FPGA All of the functions are controlled by the logic program of the FPGA 2 USB2 0 SIE This block supports USB2 0 High speed interface 3 EEPROM The EEPROM contains 8051 firmware for USB2 0 SIE 4 SDRAM The SDRAM is for saving the image frame data The size of one frame data is 6MByte for DXD810 mode and 16MByte for DXD1417 mode 5 Regulator The Regulator is for supplying the power 3 3V to the board 6 Level Shifter It is protected a circuit that the interface of high voltage higher than 3 3V CMOS Logic is exchanged to normal 3 3V Logic Level 7 EPLD The EPLD ma
19. rame data channel 4 http www daqsystem com DAD SYSTEM USB FRMO2 Users Manual Rev 1 1 2 USB FRMO2 Functions As shown in the following figure main control of the board is performed in FPGA Core Logic The primary functions are receiving the frame data transmitting receiving UART data and controlling general purpose I O These functions are performed by using API through USB 2 0 interface at the PC The board has 32MByte SDRAM for buffering the frame data USB FRM02 USB High Speed 16 Bit I O Device 2 0 I O Interface Specification Interface 4K Byte USB FIFO FPGA Core Logic 32M Byte Cpmmunication SDRAM FPGA Program a Logic p 14 bit Frame Data Figure 2 1 USB FRM02 Functional block Diagram Programming FPGA Core Logic is performed via the JTAG interface The logic program of the FPGA is saved in a flash ROM it is located on the board and loaded at the power up time Features of the USB FRM02 Board e USB 2 0 Specification High speed 480Mbps device e 32MB SDR SDRAM for buffering the Frame Data e Single 5V operation e Receiving 14 bit frame data acquisition e UART communication 8 bit data 1 start 1 stop No parity 9600bps e 16 bit General Purpose I O e Windows 2000 SP4 or Windows XP SP1above e Convenient Windows Application Programming Interface DLL 5 http www daqsystem com A ESAE sysrem USB FRM02 Users Manual Rev 1 1
20. se and your PC a a The Add New Hardware Wizard will appear in order to install the driver for new hardware 5 The Add new Hardware Wizard will install the driver in the following process The following install process is explained based on Windows XP operating system 8 http www daqsystem com DAD SYSTEM USB FRMO2 Users Manual Rev 1 1 This wizard helps you install software for USB Device If your hardware came with an installation CD y lt 3 or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Figure 3 5 Hardware Wizard window If new hardware is found Wizard will ask you to install the corresponding driver For installation of the driver select item Install from a list or specific location Advanced and click Next as in the Figure 3 5 Please choose your search and installation options Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed Search removable media floppy CD ROM Include this location in the search D A CDROM_USB_FRMO1_REV1 Driver Don t search will choose the driver to install Choose this option to select the devi
Download Pdf Manuals
Related Search