User Manual
Contents
1. 8 John IN Shot count 5000 MpX 97 17 www kme no User Manual Monitor and SDU 6 1 Shots value and hit marking In the column to the right the shots value is displayed Each value is divided into 10 levels the number after the period where 9 is in the inner rim of the circle and 0 is in the outer rim of the circle Usually the outer 10 and the inner 10 will be combined on the decimals so that the outer 10 goes from X 0 to X 4 and the inner 10 goes from 5 to 9 The best inner 10value is 9 The following symbols are used to display the shots value Symbol Value of shot fired Shot value 1 to 9 Outer 10 5 Inner 10 NB These values are only valid for the most common 10 divided targets Targets with other level dividing and figures have different rules when it comes to decimals and center hits NB If Show shot is set to Fixed there is no connection between the size of the hit marking the drawing of the shot and the gauge that is used for calculating the shots value The size is selected to give a best possible visual image regardless of the gauge size If Display hit is set to Fixed the visual image of the shot will be displayed in the same size as the gauge with respect to the target size 6 2 Average hit point The average hit point is displayed as a square with a cross in the centre The coordinates for the average hit point will be displayed in the lower right c2. MpX 97 7 www kme no User Manual Monitor and SDU 5 START UP 5 1 Power supply 5 1 1 Power model 1 Use the switch to turn the unit on off 5 1 2 Power model 2 and 3 This types of power does not have an of off switch so the net cord has to be connected disconnected to turn the unit on off Both units are equipped with self resetting fuses overload protection MpX 97 8 www kme no User Manual Monitor and SDU 5 2 The Monitor The Monitor has no on off switch but starts automatically when the power is turned on or the cable is connected Check the contrast setting if no image appears in the display it can take up to 30 seconds before the program starts up Since there is no on off switch there is an added function to restart the monitor without removing the cable or switching off on the power supply By pushing the menu button down to the right simultaneously with the menu button down to the left see picture the monitor will restart At first when the monitor is turned on the display light is weak It will grow stronger as the display heats up Often the contrast has to be adjusted as the display gets warmer to secure optimal contrast on the display 5 3 First time The Monitor and the Signal Distribution Unit SDU will at delivery not have any targets programmed and the software will not be the latest version Enclosed is one or two floppy disks marked UPGRADE If there are two floppy disks
3. 8 3 3 Target zero point 8 3 4 JE M SDU SETUP NER 0 4 POLE TIN Cotes es m Mee AN E RR re ate a MEd a Ras Son Ai mn Kn AT 094 2 PYOLOCOL And Donnie ete e MEE RERUMS Ee oP EROS S DELETE SHOT COUNTERS ee Ree tee leet tic ise Gece 9 SOFTWARE UPGRADE UR 35 9 T SYSTEM AMODE etes treten ist tee ien tet itta ttti ib dts 36 9 24 NORMALE STARTZ2UP te eee tte cet tute eet s veles teresa to Mas VO deese eb ret PET eie 36 MpX 97 3 www kme no User Manual Monitor and SDU 1 THE MONITOR Keyboard Menu buttons Smart card The Smart card is inserted in the slot on the right side of the display Make sure that the contact points are turned towards the back of the monitor MpX 97 4 www kme no User Manual Monitor and SDU 2 SIGNAL DISTRIBUTION UNIT SDU MODELS We have two different models of the SDU 2 1 The SDU 1 Model Connector for PC connection Smart card reader Kongsberg N Spectator display LED GPS Printer contact Floppy disk unit for upgrading software MpX 97 5 www kme no User Manual Monitor and SDU 2 2 The SDU 2 Model Power Status Status lamp Radio transmit indicator lamp Only on radio Radio transmit indicator lamp Only on radio version ble o Transmit
4. 72497 Insert smartcard Y The users must have a smart card User Card to log on if the User Card has been programmed for a limited number of shots the number will be counted down for each shot fired When the card is empty the system will stop marking If the card is removed or pops out by itself a warning will be displayed on the monitor when the next shot is fired Smartcard reader Insert smartcard or press any key to cancel Insert the smart card to mark off the shot fired or push a button to disrupt the shot will not be marked MpX 97 14 www kme no User Manual Monitor and SDU 5 4 6 2 Without access control 7 Insert smartcard or press any key Y Push a button or insert a User Card Even if User Card has been programmed for a limited number of shots it will not be counted down during the shooting All cards have unlimited access NB To get back to the Log On window after having logged on Menu 3 must be chosen and the Log off choice activated This applies even if a User card is used MpX 97 15 www kme no User Manual Monitor and SDU 5 4 Start up when certain targets are used When targets with integrated target electronic are used does not have external target electronics the system should be started normally until Insert smartcard Insert smartcard or press any key 7 Y
5. re mark the shots and choose what 10 shots to be displayed All other options changing series test shots etc are controlled by the control room software on the PC In Orion it is possible to set up the displaying of the shooters name when a new relay of shooters is loaded In addition it is set up in Orion what is to be displayed in the information field and if the position X Y are to be displayed on the average hit point Se Orion user manual for more information on this MpX 97 26 www kme no User Manual Monitor and SDU 8 SYSTEM SETUP To do some adjustments that the ordinary users shall not have access to there is a special setup on the monitor This setup menu is activated by inserting the Installation card that came with the system 8 1 Start up Start up all the monitors as usual so they have the log on picture on the display 97 Insert smartcard 47 Insert the Installation Card in one of the monitors and all the monitors will start up the setup program Setup Starting setup program MpX 97 27 www kme no User Manual Monitor and SDU Number of incomplete noise registrations in the target Number of transmission errors between the pit and the shooters stand Shot count Noise registration Count Red3 Reg1 2 S 1 220 0 225 1504 Remo Number of shots totally fired on this
6. target Number of shots fired on this target since the last zero out The setup menu will appear on the monitors after a few seconds It is only on the monitor with the installation card where all the menu options are valid On the other monitors it is only options that are special for each monitor that are valid Move marker up Move marker down Ok Select OK NB The number of shots and the noise registration get stored on the SDU Therefore it doesn t matter if monitors switch places or are switched between several shooters stands Be aware that the values will not be correct if the SDU is used on several shooters stands MpX 97 28 www kme no User Manual Monitor and SDU 8 2 Printer setup Before printing can be done the SDU s must be set up with correct printer driver An ordinary DOS PC printer can be connected to the SDU Windows based printers can not be used We recommend using either ink jet printer or laser printer Because of low printer speed and low print out quality we advise against using a dot matrix printer The printer set up has two choices Printer setup Monitor Back Ok Return Return to main menu Move marker up Move marker down Ok Continue 8 2 1 SDU Signal Distribution Unit 7 Printer driver Back Change Return Return to printer setup Move marker up Move marker down Change Change printer driver MpX 97 29 www kme no User Manua
7. 21 6 43 Saye Series cede tacos 22 6 5 MEN 23 6 5 EH MN 23 0 3 259 5 c eroe Ee mc E e DEAS 24 6 53 3 Target light epe ho mte Dp dete d ed ede tete 24 Off CL 24 Te CENTRAL CONTRO aeo 25 T PREPARATIONS ee ee eH ten tbt e ee EE 25 eee tatit tee E RR e IA dae eee EE ue OR NE 26 MpX 97 2 www kme no User Manual Monitor and SDU S SYSTEM SETUP roe ree va ccowosessvescstassosectvcuetcotesssestescaccsdessesessencesectecsssessosceseteecsenessecsevsebocespessesvesese 27 MEME MERE 8 2 PRINTER SETUP E 8 2 1 SDU Signal Distribution Unit aeternitate acaso S2c6hangessssak t actu M e MD uM t LEE 0 22 NC Monitor tende ice o edat Eee rp deca ete bit es 8 2 2 I Automatic s her oor eror e et or i t Ct ter Lavy b o E EN RE 8 2 2 2 SDU X Signal Distribution Unit 8 3 MONITOR SETUP rerit teet oret tor ve ee ive Feed ER Re e UY RE RERO beac UM UD 8 3 1 Access control h BPA Ee D RETI
8. card Installation Card New software on floppy disks must be available Carefully follow the directions below and carry out the instruction in the order it is listed Be aware that the installation Installation Card is to be inserted into the SDU and not the monitor There are two ways to perform the upgrade In system mode or from normal start up If for instance files are missing during normal start up so the monitor does not start correctly the system has to be started up in system mode to be upgraded Normal start up will be easier to carry out and is recommended if possible MpX 97 35 www kme no User Manual Monitor and SDU 9 1 System mode Turn off the power to the system and disconnect the monitors When everything is turned off put the Installation Card in the SDU Turn on the power supply every monitor has to be started up one by one When connected one of the menu buttons must be pushed in and held it doesn t matter which one it is but just make sure that it isn t any of the contrast buttons While this button is pushed in turn on the monitor The button must be held in until the image appears on the monitor display It will now say System Mode on the display Repeat this start up sequence on all the monitors 723497 When all the monitors says System Mode on the display it is set for the upgrade itself Insert the floppy disk in the SDU Extract and then insert the Installation Card
9. is done it will say Upgrade done on the monitors Make sure all the monitors have this message If one or more monitor displays an error message these will have to be upgraded again Remove the floppy disk and then the Installation Card from the SDU and the system will restart NB When the SDU is restarted with the Installation Card in the reader it will start up in System Mode If the monitors start up normally they will not obtain contact with the SDU Remove the Installation Card and try again MpX 97 37 www kme no
10. receive indicator 9 y Mode switch Connection point for PC Radio receive indicator lamp Only on radio version Connection point for power supply monitor MpX 97 6 www kme no User Manual Monitor and SDU 3 ERROR CODES To indicate errors or correct operation beeping sounds are used both on the Monitor and Signal Distribution Unit SDU Each signal consists of three tones at different tone levels An OK signal is three short tones in an ascending order An error signal is three short tones in a descending order High tone High tone 5 ike r EH Low tone Low tone OK BEEP ERROR BEEP In addition there is a beep signal for serious error that prevents the program from continuing It will beep a number of times equivalent of the error code that has arisen The beep signal will repeat itself after a short pause Count the number of beeps and contact the vendor for assistance 4 SMART CARD T1397 There are two types of smart cards User Card Jnstallation Card The shooting range receives one Installation Card This card is kept by the system administrator With this card advanced setups can be done something the ordinary user won t get access to Normally User Smart Cards are not delivered to the monitors These cards programmer and software are delivered when ordered separately See System setup for how to turn on and off access control with User Smart card
11. the shooter should log out to make the system ready for the next shooter Even if not every shooter uses a User Card it is recommended to log off to reset the monitor for the next shooter NB Even if the Smart Card is removed the monitor will not log off MpX 97 24 www kme no User Manual Monitor and SDU 7 CENTRAL CONTROL Shot no Co Shot value Shot direction compared to target centre ANOD ON Na LINAST AANA N Zoom t Zoom Optional info field Here shown with shooters name Re display Zoom target Display next series 10 shots If the control room software Orion is used the monitors are controlled from a central PC Shooters Stand Leader See Orion user manual for more information on this 7 1 Preparations When central control is to be used it is important that all the monitors get a normal start up See Normal start up All monitors shall display the log on picture 72497 Insert smartcard Y MpX 97 25 www kme no User Manual Monitor and SDU When all the monitors are displaying the log on picture Orion control room software can be started up After the System Check has been run on Orion the monitors will prepare for use Preparing monitor After up to 1 minute preparation the target image will be displayed on all the monitors 7 2 Use The only thing the shooter can do is to zoom the target
12. they will also be marked 1 and 2 If an existing system is to be expanded the whole system should be upgraded or there is a big probability that the old and the new units will not work together NB If there are two floppy disks it is important to start the upgrading with the disk marked 1 Follow the directions closely and be aware that the Installation Card should be inserted in the SDU and not in the monitor Turn off the power to the system and disconnect the monitors When everything is turned off put the Installation Card in the SDU Turn on the power supply Now every monitor has to be started up one by one When connected one of the menu buttons must be pushed in and held it doesn t matter which one it is but just make sure that it isn t any of the contrast buttons While this button is pushed in turn on the monitor The button must be held in until the image appears on the monitor display It will now say System Mode on the display Repeat this start up sequence on all the monitors When the monitors say System Mode on the display it is set for the upgrade itself MpX 97 9 www kme no User Manual Monitor and SDU Insert the floppy disk in the SDU Extract and then insert the Installation Card in the SDU The SDU will now start to read the floppy disk and a message will appear saying Upgrade in progress on the monitors The upgrade might take from 15 seconds
13. 0856 Flashdisk Free 333 Total 848 kB To avoid problems in the communication between the SDU and the monitor it is necessary to install a version that supports both units You might use floppy disks that came with the system for upgrade See Software upgrade for upgrading the system software NB If monitors are borrowed from other installations other shooting ranges it may not be the same software version on the two installations Then the installation with the oldest version must be upgraded before the systems can be interchangeable A version conflict must be checked out well in advance before a competition MpX 97 11 www kme no User Manual Monitor and SDU 5 4 3 Setting the Lane number After system check an option for setting the lane number will appear on the monitor Setup Target No Date 05 02 2004 Increase target no Decrease target no Move on The lane number can be set from 1 to 99 and must consist with the target number that is set up on the target electronics in the pit Physical placement of the monitor at the shooters stand has no importance for what lane number is set up The lane number will be stored in the monitor We recommend that each monitor has an assigned place so you don t have to set up the lane number every time the system is started NB Two or more monitors can not have the same target number except when one or more monitors are set up
14. 9 X 0 43 4 9 1 0 8 5 45 8 16 2 Print out example MpX 97 21 www kme no User Manual Monitor and SDU 6 4 3 Save series new menu will be displayed Cancel Last series Cancel Cancel saving and returns Last series Saves the series in the monitor memory To save the series on a floppy disk the shooter must bring a floppy disk and the User Card to the SDU On the SDU the user must first insert the floppy disk and then insert the User Card into the Smart Card reader When the card is inserted the series will be transferred from the monitor or monitors if the user has used more then one to the floppy disk After a while the SDU will give several beeps to inform that the transfer is finished and the floppy disk and the card can be removed Just one will inform that no series was found NB The series will only be saved in the monitor and then deleted when the monitor is turned off So the monitor must not be turned off until the series are saved on a floppy disk NB It will not be possible to save series when not logged on with Smart Card MpX 97 22 www kme no 6 5 Menu 3 User Manual Monitor and SDU Info H W Log off In Menu 3 there are several settings that can be changed Info Show shot and Target light What setting to change is selected with the second key on the display panel Come ww 6 5 1 Info X Y the line above the menu there is an in
15. At this point the system has to rest for approximately one and a half minute before further use i e SmartCard is inserted or Orion control room software is started The reason is that these targets use an extended communication protocol and this resting period is used to establish system architecture in the butt It is therefore also important that the butt is started before the stand This resting period is not necessary if the monitors proceed to the log on window without operating the keypad Monitors can later be re started and or attached without having the resting period as long as the system has been started correctly MpX 97 16 www kme no User Manual Monitor and SDU 6 TRAINING PRACTICE X 2 X 95 Shot value 9 8 Shot direction compared to 9 5 9 0 8 8 9 6 8 8 8 6 Target type Optional info field MENU 1 Displays menu shown 1 3 series Here shown with shooters name Menu choice for Menu 1 Left button is a menu selector that makes the other three switches changes function The system consists of three menus Menu 1 Menu 2 and Menu 3 If personal smart cards User Card are used a greeting will be displayed when the card has been inserted On this greeting it will also say how many shots are left in the card if it has been programmed for a limited number of shots If access control is not used this info will not be displayed
16. YS 497 Monitor SDU User Manual D Kongsberg 5 www kme no User Manual Monitor and SDU This user manual explains how to start up and use the Monitor and the Signal Distribution Unit SDU TABLE OF CONTENTS THE MONITOR qr 4 2 SIGNAL DISTRIBUTION UNIT SDU MODELS cssscsssssrcssssscesessscccsssseccsssssessscecesssscesssssssessess 5 PHE SD Wal MODEL 5 1 utere etn dei 5 2 2 THE SD U2 MODEL E E 6 S ERROR CODES sesesesestelaesse tesesssecoleessessesessasecs 6 JERROR CODES E E M 7 4 SMARE GAR D mc e E 7 Se START UP H 8 5 POWER SUPPLY e 8 MERERI ESSE EE E E 8 33 1 24PoWwer model 2 5 etes ei ain 8 9 2 HE MONITOR ees tnd Shas lee de ted Ba 9 35 3 FIRST TIME scabies teenies soared 9 S A NORMALE START UP EE reme e ta E FUP ql eret deems teta Pese teet te Eee dl 11 0 4 System CHECK 3 ust qae qe e RM 11 5 4 3 Setting the Lane 12 34 4 Choose Target ty Pe i e ee eadeni ei p ehe IHRER dle Re Sai 12 34 4 Choose Target type s e ep eet eg eed dest E TEA 13 2 43 Choose Ta
17. as slave See Monitor system setup NB Date and time is set up in the monitor system setup See Monitor System Setup MpX 97 12 www kme no User Manual Monitor and SDU 5 4 4 Choose Target type Each SDU contains a target menu that is unique for each system Any additional targets types can be ordered by contacting vendor Choose target INT 300m Move up on the list Move down on the list Choose Target type 5 4 5 Choose Target model If the system has two or more Target models with the same Target type a range of Target models will be displayed Choose target type Move up on the list Move down on the list Choose Target model NB Make sure that the correct Target model is chosen Even if the wrong Target model is chosen a hit point will be calculated but incorrect MpX 97 13 www kme no User Manual Monitor and SDU 5 4 6 Getting access to the system Each monitor can be set up for performing access control or not If access control is used each user will need their own smart card The access control only applies for training When control room software Orion is used the access control will not apply In this case regardless of access control or not all the monitors must be started up so they have this Log On image before the control room software is started See System Setup to activate or deactivate access control 5 4 6 1 With access control
18. d between several shooters stands the target centre point should not be set 8 3 4 Feeding Setting in mm how much paper strip rubber band to be fed for each shot fired on targets with automatic feeding MpX 97 33 www kme no User Manual Monitor and SDU 8 4 SDU setup SDU setup Date 05 02 2004 Time 13 58 Protocol A SDU Auto Protocol B SDU Auto Next Ok Next Move the marker to the next setting Increase next value Decrease previous value Ok Store SDU setup and return The SDU setup can be done from the monitor that the installation card was inserted into 8 4 1 Date time All monitors draw date and time from the SDU at start up This way all monitors doesn t have change the time setting for summer winter time 8 4 2 Protocol A and B SDU protocol and Auto shall be selected on both channels MpX 97 34 www kme no User Manual Monitor and SDU 8 5 Delete shot counters Setup menu Printer setup Monitor setup SDU setup Reset shot counters ot coun oise registration Count Tot Reg3 Regi f2 CS 225 1504 1 220 0 Remove smartcard to save System will restart Ok It is possible to delete shot counters and noise registrations except the total counter The counters can be used for maintenance purpose 9 SOFTWARE UPGRADE To upgrade the software on the monitor and the SDU a floppy disk station on the SDU is used together with an installation smart
19. ese are LOW MEDIUM and HIGH Usually MEDIUM is the best choice here If the printer is a dot matrix printer EPSONS EPSON24 or IBM X24 it might be better to use LOW because it will give a faster printing HIGH resolution should only be used with a very fast printer MpX 97 30 www kme no User Manual Monitor and SDU 8 2 2 The Monitor Choose a printer for this monitor SDU 1 Ok Move marker up Move marker down Change Change monitors setting 8 2 2 1 Automatic choice Normally this is the best choice The monitor then chooses a printer that is available 8 2 2 2 SDU X Signal Distribution Unit Sets the monitor to print out on an appointed SDU MpX 97 31 www kme no User Manual Monitor and SDU 8 3 Monitor setup Monitor setup Access control Slave Target zero point X Target zero point Y Feeding Next Ok Next Move marker to the next setting Increase next value Decrease previous value Ok Store monitor setup and return Each monitor has its own setup that can vary from monitor to monitor 8 3 1 Access control If access control is set up all users will need a Smart Card User Card to log on or a Smart Card has to be inserted in the monitor at all times Without access control it is possible to log on without a Smart Card only by pushing a key It will still be possible to log on with a Smart Card but if the card has been programmed for a limited number o
20. ew series If Target Lift is installed the Target will go to selected position 6 3 2 Zoom The number of zoom levels will vary from target to target Normal targets will have three zoom 6 3 3 Next 10 shots There is only room for 10 shots values in the list to the right on the display If there are more than 10 shots in the series this button can be used to select which 10 10 shots to show ex shots no 1 10 or shots no 11 20 NB The Hit markings will display all the shots that are fired Use the Mark series choice on Menu 2 to display only the shots that are displayed in the list MpX 97 20 www kme no User Manual Monitor and SDU 6 4 Menu 2 Print Save series sores sones 6 4 1 Mark series The series that is shot will be marked again with a small pause between each shot NB It is only the shots that are listed to the right that will be displayed To display other shots Next 10 shots on Menu 1 must be used to select the next shots 6 4 2 Print series A new menu will be displayed Last cance series Cancel Cancel printing and returns Last series Prints out the last series Ola Nordmann 73 8 65 2 1 1 07 02 1980 21 33 s 5 S S 5 9 5 B 1 8 90 9 8 X MID 2 o Y MID 37 9 o o TOT 86 o 8 o DFS 200m 1 9 8 599 24 6 84 121 3 45 2 2 8 9 1 6 104 7 7 8 8 51 3 3 9 8 29 55 2 8 8 2 12 1 14 4 9 8 V 25 2 53 4
21. f shots the number will not be counted down 8 3 2 Slave Normally two monitors should not be set to the same lane number By setting one monitor as a slave you can do this The slave monitor will receive the same shot information as the master monitor but it will not be possible to delete series activate marking of shots store and print out Deleting shots must be done from the master monitor New series and the same goes for activating the marking of shots MpX 97 32 www kme no User Manual Monitor and SDU 8 3 3 Target zero point It is possible to move the electronic centre point of the target with 1mm steps To do this centre adjustment the monitor must first be started up in training mode and the info field set to display X and Y on the last shot Put for instance a millimetre paper on the target where you mark on the paper where the centre of the aiming point should be Fire a shot and find the shots coordinate on the paper Y Target centre point X Y Also make a note of the shot s position X and Y values given on the monitor The Target Centre Point the correction factor that shall be inserted is calculated with these formulas Target centre point X Monitor X Paper X Target centre point Y Monitor Paper Y Please ensure that the correct sign is displayed for the X and Y coordinates NB The electronic centre point correction is stored in the monitor so that if the monitor is move
22. formation field where the user can choose what to display H W X Y C C Name MpX 97 Height and width dispersal The height dispersal is the distance between the two shots in the series that is the highest and lowest The width dispersal is the distance between the two shots furthest to the right and left Both i X and Y coordinate on the last shot mm Centre centre dispersal i e the distance between the two shots furthest apart from each other mm The shooters name is displayed programmed into the User Card 23 www kme no User Manual Monitor and SDU 6 5 2 Show shot Since the system can handle different calibres gauges target types and target models it is possible to choose between two different sizes on the graphical drawing of the shot Fixed The shot is drawn up so it is easy to see on all zoom settings The drawing of the shot can be both larger and smaller than the gauge This setting is recommended for targets at 100 meters and up Gauge The shot is drawn up with the same size as the gauge 6 5 3 Target light Tar light Rapid is On targets with red and green light a light sequence can be set up Off The light on the target is turned off Rapid Light on the target runs according to the rapid program 7 seconds red and 3 seconds green that is repeated 5 times The program starts when New series and OK is selected 6 5 4 Log off After having finished shooting
23. in the SDU The SDU will now start to read the floppy disk and a message will appear saying Upgrade in progress on the monitors The upgrade might take from 15 seconds to 30 minutes depending on how much needs to be upgraded When the upgrade is finished an Upgrade done message will be shown on the displays Make sure that all the displays have this message If one or more monitors show an error message these monitors will need to be upgraded again Remove the floppy disk and the smart card from the SDU and the system will restart If there are two floppy disks the same upgrade is carried out with floppy disk 2 NB When the SDU is started up with the Installation Card in the smart card reader it will start up in System Mode Same goes for the monitor when a button is pushed in during start up If only one unit is started up in System Mode the units will not communicate with each other 9 2 Normal start up Startup the program normally so it says Insert card on all the monitors T2397 Insert smartcard or press any key nsert the floppy disk in the SDU Insert the Installation Card in the SDU MpX 97 36 www kme no User Manual Monitor and SDU The SDU will now start to read the floppy disk and a message saying Upgrade in progress on the monitors The upgrade can take from 15 seconds to 30 minutes depending on how much is being upgraded When the upgrade
24. l Monitor and SDU 7 Driver HP PCL 8 2 1 1 Change Res Medium Printer No 1 Driver Res No Ok Driver Change driver Resolution Change resolution Printer No Change printer no normally set to 1 Ok Return and store Driver For the printer to function correctly the right driver must be chosen You can choose between 4 different drivers Windows based printers can not be used DRIVER DESCRIPTION EPSON 9 Is used by 90 of all dot matrix printers and some ink jet printers EPSON 24 Is used by most 24 pin dot matrix printers 1 24 Isused by some 24 pin dot matrix printers HP PCL Is used by 90 of all DOS laser printers and ink jet printers Even if the printer is not in the list above practically all DOS printers emulate one of these drivers Check the printer user manual what driver it emulates If it doesn t say anything about this the following drivers are the most common DOT MATRIX PRINTER Epson 9 INK JET PRINTER HP PCL some Canon ink jet printers uses Epson 9 LASER PRINTER HP PCL Even if the printer is a 24 pin printer a 9 pin driver can often be used This often gives a faster printing NB Some printers that utilize Epson 9 24 driver will not always function correctly because of to little buffer in the printer It is then recommended to change to a printer that uses the HP PCL language Resolution It is possible to use three different resolutions on the print out Th
25. orner as Xm and Ym Xm 63 4 MpX 97 18 www kme no User Manual Monitor and SDU 6 3 Menu 1 This is the Main menu where the most frequently used functions are 6 3 1 New series new menu will appear when New series are selected In the New Series menu several settings are possible Mark shots Sighting shots and Position Settings are changed with button no 3 on the display panel Marking Pu Single Each shot is marked consecutively Series The shots are marked after the series are shot When the first shot has been fired the menu will change to After all shots are fires one of the buttons is pushed to mark the series Sighting shots Yes The shots will not be summed up and a triangle will be displayed in the upper right corner that indicates test shots x No The shots will be summed up in the sum and total field The total value will increase for each counting series To null out the totals the monitor must be logged out Position stanaing User Manual Monitor and SDU Standing Target with Target Lift will go to the upper position standing Kneeling Target with Target Lift will go to the middle position kneeling Prone Target with Target Lift will go to the lower position prone NB If Target Lift is not used this option will not have any function Finally OK is pushed to delete shots and start a n
26. rget model iie leo 13 35 4 6 Getting access to the Systenisi e eee ee ee ESSERE e AE RED E E a exte ea 14 5 4 6 1 With access control eee tede te ease e an 14 546 2 Witho t access controls 15 5 4 START UP WHEN CERTAIN TARGETS ARE USED c cccssssssessssceeesseeecsssaececeneeecsesaececsesaeeecseeeesesaeeecnesaeseceeeeeensgs 16 6 TRAINING PRACTIGE Go ea een Uo caen vo eno cen Vn Qua qoo ne S avv aU ep ne Eo pea sos SV EUN TRUE en Uo Cae sissi 17 6 1 SHOIS VALUE AND HIT MARKING er Belted ro eek ead e eo HAE tee Atte Wek dae a recu d 17 6 1 SHOTS VALUE AND HIT MARKING eintreten e Here eee ete eee esie 18 6 2 AVERAGE AE cepere 18 0 3 LE 19 6 31 i d d lee et 19 O23 2 LOOM 20 OSB NCKE LOS NOUS ee tto ED here n te ae as m ia Da Ge ce IAS 20 6 4 MENU 25 ie A eee S 21 02215857 ARM TX 21 06 4 2 PrintSefies ace tet cete reale Ro cet doe eee ene e
27. to 30 minutes depending on how much needs to be upgraded When the upgrade is finished a Upgrade done message will be shown on the displays Make sure that all the displays have this message If one or more monitors show an error message these monitors will need to be upgraded again Remove the floppy disk and the smart card from the SDU and the system will restart If there are two floppy disks the same upgrade is carried out with floppy disk 2 NB When the SDU is started up with the Installation Card in the smart card reader it will start up in System Mode Same goes for the monitor when a button is pushed in during start up If only one unit is started up in System Mode the units will not communicate with each other MpX 97 10 www kme no User Manual Monitor and SDU 5 4 Normal start up 5 4 1 System check The first that happens after the monitor is turned on is a system check This check makes sure that the system units in the monitor are working and that the communication with the rest of the system is working System check Serial No Version MS 00856 SDU 65 Monitor 65 Flashdisk Free 333 Total 848 kB If there is different software version on the SDU and the monitor an error message will appear WRONG VERSION SDU and monitor have not equal software version Monitor M 65 S 65 SDU M 64 5 64 Software upgrade is necessary Press any key MS 0
Download Pdf Manuals
Related Search