Home
DS-2CE16D9T-AIRAZH (manual)
Contents
1. HIKVISION TURBO HD Motorized Vari focal IR Bullet Camera User Manual Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual applies to DS 2CE16D9T AIRAZH model motorized vari focal IR bullet camera This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual Privacy Notice Surveillance laws vary by jurisdiction Check all relevant laws in your jurisdiction before using this product for surveillance purposes to ensure that your use of this product conforms Please refer to the product specification for camera parameters and functions 0200001050626 Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residentia
2. ON 6 D WDR OFF 6 DEFAULT a 7 DEFOG OFF 7 RETURN RETURN 8 RETURN RETURN Figure 3 2 Exposure Figure 3 3 HSBLC 3 3 4 Backlight WDR Set the WDR status as ON or OFF Backlight Compensation BLC GAIN Set the gain of BLC as High Middle or Low AREA Press the up down left right button to define the BLC position and size Select RET or AGAIN to go back the BLC menu or re define the BLCarea Default Restore the BLC settings to the default HSBLC Select an HSBLC area Set the DISPLAY status as ON Press the up down left right button to define the area position and size Set the HSBLC LEVEL from 0 to 100 Select ALL DAY or Night for the HSBLC mode Set the BLACK MASK status as ON or OFF 3 3 5 White Balance WB MANUAL ATW Auto tracking White Balance AWC SET are selectable 3 3 6 Day amp Night Auto Trigger Color and B W are selectable for DAY and NIGHT switches You can enable IRF in trigger mode 3 3 7NR 2D NR You can set 2D NR status as ON or OFF 3D NR Set the Smart NR status as ON and adjust the 3D smart NR sensitivity ranges from 0 to 100 Set the 3D NR LEVEL ranges from 0 to 100 Set the START AGC level as the threshold to enable AGC and set the END AGC level as the threshold to disable AGC 2D amp 3D NR 3D NR 1 SMARTNR OFF 1 2DNR OFF 2 EVEL 80 2 3DNR ON 3 START AGC 10 3 RETURN RETURN 4 END AGC 10 5 RETURN RETURN Fig
3. arpness Adjust the sharpness from 0 to 15 Monitor Monitor CRT and Monitor LCD are selectable LSC Set the LSC status as ON or OFF 3 3 10 RESET Reset all the settings to the default 3 3 11 EXIT Press OK to exit the menu
4. he battery to your supplier or to a designated collection point For more information see www recyclethis info Industry Canada ICES 003 Compliance This device meets the CAN ICES 3 A NMB 3 A standards requirements 1 Introduction 1 1 Product Features This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology It features high resolution low image distortion and low noise etc which makes it suitable for surveillance system and image processing system HD1080p video output 0 1Lux F1 2 AGC ON O Lux with IR 5 50mm motorized VF lens auto focus Smart IR Mode OSD menu parameters are configurable Auto white balance auto gain control WDR Function High performance 2MP CMOS sensor and high resolution bring high quality image rE Device supports 12V DC and 24V AC power supply Heater function will only be enabled with 24V AC 1 2 Overview 1 2 1 Overview of Vari Focal IR Bullet Camera gt Vounting Base Sun Shield Motorized Vari Focal Lens Figure 1 1 Overview of Bullet Camera 2 Installation Before you start Please make sure that the device in the package isin good condition and all the assembly parts are included Make sure that all the related equipment is power off during the installation Check the specification of the products for the installation environment Check whether the power supply is matched w
5. ith your power output to avoid damage if the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself 2 1 Ceiling Mounting Steps 1 Drillthe screw holes andthe cable hole inthe ceiling according to the supplied drill template 2 Hammer the supplied plastic expansion bolt into the screw holes 1 Screw Hole for Bracket 2 Screw Hole for Mounting Base Figure 2 1 Drill Template 3 Route the cables to the cable hole and connect the corresponding cables 4 Fix the camera to the ceiling with the supplied PA4 screws Figure 2 2 Fix the Camera to the Ceiling 5 Rotate the cover of camera anticlockwise and the direction button auxiliary video interface and the DIP switch show 1 Direction Button 2 Auxiliary Video Output 3 DIP Switch Figure 2 3 Image Adjustment E fror A small monitor can be connected to the auxiliary video output to adjust the video DIP switch is used to enable disable WDR function By disabling WDR function video output can be realized by both CVBS output and HD video output By enabling WDR function video output cannot be realized by CVBS output 6 Adjust the surveillance angle 1 Loosen No 1 adjusting screw to adjust the pan position 0 360 2 Loosen No 2 adjusting screw to adjust the tilting position 0 90 3 Loosen No 3 adjusting screw to ad
6. just the rotation position 0 360 4 Tighten the adjusting screws 360 5 1 2 oN 90 3360 Figure 2 4 3 axis Adjustment 2 2 Wall Mounting Steps 1 Drill the screw holes and the cable hole inthe ceiling according to the supplied drill template 2 Hammer the supplied plastic expansion bolt into the screw holes Figure 2 5 Fix the Camera to the Wall 3 Route the cables to the cable hole and connect the corresponding cables 4 Fix the camera to the ceiling with the supplied PA4 screws 5 Adjust the surveillance angle as shown inthe figure 2 4 3 Menu Operation Menu VIDEO OUT SETUP LAUGUAGE SCENE LENS Exposure BACKLIGHT WB Davanicut NR speciat aousT RESET EXIT INDOOR Zorn J SHUTTER BLC ATW AUTO 2D NR cam SHARPNESS OUTDOOR PRESET AGC HSBLC AWC SET COLOR 3D NR MONITOR MOTION Ga cee C WDR gt Manuat C B W gt LENSINIT aricHess C OFF D RIGGER PRIV arum o woR Figure 3 1 Main Menu wore You can call the menu and adjust the camera parameters with the direction button or a coaxial camera controller purchase separately You can also call the menu with supported DVR 3 1 VIDEO OUT PAL or NTSCis selectable 3 2 LANGUAGE Chinese and English are selectable 3 3 SETUP 3 3 1 SCENE You can select indoor and outdoor scene modes acco
7. l area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted ay municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return t
8. rding to the working environments 3 3 2 LENS The camera is equipped with 5 50mm motorized vari focal lens Click Zoom and Zoom on the DVR PTZ to zoom in and zoom out The camera automatically focuses after zooming in out ZOOM SPEED Move the cursor left right to adjust the zoom speed PRESET You can set delete and call the preset 1 to 64 presets are configurable FOCUS MODE Manual Auto and Trigger modes are selectable In auto mode the camera focuses automatically and in manual mode you can click Zoom and Zoom to focus LENSINIT You can reset the lens AFLIMIT 20m 10m 6m 3m 1 5m 1m 30cm and 10cm are selectable as the Min focus distance limit ZOOM VIEW Enable the zoom view and the zoom ratio displays while lens zooming in out 3 3 3 EXPOSURE EXPOSURE Manual and IRIS PRI are selectable SHUTTER AUTO 1 25 1 75 1 100 1 120 1 3 5k 1 6k 1 10k 1 20k and 1 30 kare selectable AGC You can set the AGC value from Oto 15 SENS UP You can set the SENS UP to OFF or AUTO BRIGHTNESS You can set the brightness value from 1to 14 D WDR You can set the D WDR as ON or OFF DEFOG You can set the defog function as ON to enable the function Position size and the defog gradation are configurable EXPOSURE HSBLC 1 EXPOSURE IRIS PRI 2 SHUTTER AUTO 1 SELECT AREA 1 3 AGC OFF 2 DISPLAY ON ae Ai 3 LEVEL zas z 20 4 MODE ALL DAY 5 BRIGHTNESS 40 5 BLACK MASK
9. ure 3 4 NR Figure 3 5 3D NR 3 3 8 SPECIAL Camera Title Edit the camera title on this section D effect FREEZE Set the freeze function as ON or OFF MIRROR OFF MIRROR V FLIP and ROTATE are selectable for mirror D ZOOM Define the zoom ratio of certain area from 2 to 62 NEG IMAGE Set the NEG IMAGE as ON or OFF SPECIAL MOTION 1 CAM TITLE OFF 2 D DFFECT vel 1 SELECT AREA 1 3 MOTION OFF 2 DISPLAY ONe 4 PRIVACY OFF 3 SENSITIVITY 30 5 DEFECT a 4 MOTION VIEW ON 6 HEATCTRL a 5 DEFAULT a 7 RETURN RETURN 6 RETURN RETURN Figure 3 6 Special Figure 3 7 Motion Detection Motion Select a MOTION area Set the DISPLAY status as ON or OFF Press the up down left right button to define the position and size of the area Set the SENSITIVITY from 0 to 100 Set the MOTION VIEW status as ON or OFF Privacy Select a PRIVACY area Set the DISPLAY status as INV MOSAIC COLOR or OFF Press the up down left right button to define the position and size of the area Up to 8 areas are configurable Defect LIVE DPC and STATIC DPC are selectable in this section PRIVACY ADJUST 1 SELECT AREA 1 2 DISPLAY MOSAIC 4 1 SHARPNESS 15 3 COLOR 10 2 MONITOR LCD 4 TRANS 1 3 LSC OFF 5 DEFAULT a 4 RETURN RETURN 6 RETURN RETURN Figure 3 8 Privacy Mask Figure 3 9 Adjust HEAT CTRL AUTO ON and OFF are selectable in this section 3 3 9 ADJUST Sh
Download Pdf Manuals
Related Search
Related Contents
AMX NXD-430-WH Itinéraire Pédagogique Voile (gd) COMPACT REFRIGERATOR GB AKM 403/01 BUILT-IN GAS HOB 設置・初期設定ガイド Programma di prevenzione delle allergie indoor User`s Manual for BT656Pro SDI Mod. Kit Admiral AD-1 Clothes Dryer User Manual Samsung M1777N Užívateľská príručka EP Helikopter „Typhoon/Typhoon Pro“ RtF EP Helicopter „Typhoon Copyright © All rights reserved.
Failed to retrieve file