DK-2890 manual
Contents
1. a b c d e a 10 Programming Location for Output 1 b 4 Programming option for EM Card Common User Code c 004 One of the 1 000 User IDs for the User PIN Card from 000 999 d Read Card Put the Card close to the card reader e Confirm the card is read 2 beeps the Common User Code goes to this User ID automatically f A Common User Code for example 8 6 2 5 MUST be set at the Programming Location 03 first for this operation mode The code can be used for all the EM Cards in this operation mode REMARK If more User PINs and Cards are required for Output 1 repeat the procedures 3 4 5 or 6 above with other User IDs such as 005 006 007 999 etc Total 1 000 users are allowed See Programming Location 10 for the details 7 Close The Programming Mode 2 beeps The programming mode is closed The keypad is back to normal operation mode OPERATION 8 Open The Door with The EM CARD READ 2 beeps the door is open 9 Open The Door with The User PIN sJ aJ 2J ij 2 beeps the door is open 10 Open The Door with The EM CARD User PIN eJ aJ 2J aJ 2 beeps the door is open 11 Open The Door with The EM CARD Common User Code 8 tefr2 5 2 beeps the door is open REMARK In the next Section KEY IN AND STORE THE DESIRED VALUES describes all the features and functions of the system in detail Users can follow them to tailor the d2. CONNECTION HARNESS 1 GREY 7LUGHTBLUE Eg IN N O d TAMPER N C zn UNE t Le ds 8 BROWN GND HB Mc eg e DR 3 PURPLE QWHITE DATA YO Ri BELL AU CONTACT E NO 4 ORANGE N C 12V OUTPUT 11 GREEN _ COM gt ge av 1 GND 6 BLACK 12 BLUE NO THE WIRE HARNESS e 1 2 TAMPER N C Tamper Switch Normally Closed Contact A normally closed dry contact while the front cover is secured on the main box It is open while the cover is separated from the box Connect this N C terminal to the 24 hour protection zone of an alarm system if necessary e 3 4 DOOR BELL Output Relay Contact for Door Bell It is a Normally Open N 0 relay dry contact with maximum rating of 24VDC 1Amp It is prepared as a triggering contact of a low voltage door chime The contact point keeps close as long as the bell button on the keypad is pressed e 5 6 12V DC Power Input Terminal Connect to 12V DC power supply The supply and the GND are the common grounding points of the system e 7 EG IN Egress Input A Normally Open N 0 input terminal referring to ground With the help of connecting a normally opened button to activate Output 1 for door opening in the same manner of using the Group 1 User PINs or Cards Egress butto
3. The Visitor Codes will be cleared automatically after use if they are one time codes or when the allowed time expires LOCATION VISITOR ID VALID PERIOD VISITOR CODE VALIDATION fo clj sie r B VISITOR ID 50 Visitor IDs for storing the codes They are represented by a Two digit ID Number of o 1 to 5 o oJ eJ Jj Clear all the Visitor Codes from Location 40 Please see the Programming example below for the details VALID PERIOD The codes in this box MUST be two digits and they represent the time of the operation oJ o One Time Code One Time Code has no time limit but it can only be used for ONCE It is cleared by the system automatically after use oJ 9 9 Time Limit in Hour s The Visitor Code can be set with the valid time limit of 1 Hour to 99 Hours with a two digit number of 01 to 99 The visitor code is cleared by the system when the time limit reaches VISITOR CODES e When a new Visitor Code is put in the same Code box the old code is replaced e The Visitor Codes can be 4 8 digits for the Manual Mode code entry e The Visitor Codes MUST be in the same digit length with the Master Code for Auto Mode code entry NOTE All Visitor Codes will be cleared after power down to prevent extension confusion of their valid time limit EXAMPLES Example 1 Set a One Time Visitor Code with the number of 1 2 6 8 for the Output 1 Je cef Geeks j a b c d 6 a Visitor Code Pr
4. d 6 The Private User PIN is programmed for operating of the Output 1 The operation is Private User PIN only Take ID number 002 in Group 1 to store the Private User PIN which is one of the IDs in 000 999 m Put Private User PIN 1 2 3 4 into the storage location e Press to confirm and store the Private User PIN into memory two beep confirms a valid entry ii Operation while the system is back to operation mode Gers a a b a Key in the Private User PIN 1 2 3 4 b Confirm it with the key Output 1 activates 3 Example 3 EM Card Secondary User PIN i Programming oog gagag s a b c d e f a The card is programmed for operating of the Output 1 b The operation is EM Card Secondary User PIN c Take the ID number 003 in Group 1 to store the Card amp PIN which is one of the IDs in 000 999 d Put the card close to the reader One beep confirms the reading e Put Secondary User PIN 2 4 6 8 0 into the storage location f Press to store the Card Secondary User PIN into memory two beep confirms a valid entry ii Operation while the system is back to operation mode Read 2 4 6 a b c a Put the EM card close to the reader Two beep confirms the reading and 30 seconds waiting time is given for the entry of the User PIN the Amber LED keeps flashing b Key in the Secondary User PIN 2 4
5. 6 8 0 c Confirm it with the key Output 1 activates
6. Successful Key entry 1 beep the Output Operation Announcer 2 beeps or 1 long beep and the Unsuccessful User Code Card entry 5 beeps NOTE The beeps for the Warning and the Power up Delay do not belong to pacifier tones and can not be set to OFF 1 Pacifier Tone ON Default All the Pacifier Tones available from the keypad are enabled They are the response tones indicating the operation status of the keypad after the Card User Code is entered 0 Pacifier Tone OFF All the Pacifier Tones are OFF Good for place needs for a silent environment 21 CONFIGURATION OF THE OUTPUT MODES OF OUTPUT 1 Location 51 The relay output of this keypad is programmable for Start Stop or Timing modes Apart from the door access control alarm arm disarm control it is also an universal timer for automatic operator in industry with its 99 999 seconds over 24 hours programmable timer LOCATION OUTPUT MODE amp TIME VALIDATION sp Qg AA A OUTPUT LOCATION 5 1 Location for Output 1 OUTPUT MODE amp TIMING 0 J Start Stop Mode Toggle The number 0 sets the output to the Start Stop mode The output Starts when an User PIN and or Card is entered read the output Stops when an User PIN and or Card is entered read again 1 J 9 Seconds Momentary Default Momentary 5 Seconds The output can be set in Momentary Mode with the time of 1 second to 99 999 seconds The output will
7. authorization code for setting the system to programming mode It is NOT an User Code operating of the output relays e The Master Code can be 4 to 8 digits Press key to confirm code entry e When a new master code is keyed in and confirmed the old master code is replaced automatically e The master code is also the Link up Code between the keypad and the optional controller of the system in Split decoded operation e Example Set a Master Code with the number of 2 2 3 3 oJ 2J2J JJ RECORD SUPER USER PIN Location 02 The Super User PIN has TWO functions It is prepared for the owner to use it to operate the keypad under inhibit condition and make operation of inhibit enable disable to the system output LOCATION SUPER USER PIN VALIDATION oJi2 4 to 8 Digits SUPER USER PIN 2 e Super User PIN can be 4 to 8 digits e Two beeps will be heard after pressing the key to confirm code entry e When a new Super User PIN is keyed in and confirmed the old one is replaced e Example Set a Super User PIN with the number of 2 5 8 0 oJ 2J 2 5 JL to aj e To deleted a Super User PIN from memory Key in just the Location number and oj sj 14 VISITOR CODES FOR OUTPUT 1 ONLY Location 40 The Visitor Codes are the temporary user codes for operating of the Output 1 mainly for door strike in access control They can be programmed as Time Codes or Codes with Time Limit
8. department Also it will be easier to trace out the department of the lost card belongs to Of cause the owner can use a proprietary Secondary User PIN for each EM Card in the EM Card Secondary User PIN programming to further increase the security if it is the main concern f Security Level Comparison of The Secondary User PIN Code following Card Reading i EM Card Common User Code All EM Cards use the same User Code Security level is better than just Card only A lost Card picked up by any people can be used if he knows the Common User Code ii EM Card Department User Code The EM Cards are divided into groups with a Department User Code A lost Card can be used only by the people in the same group who know the Department Code iii EM Card Secondary User PIN Each EM Card has its own proprietary User PIN A lost Card can not be used by other people g Make A List Recording of The User Names VS User Codes Suggest the owner to make a list recording of the User Names corresponding to the Codes PINs Cards that are going to store in the Locations and the IDs before the programming It will be a useful tool for the owner to easily program them smoothly and also to trace them from this multi users system in the future Example Please see the following page Example Fo y RECORD A MASTER CODE Location 01 LOCATION MASTER CODE VALIDATION 4 to 8 Digits s MASTER CODE K e Master Code is the
9. is a weatherproof self contained mullion mount compact keypad It combines the functions of digital m m E T keypad and proximity EM card reader in one unit Operation Mode 2 Master Keypad Valid Codes ajaj amp Keypad Mode The DK 2890 has been designed to work independently as a stand alone keypad or works together with an optional APO amp Cards only K 3 Slave Keypad Valid Codes controller to form a high security split decoded keypad system amp Cards only The keypad comes with plenty of functions for owner s selection via programming Owners can take them freely to tailor the desired features for their system DK 2890 is an ideal keypad mainly for Door Strike or Alarm Arm disarm control It is also a programmable industrial timer with the timing of 1 second to over 24 hours for Automatic Operator systems SYSTEM CODES FUNCTION CODE ENTRY RESULTS The unit is designed for surface mounting on wall or door frame The two relay outputs are coming with N C and N O Contacts for Door strike and N O Contact for Door Bell Factory Set Master Code for User to set system in programming Mode at the fof of of of CJ CJ 0000 Lae A PERMANENT OR System Programming Mode SYSTEM CODE amp IT 15 CODE GJ J CHANGED IF A NEW MASTER FEATURES CODE IS PROGRAMMED e A Member of The Tri Tech Series Keypads Compatible with The APO Access Controller DA 2800 or DA 2801 REFRESH CODE Refresh the system a
10. the reader window to read it on each ID Number box then confirm it with key if itis a Card ONLY or Card Common User PIN entry The Common User PIN is NOT required to key in here It will go into its location automatically after the Card is read e Read the Card first then key in the Secondary User PIN on each ID Number box then confirm it with key if it is Card Secondary User PIN The Secondary User PINs can be duplicated or a proprietary User PIN but can not be a duplicate of a Prime Code Owner can use the same secondary User PIN for a group of Cards as a group Common User Code or called Department Code for a specific relay output e Cards Operation Media 1 3 amp 4 and Private User PINs Operation Media 2 MUST be unique A repeated EM card or Private User PIN will be rejected and one long beep will be generated by the system to notify the owner 16 EXAMPLES PROGRAMMING AND OPERATION 1 Example 1 EM Card Only i Programming ape CJ a b c d 6 The card is programmed for operating of the Output 1 The operation is EM Card only Take ID number 001 in Group 1 to store the card which is one of the IDs in 000 999 ii Operation while the system is back to operation mode a a Put the EM card close to the reader Two beep confirms the card is read and the Output 1 activates 2 Example 2 Private User PIN Only i Programming Gute 2 oJoj2J GJ2Js 2 J b c
11. 1 VISITOR ID 01 50 CODE 2 VALID PERIOD Visitor Codes 4 o CODE CODE2 CODES NIL CODE 3 VISITOR CODE 4 8 Digits OUTPUT MODE amp TIME 51 O P Mode for O P 1 1 99999 Seconds OP MODE amp TIME 5 Seconds Momentary LOCK OUT CODE 1 10 Trial Lock out 60 Sec eI D Personal Safety amp Lock out 5 10 5 10 Trial Lock Out 15 6 LOCKOUT CODE Lock out 60 Minutes 00 No Lock out Seconds ENTRY MODE ode 2 70 PIN Entry Mode 1 Auto Mode jo ENTRYMODE nuak Msie 2 Manual Mode ode 1 71 Pacifier Tone ON OFF zJ J FUNCTONMODE Pacifier Tone ON FUNCTION MODE net 0 0FF 7 Output Announcer T z e FUNCTION MODE cuc SON Standby LED Flashing z s FUNCTIONMODE 4j es z a CODE 1 FUNCTION MODE 1 Momentary No warning 2 Momentary with warning ode 1 4 Hold Contact No warning omentary Egress Delay Warning 5 Hold Contact with warning CODE 1 CODE2 4 No warning TIME 0 CODE 2 DELAY TIME No Delay 0 No Delay 1 99 Seconds 28 SPECIFICATIONS e Operating Voltage 12V DC Nominal 11 15V DC e Operating Current 60mA quiescent to 95mA two relays active e Operation Temperature 20 C to 70 C e Environmental Humidity 5 95 relative humidity non condensing e Working Environment amp Ingress Protection Indoor or Outdoor IP 55 Weatherproof e Number of Users 1 000 PINs and or Cards e Proximity C
12. They have the priority to be read and they MUST be unique and can not be repeated in the programming A Prime code also can NOT be duplicated for a Secondary code to work with the EM Card vice versa b The Prime Cards All the EM Cards used in this system are Prime Cards The cards MUST he unique and can not be repeated use The Card always has the priority to be read when working with an User PIN in EM Card Secondary PIN or EM Card Common User PIN c Warning for A Repeated Use of Prime Code or Card One long beep is given if a Code PIN is keyed in or a Card is read It means that a Prime Code or a Prime Card is repeated The Code PIN or Card was already in one of the PIN or Card Locations or IDs The programming is invalid Change a new Code PIN or Card and program it again d Secondary User PINs The Secondary User PINs are prepared to enhance security It is put after a Card in EM Card Secondary User PIN programming They can be a repeated code within the Secondary PINs but it is NOT allowed a duplicate of the Prime Codes The system will reject a duplicated Prime Code for Secondary User PIN or vice versa e Getting Advantages from The Secondary User PINs The repeated Secondary PINs can be used as a Group Common User Code or called Department User Code for a group of EM Cards which simplifies the programming of using large number of different User PINs EM Card with Department Code prevents a lost card used by people of other
13. WEATHERPROOF MULLION MOUNT ACCESS CONTROL READER KEYPAD cece WITH APO DATA I O PORT DK 2890 Programming amp Installation Manual FOR ELECTRIC LOCK AND SECURITY SYSTEM INSTALLATIONS VERSION 04 2011 SIRE AEI PROTECT ON SYSTEMS LIMITED C INS www apo hk com TABLE OF CONTENTS APPLICATION HINTS FOR THE AUXILIARY TERMINALS INTRODUCTION ie a Conte AEQUO 4 A TAMPER N C seo epen ene yp er INSTALLATION nanaqta upo putus UR ou ret tds 6 I i aa prote Precautions eroi teisei pairi EA i EE E Aa a NEA ENRERE TATE RE EEREN E aa GAE A EE AAE EE E S 6 TAMPER 24 HOUR N C zone of an alarm system if required E Pr 6 NC prer eton gt vex iniaa he etur esum 7 i The OnBoard LED Indicators cr vu i be E EAT 8 The Pacifier Tones amp The LED Signals M e nn 8 FEATURE PROGRAMMING amp OPERATION INSTRUCTIONS 2 0 0 n 9 DOOR BELL N O Set System in Programming Mode with The Master Code 9 Direct Access to Programming Mode with The DAP Code 8 080 e 9 LL The connection of the Door Bell is optional The door Refresh The System with The Refreshing Code 9999 m 10 CER eem bell contact on the keypad is prepared for triggering of The Default Values of The Keypad e e e meme ene 10 s DOOR CHIME an low power door chime only DO NOT
14. and Cards MUST be unique Repeated PINs will be rejected Secondary User PINs in the EM Card Secondary User PIN can be repeated See the Important Note Programming Criteria for Codes in page 13 for more information LOCATION MEDIA USER ID CARD amp ORUSERPIN VALIDATION ape Gs e ofoj e ejej 2 USER GROUP LOCATION 1 co Group 1 For User PINs Cards Controlling Output 1 1 000 Users are allowed in group 1 for O P 1 SELECTION OF OPERATION MEDIA Number 1 2 3 or 4 represents the Media to be used to operate the keypad Number 5 is the authorization code for deleting of an PIN and or Card from its User ID GJ EM Card only ia Private User PIN only 3 EM Card Secondary User PIN 4 EM Card 4 Common User PIN 5 Delete an User PIN amp or Card from the selected User ID number oJejreje Clear all the PINs amp Cards from the selected Location It takes few seconds to a minute to complete depending on the Location selected and the data stored Please see the programming example below for the details USER ID NUMBER e A 3 digit ID is an identified number for each User PIN and or Card Repeated ID number will be rejected by the system ID Number 99 9 for 1 000 User PINs Cards to operate Output 1 CARD amp OR USER PINS The User PINs can be 4 8 digits Key in the User PIN on each ID Number box then confirm it with key e Just simply put the EM card close to
15. and the power up beep stops The keypad turns itself into programming mode like using the Master Code and it is ready to accept the new programming data 5 If the Egress Button is not pressed and the DAP code is not keyed in within the power up period the system will set itself to normal operation mode To set it back to power up mode repeat procedures 1 4 EGRESS BUTTON DAP CODE VALIDATION ouaa GIG PRESS ONCE DAP CODE e The DAP code is fixed on 8 0 8 0 and it is valid only in the Power up Period after the Egress Button is pressed e Validate the DAP code with the e 2 beep confirms the system is in the Programming Mode and the Mains LED is constantly ON e See RECORD A MASTER CODE at Location 01 for the details of programming a new master code NOTE If the keypad is linking up with the DA 2800 or DA 2801 controller in the Split decoded operation it is necessary to put the controller s Link up Jumper to ON position to get the new Master Code for it As the Master Code is also the link up code of the two units Do Not Forget to put the Link up jumper back to OFF position after the programming 9 REFRESH THE SYSTEM WITH THE REFRESHING CODE 9 9 9 9 The system can be refreshed to clear all the old data stored and back to its ex factory default values IMPORTANT NOTE Make sure that you really want to clear ALL the 0LD data before entering of the Refreshing Code The keypad will be
16. any number of 1 to 99 into the box to enable the Egress Delay The number is the time in second which starts to count when the Egress Button is pressed Output 1 activates the door is released when the delay time reaches NOTE 1 Momentary Contact The Egress Delay starts to count when the egress button is momentarily pressed Output 1 activates automatically door is released when the delay time reaches 2 Holding Contact The user MUST hold the egress button in contact for the whole period of the Egress Delay time until Output 1 activates If the egress button is released before the end of the Egress Delay the timer will stop to count and reset 3 The Egress Delay does not affect the operation of the User PINs Cards for Output 1 The User PINs Cards always give INSTANT action EXAMPLES Example 1 Set Egress Button in Momentary contact 5 seconds with delay amp warning beep teo 2 5 j a b c d a Egress function programming b Momentary contact with warning c Delay time of 5 seconds to release door d Entry confirmation 24 FEATURE PROGRAMMING amp OPERATION INSTRUCTIONS SET SYSTEM INTO PROGRAMMING MODE WITH THE MASTER CODE IMPORTANT NOTE 1 DO NOT TURN OFF POWER while the keypad is in Programming Mode Otherwise it may cause data lost error to the programmed features in the memory 2 The keypad beeps after power up Wait 1 minute until the end of the power up delay then key in the Master Code
17. ard Standard EM Card or Keyfob 125Khz e Number of Visitor Codes 50 programmable for one time or with the time limit Timings for Code Entry and Card Reading 10 seconds waiting for next digit entry 30 seconds waiting for code entry after card reading e The Timer 1 99 999 Seconds Over 24 Hours possible Programmable Timer for 0 P 1 e Egress Button Programmable for Instant Delay with Warning and or Alarm Momentary or Holding Contact for the Exit Delay e Output Contact Ratings Output Relay 1 N C amp N O dry contacts 2A 24VDC Max Door Bell Relay dry contact 1A 24VDC Max Tamper Switch N C dry contact 50mA 24VDC Max Magnet Operated Reed Switch Dimensions 168 5 H X 46 5 W X 24 D mm Weight 160g net e Housing ABS Plastic Box Specifications are subject to change for modification without notice INSTALLATION Inner box Back Cover Main Box Front Cover PRECAUTIONS 1 Prevent Interference The EM Card reader is working at the frequency of 125Khz Installation precautions are necessary i Make sure the location for installation has no strong low frequency electro magnetic wave signals Especially in the range of 100 200Khz ii If there is more than one keypads with the same operation frequency installed closely in the same location make sure that they are at least 60cm 2ft apart from each other to prevention interference 2 Prevent Accidental Short Circuit In the previo
18. back with its default values like a new unit Re program of the desired values are necessary REFRESHING CODE VALIDATION Leej E REFRESHING CODE The Code 9 9 9 9 is for refreshing of the system Once it is keyed in and validated with all the values programmed previously will be cleared EXCEPT the Master Code e The refreshing takes around 2 5 minutes During the keypad is being refreshed the Status LED Amber flashes fast until the end THE DEFAULT VALUES OF THE KEYPAD PROGRAMMING Nil User Program Required Nil User Program Required Nil User Program Required 40 Visitor Codes Nil User Program Required 60 Personal Safety amp Lock out Code 1 10 False Code Card Lock out 60 Sec eae ay CoE 94 Operation Modes Code 0 Stand Alone Keypad NOTE The DAP Code 8 0 8 0 and the Refreshing Code 9 9 9 9 are fixed in the operating system program It can not be changed in any ways or be influenced by the system in default setting 10 INTELLIGENT EGRESS BUTTON AN UNIQUE FEATURE OF A CONTEMPORARY KEYPAD Most of the keypads for access control are just for controlling of Going In from outside It is not enough for today s access control systems In fact controlling of Going Out is also very important in many public passage areas They are not allowed to use locks or digital keypads for stopping of Going Out due to safety reasons Such as hospita
19. curity Reason Ceo 2 3 2 8 9 is Master Code for example here only 3289 is the new Master Code and the 0000 is erased 3 Record an EM Card to Operate The Output 1 for Door Open afe LJ ojJoj 1 READ CARD a b c d 10 Programming Location for Output 1 b 1 Programming option for only c 001 0ne of the 1 000 User IDs for the User PIN Card from 000 999 d Read Card Put the Card close to the card reader Confirm the card is read 2 beeps 4 Set an User PIN to Operate The Output 1 for Door Open Hg 2 2 2 1 j a b c d e a 10 Programming Location for Output 1 b 2 Programming option for User PIN only c 002 One of the 1 000 User IDs for the User PIN Card from 000 999 d 8321 The User PIN that is programmed for door open 8321 is an User PIN for example here only e Confirm the User PIN 2 beeps 5 Record an EM Card User PIN to Operate The Output 1 for Door Open ce s lols REROCHRD ea s a b c d f 10 Programming Location for Output 1 3 Programming option for EM Card User PIN The User PIN can be repeated use or proprietary a b c 003 0ne of the 1 000 User IDs for the User PIN Card from 000 999 d Read Card Put the Card close to the card reader e 6 Record an EM Card Commom User Code to Operate The Output 1 for Door Open Ge 4 ooaj c
20. eration mode 25 EGRESS DELAY AND WARNING Location 90 LOCATION FUNCTION MODES DELAY TIME VALIDATION Jo Oe ob Hork CONFIGURATIONS OF THE EGRESS WARNING AND ALARM Key in the number to enable 1 2 4 or 5 configurations described below Momentary Contact without Warning Default Press the Button once No warning or alarm is given during Egress Delay nd for silent area The people have to wait for the door open until the delay time reaches 2 Momentary Contact Mode with Warning Beep Press the Button once The system gives Warning Beeps during the Egress Delay Good for the place required attention The keypad beeps during the people are waiting for the door open 4 Holding Contact Mode without Warning Press and hold the Button No warning or alarm is given during the Egress Delay Good for the silent area The people require to press amp hold the button until the delay time reaches for the door open 5 Holding Contact Mode with Warning Beep Press and hold the Button The system gives Warning Beeps during Egress Delay Good for the place required attention The keypad beeps while the button is kept pressed during the people are waiting for the door open EGRESS DELAY TIMER 0 No Delay Default Output 1 activates instantly the door is released instantly when the Egress Button is pressed Gj F 9J o Egress Delay Timing Put
21. esired values for their access control systems Suggest the general users also spend some time on them to get acquaint with this powerful system for future expansion 12 USER PIN ENTRY MODE Auto or Manual Location 70 LOCATION ENTRY MODES VALIDATION Zo ajo c USERPINENTEYMODES 1 Two modes 1 and 2 are available for User PIN entry options The EM Card is always in Auto Entry Mode and is not affected by the selection here 1 Auto Entry Mode Auto Entry Mode requires no pressing of the El key following the User PIN for code checking In the Auto Entry Mode the User PINs MUST be set in the same digit length of the Master Code For example if the Master Code is 5 digits then all User PINs must be in 5 digits as well All other User PINs not in 5 digits become invalid When the number of digits reaches the system will check the User PIN automatically Good for high traffic access control 2 Manual Entry Default Manual Entry Mode always requires the s key following of the User PIN for code checking The User PINs can be 4 8 digits arbitrary and they are NOT required to be in the same digit length of the Master Code Manual Entry increases the level of security in the code trial by the unauthorized people PACIFIER TONES ON OFF SELECTION Location 71 LOCATION FUNCTION MODES VALIDATION zd Gog W PACIFIER TONES ON OFF MODES The Pacifier Tone is the Beep Tones from the keypad which include the tones of
22. for setting the system into programming mode 3 For the owner s convenience in programming at the first time the factory has put a Master Code 0 0 0 0 into the keypad It is NOT a default code To compromise security in all cases the owner should program a new Personal Master Code to invalidate the factory set Master Code after the keypad is owned MASTER CODE VALIDATION Lococo GIG MASTER CODE e The Master Code can be a factory set master code or the private master code that was set by the owner e Validate the master code with 2 beep confirms a valid master code The Mains LED Amber is constantly ON after the system is set in the programming mode DIRECT ACCESS TO PROGRAMMING MODE WITH THE DAP CODE 8080 Set System Into Programming Mode With DAP Code In Case Of The Master Code Is Forgotten The owner requires to apply the following procedures precisely to set the system into programming mode with the DAP E 80 I N d j d di E 1 Switch OFF all the power for 1 minute to ensure that the system is fully discharged 2 Swich ON power again The system is in Power up Mode for 1 minute and the buzzer gives beeps during the whole period This is the only time limit for setting the system to Direct Access to Programming DAP 3 Press the Egress Button EG IN once first to enable the DAP function 4 Key in the DAP Code 8 0 8 0 and validate it with the existing Master Code in the memory is erased
23. ing and 30 seconds waiting time is given for the entry of the Common User PIN the Amber LED keeps flashing b Key in the Common User PIN 1 3 5 7 the number programmed in Location 0 3 for Output 1 in the previous Example c Confirm it with the key Output 1 activates 5 Example 5 Delete an User PIN amp or EM i Delete An User PIN or A Lost EM Card Jg 5 ET a b c d a Key in the User Group that the User ID belongs to 10 for the Group 1 This keypad has user Group 1 only b Key in 5 that is the Command Code for making a deletion here C Key in the User ID that stored the User PIN the lost EM card or the EM Card User PIN d Press the key Two beep confirms a valid entry and the PIN and or Card in that User ID is cleared ii Delete an EM Card je 5 Read Card J a b c d a Key in the User Group that the EM Card belongs to 1 0 for the Group 1 This keypad has user Group 1 only b Key in 5 that is the Command Code for making a deletion here c Put the EM card close to the reader One beep confirms the reading Read the Card only also makes a valid deletion to the Card working with the Common User PIN or the Secondary User PIN d Press the key Two beep confirms a valid entry The EM Card in that User ID is cleared Key in the User ID is not required 6 Example 6 Clear The Whole Group of Users Whole group of users including the PINs and Cards can be cleared with the fo
24. ler is required REMARK DA 2801 is the simplified version of the DA 2800 without wireless remote control funtion 27 THE OPERATION MODES Location 94 Four operation modes are available for the selection The codes are 0 1 2 and 3 LOCATION OPERATION MODE VALIDATION sys Jag H WIEGAND OUTPUT AT KEYPAD OPERATION MODE 0 Stand Alone Keypad Mode Default The system provides full functions to operate its outputs 1 Card amp Code Reader Mode Not Available in this model 2 Master Keypad of Split Decoded Mode The Master keypad will transfer all the programmed feature data except the user PINs Codes and Cards data to the Access Controller decoder right after it exits the programming mode A Split decoded keypad system needs at least one Master keypad and one Access Controller to work 3 Slave Keypad of Split Decoded Mode No feature data is transferred to the Access Controller decoder from the Slave keypad It takes the same feature data from the Master keypad to operate The Slave keypad s is for a Split Decoded system that needs more than one keypads for operation convenience NOTE a Do not set more than one keypads in Master mode in a Split Decoded system Otherwise the data will be confused b Each keypad in Split Decoded mode can be programmed independently with its own user PINs Codes and Cards The PINs Codes and Cards can be repeatedly used in other keypads in the same system 26
25. lit decoded mode that combines an outside unit for card reading and code entry and a control panel or a decoder unit installing in a secure closet inside the house The outside unit and the inside unit communicate in digital data with each other All the commands are in digital codes the thief can do nothing to the inside unit even the outside unit is opened in sabotage This design philosophy confirms high security to the area protected but not just relying on the protection of the keypad with the outer box and two screws The keypad unit comes with a data 1 0 data input and output port for the connection with the APO s Access Controller DA 2800 for Split decoded operation to up grade its security level Once the keypad unit is connected with the controller all the commands from it will be faithfully decoded by the decoder The input amp output control functions available from the keypad are now all transferred to the controller The keypad s role is just a card reader and or a keyboard for code entry The link up of the two units is very simple It is just one wire The White Wire for the 1 0 ports and a common grounding wire The Black Wire for the two units The 1 0 port provides the data in the proprietary APO format It ONLY works with the DA 2800 The Optional DA 2800 Controller Introduction The DA 2800 controller unit is compatible with the keypad unit Maximum 3 keypads can be connected in parallel to it It decodes the data faithfull
26. llowing command HA cefejsjs j a b c a The User Group 1 10 is selected to be cleared This keypad has user Group 1 only b Key in the Group Deletion Command 0 9 9 9 c Confirm the deletion with Z All the User PINs and Cards in the Group 1 are cleared It takes few seconds to a minute to complete depending on the data stored 18 OPERATION AND FUNCTIONS OF THE SUPER USER PIN 1 Operate Output 1 Output Relay 1 The operation of the Super User PIN is just like a normal User PIN Simply key in the PIN with a specific output number for the Output The Super User PIN can also be used to reset an operating output timer instantly SUPERUSERPIN 1 Output 1 Activates or Resets 2 Inhibit The User PINs For Output 1 The Super User PIN can also be used to inhibit the normal User PINs Cards for the Output 1 usually they are for door strike It enhances the security level of the access control system such as to stop a keypad after office hour or while the house is nobody inside Once the Output 1 is inhibited the User PINs Cards for it become invalid and those people even know the User PINs are refused during the system is inhibited The inhibit function is toggled in Start Stop mode with the following code entry SUPER USER PIN El The Whole Group of User PINs amp Cards for Output 1 are Disabled or Enabled in Toggle NOTE The inhibit function setting with the Super User PIN applies to the
27. ls kindergartens elderly homes convenient stores emergency exits etc The wardens teachers shopkeepers and the guards are always required to keep an eye on people to prevent unattended leaving shoplifting and illegal use of the emergency exits The Intelligent Egress Button can be programmed to do something to get the attention of the person on duty before the door is opened The button offers programmable egress delay delay with warning holding button required for the delay momentary button contact with warning for the delay Location 90 is the place for setting the desired functions for the Egress Button The functions programmed to the Egress Button do not affect the normal operation of the system with its keypad For the safety consideration the operation of the keypad with PIN Code or Card is always in the first priority to give instant action to the output relay 1 for door strike It is NOT required to program the Egress Button with the special function in normal use Just leave it on its default values WHERE AND WHY GOING OUT NEEDS ATTENTION Examples for some areas may need an Intelligent Egress Button Hospital Some of the patients are not allowed to leave the ward without doctor s permission An egress button with exit delay and warning beeps will help the nurse or warden to get the attention to the door when the egress button is pressed Further setting of the egress button with holding contact for the delay eve
28. n gives higher level of security to a controlled door Kindergarten Young children are always active Some of them may be willing to go out to explore their ways of playing For safety reason teachers have to watch all of them in the attended area Leaving school alone without the companion of parents or teacher is dangerous to the young children An egress button with delay and warning beeps will be helpful to prevent the children trying to go out without getting the attention of the teacher Elderly Home Elderly needs constant attention and care Some old people have poor memory They may forget the way to come back if they leave home alone An egress button with delay and warning beep will easily get the attention of the warden before the door is open Convenient Store Most of the convenient stores have just only one or two shopkeepers on duty They are usually the cashier Shoplifting may easily happen while the shopkeeper is busily serving customers at the cashier desk A holding contact egress button with delay and warning beeps may help to stop most of the shoplifting As the thief knows that he is gotten attention by the shopkeeper before the door is open High Traffic Passage A short buffer time may be necessary for opening a door outward after pressing the egress button for those exits open to a high traffic passage An egress button with short delay and warning beeps helps the user to pay attention to the people passing by to pre
29. n is usually put inside the house near the door More than one egress buttons can be connected in parallel to this terminal Leave this terminal open if not used See Programming Location 90 for more information about the Egress Button with other features e 8 GND Common Ground A common grounding point of the keypad e 9 DATA 1 0 Data Input Output Port for Split Decoded Operation A data bus for signal communication with the optional Access Controller in Split decoded operation See THE APO 1 0 PORT Section for the details e 10 11 12 OUTPUT 1 Output Relay 1 2 Amp relay dry contact controlled by the Group 1 user PINs or Cards for Output 1 recommended for door strike Terminal 10 is Normally Closed N C terminal 12 is Normally Open N O and terminal 11 is the common point of the two contacts Use N C output for Fail safe locking device and N O output for Fail secure locking device The relay is programmable for Start Stop toggle mode or Momentary timing mode See programming Location 51 for the details THE ON BOARD LED INDICATORS e MAINS AMBER It flashes on Standby It shows the system status in synchronization with the beep tones The standby flashing can be set to OFF in programming See Location 73 for the details e DOOR GREEN It lights up for Output 1 activation e INHIBIT RED It lights up while the output is inhibited THE PACIFIER TONES amp THE LED SIGNALS The buzzer a
30. nd set all its All programmed data are cleared and e Durable Epoxy Coated Back lit Key Board with Door Bell Button 9999 back to the default values except the function back to default Master Cod e Mullion Surface Mount Plastic Housing values oge e Operated PINs amp EM Cards DAP CODE Direct access e Self contained Stand Alone Operation 8080 D e 7 System in Programming Mode e Built in Data 1 0 Port Expandable for Split decoded Operation Bi p p y e Relay Output Contacts for Door Strike and Door Bell USER PINs Codes Cards whole group clearance Code Key in the Code to clear all the users in the Location LOCATION NO oj oJ oj J aj MU Ne un i the selected LOCATIONS THE OPTIONAL CONTROLLERS FOR SPLIT DECODED OPERATION DA 2800 Full Feature Decoder RF Remote Control EsitProgramimi a Code uS to normal opration DA 2801 Full Feature Decoder PROGRAMMING SUMMARY CHART ENTRY LIMITS amp CODE LOCATION FUNCTION OPTIONS CODE ENTRY FACTORY DEFAULT Super User PIN 4 8 Digits o 2 SUPERUSERPN NIL Common User PIN for O P 1 4 8 Digits COMMONUSERPIN1 NL CODE 1 MEDIA 1 Card 2 Private User PIN 3 EM Card Sec User PIN 4 EM Card Com User PIN 10 User PINs Cards for O P 1 5 Deletion of User PIN CODE 2 CODES NIL CODE 2 USER ID 000 999 Group 1 CODE 3 USER PINs Cards 4 8 Digits Cards CODE
31. nd the amber LED indicator give following tones and signals respectively for system status ON STATUS TONES On Programming Mode 2 Successful Key Entry 82 o 3 Successful Code Card Entry 4 Unsuccessful Code Card Entry Power Up Delay adi BH G 6 Output Relay Activation 1 Second Long Beep 7 On Standby 1 Flashin 1 Second Interval Fast Flashes for 2 5 Minutes 8 System Refreshing 9 Card or PIN Already Stored in System 1 Long Beep NOTE id All Pacifier Tones can be ON or OFF through the programming option at Location 71 TT The Output Relay Activation beep can be selected through the programming option at Location 72 Ee The Standby flashing can be ON or OFF through the programming option at Location 73 Example 2 Set Egress Button in Holding contact of 10 seconds with warning beep slo 5 A a b c d a Egress function programming b Holding contact mode with warning c Holding time of 10 seconds to release door d Entry confirmation Example 3 Set Egress Button in Momentary contact without delay This is the default setting go CO 0 j a b c d a Egress function programming b Momentary contact without delay c Release door instantly d Entry confirmation CLOSE THE PROGRAMMING MODE Always close programming mode with to set system back to normal Operation after programming VALIDATION ag MM System is back to normal op
32. ogramming b The Visitor ID c An One Time Code d The Visitor Code e Entry Confirmation Example 2 Set a Visitor Code with the number of 1 3 7 8 that is valid for three hours for the Output 1 4 coe toys A ce a b c d e a Visitor Code Programming b The Visitor ID c Valid for 3 Hours d The Visitor Code e Entry Confirmation Example 3 Delete a Visitor Code from Vistor ID oJ J in the memory Jo 092 J a b c a Visitor Code Programming b The Visitor ID c Delete Confirmation Example 4 Clear all Visitor Codes from Location 4 J Je cofefejfo a b c a Visitor Code Location b The Deletion Command Code c Confirmation all Visitor Codes are cleared 19 4 Example 4 EM Card Common User PIN i Programming cfe celer a b d e a The card is programmed for operating of the Output 1 b The operation is EM Card Common User PIN c Take ID number 004 in Group 1 to store the card which is one of the IDs in 000 999 d Put the card close to the reader One beep confirms the reading No need to key in a Common User PIN but there MUST be a Common User PIN already recorded in Location 03 e Press to store the Card into memory Two beep confirms a valid entry ii Operation while the system is back to operation mode Read Common User PIN s a b c a Put the EM card close to the reader One beep confirms the read
33. pad Operation Mode e 26 THE APO DATA 1 0 PORT FOR SETTING UP A SPLIT DECODED KEYPAD 27 The Optional DA 2800 Controller Introduction e cece eee teeter 27 2 31 APPLICATION EXAMPLE BASIC WIRINGS OF A STAND ALONE DOOR LOCK TAMPER N C DOOR BELL CONTACT N 0 12V DG n GND 12V DC POWER SUPPLY AD 1312 NOTE 7 LIGHT BLUE EG IN NO 8 BROWN GND 3 PURPLE 9 WHITE DATA 1 0 4 ORANGE OUTPUT 11 GREEN KECA 6 BLACK 12 BLUE THE WIRE HARNESS OUTPUT RELAY N O Output for Fail secure Lock N C Output for Fail safe Lock ELECTRIC LOCK EGRESS BUTTON a N 0 1N4004 CATHODE MORE EGRESS BUTTONS CAN g BE CONNECTED Wi N O IN PARALLEL e Connect the 1N4004 as close as possible to the lock in parallel with the lock power terminals of the lock to absorb the back EMF to prevent it from damaging the keypad The 1N4004 is not required if the electric lock is AC operated e To avoid Electro Static Discharge from interfering with the operation of the keypad always ground the terminal of the keypad to earth 30 PROGRAMMING SUMMARY CHART APPLICATION EXAMPLE Basic Wirings of A Stand Alone Door Lock APPLICATION HINTS FOR THE AUXILIARY TERMINALS INTRODUCTION OPERATION MODES 0 Stand Alone Keypad Valid The DK 2890
34. people find the flashing light of the status LED the amber LED is annoying during the keypad is on standby especially at the night time The standby flashing can be ON OFF with the setting here 1 Standby Flashing ON Default The Status LED gives Standby Flashing all the time during the keypad is on standby It also gives all the light indications showing the operation status of the system 0 Standby Flashing OFF The Standby Flashing is disabled but it does not affect the system status indications All the light indications from it are unchanged 22 KEYPAD PROGRAMMING MAKE SIMPLE For General Users The DK 2890 has many functions for user s selection For those general users taking the keypad for door strike only most of the features can be kept in their Default values Only the User PINs Cards and a private Master Code are necessary to program for the system The keypad accepts 1 Card only 2 PIN only 3 Card PIN or 4 Card Common User Code to operate its outputs PROGRAMMING NOTE Wait 1 minute until the end of the power up delay 1 Set System into Programming Mode with The Factory Set Master Code 0 0 0 0 2 beeps system is in Programming Mode Note If the Master Code is forgotten use the DAP Code to set the system into programming mode See DAP CODE 8080 on the previous page for the details 2 Change The Factory Set Master Code to Owner s Private Master Code for Se
35. reset automatically when the time expires OR it can be RESET manually at anytime with the Super User Code before the end of the time Example Reset Output 1 SUPER USER CODE s a Output 1 resets PERSONAL SAFETY AND SYSTEM LOCK OUT Location 60 LOCATION LOCK OUT MODES VALIDATION sjo ezm zl SAFETY amp LOCK OUT OPTIONS a The Options are represented by their Mode Numbers in programming They are described below a After 10 successive false Card User Code trials the keypad locks during 60 seconds Default 5 1 0 Selection of after 5 to 10 successive Card User Code trials the keypad locks during 15 minutes The keypad can be reset to release the lock out with the Super User Code in the following way Example Release the lock out SUPER USER CODE s 0 Disappearance of all the above lock out securities 20 FEATURE PROGRAMMING KEY IN AND STORE THE DESIRED VALUES The feature values can be set and stored into the system one by one with the desired Programming Locations Programming can be made continuously and it is not necessary to be in sequence order Just go to the desired programming location and key in the value for the desired feature IMPORTANT NOTE Programming Criteria for Codes a The Prime Codes All the Private User PINs Master Code Duress Codes Super User PIN Common User Code and the Visitor User Codes belong to Prime Codes in the system
36. us experience most of the damages caused in the installation are accidental touching of the components on circuit board with the wires carrying power Please be patient to study the manual to become familiar with the specifications of the system before starting the installations i Do not apply power to the system while it is in installation ii Check carefully all the wirings are correct before applying power to the system for testing PACKAGE CONTENTS One DK 2890 Keypad Two EM cards or keyfobs One pack of Mounting Screws One Programming amp Installation Manual One Connection Harness THE APO DATA I O PORT FOR SETTING UP A SPLIT DECODED KEYPAD The information here is for setting up the keypad unit with an optional Digital Keypad Access Controller DA 2800 to make up a high security Split decoded Keypad system only It is NOT required for the keypad in Stand Alone operation Split decoded Keypad System ost of the general purpose keypads on the market are self contained systems for stand alone operation It controls the appliance s directly with its output relay contact s such as the electric lock in an access control system The electric lock is connected to the keypad that is Installed outside the house The thief can open the door without a code or card but just open the keypad box and make contact to the output relay terminal It is a safety drawback in security The high security systems are usually operating in the Sp
37. use itas a high voltage power path for a door bell The maximum power KEYPAD PROGRAMMING MAKE SIMPLE For General Users e n RA 1 rating of the contact is 24V DC 1 Amp FEATURE PROGRAMMING KEY IN AND STORE THE DESIRED VALUES gt 13 Programming Criteria for Codes e M enne 13 Record A Master Code 202 x mener tette eee eere aee emet rts 14 Record A Super User PIN eese BER ER S MNT me 14 Operation And Functions of The Super User PIN sse 15 Record The Common User PINs for Output 1 e mn nnn 15 Record Delete PINs or Cards for Output 1 e 16 Examples Programming And Operation e n 17 Visitor Codes For Output 1 Only 9 n n 19 Configuration of The Output Modes for Output 1 e 20 Personal Safety And System Lock Out e nnn nnn 20 User PIN Entry Mode ic Pe ne ER Aet feed 21 Pacifier Tones Oris Off Selection za a a paka cas 21 Output Operation Announcer nns 22 Status LED Flashing On Off during Standby ee 22 Intelligent Egress Button An Unique Feature of A Contemporary Keypad 8 23 Where And Why Going Out Needs Attention e e terete nes 23 Egress Delay and Warning ss e e m e e I e e e ene ne nennen 24 Configurations of The Egress Warning And Alarm sse 24 Close The Programming Mode e H enne nee 25 The Operation Modes e HH enne nee 26 Wiegand Output at Key
38. vent hitting them when the door is pushed outward Emergency Exit Emergency Exit is not open to the public for daily use It is for emergency case only It is usually closed and watched by the security guards The egress button of this keypad can be programmed to offer exit delay with warning beeps when the door is forced to open or the door is open after the exit delay expired It is an useful tool to get the attention of the person on duty 23 OUTPUT OPERATION ANNOUNCER Location 72 LOCATION FUNCTION MODES VALIDATION aa Gog W OUTPUT OPERATION ANNOUNCER LO The announcer gives notification beep to the users and the visitors on the operation status of the outputs There are two notification modes available for the selection The notification is also OFF while the Pacifier Tone OFF mode in the Location 71 is selected 1 Second Long Notification Default 1 second notification beep is given when the output relay is activated with a valid Card Code or Egress Button It is prepared to notify the person outside the door when the lock is released and the door can be opened It is good for the door lock device gives no sound when it activates such as a magnetic lock 0 2 Short Beeps Notification 2 short beeps notification is given when the output is activated with a valid Card Code STATUS LED FLASHING ON OFF DURING STANDBY Location 73 LOCATION FUNCTION MODES VALIDATION i ci aoro E STANDBY FLASHING ono Tf Some
39. whole group of User PINs and Cards for Output 1 For safety reason the inhibit function initiated with the Super User PIN does not govern the Egress Button The door still can be opened with it from inside e The function of the Super User PIN is not affected in the Inhibited Mode or Lock out Mode It is always a normal user code for Output 1 RECORD THE COMMON USER PINS FOR OUTPUT 1 Location 03 The Common User PIN is prepared for operating of the Output 1 as an enhance code The Common User PINs MUST work in the form of Card Common PIN to operate the outputs to increase the security of the access control system See Location 10 for more information NOTE Common User PIN alone can NOT be used to operate Output 1 directly LOCATION COMMON USER PIN VALIDATION offs 4 to 8 Digits amp COMMON USER PIN LOCATION oJ J Location Stores The Common User PIN for Output 1 COMMON USER PINS e The Common User PIN can be 4 to 8 digits Press key to confirm the code entry e When a new Common User PIN is keyed in and confirmed the old one is replaced e Example Set a Common User PIN with the number of 1 3 5 7 for Output 1 ojs 1 5 7 e To deleted Common User PIN from memory Key in just the Location number and o s RECORD DELETE PINS OR CARDS FOR OUTPUT 1 Location 10 Total of 1 000 User PINs and or Cards are available for controlling of the output relay 1 The Private User PINs
40. y from the keypads even each of them have different settings of their own The only criterion nr Prisci ior link up is all the keypads are set with the same Master Code and is read by the controller while it is in the link up mode Apart from the decoding function to follow the features from the keypad s the DA 2800 is also an independent 4 channel RF remote controller to operate its 3 output relays and the built in door chime The DA 2800 is an ideal device working independently in the RF remote control areas such as door lock strike in access control garage door opening control alarm arm disarming control and automatic operator control etc The keypad unit is up graded to a Tri Tech system after in connection with the DA 2800 controller The system accepts EM Cards User PINs and the RF Remote Keys in access control RF WIRELESS REMOTE CONTROL 7 DOOR LOCK COMMON GROUND e gt GARAGE pu DOORORENER DA 2800 ACCESS CONTROLLER SS SECURITY SYSTEM DK 2890 OR AUTOMATIC DATA 1 0 DA 2800 OR DA 2801 OPERATOR CONTROLLER COMMON GROUND MAXIMUM 3 KEYPADS CAN BE DK 2890 CONNECTED IN PARALLEL DK 2890 IN SPLIT DECODED OPERATION The User Manual of the DA 2800 provides the operation details of the system on decoding controller mode and independent operation mode Please contact your local agent if purchase of the DA 2800 Control
Download Pdf Manuals
Related Search