IBZ-1041W 10.4`` Wireless Touch Panel
Contents
1. 19 20 2 2 The Cradle The cradle lets you dock your IBZ 1041W on your desk making it easy to read information add peripherals or to synchronize with your PC 21 USB 1 1 Type A Port x 2 22 USB Type B Port Non Operational for 1041W 23 DC IN jack IBZ 1041W Wireless Touch Panel Manual 2 3 The Battery and AC Adapter 2 3 Your IBZ 1041W has two power sources battery and AC To run your IBZ 1041W from the wall use the supplied AC adapter cable The battery charges when the Tablet is connected to the AC power The indicator on the front of your IBZ 1041W displays the battery status Indicator solid green Battery is fully charged Indicator solid orange Battery is charging Indicator off System is in the suspend mode When fully charged and not in use your IBZ 1041W battery has a two week life To check your battery level or to adjust the time before your battery switches off power schemes after the Tablet is continuously idle go to Start2Settings Control PanelPower or double click on the power icon in taskbar For further tips on optimizing your battery go to Start 2HelpSettings Power 2 4 The Stylus The Stylus has been specially designed for use with your IBZ 1041W IMPORTANT is strongly recommended that you use the provided stylus at all times fingers or other instruments may damage your s2. nternal Speakers nternal Microphone WIFI nternal 802 11b g Enclosure Water Resistant Plastic with built in stand Power Supply 19v DC brick supply Battery Life 3 1 2 hours full power continues operation Up to 8 hours with power saving mode settings Operating System Windows CE 5 0 Operating System IBZ 1041W Wireless Touch Panel Manual 9 Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and radiates radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation A CAUTION CAUTION Danger of explosion if an improper battery is substituted If a replacement is needed only replace with a manufacturer issued battery pack Do not dispose of the battery pack in a fire They may explode Check with local authorities for proper disposal instructions 10 Warranty Aurora Multimedia Corp Manufacturer warrants that this product is free of defects in both materials and workmanship for a period of 1 year as defined herein for parts and labor fr
3. To input data into this IBZ 1041W you can choose to use the Software Keyboard described below or an External USB Keyboard via a USB 1 1 port Software Keyboard To access Software Keyboard you need to press and hold for 2 seconds a black button located next to a wireless and a battery LED indicators When in Kiosk mode this is the only option to display Software Keyboard on the screen When in Desktop Mode the icon appearing in the taskbar provides you a Software Keyboard functions like a real keyboard The CAP key locks the keys to uppercase the Shift key switches the keys to uppercase for one click only Once finished with the handwriting and keyboard click on the icon in taskbar and select Hide Input Panel 3 2 Synchronization Connecting Other Devices Your IBZ 1041W is designed to support a number of external devices The two USB Type A ports on the left side let you add USB 2 0 keyboard mouse or Flash disk Whereas the built in SD Card slot allow you to read write memory cards from to the IBZ 1041W IBZ 1041W Wireless Touch Panel Manual 4 Getting Online 1 Double click the Internal WLAN icon in your taskbar l 2 12 02 Select the Wireless Information tab Select your preferred network AP and click the Connect button to associate INTERNAL_WLAN Information Wireles Information Select a network and press connect or right cli
4. do I restart my IBZ 1041W If it freezes hangs up or I just loaded new software If you need to restart you IBZ 1041W unscrew your stylus and hit the software reset button on the side of the Tablet If your IBZ 1041W is not responding to any commands that is it freezes or hangs you can use this same reset button The software reset button will not affect data on your IBZ 1041W system 1 If your system freezes or hangs and does not respond even after you hit the software reset button first remove the battery to restart the system If this does not help the situation you will need to use the hardware reset button Note that this will wipe all memory from your IBZ 1041W My screen is dirty how can I clean it without harm to the screen 2 Clean the screen with a soft clean cloth and commercial window cleaner that does not contain wax or abrasives Always apply the cleaner to the cloth not the screen If the display contains grease or some other contaminant use isopropyl alcohol instead of commercial cleaner Note paper toweling and other paper products are abrasive Be sure to use a clean cloth when wiping the screen IBZ 1041W Wireless Touch Panel Manual 8 Specifications Processor and Memory 32 bit Geode LX700 Microprocessor 128 RAM 128Mb Display 10 4 800 x 600 pixels Four Wire Touch Resistive Connections RJ 45 10 100 LAN e 2 USB 2 0 VGA DB 9 RS 232 Line Input Headphone
5. place the IBZ 1041W in an overhead compartment where it can slide around Do not drop your IBZ 1041W or subject it to mechanical shocks e Protect your IBZ 1041W from environmental hazards such as dirt dust food liquids temperature extremes and over exposure to sunlight e When you change environments rapidly in respect to temperature and humidity with your IBZ 1041W condensation may form on or within the Tablet To avoid potential damage to your IBZ 1041W allow sufficient time for the moisture to evaporate before using e When disconnecting cables from your IBZ 1041W be sure to pull on the connector or the strain relief loop not on the cable itself As you pull keep it evenly aligned to avoid bending the connector pins Never force a connector into a port Make sure the connector and port are aligned correctly e Before you clean your IBZ 1041W turn it off remove the battery and unplug the power source e Clean your computer with a soft cloth dampened with water rather than with liquid or aerosol cleaners e Clean the screen with a soft clean cloth and commercial window cleaner that does not contain wax or abrasives Always apply the cleaner to the cloth not the screen If the display contains grease or some other contaminant use isopropyl alcohol instead of commercial cleaner IBZ 1041W Wireless Touch Panel Manual 1 3 Checklist Check to see that the package your IBZ 1041W came in includes these items e BZ 1041W e Cr
6. IBZ 1041W Wireless Touch Panel Manual Aurora Multimedia REFERENCE MANUAL N NU Microphone Control Main Control Output Level Control F Projector 5 gt DVD VCR Control IBZ 1041W 10 4 Wireless Touch Panel Revision 2009 09 02 tel 732 591 5800 fax 732 591 5801 205 Commercial Court Morganville NJ 07751 www auroramultimedia com O Copyright 2009 Aurora Multimedia Inc All rights reserved including the right to reproduce this guide or parts thereof in any form without the express written permission of Aurora Multimedia Inc Trademarks and registered trademarks are the properties of their respective owners Software and hardware features and specifications subject to change without notice IBZ 1041W Wireless Touch Panel Manual Table of Content TE GET TING STARTED E 3 TAO WELCOMES aa Ia toate 3 1 2 SAFETY INSTRUCTIONS AND CARE OF YOUR IBZ 104 IW ssseeeeeeeeeeen eene mimina nennen esseri 3 1 3 WA Ka er RO eo 5 2 GETTING TO KNOW YOUR IBZ 1041 W sscccsssscssssccesssccesssccessssccssscccesssccesscccesscccesssccesssceseeseeees 6 2 MOPARTS iis eniti n the cecal br Sauna Zak Sad Sava aa ka kawa aa A e UE 6 DAD HE Or NDA MR PE EE ML 8 2 3 THE BATTERY ADAPTER ii ew re Er er E e er c duet eee Pu Er eb Yee E einn 9 QA THE STYLUS eerte reete ease trei tem eie ia
7. adle AC Adapter Power Cord Battery Pack e Stylus ny Why e User Manual IBZ 1041W Wireless Touch Panel Manual 2 Getting to Know Your IBZ 1041W 2 1 Parts Names Your IBZ 1041W features powerful functions and connectivity for you to control your system via a touch panel interface This section outlines your IBZ 1041W s components Top Side e On Off Suspend Resume Switch e 2 Future Expansion e 3 SD Card Slot e Stylus Storage Right Side e 5 External Microphone jack e External Headphone jack e 7 VGA Out Connector e 8 5 232 Connector IBZ 1041W Wireless Touch Panel Manual Left Side e 9 RJ 45 LAN Port e 10 USB 2 0 Type A Port x2 e 11 DC IN Jack Front e 12 Function Keys Button e 13 4 way Mover Button e 14 Keyboard Button e 15 Wireless LED Indicator e 16 Battery LED Indicator e 17 Internal Speakers e 18 Internal Microphone IBZ 1041W Wireless Touch Panel Manual Back 19 Hardware Software Reset Switch 20 Battery Latches Left one is also a Suspend Resume switch
8. ceesessaeeeceeeesas 14 vaueIBEIeeunicm s ess 15 SPECIFICATIONS ii 16 9 REGULATORY NOTICES ii eE EEEE AAEE ERE ER eies 17 n nl 17 1 IBZ 1041W Wireless Touch Panel Manual Getting Started 1 1 Welcome Congratulations With your new IBZ 1041W you will be able to control your WACI control system or just about any web server based system The IBZ 1041W has a unique firmware build of Windows CE which secures the device for the specific intent of controlling devices while preventing access to critical setup and files When the IBZ 1041W is turned on it will do only one thing control your custom system without worries of it controlling you Your IBZ 1041W also gives you freedom with easy access to the Internet and the 800X600 SVGA screen offers high resolution for all your control system uses This manual will guide you through the unit s simple set up introduce you to its range of features and help you source extra information 1 2 Safety Instructions and Care of your IBZ 1041W A CAUTION Danger of explosion if an improper battery is substituted If a replacement is needed only replace with a manufacturer issued battery pack e During normal usage and charging the battery pack heats up This is caused by energy that has been generated and a chemical charge that has occurred inside the battery pack This is not a cau
9. ck for more options To add a new network double click New IP Information IP Y Add New 00074038A9DE preferred c3 802 11b SSID preferred i Allenon4 NMRA Status Connected to 802 11b SSID Signal Strength Good Notify me when new wireless networks are available Advanced View Log 5 Upgrading Firmware To upgrade firmware on your IBZ1041W please follow these steps 1 2 3 4 5 6 Get a Flash drive with at least 64MB Download IBZ1041W firmware from our website http www auroramultimedia com Extract your NK bin file and copy it to your Flash drive DO NOT put it into any folder Plug in your Flash drive into your IBZ1041W panel After a few seconds you will see a window prompt click YES to upgrade firmware After it is completed you will be asked to remove your Flash drive and to Reboot your panel IBZ 1041W Wireless Touch Panel Manual 6 Configuring IBZ 1041W with a WACI control system 6 1 Changing Homepage To change your homepage go to Internet Options Start2Settings Control PanelInternet Options Type the address in the Start Page box and click OK Restart the panel and it will automatically go to the Kiosk mode with the new homepage set by the user If your WACI has an IP address of 192 168 1 110 and your index html file resides directly inside wwwpub directory on your WACI e g wwwpub index html then your homepage a
10. creen If you find that your IBZ 1041W is not responding properly to your taps you may need to recalibrate your screen To do this go to Start2Settings Control Panel Stylus Once there select the Calibration tab and follow the instructions Your stylus can be conveniently stored in the side of your IBZ 1041W The Suspend Resume switch on the topside of your IBZ 1041W when in the Suspend position ensures that the touch panel isn t accidentally turned on Sliding the switch to the ON position resumes the Tablet IBZ 1041W Wireless Touch Panel Manual 2 5 Touch screen Display Your IBZ 1041W is equipped with a touch screen You can use the stylus that works like a mouse to click or double click a selected icon and open it In addition tap your touch panel desktop with your stylus for over one second and it will act as right click 2 6 Display Properties This function allows you to set the background on your desktop and the colors displayed on your interface To access these functions go to Start Settings Control PanelDisplay Background or tap the desktop with your stylus over one second and it will act as right click to run the Display properties 2 7 The Cradle The cradle lets you dock your IBZ 1041W making it easy to use your desk to read information or to add peripherals such as a keyboard or a mouse IBZ 1041W Wireless Touch Panel Manual 3 Managing Your Information 3 1 Data Input
11. cturer s discretion Express shipping will be at the expense of the Purchaser If Purchaser resides outside the contiguous US return shipping shall be at Purchaser s expense No other warranty express or implied other than Manufacturer s shall apply Manufacturer does not assume any responsibility for consequential damages expenses or loss of revenue or property inconvenience or interruption in operation experienced by the customer due to a malfunction of the purchased equipment No warranty service performed on any product shall extend the applicable warranty period This warranty does not cover damage to the equipment during shipping and Manufacturer assumes no responsibility for such damage This product warranty extends to the original purchaser only and will be null and void upon any assignment or transfer
12. ddress will only be your WACT s IP address http 192 168 1 110 If your index html file is not directly in wwwpub directory then when setting your homepage you need to specify the name of the folder where index file is located e g http 192 168 1 110 yourproject index html 6 2 Accessing ADMIN Setup Mode By default when panel is powered it goes into a Kiosk mode and a message Welcome to the Ibrowz is displayed To leave this mode and change your homepage you need to press and hold the upper left touch screen area for about 3 5 seconds After that a window will pop up asking you to type your password to get to the Desktop mode Password admin Click on Enter and Exit To Desktop 6 3 Changing IP Address To change an IP address you need to go to the Network and Dial up Connections StartSettings Control Panel Network and Dial up Connections Open up the Network icon select Specify an IP address and type your new IP address Subnet Mask and Default Gateway After you are done click OK and changes would be applied immediately 6 4 Calibrating the Panel To calibrate your panel go to Stylus option in Control Panel Start2Settings Control Panel Stylus and click on Calibration tab Click on Recalibrate button Recalibration involves tapping the center of a target and the panel measures new settings Recalibration is needed when you use your panel for the first time after resetting it or wh
13. e lee OVER RETE EET OE 9 2 9 TOUCH SCREEN DISPLAY ieena ed teer e Der sexe o e re eripe ree Re e agen bes ene EXE ev ee 10 2 6 DISPLAY PROPERTIES nie D HERD RB HI RE EROR OH IB IRE OTRAS 10 2 IG DHECRADEES we citet et ees rn as aet S e ot E dequo te ier 10 3 MANAGING YOUR INFORMATION s essseeeeeeeeeeeeeeeeeeeeeeeeees 11 S To ATASINPUT S SUE E so A M TRE E KIWA 11 3 2 SYNCHRONIZATION CONNECTING OTHER DEVICES eene nnne nnn n nenas ess ss na eani se e nnns 11 4 GETTING ONLINE a Ee AA 12 5 UPGRADING FIRMWA Riwa ea esae UR ENEE Cu eae Tua ura aao EEA aiia aean 6 CONFIGURING IBZ 1041W WITH A WACI CONTROL SYSTEM 5 1 GHANGING HOMEPAGE digerere u IL E ER C HX GERUNT YU GER N 13 5 2 AccESSING ADMIN SETUP va tee ei mt deed tok bu a seco pede eeu ve e STORE 13 3 92 CHANGING IP ADDRESS cete Permet teer e E e Deere eR er E E e iere e US 13 SA CALIBRATING THE PANEL A ee op oo 13 5 5 SAVING SETTINGS TO THE PERSISTENT MEMORY ccessccsceesessseececeessseeeeceeensaeeeccesensseeecesesssseeeecesesueeeeeeseeaees 14 5 6 RESTARTING THE PANEL ier tse E CH BOUE E REGENDI EGREGII 14 5 7 BooriNG KIOS K MODE 3 1 cicero terc E C Te gu Pe ee He DRE YR TEUER 14 5 8 CHANGING MAIN ADMIN PASSWORD cccsesecceccesssscececeessssceeccessssseeseesessaceecceeessaeeeecesseaeee
14. en after touching your screen with a stylus your mouse arrow is in a different place IBZ 1041W Wireless Touch Panel Manual 6 5 Saving Settings to the Persistent Memory To save settings go to Utility option in Control Panel Start Settings Control Panel Utility and click on Registry Manager tab Click on Backup button It might take a couple of seconds to save all the current settings 6 6 Restarting the Panel There are two ways to restart the panel Software and Hardware Reset The buttons to restart the panel are located on the back of device Software Reset is just like rebooting the system and does not reset any settings that might have been set on the device Hardware Reset is rebooting the system as well as resetting all settings on the panel 6 7 Booting to KIOSK Mode This option could be either enabled or disabled depending on your needs To enable disable it you need to be in Kiosk mode and follow instructions from step 5 1 but instead of Exiting to Desktop go to Change Settings You will be able to enable or disable Boot To Kiosk Mode option 6 8 Changing Main ADMIN Password Follow instructions from step 5 7 In the same window you will also be able to change your main administrator password IBZ 1041W Wireless Touch Panel Manual 7 Troubleshooting For problems with your IBZ 1041W to StartHelp This brings up a general user manual to reference Most questions will be able to be answered
15. from this resource Common Problems Frequently Asked Questions The IBZ 1041W will not turn on 1 sure the Suspend Resume switches are set to On Resume 2 Check if your Power settings in Control Panel are set to Switch state to Suspend Never 3 If device does not power on use the AC Adapter to plug the Tablet into the wall 4 Ifthis does not turn the Tablet on push the software reset button located at the rear panel See the previous section titled Parts Names I touch the screen with my stylus and the mouse arrow is in an entirely different place 1 This is a sure sign that you need to re calibrate your touch screen 2 Goto StartSettings Control PanelStylus 3 Click the calibration tab 4 Click recalibrate and follow the instructions How do I turn off my IBZ 1041W You can turn off your IBZ 1041W by simply going to the Start Menu and choosing Suspend This will put the device in standby mode You can also put unit into suspend by sliding the Suspend Resume switch to ON and hold for less than 2 seconds To resume your IBZ 1041W slide the Suspend Resume switch to ON position on the top of your Tablet and release Sliding Suspend Resume switch towards position for than 4 seconds will turn off your IBZ 1041W and ensure it isn t accidentally turned on by clicking on the buttons Nezt time unit is turned on it will take longer as it will need to do a full boot How
16. om date of purchase Motorized mechanical parts Hard Drives DVD etc mechanical parts buttons doors etc remotes and cables are covered for a period of 1 year Touch screen displays are covered for 1 year touch screen overlay components are covered for 90 days Supplied batteries are not covered by this warranty During the warranty period and upon proof of purchase the product will be repaired or replaced with same or similar model at our option without charge for parts or labor for the specified product warranty period This warranty shall not apply if any of the following A The product has been damaged by negligence accident lightning water act of God or mishandling or B The product has not been operated in accordance with procedures specified in operating instructions or C The product has been repaired and or altered by other than manufacturer or authorized service center or D The product s original serial number has been modified or removed or E External equipment other than supplied by manufacturer in determination of manufacturer shall have affected the performance safety or reliability of the product F Part s are no longer available for product In the event that the product needs repair or replacement during the specified warranty period product should be shipped back to Manufacturer at Purchaser s expense Repaired or replaced product shall be returned to Purchaser by standard shipping methods at Manufa
17. se for concern e You should charge batteries at temperatures from 10 C to 30 C from 50 F to 85 F Lower temperatures require a longer charging time e Do not carry a battery in your pocket purse or other container where metal objects could short circuit the battery pack The resulted excessive current flow can cause extremely high temperatures and may result in damage from burns e Do not use your IBZ 1041W in a wet environment for instance near a bathtub sink or any other place where there is risk of moisture e To help prevent electric shock plug the AC adapter into a three prong grounded power source If a two prong extension plug is absolutely needed use a 3 wire cable with properly grounded plugs e If your IBZ 1041W includes a modem PC Card disconnect the modem cable during electrical storms to avoid the remote risk of electrical shock from lightening via the telephone line e PC Cards may increase in temperature over an extended period of use Use care in handling these cards A Do not dispose of the battery pack in a fire They may explode Check with local authorities for proper disposal instructions IBZ 1041W Wireless Touch Panel Manual e When traveling never check your IBZ 1041W as baggage You can put your IBZ 1041W through an X ray security machine but never put your IBZ 1041W through a metal detector Have a charged battery with you in case you are asked to turn on the Tablet e When traveling do not
Download Pdf Manuals
Related Search