Home

User`s Manual

1. Page 1 v System event log interface The following table describes the labels in this screen To get the newest event logs and refresh this page ORing Industrial Networking Corp 34 System Warning SMTP Setting The SMTP is Short for Simple Mail Transfer Protocol Itis a protocol for e mail transmission across the Internet Please refer to RFC 821 Simple Mail Transfer Protocol system Warning SMTP Setting E mail Alert ET SMTP Configuration Sender E mail Address Mail Subject Automated Email Alert Dauthenticati n Recipient E mail Address 1 Recipient E mail Address 2 Recipient E mail Address 4 Poo System Warning SMTP Setting interface The following table describes the labels in this screen Enable Disable transmission system warning events by e mail The SMTP server IP address Mail Subject The Subject of the mail a Username the authentication username Password the authentication password Authentication Confirm Password re enter password Recipient E mail The recipient s E mail address It supports up to 6 Address recipients per mail Apply Click Apply to set the configurations ORing Industrial 35 Networking Corp e ay IPS 2000 Series User s Manual Gara omn IPS 2000 Series User s Manual System Warning Event Selection SYSLOG and SMTP are the two warning me
2. not a Pc Bo ca ee fom or too 1 O O Low w 15400 Null 0 0 0 0 0 15 4W 2 O O Low S 15400 Null 0 0 0 0 0 15 4W 3 O O Low w 115400 Null 0 0 0 0 0 15 4W 4 O O Low 115400 Null 0 0 0 0 0 15 4W The following table describes the labels in this screen Port Portnumber O Enable state Mark the blank to enable specific ports P O E function Power Limit From Set the Power Limit From Classification function for Classificaton each P O E ports The legacy detection is to identify the PD devices that did not follow the IEEE 802 3af standard their unique cid electrical signatures in order for the PoE switch can provide the power to those PD devices Priority Set port priority for the POE power management C critical 2 H High 3 L Low Set the power limit value The maximum value must Power Limit less 15400 Mode Display the PD current operation mode status sin aia ce inthis ORing Industrial 39 Networking Corp IPS 2000 Series User s Manual Display watt value Display power class When the Bypass classification Determined Class enable the class value will not show in here Apply Click Apply to set the configurations Technical Specifications Technology RSTP O Ring Ring redundancy peuple ing Dual Homing Fast recovery Ethernet Standards IEEE802 3 10BASE T IEEE802 3u 100BASE TX IEEE802 3x Flow Control and Back pressure IEEE802 1D Spanning tree protocol IEEE802 1w Ra
3. 2000 Series on DIN Rail Step 1 Slant the switch and mount the metal spring to DIN Rail Metal Spring Step 2 Push the switch toward the DIN Rail until you heard a click sound ORing Industrial Networking Corp 4 a ay IPS 2000 Series User s Manual 2 2 Wall Mounting Installation Each switch has another installation method for users to fix the switch A wall mount panel can be found in the package The following steps show how to mount the switch on the wall 2 2 1 Mount IPS 2000 Series on wall Step 1 Remove DIN Rail kit Step 2 Use 6 screws that can be found in the package to combine the wall mount panel Just like the picture shows below ORing Industrial 5 Networking Corp e ay IPS 2000 Series User s Manual The screws specification shows in the following two pictures In order to prevent switches from any damage the screws should not larger than the size that used in IPS 2000 series switches O Step 3 Mount the combined switch on the wall ORing Industrial Networking Corp 6 r agi e ons a IPS 2000 Series User s Manual Hardware Overview 3 1 Front Panel The following table describes the labels that stick on the IPS 2000 series 10 100 RJ 45 10 100Base T X RJ 45 fast Ethernet ports support auto negotiation fast Ethernet Default Setting ports Speed auto Duplex auto Flow control disable Fiber port 100BaseFX for IPS 2042F
4. ORing Industrial Networking Corp IPS 2000 Series User s Manual not including STP mathematic calculation False is including the STP mathematic calculation Apply Click Apply to set the configurations NOTE Follow the rule to configure the MAX Age Hello Time and Forward Delay Time 2 x Forward Delay Time value 1 gt Max Age value gt 2 x Hello Time value 1 RSTP Information Show RSTP algorithm result at this table RSTP Information Root Bridge Information Bridge ID OOS00012458 4125 Root Priority 32768 Root Port Root Root Path Cost 0 Max Age Time 20 Hello Time 2 Forward Delay Time 15 Port Information Port Priority OperP2P OperEdge STP Neighbor State Role 128 True True False Disabled Disabled 128 True True False Disabled Disabled 128 True True False Forwarding Designated Port 04 200000 128 True True False Disabled Disabled Port 05 200000 128 True True False Disabled Disabled Port 06 200000 128 True True False Disabled Disabled RSTP Information interface ORing Industrial 29 Networking Corp 5 1 6 SNMP Configuration Simple Network Management Protocol SNMP is the protocol developed to manage nodes servers workstations routers switches and hubs etc on an IP network SNMP enables network administrators to manage network performance find and solve network problems and plan for network growth Network management systems learn of problems by receiving traps or change n
5. Series P O E Port Port 1 to port 4 contain PSE function of IEEE802 3af P O E Push reset button 2 to 3 seconds to reset the switch ORing Industrial 7 Networking Corp ae ay IPS 2000 Series User s Manual IPS 2000 Series User s Manual IPS 2042FX Seires es 10 l I 2 3 4 5 6 12 10 100M i LED for PWR1 When the PWR1 links the green led will be light on LED for PWR2 When the PWR2 links the green led will be light on LED for PWR3 When the PWR3 links the green led will be light on LED for R M Ring master When the LED light on it means that the switch is the A ring master of O Ring LED for Ring When the led light on it means the O Ring is activated LED for Fault Relay When the fault occurs the amber LED will be light on Reset button Push the button 3 seconds for reset 5 seconds for factory default 10 100Base T X Ethernet ports LED for Ethernet ports status O XD Y 10 Model name 11 100BaserFX fiber port 12 LED for fiber port 13 LED forP O E ORing Industrial Networking Corp 8 IPS 2000 Series User s Manual IPS 2042TX IPS 2042TX PRI PWR PWR RM Ring Fauli ao te x le bj 1 LED for PWR1 When the PWR1 links the green led will be light on LED for PWR2 When the PWR2 links the green led will be light on LED for PWR3 When the PWR3 links the green led will be light on LED for R M Ring master When the LED light on it me
6. following table lists the different location time zone for your reference AST Atlantic Standard Sam ORing Industrial Networking Corp 18 IPS 2000 Series User s Manual EST Eastern Standard 5 hours 7 am CDT Central Daylight CST Central Standard 6 hours 6 am MDT Mountain Daylight MST Mountain Standard 7 hours 5 am PDT Pacific Daylight PST Pacific Standard 8 hours 4am ADT Alaskan Daylight HAW Hawalian Standard 2 am CET Central European FWT French Winter MET Middle European MEWT Middle European Winter SWT Swedish Winter EET Eastern European 2 hours 2pm USSR Zone 1 BT Baghdad USSR Zone 3 hours 3 pm 2 WAST West Australian 7 hours 7pm Standard CCT China Coast USSR 8 hours 8 pm Zone 7 JST Japan Standard 9 hours 9pm USSR Zone 8 1 hour 1 pm EAST East Australian 10 hours 10 pm Standard GST ORing Industrial 19 Networking Corp IPS 2000 Series User s Manual Guam Standard USSR Zone 9 IDLE International Date Line NZST New Zealand 12 hours Midnight Standard NZT New Zealand Spiny RENERE Set the SNTP server IP address Address Daylight Saving Set up the Daylight Saving beginning time and Daylight Saving Period ending time Both will be different each year Daylight Saving Offset Switch Timer Display the switch current time Apply Click Apply to set the configurations Set up the offset time
7. http 192 168 10 1 E co Links The login screen appears Key in the username and password The default username and password is admin 5 Click Enter or OK button then the main interface of the Web based management appears ORing Industrial Networking Corp 14 IPS 2000 Series User s Manual index htm User name 7 admin a Password cones Remember my password Login screen Main Interface Industrial 6 port Lite managed Ethernet Switch with 6x 10 100TX System Industrial 6 port Lite managed Ethernet Switch with Description 6x 10 100TX System OID 1 3 6 1 4 1 25972 0 1 7 Ed v1 00 emel Version v1 04 device MAG 00 12 45 87 41 25 Enable Location Alert Main interface 5 1 2 Basic Setting 5 1 2 1 Switch setting Switch Setting ec Industrial 6 port Lite managed Ethernet Switch with 4x 10 100TX System OID 1 3 6 1 4 1 25972 0 1 9 Firmware Version v1 00 Kernel Version v1 04 E 00 AA BB CC 11 22 Switch setting interface ORing Industrial 15 Networking Corp IPS 2000 Series User s Manual The following table describes the labels in this screen System Name Assign the name of switch The maximum length is 64 bytes System o o Display the description of switch Description System Location Assign the switch physical location The maximum length is 64 bytes System Contact Enter the name of cont
8. rule The number of seconds a bridge waits without receiving Spanning tree Protocol configuration messages before attempting a reconfiguration Enter a value between 6 through 40 The time that controls switch sends out the BPDU packet to check RSTP current status Enter a value between 1 through 10 The number of seconds a port waits before changing from its Rapid Spanning Tree Protocol learning and listening states to the forwarding state Enter a value between 4 through 30 The cost of the path to the other bridge from this transmitting bridge at the specified port Enter a number 1 through 200000000 Decide which port should be blocked by priority in LAN Enter a number O through 240 The value of priority must be the multiple of 16 Some of the rapid state transactions that are possible within RSTP are dependent upon whether the port concerned can only be connected to exactly one other bridge i e It is served by a point to point LAN segment or it can be connected to two or more bridges i e It is served by a shared medium LAN segment This function allows the P2P status of the link to be manipulated administratively True means P2P enabling False means P2P disabling The port is directly connected to end stations and it cannot create bridging loop in the network To configure the port as an edge port set the port to True Admin Non STP The port includes the STP mathematic calculation True is
9. the switch status on remote site When events occurred the warning message will send to your appointed server E MAIL or relay fault to switch panel 5 1 8 1 Fault Alarm When any selected fault event is happened the Fault LED in switch panel will light up and the electric relay will signal at the same time Fault Alarm Power Failure PWR 1 PWR 2 Port Link Down Broken DJ Port 1 DPort 2 Port 3 C1 Port 4 C Port 5 Part 6 System Warning SYSLOG Setting The SYSLOG is a protocol to transmit event notification messages across networks Please refer to RFC 3164 The BSD SYSLOG Protocol system Warning SYSLOG Setting SYSLOG Mode Disable SYSLOG Server IP Address System Warning SYSLOG Setting interface The following table describes the labels in this screen SYSLOG Mode ES Disable disable SYSLOG Client Only log to local system m Server Only log to a remote SYSLOG server ORing Industrial 33 Networking Corp e ay IPS 2000 Series User s Manual IPS 2000 Series User s Manual po a Both log to both of local and remote server SYSLOG Server IP The remote SYSLOG Server IP address Address Apply Click Apply to set the configurations System Event LOG If system log client is enabled the system event logs will show in this table system Warning SYSLOG List 4 Jan 1 00 10 06 System Log Enable 2 Jan 1 00 10 06 System Log Server IP 0 0 0 0
10. to default configuration Click Reset to reset all configurations to the default value You can select Keep current IP address setting and Keep current username amp password to prevent IP and username amp password from default 5 1 2 8 System Reboot System Reboot Please click Reboot button to restart switch device System Reboot interface ORing Industrial Networking Corp 22 5 1 3 Port Configuration 5 1 3 1 Port Control By this function you can set the state speed duplex flow control and security of the port Port Control o State Speed Duplex Flow Control Port 01 Enable AL AutoNegotiation 1 Be Disable Ml Port 02 Enable AutoNegotiation v Disable Y wi Port 03 Enable Enable AutoNegotiation w Disable emt 4 Enable sone y A AutoNegotiation J Disable Disable i Disable y Port Control interface The following table describes the labels in this screen Port number for setting state Enable Disable the Enable Disable the port half mode Flow Control Support symmetric and asymmetric mode to avoid packet m Eea Apply Click Apply to set the configurations ORing Industrial 23 Networking Corp a IPS 2000 Series User s Manual IPS 2000 Series User s Manual 5 1 3 2 Port Status The following information provides the current port status Port Status Port No Type Link State Speed Duplex Flow Cont
11. Industrial P O E Lite Managed Ethernet Switch IPS 2000 Series User s Manual Version 1 0 May 2008 Oring o ORing Industrial Networking Corp 4F NO 3 Lane235 Baociao Rd Sindian City Taipei County 23145 Taiwan R O C Tel 886 2 2918 3036 Fax 886 2 2918 3084 Website www oring networking com E mail support oring networking com Table of Content Getting to AA en 3 1 1 About the IPS 2000 Series Smart Industrial SwitCh ooooooocnoooccnonacononacononaconannccnnnncono 3 1 2 SOWAS ROQUES arras 3 1 3 Fen IVY ASS UI OS dada 3 Hardware IAS OA tica 4 2 1 installation SWitG a on DINSA lr 4 Zh Mount 1PS 2000 Series on DIN Ratlia ni is 4 2 2 vall MOUMUIAG INS 5 224 MountTPS 2000 Senes on Walla ir tia 5 Hardware OvVerVi Wir 7 3 1 A ecm E raster SunEr era rey e om ett tere 7 3 2 FON Pano LEDS ociscene a ia ct Eo 10 3 3 BOHOM Ranee dd et ee ee 11 3 4 nl ert E Er E eee Se en AU SR re rte Og RENE ne RA ea a 11 65 A O T Se are Ree Sm OR Een open omRr er rere 12 4 1 A O O A cE ee 12 4 1 1 100BASE TX 10BASE T Pin Assignments 0 cccccccccccssseessssssseseeeeceeeecccccseceessecesssssessseseeenss 12 4 2 A re en ee eee eee ne A ener eee 13 WEB AIAG MEA a 14 5 1 Configuration DY Web BhOWSEN dada 14 Skl About Web based Manage Meni cca eect tenio iaa 14 liz BASE Nod 15 5 1 2 1 AE e EE EE O A rr nnnet ee tee 15 342 2 AMI PAS SW OL sh tees dada 16 5212 3 MEA A E 17 5 1 2 4 SNTC O
12. ORing Industrial Networking Corp 20 5 1 2 5 Backup amp Restore You can save current EEPROM value of the switch to TFTP server then go to the TFTP restore configuration page to restore the EEPROM value Backup amp Restore Restore Configuration TFTP Server IP Address 192 168 10 66 Restore File Name sata bin Backup Configuration TFTP Server IP Address 192 168 10 66 Backup File Name databin_ Hee Backup amp Restore interface The following table describes the labels in this screen TFTP Server IP Address Fill in the TFTP server IP Restore File Name Fill the file name Click restore to restore the configurations Restore File Name Fill the file name Click restore to restore the configurations Click backup to backup the configurations ORing Industrial 21 Networking Corp a ay IPS 2000 Series User s Manual IPS 2000 Series User s Manual 5 1 2 6 Upgrade Firmware Upgrade Firmware allows you to update the switch firmware Before updating make sure you have your TFTP server ready and the firmware image is on the TFTP server Upgrade Firmware Trip Server IP 192 168 10 66 Firmware File Name image bin ESE Update Firmware interface 5 1 2 7 Factory Default Factory Default Keep curent IF address setting Keep current username amp password Factory Default interface Reset switch
13. ach O Ring to the normal switches in RSTP mode Apply Click Apply to set the configurations Note We don t suggest you to set one switch as a Ring Master and a Coupling Ring at the same time due to heavy load ORing Industrial Networking Corp 26 IPS 2000 Series User s Manual 5 1 5 RSTP The Rapid Spanning Tree Protocol RSTP is an evolution of the Spanning Tree Protocol It provides faster spanning tree convergence after a topology change The system also supports STP and the system will auto detect the connected device that is running STP or RSTP protocol 5 1 5 1 RSTP setting You can enable disable the RSTP function and set the parameters for each port RSTP Setting RSTP Mode Bridge Configuration eom a 200000 a A RSTP Setting interface ORing Industrial 21 Networking Corp IPS 2000 Series User s Manual The following table describes the labels in this screen You must enable or disable RSTP function before configuring the related parameters RSTP mode Priority 0 61440 Max Age 6 40 Hello Time 1 10 Forwarding Delay Time 4 30 Path Cost 1 200000000 Priority 0 240 Admin P2P Admin Edge A value used to identify the root bridge The bridge with the lowest value has the highest priority and is selected as the root Ifthe value changes you must reboot the switch The value must be multiple of 4096 according to the protocol standard
14. act person or organization Firmware Display the switch s firmware version Version Display the kernel software version MAC Address Display the unique hardware address assigned by manufacturer default 5 1 2 2 Admin Password Change web management login username and password for the management security issue Admin Password User Name admin New Password mala Confirm Password dese Admin Password interface The following table describes the labels in this screen Label Description Key in the new username The default is admin New Password Key in the new password The default is admin Confirm Re type the new password password Apply Click Apply to set the configurations ORing Industrial Networking Corp 16 5 1 2 3 IP configuration You can configure the IP Settings and DHCP client function through IP configuration IP Configuration DHCP Client Disable IP Address 192 168 10 1 Subnet Mask 255 255 255 0 Gateway 192 168 10 254 L IP Configuration interface The following table describes the labels in this screen Description To enable or disable the DHCP client function When DHCP client function is enabling the switch will assign the IP address from the network DHCP server The default IP address will be DHCP Client replaced by the IP address which the DHCP server has assigned After clicking Apply button a popu
15. al Cables 4 1 Ethernet Cables The IPS 2000 series switches have standard Ethernet ports According to the link type the switches use CAT 3 4 5 5e UTP cables to connect to any other network device PCs servers switches routers or hubs Please refer to the following table for cable specifications Cable Types and Specifications 10BASE T 3 4 5 100 ohm UTP 100 m 328 ft RJ 45 100BASE TX 5 100 ohm UTP UTP 100 m 328 ft 4 1 1 100BASE TX 10BASE T Pin Assignments With 100BASE TX 10BASE T cable pins 1 and 2 are used for transmitting data and pins 3 and 6 are used for receiving data RJ 45 Pin Assignments E DONNA INSI TC EII O e O e The IPS 2000 series switches support auto MDI MDI X operation You can use a straight through cable to connect PC and switch The following table below shows the 10BASE T 100BASE TX MDI and MDI X port pin outs MDI MDI X pins assignment TD transmit RD receive TD transmit RD receive ORing Industrial Networking Corp 12 IPS 2000 Series User s Manual RD receive TD transmit PB RD receive TD transmit 8 Not used Not used Note and signs represent the polarity of the wires that make up each wire pair 4 2 Fibers The following two models IPS 2042FX MM IPS 2042FX SS have fiber optical ports The fiber optical ports are in multi mode 0 to 2 km 1310 nm 50 125 um 62 5 125 um and single mode with SC connector Please remember th
16. ans that the switch is the ring gt mp Y master of O Ring LED for Ring When the led light on it means the O Ring is activated LED for Fault Relay When the fault occurs the amber LED will be light on Reset button Push the button 3 seconds for reset 5 seconds for factory default 10 100Base T X Ethernet ports LED for Ethernet ports status O ON DO 10 Model name 11 10 100Base T X Ethernet ports 12 LED for Ethernet ports status ORing Industrial 9 Networking Corp IPS 2000 Series User s Manual 3 2 oe Panel LEDs power module 1 Green activated DC power module 2 Green On activated Green Power jack activated O Ring topology has Slowly blinking cuits problem Fast blinking O Ring work normally Fault relay Power failure or Amber Port down fail 10 100Base T X Fast Ethernet ports LNK ACT Green A Data transmitted Fiber ports ORing Industrial Networking Corp 10 IPS 2000 Series User s Manual 3 3 Bottom Panel The bottom panel components of IPS 2060 IPS 2042FX Series are showed as below 1 Terminal block includes PWR1 PWR2 12 48V DC and Relay output 1A 24VDC 2 Power jack for PWR3 12 45VDC IPS 2060 IPS 2042F Series 3 4 Rear Panel The rear panel components of IES 2000 are showed as below 1 Screw holes for wall mount kit 2 Din Rail kit ORing Industrial 11 Networking Corp ae ay IPS 2000 Series User s Manu
17. at the TX port of Switch A should be connected to the RX port of Switch B EN TX RX a CAN y 5 Fiber cord e i C ee sia ka RX IX ee ORing Industrial 13 Networking Corp Gon mn IPS 2000 Series User s Manual WEB Management Configuration by Web Browser This section introduces the configuration by Web browser 5 1 1 About Web based Management Inside the CPU board of the switch an embedded HTML website resides in flash memory It contains advanced management features and allows you to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer The Web Based Management supports Internet Explorer 5 0 It is based on Java Applets with an aim to reduce network bandwidth consumption enhance access speed and present an easy viewing screen Note By default IE5 0 or later version does not allow Java Applets to open sockets You need to explicitly modify the browser setting in order to enable Java Applets to use network ports Preparing for Web Management The default value is as below IP Address 192 168 10 1 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 254 User Name admin Password admin System Login 1 Launch the Internet Explorer 2 Type http and the IP address of the switch Press Enter File Edit View Favorites Tools Help ae Back gt El a A E Search 3 7 Favorites O As El A E A Address
18. der wide temperature and dusty environment IPS series Support Power over Ethernet a system to transmit electrical power along with data to remote devices over standard twisted pair cable in an Ethernet network Each IPS switch has 4 X 10 100TX PSE Power Sourcing Equipment ports PSE is a device switch or hub for instance that will provide power in a PoE setup The IPS 2000 series switch can be managed by WEB and a useful Window Utility we called Open Vision Open Vision is powerful network management software The friendly and powerful interface helps you to configure multiple switches and monitor their status at the same time 1 2 Software Features World s fastest Redundant Ethernet Ring Recovery time lt 10ms over 250 units connection Supports Ring Coupling Dual Homing and RSTP over O Ring Support fast recovery mode Easy to configure Web Windows utility Windows utility Open Vision for network management 1 3 Hardware Features m Wide Operating Temperature 40 to 70 C m Storage Temperature 40 to 85 C E Operating Humidity 5 to 95 non condensing NW 10 100Base T X Ethernet port M 100Base FX Fiber port ORing Industrial 3 Networking Corp ae ay IPS 2000 Series User s Manual Hardware Installation 2 1 Installation Switch on DIN Rail Each switch has a DIN Rail kit on rear panel The DIN Rail kit helps switch to fix on the DIN Rail It is easy to install the switch on the DIN Rail 2 1 1 Mount IPS
19. e Remove Remove trap server profile ORing Industrial 31 Networking Corp ae ay IPS 2000 Series User s Manual 5 1 7 VLAN A Virtual LAN VLAN is a logical network grouping that limits the broadcast domain which allows you to isolate network traffic Only the members of the VLAN will receive traffic from the same members of VLAN Basically creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch However all the network devices are still plugged into the same switch physically The switch supports port based VLAN only 5 1 7 1 VLAN Configuration Port Based Packets can go among only members of the same VLAN group Note all unselected ports are treated as belonging to another single VLAN If the port based VLAN enabled the VLAN tagging is ignored Port Base VLAN oooh om E E a a a n m au Group 3 C eee ee O TI A fe cs E E E E E E E E E E E A VLAN Configuration Port Based VLAN interface The following table describes the labels in this screen Mark the blank to assign the port into VLAN group Apply Click Apply to set the configurations ORing Industrial Networking Corp 32 e ay IPS 2000 Series User s Manual 5 1 8 Warning Warning function is very important for managing switch You can manage switch by SYSLOG E MAIL and Fault Relay It helps you to monitor
20. ing Por ist Ring Port Port01 w Control Port Portod 2nd RingPort Port 02 w Portos we O Ring interface The following table describes the labels in this screen Mark to enable O Ring Ring Master There should be one and only one Ring Master in a ring However if there are two or more switches which set Ring Master to enable the switch with the lowest MAC address will be the actual Ring Master and others will be Backup Masters ORing Industrial 25 Networking Corp IPS 2000 Series User s Manual 1 Ring Port The primary port when this switch is Ring Master 2 Ring Port The backup port when this switch is Ring Master Coupling Ring Mark to enable Coupling Ring Coupling Ring can be used to divide a big ring into two smaller rings to avoid effecting all switches when network topology change It is a good application for connecting two O Rings Coupling Port Link to Coupling Port of the switch in another ring Coupling Ring need four switch to build an active anda backup link Set a port as coupling port The coupled four ports of four switches will be run at active backup mode Control Port Link to Control Port of the switch of the same ring Control Port used to transmit control signals Dual Homing Mark to enable Dual Homing By selecting Dual Homing mode O Ring will be connected to normal switches through two RSTP links ex backbone Switch The two links work as active backup mode and connect e
21. mation to other nodes on the network and store the information it discovers LLDP Configuration LLDP Protocol Disable Her The following table describes the labels in this screen LLDP Protocol Enable or Disable LLDP function LLDP Interval The interval of resend LLDP by default at 30 seconds Apply Click Apply to set the configurations 5 1 12 Power over Ethernet P O E The following interface is the PoE setting interface There are 4 ports port 1 to port 4 can be set as PSE Power Supply Equipment ports Power over Ethernet Maximum Power Available 200 Actual Power Consumption OW System Power Limit 200 w Main Supply Voltage 480 dv Firmware Version 2 04 Port Knockoff Disabled AC Disconnect Capacitive Detection ark Apply The following table describes the labels in this screen Maximum Power l l l l Display the maximum power available Available ORing Industrial Networking Corp 38 e IPS 2000 Series User s Manual IPS 2000 Series User s Manual System Power Limit Set the system power limit Actual Power l l Display the actual power consumption Consumption Mark the blank to enable Pork Knock off Disabled function AC Disconnect Mark the blank to enable AC Disconnect function Mark the blank to enable Capacitive Detection function Stat Mark the blank to enable P O E function Click Apply to set the configurations
22. nE UT AION spar dasa ae tot tant aol Oaaae Maines tanto want tansaet a atoms oan laos esciess 18 12d BACKUP GC RES esoo 21 5 1 2 6 Di iri A A A cui onatiianes 22 ala POD D 01 Neem renner nn neem unr Cena ORT rr en Meret onT en Saar A eel et ere Ch 22 5 1 2 8 SYSlCMINCDOOL espre EEEE T 22 IS OH Controle 23 dal A A eres ee eee cers een Ree ne Sra en ne eure er etree re ny eee eee 23 5 1 3 2 POC SCA vse tine sane ees ae wee ecue ened vensbiea saree sees vane eeegomaedouenc teas apomenaeamcee 24 fel Bes RE E a O 24 5 1 4 1 Past RECOVGry Modena sn 24 5 1 4 2 O A enemies 25 ES RSP O 21 5 1 5 1 IRS PP Set WS AA Io E ite omens nese o II te saanemst omnes eecapnets 21 ILo SNMP CONSI ON aaa des 30 ILOLE NM ASE UN a a sal cen ce ans 30 5 1 6 2 SNMP TDS UNA oe So 31 edge A A e 32 5 1 7 1 VIAN Contisuration Port Base aiia a A a a er J2 Slee Warna oei II A e men MMe et eT ne ene mTeT oT Te 33 5 1 8 1 A En pee Hee tte renee en eNOS 33 DO ROMP ANG OPEP OPE EE EE ECO 37 5 1 10 Save Contour dado dd 37 5 1 11 A A neE tel cate E tcl ds ilieled oanucn nue tabal tele 38 5 1 12 Power Over Feme P OEE an AA 38 Technical SHPSCIICALIOINS s eirrsesnorreenscnerersesrar eerror seeren are reran E aE N EENE Er oarre E OVEA EEVEE EEEa rE aseo eiS 40 Getting to Know Your Switch 1 1 About the IPS 2000 Series Smart Industrial Switch The IPS 2000 series switch is a cost effect and powerful industrial switch The switch has many features it can work un
23. otices from network devices implementing SNMP 5 1 6 1 SNMP Agent Setting You can set SNMP agent related information by Agent Setting Function SNMP Agent Setting Community String Privilege public Read Only w private Read and Write we l I Read Only The following table describes the labels in this screen SNMP Agent Setting SNMP Community should be set for SNMP Four sets of Community String Privilege are supported Each Community String is maximum 32 characters Keep empty to remove this Community string ORing Industrial Networking Corp 30 e ay IPS 2000 Series User s Manual 5 1 6 2 SNMP Trap Setting A trap manager is a management station that receives traps the system alerts generated by the switch If no trap manager is defined no traps will issue Create a trap manager by entering the IP address of the station and a community string To define management stations as trap manager and enter SNMP community strings and selects the SNMP version SNMP Trap Setting Trap Server Setting Server IP Community Trap Version vi Ovzc Trap Server Profile Server IP Community Trap Version none The following table describes the labels in this screen Label Description Server IP The server IP address to receive Trap Community Community for authentication Trap Version Trap Version supports V1 and V2c Add trap server profil
24. p dialog will show up to inform you when the DHCP client is enabling The current IP will lose and you should find the new IP on the DHCP server Assign the subnet mask for the IP address If DHCP client Assign the IP address that the network is using If DHCP client function is enabling you do not need to assign the IP address IP Address The network DHCP server will assign the IP address for the switch and it will be displayed in this column The default IP is 192 168 10 1 function is enabling you do not need to assign the subnet mask Ca Assign the network gateway for the switch The default gateway atewa is 192 168 10 254 DNS1 Assign the primary DNS IP address DNSZ o Assign the secondary DNS IP address Apply Click Apply to set the configurations ORing Industrial 17 Networking Corp ae IPS 2000 Series User s Manual oon IPS 2000 Series User s Manual 5 1 2 4 SNTP Configuration The SNTP Simple Network Time Protocol settings allow you to synchronize switch clocks in the Internet SNTP Configuration SNTP Configuration interface The following table describes the labels in this screen SNTP Client Enable or disable SNTP function to get the time from the SNTP server Daylight Saving Enable or disable daylight saving time function When daylight Time saving time is enabling you need to configure the daylight saving time period UTC Time zone Set the switch location time zone The
25. pid Spanning tree protocol IEEE 802 1AB LLDP CA Fiber Ports 100 Base FX SC Connector Multi Mode O to 2 km 1310 nm 50 125 um to 62 5 125 um Single Mode O to 30 km 1310 nm 9 125 um ORing Industrial Networking Corp 40 IPS 2000 Series User s Manual LED Indicators Per Unit Power Green Red RJ45 Ports Per Port Link Activity Green Blinking Green Ring Port Amber Power Input Voltage PWR1 2 12 to 48VDC in 7 pin Terminal Block Reverse Polarity Protection Environmental Wide Operating Temperature Operating Humidity 5 to 95 non condensing Dimensions W x D x H 52 mm W x 106 mm D x 144 mm H Casing IP 30 protection Regulatory Approvals Regulatory Approvals FCC Part 15 CISPER EN55022 class A EMS EN61000 4 2 ESD EN61000 4 3 RS EN61000 4 4 EFT EN61000 4 5 Surge EN61000 4 6 CS ORing Industrial 41 Networking Corp
26. rol Port 01 100TX Down Enable N A N A ort O2 100TX Down Enable N A N A Port 03 100TX UP Enable 100 Full Disable Port D4 100T Down Enable N A N A OS 100TX Down Enable N A N A EDS 100TX Down Enable N A N A Port Status interface 5 1 4 Redundancy 5 1 4 1 Fast Recovery Mode The Fast Recovery Mode can be set to connect multiple ports to one or more switches The IPS 2042 series with its fast recovery mode will provide redundant links Fast Recovery mode supports 4 priorities only the first priority will be the act port the other ports configured with other priority will be the backup ports Fast Recovery Mode Mot included rs Not included Fast Recovery Mode interface ORing Industrial Networking Corp 24 IPS 2000 Series User s Manual The following table describes the labels in this screen Label Description Activate the fast recovery mode Port can be configured as 5 priorities Only the port with highest priority will be the active port 1 Priority is the highest Click Apply to set the configurations 5 1 4 2 O Ring O Ring is the most powerful ring in the world The recovery time of O Ring is less than 10 mS lt can reduce unexpected damage caused by network topology change O Ring Supports 3 Ring topology O Ring Coupling Ring and Dual Homing O Ring Coupling Ring Man i Hag prady 1 E a i4 mr 5 Ring Master Disable v Coupling Port Fort 03 Hom
27. thods that supported by the system Check the corresponding box to enable system event warning method you wish to choose Please note that the checkbox can not be checked when SYSLOG or SMTP is disabled System Warning Event Selection system Event Disable Disable e Disable Disable e Disable Disable we Disable Disable we Disable Disable we Disable System Warning Event Selection interface The following table describes the labels in this screen System Cold Start Alert when system restart O Ring Topology Alert when O Ring topology change Change Port Event Disable Link Up Link Down Link Up amp Link Down Apply Click Apply to set the configurations ORing Industrial Networking Corp 36 IPS 2000 Series User s Manual 5 1 9 Front Panel Show IPS 2000 series panel Click Close to close panel on web 10100M 5 1 10 Save Configuration If any configuration changed Save Configuration should be clicked to save current configuration data into the permanent flash memory Otherwise the current configuration will be lost when power off or system reset save Configuration System Configuration interface The following table describes the labels in this screen tabel Description Save Save all configurations Show help file ORing Industrial 37 Networking Corp 5 1 11 LLDP LLDP Link Layer Discovery Protocol function allows the switch to advertise its infor

User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents