caution - Sonic Alert
Contents
1. ra Sonic Alert America s Leader in Visual Alerting Systems Sonic Boom Alarm Clock amp Bed Shaker Model SBJ525SS v3 OPERATION INSTRUCTIONS MPORTANT Please read these instructions carefully before use and retain for future reference See operating instructions on back Use only the supplied or recomended Sonic Alert adaptor to connect the unit Warning To prevent fire or shock hazard do not expose this appliance to rain or moisture Before connecting to mains power make sure that the requirements specified on the apparatus corresponds to the available power UPPI in that country i e AC100 240V 56 60 Hz The ventilation should not be impeded by covering the ventilation openings with items such as newspaper table cloth curtains etc No naked flame sources such as lighted candles should be placed on the apparatus It shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus Do not place the product in closed bookcases or racks without proper ventilation Where the mains power plug is used as the disconnect device the disconnect device shall remain readily operable INSTRUCTIONS fc ad Features show on diagram above 1 DC adpator input 9 Minute 2 Tone 10 Alarm Set Off 3 Alarm indicator 11 Function Switch 4 PM indicator 12 Volume Knob 5 Flashing LED 13 Vibrator out Jack 6 Time Set 14 Bat2. was supplied with your handled device to the USB charging port 15 on the back panel of this alarm clock Observe the charging indicator on your device to confirm that it is charging Note Charging time will vary depending on the charging current that your device requires Therefore some devices will take longer to charge than others Battery Backup To use the battery backup you can install 2 pieces of AA size UM 03 alkaline battery in the back of the clock located under the battery cover 14 Please note the LED display will not show during power failure but the clock will still be running and keeping proper time until the power is restored NOTE For the best results it is recommended that the battery be changed every 6 8 months If the clock is not used for a while it is recommended to remove the battery to aviod leakage DC 5V Power Input Attach the DC power supply input to the back of clock labeled DC5V IN 1 Important do not confuse DC input with vibrator input GENERAL DATA UL listed Power Adaptor AC100 240V 50 60Hz Power Consumption Adaptor Output DC5V 800mA USB Charging Port Rating 5 00mA CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE THE COVER OR BACK FROM THE PRODUCT NO USER 1Pe exclamation mark SERVICEABLE PARTS within the triangle isa INSIDE REFER warning sign alerting you SERVICING TO YOUR of important instructions SONIC ALERT DEALER 2 CO Panying the produ
3. ct The Lightening flash and arrowhead within the triangle is a warning sign alerting you of dangerous voltage inside the product WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE The normal function of the product may be disturbed by Strong Electro Magnetic Interference If so simply reset the product to resume normal operation by following the instruction manual In case the function could not resume please use the product in other location Attention should be drawn to the environmental aspects of battery disposal om this indicating separate collection for electrical and electroinc equipment SONIC ALERT S 1 YEAR LIMITED WARRANTY The Sonic Boom Alarm Clock Model SBB500ss is warranted against manufacturing defects in materials and workmanship for one 1 year from the date of purchase Within this period Sonic Alert will repair or replace at our option the SBB500ss without charge for parts and labor Simply contact our customer service department to obtain an RA return authorization number and instructions on how to process your product for return Call 1 888 864 2446 or e mail to RMA sonicalert info You ll need a copy of your receipt to process the return authorization Sonic Alert Inc Troy MI 48083 USA Sonic Alert Made in China Sonic Alert Troy MI 48083 www SonicAlert com 1 888 864 2446
4. he time is PM For AM time indication the dot does not light up Setting the alarm time 1 Press and hold the Alarm Set Button 10 at the same time press the Hour Button 7 to advance the alarm display rapidly until the hour is correct 2 Press and hold the Alarm Set Button 10 at the same time press the Minute Button 9 to advance the alarm display rapidly until the minute is correct 3 Make sure the alarm time is correctly set for AM or PM the lighted dot 4 indicated PM Please be sure to release the HOUR and MIN set buttons before releasing the ALARM button Selecting 12 or 24 hours format Press and hold the Hour button 9 for 6 seconds to enter the hour selection mode release the Hour button 9 when the display shows 12 H or 24 H Press and release the hour button to toggle between 12 or 24 hours If no selection is made within 4 seconds then the last displayed hour format will be chosen and the display will return to the normal Time mode Waking to Alarm 1 Set Function Switch 11 to choose VIB BUZZ or VIB BUZZ 2 Set desired volume using the Volume knob 12 for buzzsound 3 Set alarm wake time per instructions for setting alarm time above Adjusting The Alarm Duration Time The default alarm duration time setting is 30 minutes you may adjust the alarm duration between 1 minute and 59 minutes as desired To adjust the alarm duration e Press and hold the AL SET button 5 for si
5. ooze button e Press the MIN button 10 to adjust the snooze time to the desired setting from 1 minute to 30 minutes e When the display is showing the desired snooze time it will return to the normal clock mode after 3 seconds The new snooze time setting becomes the new default and remains in the memory until you change it again Volume To adjust the volume rotate the Volume wheel 12 until you have reach the desired level Tone Adjust the tone by rotating the Tone wheel 2 until you have reach the desired level Dimmer Operation There is a 5 level brightness control for the LED display Press the SNOOZE button 8 once to change the display brightness The brightness will cycle from 5 4 3 2 1 2 3 4 5 from bright to dim then from dim to bright NOTE The dimmer function will not work when the clock is in snooze mode Bed Shaker Vibrator Figure B 1 Attach the bed shaker jack to the back of the clock at VIBRATOR input 13 2 To select vibrator slide Function Switch 11 to VIB or VIB BUZZ position 3 Place vibrator under mattress or pillow USB Charging This alarm clock is equipped with a convenient USB charging port on the back panel that allows you to recharge many brands of mobile phones portable music players and other handheld devices that are supplied with USB charging cables The output rating of the USB charging port is 500mA To charge your device connect the USB charging cable that
6. tery Compartment door 7 Hour 15 USB Charging Port 8 Snooze Dimmer Test Mode 1 Press and hold the Snooze and Time buttons for 3 seconds to enter the Test Mode The display will show 7ES7 to indicate it is in TEST Mode 2 If within 1 minute no button is pressed then it will exit the Test Mode and return back to the Time Mode 3 Press any button within 1 minute except the Snooze amp Time buttons which has no effect it will exit the Test Mode immediately 4 While in Test Mode sliding the Function Switch will demonstrate the different functions of the clock a Function Switch at OFF it will have a continuous Vee sound to indicate it is in the Test Mode b Function Switch at BUZZ it will demonstrate the buzzer sound c Function Switch at VIB it will demonstrate the vibrator d Function Switch at VIB amp BUZZ it will demonstrate the buzzer sound amp the vibrator 5 After finish with the Test Mode press any button except the Snooze amp Time buttons which has no effect it will exit the Test Mode immediately Setting the correct time 1 2 Press and hold the Time Set Button 6 at the same time press the Hour Button 7 to advance the clock display rapidly until the hour is correct Press and hold the Time Set Button 6 at the same time press the Minute Button 9 to advance the clock display rapidly until the minute is correct A lighted dot 4 in the upper left of the clock display indicated t
7. x seconds The clock display will show the default alarm duration as 30 release the AL SET button e Press the MIN button 10 to adjust the alarm duration to the desired setting from 1 minute to 59 minutes e When the display is showing the desired alarm duration time it will return to the normal clock mode after 3 seconds The new alarm duration time setting becomes the new default and remains in the memory until you change it again Shutting Off Alarm Alarm can be shut off temporarily for the day or shut off permantently 1 When the alarm goes off simply press the AL off button 10 the alarm will shut itself off for the day and come back on the next day at the same time if the alarm setting has not changed 2 To shut off the alarm permanently slide Function Switch 11 to of positon Alarm will not come on until Function Switch 11 is set to VIB or BUZZ or VIB BUZZ position Snooze Operation SNOOZE button 8 press after alarm has sounded The alarm will be turned off for 9 minutes for extra sleep The alarm will come back again after 9 minutes You may repeat many time up to 119 minutes Adjusting The Snooze Time The default snooze time setting is 9 minutes but you may adjust the snooze time between 1 minute and 30 minutes as desired To adjust the snooze time e Press and hold the SNOOZE button 3 for four seconds The clock display will show the default snooze time 9 Release the Sn
Download Pdf Manuals
Related Search