PICQUICK User`s Manual
Contents
1. programming e g may be used as inputs Fig 1 I CSP connection to application Application PCB VDD PIC16F8X ICSP Connector OOA wh To application circuit solation circuits The part to be programmed connects to CSP connector of the programmer using a cable according to following chart Pin Number Signal Name ICSP Connector 1 MCLR VPP 2 unused key 3 VCC VCC 4 GND GND 5 RB7 DATA 6 RB6 CLK Further it must be ensured that there is log 0 on the Low Voltage Programming pin Placement of this pin for particular device Device LVP pin PIC16F62x RB4 PIC16F87x RB3 PIC18Fxxx RB5 Blocking capacitor between VCC and GND should not exceed 100 uF Power consumption of application circuitry connected to VCC should not exceed 10 mA during the programming MCLR pin must not be connected directly to VCC it may be connected through resistor of 10 kQ the application circuitry must be tolerant to 13 V supplied to MCLR More information is available in the help of the UP software Further information 1 http www pic tools com 2 http www microchip com Contact Address ASIX s r o Staropramenna 4 150 00 Prague Czech Republic Tel 420 257 312 378 Fax 420 257 329 116 E Mail info pic tools com support pic tools com sales pic tools com WWW www pic tools com PICQ_MANEN All rights reserved Copyright 1991 2004 ASIX s r o2. up to 40 pins except PIC14000 can be programmed directly When inserting part to be programmed into ZIF socket pin 1 of the part must always match pin 1 of the socket pin 1 of the socket is located by the socket lever PIC14000 in DIP package and all parts in non DIP packages may be programmed using an adaptor Appropriate adaptor is to be inserted to the programmer with its pin 1 matching pin 1 of the ZIF socket Do not handle the part when it is being programmed or read Operation in progress is indicated by yellow LED The programmer is equipped with overcurrent protection If the current from power supply or programming voltage source exceeds 100 mA the part is disconnected in a few microseconds This feature significantly decreases probability of possible damage to the part when handled incorrectly e g wrong part is selected or the part is inserted incorrectly Please note that in ICSP mode is this overcurrent protection limited ICSP programming Using ICSP In Circuit Serial Programming it is possible to program the part directly in the target circuitry The application must meet following conditions see fig 1 1 MCLR VPP pin of the microcontroller must be isolated from reset circuitry e g by a resistor During the programming 13 V is applied to this pin and rising edge of this signal must not be affected by the application circuitry 2 RB6 and RB7 pins must be disconnected from the application circuitry during the
3. All trademarks used in this document are properties of their respective owners This information is provided in the hope that it will be useful but without any warranty We disclaim any liability for the accuracy of this information We are not responsible for the contents of web pages referenced by this document
4. PI CQUI CK Development programmer for Microchip PIC microcontrollers and Microchip serial EEPROM memories User s Manual AMX PI CQUI CK PICQUICK is a device designated for programming of PIC microcontrollers and serial EEPROM memories manufactured by Microchip Software for 95 98 ME 2K XP is available Recent list of supported parts and possible changes to this manual can be found at www pic tools com Technical specification Connects to PC using standard parallel port LPT Dimensions 80 x 160 x 18 mm Operation temperature range 5 to 50 C Operation relative humidity max 90 Package contents Programmer module In Circuit Serial Programming ICSP cable Programmer to PC cable Installation CD ROM with software and documentation Quick start guide Hardware installation Turn off the computer Connect the SubD 25 connector to its parallel port Connect SubD 9 connector to the programmer Connect the power supply Power is indicated by a green LED Turn the computer back on Software installation Insert the installation CD ROM ASIX If the inital screen is not displayed automatically open Index htm Or ReadMeFirst rtf file located in the CD ROM root directory manually and follow the instructions New updates are available for free at www pic tools com Hardware operation Turn off both the computer and programmer any time you are about to connect or disconnect the programmer All parts in DIP package with
Download Pdf Manuals
Related Search