AquaTRAM LT Pool Lift User`s Manual
Contents
1. FIGURE 12 AOUATRAM LT IN FULLY UPRIGHT POSITION C SX PRESS AND HOLD THE MOVE DOWN BUTTON FIGURE 13 NOTE CHECK ALL NUTS amp BOLTS FOR TIGHTNESS AND FOR WORN PARTS BEFORE EACH USE NEVER OPERATE THE LIFT WITH THE ARMRESTS FLIPPED UP LOADING FROM A WHEELCHAIR The AQUATRAM LT Pool Lift should always be in the fully upright position when transferring into the chair Before transferring check to make sure the lift is operating by making a short test run move the chair at least part way in and out of the pool The armrest on either side will flip up to allow for easier lateral transfers Transfer into the chair and then lower the flip up armrest back into its normal position Secure the adjustable lap belt around the waist so that the belt is snug but not uncomfortably tight OPERATING THE AQUATRAM LT POOL LIFT The HANDSET CONTROL is used to raise and lower the lift during operation To lower the chair into the pool press and hold the V MOVE DOWN button see diagram to the left The lift will move DOWN towards the water as long as the V MOVE DOWN button is pressed To stop moving simply release the button To MOVE UP back to the fully upright position press and hold the A MOVE UP button Again the lift will move only as long as the button is pressed and held When you are sufficiently submerged into the water release the V MOVE DOWN button Now remove the lap belt by grasping the en2. ANCHO POOL DEPTH CORE DRILLING RETRO FIT INSTRUCTIONS Required Materials amp Tools Core drill and 1 MA core drill bit Tape Measure Marking Pen suitable for writing on concrete Hammer Cold Chisel Torpedo Level High Strength 2 part construction epoxy Black electrical tape Optional Masking tape lu Pentair recommends either Hilti Brand HIT HY 150 or Simpson brand ET22 Strong Tie or equivalent 1 Locate the anchor plate four 4 anchor inserts with nuts and mounting hardware Sold separatelyP N 11231 See picture 2 Using the larger holes in the anchor plate as a template mark the four hole locations with a marking pen on the pool deck Verify that the CENTER LINE of the front anchors are no more than 14 inches from the pools edge See FIGURE 1 page 6 3 Using the core drill and the 1 1 4 core drill bit drill out the four hole locations marked on the pool deck to a depth of about 4 72 a NOTE You can use black electrical tape on the end of the drill bit as a visual marker to indicate the proper depth that you need to drill to FIGURE 2 b NOTE Depending on your local grounding requirements 1 2 X 1 172 HEX BOLT you may need to arill one hole larger than the others so that ANCHOR you can ground at least one of the anchor inserts In some cases saw cutting a portion of the deck out completely might be required In this case follow the Saw Cutting Retro
3. FIGURE 7 2 Install the AquaTRAM LT pool lift onto the four 4 anchors using 1 2 x 1 1 2 stainless steel hex head bolts and 1 2 stainless steel flat washers Make sure all bolts are tight before using the lift FIGURE 9 3 Plug the handset cable into the large handset socket on the bottom of the control box Be sure you press the cord end firmly into the socket until you are sure it is all of the way into the socket Failure to fully push the remote cord into the socket may result in faulty or interrupted operation FIG 8 HOOKS LOOPS FACING EACH OTHER LOOP EACH SEATBELT HALF THROUGH EYE PINCH LOOP ENDS 4 Before installing the battery put it on the charging unit and let it charge for 24 hours Make sure the orange charge light illuminates when the battery is being charged 5 Remove the fully charged battery from the charger and install it on top of the Control Box as shown in FIGURE 9 The battery will line up square with the control box and will click when it locks in place properly The lift will only operate when the battery is mounted properly WHEN LIFT IS NOT IN USE STORE THE BATTERY ON THE CHARGER DO NOT LEAVE THE BATTERY ON THE LIFT WHEN NOT IN USE FIGURE 8 FIGURE 9 a G PLUGS ARE FULLY SEATED AS SHOWN HEX HEAD BOLT 4 19 FLAT WASHER 4 FLUSH W DECK HANDSET CABLE HINT APPLY ANTI SIEZE LUBE INCLUDED TO 12 BOLTS BEFORE INSTALLING TO HELP PREVEN
4. barring any unforeseen delays the place of purchase will be notified of Pentair s decision regarding the claim If requested by Pentair any Lift or component part thereof must be returned freight prepaid to Pentair s designated factory location or duly appointed distributor for inspection and or repair or replacement Pentair will at its option refund the purchase price or repair or replace the Lift or component part thereof and deliver the repaired Lift or component part thereof or replacement to the buyer of the Lift freight prepaid to the destination provided for in the original order Lift or component part thereof returned to Pentair for which Pentair provides replacement under this limited warranty shall become the property of Pentair A new warranty period shall NOT be established for the repaired or replaced Lift or component part thereof Such Lift or component part thereof shall remain under warranty only for the remainder of the original warranty period on the original Lift purchased This written limited warranty constitutes the final complete and exclusive statement of warranty terms No person or organization 1s authorized to make any other specific or implied warranties or representations on behalf of Pentair THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED WHICH ARE HEREBY DISCLAIMED AND EXCLUDED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTIC
5. no damage occurred in transit and that a damaged part is not used If any damage occurred in transit Pentair Water Commercial Pool and Aquatics Pentair must be notified within three days of receipt of unit Proper installation cannot be overstressed as an improper installation voids Pentair s warranty and may affect the safety of the user N WARNING IMPORTANT SAFETY INSTRUCTIONS 1 READ AND FOLLOW ALL INSTRUCTIONS LIFT SAFETY CAN ONLY BE ENSURED IF THE LIFT IS INSTALLED AND OPERATED PROPERLY ACCORDING TO THESE INSTRUCTIONS 2 WARNING TO REDUCE RISK OF INJURY DO NOT PERMIT CHILDREN TO USE OR OPERATE THIS PRODUCT 3 WARNING DO NOT PERMIT CHILDREN TO PLAY ON THIS PRODUCT 4 WARNING NEVER APPLY DIRECT WATER PRESSURE TO ELECTRONIC COMPONENTS 5 DO NOT USE THE AQUATRAM LT LIFT FOR WATER DRAFTS OVER 9 DECK TO WATERLINE 6 NEVER OPERATE THIS LIFT UNDER LOAD WITH NO WATER DRY POOL 7 SAVE A COPY OF THESE INSTRUCTIONS WARNING MAKE SURE THE AREA AROUND THE LIFT IS CLEAR BEFORE OPERATING NEVER OPERATE THE LIFT WITH ANY PERSON WITHIN THE OPERATING RANGE OF THE LIFT INCLUDING ON THE DECK OR IN THE WATER NEVER MOVE THE LIFT DOWN WHILE OVER THE DECK IF THE LIFT COMES INTO CONTACT WITH THE DECK OR A WALL RELEASE THE BUTTON IMMEDIATELY OR PRESS THE EMERGENCY STOP BUTTON DO NOT ALLOW CHILDREN TO OPERATE THE LIFT WITHOUT SUPERVISION CHECK ALL NUTS AND BOLTS FOR TIGHTNESS AND FOR WORN PARTS BEFORE EACH US
6. the four holes drilled in the deck Using a torpedo level on the plate verify that you can level up the anchor system If they do not line up you may have to enlarge your holes After verifying that the anchor inserts line up with the holes properly and you can level the anchor assembly remove the anchor assembly and fill each hole in the pool deck at least half full of two part construction epoxy not included Pentair recommends either Hilti Brand HIT HY 150 or Simpson M brand ET22 Strong Tie or equivalent Pick up the anchor assembly with the four 4 anchor inserts attached to the underside and carefully place them into the four holes drilled in the deck As you place the anchor inserts that are attached to the anchor plate wiggle the anchor system a little to make sure the epoxy gets on all sides of the anchor inserts Once the anchor inserts are placed into the holes use a small torpedo level on the anchor plate to make sure you are level and plumb Allow the epoxy to set up according to the manufacturers recommendations and remove the hardware and the anchor plate You can now safely mount the lift to the anchor system using the same hardware you used to mount the anchor inserts to the underside of the anchor plate The anchor plate can be recycled or used for installing a second set of anchors in another location att TO 14 _ CORE DRILL 1 1 4 4 1 2 4 PLACES POOL WALL 36 OR FURTHEST MIN OBSTRUCTION
7. the open area of the deck Tie the rebar into the existing deck if possible 8 Setthe anchor system in place making sure that the center line of the front anchor inserts are no more than 14 inches away from the pools edge SIDE VIEW 9 Using the string line or a straight edge make sure the top of each anchor body is level and flush with the FINISHED deck FIGURE surface Each anchor body can be adjusted individually by T turning the nuts with a large wrench OM MAE _ j 10 Ground the anchor system using the grounding lug on the LABEL ON TO FRONT EDGE anchor plate according to your local code requirements 11 Pour your concrete and finish the pool deck surface 12 Once the concrete has cured install the lift by aligning the holes in the lifts base with the anchors installed in the deck Secure the lift to the deck using the stainless steel hardware that comes with it See drawing below a NOTE Use Anti Seize on the hardware to prevent the hardware from seizing in the anchor inserts DECK TO CENTER OF ANCHOR 4 14 MAX FLUSH WITH DECK 10 2 cm ANCHOR INSTALLATION NEW CONSTRUCTION For installations where a new deck is being poured or where a dedicated pad is being poured just for the pool lift the concrete must satisfy the requirements outlined on page 6 For convenience here are the requirements again YOUR POOL DECK MUST BE AT LEAST 3 FEET LONG BY 3 FEET WIDE BY 6
8. E AquaTRAM LT Technical Support Contact Technical Support at Sanford North Carolina 8 A M to 5 P M Phone 800 831 7133 Fax 919 566 8920 Web sites visit www pentaircommercial com AQUATRAM LT POOL LIFT TABLE OF CONTENTS PAGE DESCRIPTION 5 PACKING LIST 6 SITE AND POOL DECK REQUIREMENTS 7 8 CORE DRILL RETROFIT INSTRUCTIONS 9 SAW CUT RETROFIT INSTRUCTIONS 10 NEW CONSTRUCTION INSTRUCTIONS 11 AQUATRAM LT LIFT ASSEMBLY INSTRUCTIONS 12 24V BATTERY OP amp INSTALL INSTRUCTIONS 13 BATTERY MAINTENANCE 14 AQUATRAM LT LIFT OPERATING INSTRUCTIONS 15 16 SAFETY amp CARE FOR YOUR LIFT 17 19 TROUBLESHOOTING GUIDE 20 AQUATRAM LT PARTS LIST 21 SEAT ASSEMBLY PARTS LIST 22 OPTIONS 23 WARRANTY THE AQUATRAM LT POOL LIFT AQUATRAM LT POOL LIFT W FOOTREST P N 11230 24V BATTERY P N 11211 BATTERY CHARGER W MOUNTING PLATE P N 11277 SAFETY BELT P N 11215 NOTE The AquaTRAM LT pool lift requires a concrete anchor system P N 11231 SITE amp POOL DECK REQUIREMENTS This lift is designed for commercial or residential use on in ground pools and spas This lift is not designed to clear a wall or obstacle The lift should be installed on the pool deck where a Straight linear section of the pool wall is at least six 6 feet long The lift should be installed at a pool depth pool deck to pool floor of no less than 42 but not more than 48 inches If the edge of the pool deck curves the ancho
9. Fit Instructions USE SMALLER TN 4 Remove the core from the holes using a hammer and chisel The holes should be completely dry and clear of any debris before installing the anchors into them 5 Remove the nuts from the threaded anchor inserts and the black protective cover from the end of the anchor insert exposing the internal threads that will accept the mounting hardware 6 Using the smaller holes in the anchor plate thread the mounting hardware through the anchor plate holes and into the ends of the four anchor inserts so that the tops of the inserts are flush with the BOTTOM of the plate see diagram on left IMPORTANT Use the enclosed packet of anti seize on the threads of the hardware to prevent the hardware from seizing in the anchor inserts a NOTE It is recommended that you apply tape to the bottom of the anchor plate around the holes so that when and if the two part epoxy oozes out of the holes that it does not secure the anchor plate to the pool deck 10 11 12 FIGURE 3 Allow for a way to ground at least one of the anchor inserts according to your local code requirements Before putting epoxy into the holes and setting the anchor inserts you will want to test fit the anchor inserts in the pre drilled holes first to make sure they line up properly You can do this by picking up the anchor plate with the four 4 anchor inserts attached to the underside and carefully place them into
10. INCHES THICK IT MUST BE REINFORCED WITH 4 REBAR ON 10 INCH CENTERS IN BOTH DIRECTIONS Obviously you may make the deck larger than this which is almost always the case when putting in a deck that surrounds the pool Note that the entire deck does not need to be 6 thick but that the area around the installed lift 3 by 3 should be 6 thick at a minimum The rest of the deck may be thinner 4 is typical as long as it is 6 thick around the lift The entire deck should be reinforced with 4 rebar on 10 centers in both directions which is also common for this type of structure Our minimum requirement is that the 3 by 3 section be reinforced accordingly but it is good practice to extend the rebar grid over the entire deck Commonly the rebar grid is used for grounding bonding also Grounding of the lift can usually be accomplished with a length of bare solid copper wire 14 or 16GA wrapped tightly around a piece of the rebar and then connected to the grounding lug on the anchor plate Note that this is only effective when the rebar grid itself has been grounded CHECK YOUR LOCAL ELECTRICAL CODE GROUNDING REQUIREMENTS FOR POOL EQUIPMENT ALWAYS GROUND THE UNIT PER LOCAL ELECTRICAL CODES FIGURE 6 ORIENTATION LABEL 35 6 cm REBAR 14 MAX GROUNDED TO CENTER OF ANCHOR ADJ HEIGHT UNTIL FLUSH WITH DECK AQUATRAM LT POOL LIFT ASSEMBLY INSTRUCTIONS 1 Attach seat belt as shown in FIGURE 7
11. Pentair Water Commercial Pool and Aquatics AQUATRAM LT POOL LIFT USER MANUAL IMPORTANT SAFETY INSTRUCTIONS 1 WARNING TO REDUCE RISK OF INJURY DO NOT PERMIT CHILDREN TO PLAY ON THIS PRODUCT 2 WARNING DO NOT PERMIT CHILDREN TO OPERATE OR USE THIS PRODUCT 3 SAVE A COPY OF THESE INSTRUCTIONS 2011 Pentair Water Pool and Spa Inc All rights reserved 1620 Hawkins Ave Sanford NC 27330 919 566 8000 10951 West Los Angeles Ave Moorpark CA 93021 805 553 5000 AquaTRAM and Pentair Water Commercial Pool and Spa are trademarks and or registered trademarks of Pentair Water Pool and Spa Inc and or its affiliated companies in the United States and or other countries Unless noted names and brands of others that may be used in this document are not used to indicate an affiliation or endorsement between the proprietors of these names and brands and Pentair Water Pool and Spa Inc Those names and brands may be the trademarks or registered trademarks of those parties or others P N 11239 Rev A 04 18 11 AQUATRAM LT POOL LIFT 300 LB 136 kg MAXIMUM CAPACITY MANDATORY LEAVE THIS MANUAL WITH LIFT OWNER READ CAREFULLY Check entire box and inside all packing materials for parts Before beginning assembly read the instructions and identify parts using the figures and parts listed in this document It is critical that all parts be carefully inspected by the installer prior to installation to ensure that
12. T THREAD DAMAGE CABLES 10 24 VOLT BATTERY SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS FIGURE 10 CONTROL BOX 24V BATTERY CHARGER BRACKET The AQUATRAM LT Pool Lift comes with a 24v sealed rechargeable battery wall mount charging unit with mounting bracket control box and a waterproof handset controller The control box is mounted to the AQUATRAM LT Pool Lift and has a plug in socket for both the actuator and the handheld controller The battery mounts directly above the control box with a quick release clip To operate the AQUATRAM LT Pool Lift plug in the handset controller to the control box and push the corresponding button to either lower or raise the unit The lift should be able to complete approximately 10 20 full cycles before the low battery indicator tone will sound The low battery tone indicates that there is approximately 20 battery life remaining At this point DO NOT ATTEMPT TO OPERATE THE LIFT remove the battery from the unit and recharge on the wall mounted charging unit To recharge the battery simply grip the top of the battery and depress the clip on the back of the battery This will unclip the battery from the control box bracket and the battery can then be clipped into the wall mount charger When the charger is plugged in the green ON light will illuminate When the battery is correctly mounted to the charger the orange CHARGE light will illuminate When the battery is fully charged th
13. ULAR PURPOSE OR USE THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO THE LIFT OR COMPONENT PART THEREOFSHALL BE LIMITED TO REPAIR OR REPLACEMENT AT PENTAIR S DESIGNATED FACTORY LOCATION OR DULY APPOINTED DISTRIBUTOR OR SUCH OTHER PLACE AT PENTAIR S SOLE OPTION IN NO EVENT SHALL PENTAIR S LIABILITY EXCEED THE ENTIRE AMOUNT PAID TO PENTAIR BY THE ORIGINAL PURCHASER FOR THE LIFT OR COMPONENT PART THEREOF IN NO EVENT SHALL PENTAIR BE LIABLE FOR ANY INCIDENTAL CONSEQUENTIAL SPECIAL INDIRECT PUNITIVE OR EXEMPLARY DAMAGES OR LOST PROFITS FROM ANY BREACH OF THIS LIMITED WARRANTY OR OTHERWISE Pentair Water Commercial Pool and Aquatics A Division of Pentair Water Pool and Spa Inc 1620 Hawkins Ave Sanford NC 27330 1351 Route 55 LaGrangeville NY 12540 22 PENTAIR WATER POOL AND SPA INC 1620 Hawkins Ave Sanford NC 27330 10951 W Los Angeles Ave Moorpark CA 93021 Phone 800 831 7133 Fax 800 284 4151 P N 11239 RevA 23
14. USE ANCHOR PLATE LARGER HOLES TO MARK HOLE LOCATIONS ser ALSO USE ANCHOR PLATE FOR TEST FITTING AND TO HOLD IN PLACE A5 SAW CUTTING RETRO FIT INSTRUCTIONS Required Materials amp Tools Concrete saw with Diamond blade u Tape Measure 4 long Straight edge or chalk line Sledge Hammer Cold Chisel Torpedo Level Sting line Concrete Concrete tools 4 Rebar 1 Locate the anchor plate four 4 anchor inserts with nuts and FIGURE 4 mounting hardware Sold separately from lift P N 11231 1 4 X 1 2 HEX BOLT See picture ANCHOR me 2 Mark out a section of the pool deck that you are removing INSERT 4 LUG using a chalk line or straight edge and a marker You should LARGER plan on removing at least a Three foot by three foot section HOLES 3 Using the saw with the diamond blade make your cuts along NUT Y t the lines that you marked y n e 4 Using the sledge hammer break up the concrete within the ANCHOR PLATE area that you cut and remove the pieces 5 After you have removed the portion of the deck verify that your new deck will be able to be at least 6 inches deep 6 Remove ONE of the nuts from each of the anchor inserts and place the anchor inserts through the larger holes in the anchor plate Thread the nut back on the other side of the anchor insert so that the anchor plate is sandwiched between the nuts See diagram on left 7 Install rebar in
15. all the battery on top of the control box Make sure you hear a click which indicates that the battery is correctly seated The lift will not work if the battery is not seated correctly Silver tabs are the contact terminal points 17 If the lift stops moving over the water and is stuck 4 Then try pushing the emergency button A If the lift gets stuck out over the water use a pen or pencil tip and stick it into the emergency button on the front of the control box to retract the lift Note the lift will not retract if the battery is not fully charged or if the control box is not working The emergency button only overrides the remote in case it has gone bad If this does not retract the lift then chances are the remote is fine and you either have a problem with the battery the control box or the cords are damaged or not plugged in properly Use a pen or pencil tip to push in the small black circle located next to the word emergency on the front of the control box USING THE EMERGENCY BUTTON on the AquaTRAM W LT Pool Lift Control Box gt CEENNUN A ee On the front side of the control box is a small recessed button marked emergency Take a pen or pencil or other pointed object and depress the emergency button This will bypass the remote control and send a signal directly to the actuator to raise the seat out of the pool and back to the deck or up position NOTE This function will only work i
16. bracket is silver clip which will not allow behind the silver clip Not allowing for an electrical connection movement 16 If the battery is fully charged and the lift is not moving then 2 Check all cords A Check that the cords are properly plugged in Start by unplugging the remote and the actuator cord from the control box Once these cords are removed check the ends for corrosion or damage Plug the remote cord back in by lining up the raised tab on the plug to the grooved line on the control box outlet Note that these cords require some force to plug them in fully You will know they a correctly inserted when you here a popping sound The cords will be recessed into the outlet If they are flush with the outside of the outlet they are not plugged in fully and the lift will not function Make sure you do this for both cords NOT inserted fully Fully inserted If you have checked all the cords and the lift still doesn t move 3 Check the contact points A After you have fully charged the battery and checked the cords to make sure they are properly plugged in check to make sure the contact points are not corroded or bent If the contact points are corroded take some rubbing alcohol and a q tip and clean off the points After cleaning the contact points it is recommended to put some dielectric grease on the contact points terminals to help ensure good electrical contact and prevent corrosion Then reinst
17. briskly Afterwards be sure to wash and rinse the lift again with soap and water When storing the lift make sure it is in a dry area and covered DO NOT STORE in or around pool chemicals 15 TROUBLESHOOTING GUIDE Before troubleshooting make sure the battery is fully charged If the lift doesn t move when the handset button is pressed When you can t get the lift to move check the following things 1 Make sure the battery is fully charged A Before charging the battery first make sure the green light on the front of the charger is illuminated this means that the charger is on Then check to make sure the silver contact points on the battery and charger are not damaged or corroded and that they are clean Then place the battery on the charger and look for the orange charge light to illuminate on the front of the charger When the orange light goes off the battery is fully charged The top green light will always be illuminated indicating that it has power When charging the battery the bottom orange light will illuminate until fully charged C When the battery is correctly installed on the charger or control box you should hear a click indicating the battery is properly seated on the unit Also note that when the battery is properly seated there should not be any gaps between the battery and the control box charger Not attached properly Note Properly Attached the white bracket is in front of Note that the white
18. d crevices Do not use a bristled brush or steel wool to clean the lift Check that the lift is working properly and then place the battery on the charger It is recommended that the battery be charged after every day of use If the lift is used WEEKLY follow the same steps as above Also be sure to check all of the contact points terminals for damage or corrosion If you notice corrosion gently clean the terminals To clean corrosion from the terminals use a Q tip and some rubbing alcohol If the corrosion is particularly stubborn try using a 3M scotch brite pad but be careful not to damage the terminals Apply dielectric grease to the terminals after cleaning them This will help to prevent further corrosion Do not leave the battery on the lift Always store the battery on the charger whenever the lift is not being used 14 If the lift is used MONTHLY follow the same steps as above Also check the nuts and bolts to make sure they are securely fastened this is always a good idea no matter how often or infrequently the lift is used Also make sure to store the battery on the charger and not on the lift Leaving the battery on the lift for extended periods will significantly shorten the battery s lifespan If the lift is being STORED for an extended period of time follow all of the steps above Check for rusting at all crevice and weld points If you notice rusting soray some WD 40 on the affected area and take a 3M scotch brite pad and rub
19. d of the belt that is protruding above the lap belt and tugging gently To create more room in front of the chair the footrest may be flipped inwards under the chair Exit the chair by sliding straight forward until you are clear of the seat and the footrest When you are ready to return to the lift make sure that the chair is lowered submerged sufficiently to allow you to easily slide into the chair Next re secure the adjustable lap belt snugly around your waist Raise the chair out of the pool by pressing and holding the A MOVE UP button until the lift is once again fully upright 13 SAFETY amp MAINTENANCE INSTRUCTIONS DO NOT PLAY ON OR AROUND THIS LIFT Check the AquaTRAM Series Pool Lifts before each use to assure there are worn parts and that all hardware is properly tightened If there are any worn parts replace them BEFORE using the AquaTRAM Series Pool Lifts You can call our customer service at 1 888 687 3552 to order any parts Pentair Water Commercial Pool and Aquatics lifts shall be grounded per local codes Atleast ONCE A WEEK the AquaTRAM Series Pool Lifts must be cleaned with fresh water Do not spray the AquaTRAM Series Pool Lifts 24v battery unit directly with any pressure Wipe all surfaces clean with a damp non abrasive cloth When cleaning the AquaTRAM Series Pool Lifts use non abrasive soap and water Avoid harsh chemicals and disinfectants Always read the label instructions on a
20. e CHARGE light will GO OFF and the battery is ready for use WHEN THE BATTERY IS NOT BEING USED IT SHOULD BE STORED ON THE CHARGER AND NEVER ON THE LIFT 11 BATTERY MAINTENANCE 1 WHEN LIFT IS NOT IN USE STORE BATTERY ON CHARGER The battery power unit is a sealed lead acid battery pack Frequent recharges will prolong the battery life and maintain a high cold amperage capacity THE BATTERY CAN BE STORED ON THE CHARGER WHEN NOT IN USE Do NOT expose the battery to freezing temperatures Do NOT expose the battery to prolonged periods of extreme heat or severe cold temperatures Do NOT expose the battery to long periods of direct sunlight Heat will shorten your battery life Optimum operating temperature is below 68 degrees F 20 degrees C Never drop or bump the battery pack This may result in loose or damaged internal connections and may bend the battery terminals Keep battery terminals clean and free from dirt and corrosion to ensure good contact The terminals may be cleaned using a Scotch Brite pad or any similar product Clean off any corrosion or discoloration on the very top surfaces of the battery contacts and then apply dielectric grease supplied with lift as shown in the figure below FIGURE 11 CLEAN WITH SCOTCH BRITE PAD AND APPLY DIELECTRIC GREASE TO TERMINALS 12 AQUATRAM LT POOL LIFT OPERATING INSTRUCTIONS WHEELCHAIR IN LOADING POSITION FULLY UPRIGHT POSITION FULLY LOWERED POSITION
21. f there is sufficient power in the battery the battery is properly attached to the control box and the control box must be operating properly 18 x i 1 E uw f ay E a E EE AQUATRAM LT POOL LIFT PARTS LIST L 10 HEX BOLT 5 SSS SR FLAT WASHER SS 1 o J L H ets HB n A s LN ELE L L 19 SEAT ASSEMBLY PARTS LIST 1 4 20 x 3 HEX BOLT S S 1 4 FLAT WASHER S S x 6 QUICK RELEASE PIN S S BL METAL SCREW S5 20 Options for AquaTRAMWM LT Adjustable Head Rest P N 11205 Includes e Padded head rest mounted to adjustable bracket with mounting hardware Adjustable Chest Strap P N 11206 Includes e Adjustable hook and loop style chest strap and mounting hardware Pullout Leg Rest P N 11208 Includes e Pullout leg rest to be factory installed Cycle Attachment P N 11207 Includes e Pedal attachment and mounting hardware cannot be used on lifts equipped with Pullout Leg Rest 11208 e 90 up turned hand grips for better support Protective Cover P N 11204 Transport Cart P N 11232 21 AquaTram LT Swimming Pool Lift Pentair Water TWO 2 YEAR LIMITED WARRANTY Commercial Pool and Aquatics A Division of Pentair Water Pool and Spa Inc AquaTram LT Lift has a Limited TWO YEAR Warranty on the frames not including the powder coat finish Pe
22. ntair Water Pool and Spa Inc Pentair also warrants to the original end user purchaser that the AquaTram LT Lift Lift when properly installed in accordance with assembly and installation instructions and properly used and maintained shall be free from defects in material and workmanship for a period of two 2 years from the date of original purchase provided that Pentair receives prompt notice in writing of any claim and satisfactory proof thereof This warranty specifically excludes reimbursement for labor to remove repair replace or install the Lift or component part thereof and any return freight charges These warranties do not cover any damages due to accident misuse abuse negligence or failure to properly maintain any Lift or component part thereof or normal wear and tear from day to day operations In the event that any Lift or component part thereof are altered repaired or improperly installed or improperly used by anyone without the prior written approval by Pentair all warranties are void IMPORTANT AMOUNT OF WEIGHT PLACED ON LIFT SHALL NOT EXCEED THE RATED LIFT CAPACITY OF 300 POUNDS 136 KG To initiate a warranty claim the owner of an AquaTram Lift must provide the place of purchase in writing with full description of the Lift its serial number the dates of purchase and installation and the exact nature of the claim Within thirty 30 days after receipt of a written warranty claim by Pentair and
23. ny cleaner carefully before applying it to a surface The WARNING 8 INTENDED USE labels on the AquaTRAM Series Pool Lifts must be maintained in readable fashion If they become unreadable or faded please replace the label immediately Replacement labels are available from Pentair Water Commercial Pool and Aquatics 1 800 831 7133 CARE OF YOUR LIFT Routine cleaning is an absolute necessity to ensure the integrity of the lift Note that the AquaTRAM LT Pool Lift should not be stored in a pump room or in a storage room where pool chemicals are kept Storing the lift near pool chemicals may cause rusting and other damage to occur Your AquaTRAM LT stainless steel lift is powder coated to protect the stainless steel from rusting Most rusting will occur at weld points crevices under gaskets rivets or bolt heads The choice of a proper cleaning product is up to the consumer and there are many to choose from Depending on the type of cleaning and the degree of contamination rusting some products are better than others For routine cleaning the products most recommended are gentle soaps or detergents or dilute mixtures of ammonia For stubborn spots and stains try using soft scrub with some brisk rubbing DO NOT USE POOL WATER TO CLEAN USE ONLY FRESH WATER If the lift is used DAILY make sure to wash the lift at the end of the day Wash the lift off using a mild soap and a soft cloth Make sure to pay special attention to weld points an
24. r system will need to be anchored differently than what these instructions outline contact Pentair Water Commercial Pool and Aquatics for assistance in this case The front anchors of the lift need to be mounted a maximum of 14 inches and no closer than 4 inches from the inside pool wall If your pool or spa has hand rails or other extensions on the inside of the pool wall the set back distance must take these into account Contact Pentair Water Commercial Pool and Aquatics for assistance in these types of applications In order to properly install this anchor system into an existing pool deck your pool deck MUST be at least 3 feet long by three feet wide and 6 inches thick It must also be reinforced with 4 rebar on 10 inch centers in both directions There may be instances where your existing pool deck may not be structurally sound enough or does not meet the minimum requirements outlined above for the safe installation of this anchor system In those circumstances it is recommended that you follow the Saw Cutting Retro fit Instructions on page 9 If you are installing this lift in a new application where the pool deck has not been poured yet then go to the New Construction instructions on page 10 FIGURE 1 AQUATRAM LT POOL LIFT CONCRETE DECK ANCHORED TO DECK us E REINFORCED W 4 REBAR 10 OC POOL EDGE a 56 A 56 jA OR FURTHESI m AQUATRAM LT FULLY LOWERED OBSTRUCTION 6 CENTERLINE OF FRONT NCHORS
Download Pdf Manuals
Related Search