Installation & User Manual Radio Remote RCS-10E - Side
Contents
1. Radio Remote RCS 10E rev1 1 Page 7 Replacing the battery bib 41 JE Me cM OTOST k 2 90 T 00149r 0 Hh T U lt m ht ue m T Fl L2 ae Td ca Ae MN A PS n c OD Wn 0 a rM nm x Eg LN ER L WARNING Before working on the transmitter deactivate the transmitter and the receiver push OFF on the transmitter s and turn off the power to the receiver as well as the thruster mainswitch 1 Open the transmitter 2 Take out the battery by inserting a screwdriver or similar between battery and holder at point A and gently flip the battery out taking care not damaging the battery grips at point B 3 Insert the new battery Type CR2032 3 Brand name recommended Be sure to insert the battery with the positive pole up diagonally into the battery holder confirming that the edge of the battery is under the battery grips B Press the battery down until secured at point A 4 Close the transmitter Put the cover back in place ensure that the rubber seal between remote upper and lower part is located correctly Place the 3 screws remember sealing washer in their recessed holes and tighten Installation amp User Manual Radio Remote RCS 10E rev1 1 Page 8 Important user precautions Ensure that you know the location of the main battery switch that disonnects the thruster from all power sources batteries so that the thruster can be turned off in c2. already inserted in the transmitter When additional transmitters are to be used the receiver must be programmed again for all trans mitters please see programming section on page 7 We Sleipner Motor AS declare that this device complies with health and safety requirements according to the Directives EN301 489 3 V1 4 1 2002 EN301 489 1 V1 4 1 2008 IEC 60533 1999 EN300 220 1 V2 3 1 2010 EN300 220 2 V2 3 1 2010 Installation amp User Manual Radio Remote RCS 10E rev1_1 Page 2 Technical specifications Transmitter Receiver Model RCT 10E RCRS 1E Power feed 1 x 3V battery type CR2032 From thruster Frequency MHz 433 2 433 2 Operation temp 10 C 55 C 15 C 55 C HxWxD mm 95x48x25 110x35x35 Weight g 60 170 Voltage 8 30V Operating range 15m under normal operating conditions Important precautions You must always install at least one original Side Power panel e With the boat on land only run the thruster for a fraction of a second as without resistance it will accelerate very fast to a damaging rpm This manual is intended to support educated experienced staff and is therefore not sufficient in all details for the correct installation When installed in boats approved or classified according to international or special national rules the installer is responsible for following the demands in accordance with these regula tions classification rules The instructions in this guide can
3. amp User Manual Radio Remote RCS 10E rev1_1 Page 6 Programming additional receivers m ann Conta Pecahan S lirk 7 ACT riu An Push the Pair Button The original transmitter and receiver have the same factory preset code so that no programming is necessary When additional transmitters are to be used the receiver must be programmed again for all transmitters 1 Deactivate the receiver and all transmitters press OFF on all transmitters Turn off the main power switch for the thruster s 2 Turn on the power to the receiver 3 Push the Pair Button on the receiver as shown above The LINK ACT LED over the button will start to blink 4 The receiver and transmitter are programmed by pressing both ON buttons on the transmit ter Within 5 seconds the LED will change from blinking to continous light when the program ming signal is received The transmitter is then ready to use 5 Additional transmitters must be programmed according to step 3 4 when the receiver is in Program mode You can pair up to 4 transmitters 6 To clear all transmitters hold Pair Button until LED blinks slow continue to hold button pressed until LED blinks quick indictaing that a reset process is started When LED is turned off the reset process is completed and the Pair button can be released The LED will come on when the receiver has completed the reset process and is ready to be paired Step 3 4 Installation amp User Manual
4. not be guaranteed to comply with all different regulations classification rules e The transmitter and the receiver have the same factory preset code so no programming is nec essary When additional transmitters are to be used the receiver must be programmed again for all transmitters please see programming section on page 7 If a Side Power automatic main switch is fitted the OFF button on your transmitter will shut off the main switch providing no other control panels are ON Installation amp User Manual Radio Remote RCS 10E rev1_1 Page 3 Receiver installation Prior to installation it is important that the responsible installer reads this guide to ensure necessary acquaintance with this product Caution Install the receiver minimum 1 meter 3ft from high power cables and NMEA cables or other sources of electrical interference i e navigation instruments radio communication devices electro motors and generators Install the receiver outside of shielded areas for radio signals i e boxes made of steel or other material with shielding properties Install the receiver in a dry environment The receiver assembly is not waterproof When additional transmitters are to be used the receiver must be programmed again for all transmitters please see programming section on page 7 The receiver is powered by the S link cable Mount the receiver using the four screw holes please see picture on page 6 If th
5. used at the same time if two panels are operated in oppo site directions at the same time the thruster will not run at all If they are operated in the same direction the thruster will run in this direction Installation amp User Manual Radio Remote RCS 10E rev1_1 Page 9 Remote control ON Turn boat to Port Bow Stern thruster Remote control OFF Auto OFF appr 4 min Hold for 2 seconds How to use a bow thruster 1 Turn the main power switch for the bow thruster on Turn on the power to the receiver 2 Turn on the transmitter by pushing the transmitter s two ON buttons The remote system is now activated and then turns off automatically appr 4 min after the last usage see page 9 3 Please take some time to exercise thruster usage in open water to avoid damages to your boat 4 Turn the bow in the desired directiony by pushing the red button for port movement or the green button for starboard movement How to use a bow amp stern thruster combined The combination of a bow and stern thruster offers total manouverability to the boat and the opportunity to move the bow and the stern separately of each other The remote middle buttons gives you the opportunity to operate both thrusters in the same direction with one keypress making sidewards movement easier Remote Control Deactivation Push the transmitter s OFF button for 2 seconds the remote control deactivates automati cally after app
6. Confidence by Control 4 P SIDE POVWVER Thruster Systems Installation amp User Manual Radio Remote RCS 10E tlPne SLEIPNER MOTOR AS FN P O Box 519 N 1612 Fredrikstad Norway I e Tel 47 69 30 00 60 www side power com Moto Fax 47 69 30 00 70 sidepower sleipner no Made in Norway Contents Mod iL 019 cR m dE 2 Technical SINS CNC AION uuu uu uuu co 3 Irportant aeneon 4 Mu lal FWD Y RH HR DN NN EY FFR NN RF NY TF TN FR RF TEES 6 INI diglielo ili 6 Programming additional transmittlers SO va Clav ala 7 WIS CI o FR ul NT FY RWE NAWS EF AFF REN YC HF A AR ARR A YR A Y RF PERRY A EF 8 UC MU UO Ho a Y iu GAF O GCE ED EOG ME FOOD 9 How to use Side Power thirusters 10 CIVICS CG RUE TH RYN FF CF AR RE WYN YNA CN YR NF NN RF FFY Y HF RT 12 Model range The radio remote control can control a single bow thruster or a bow and stern thruster combined The receiver can receive the signals of up to four transmitters Remote control kit RCS 10E consists of Receiver Part no RCRS 1E Transmitter incl battery Part no RCT 10E Holding bracket for transmitter unit Part no RC HOLDER Additional transmitters can be ordered separatly Part no RCT 10E Antenna is available as spare part no RC ANT The transmitter and the receiver have the same factory preset code so no programming is neces sary The battery is
7. ase of a malfunction If a Side Power automatic main switch is fitted the OFF button on your transmitter will shut off the main switch providing no other control panels are ON How to activate the system Turn on the main power source for the thruster system Turn on the power to the receiver The thruster system is then activated by pushing the two ON buttons on the transmitter see page 10 To turn of the radio remote control press the OFF button on the transmitter for 2 sec The LED below the Pair Button on the receiver will blink when a command signal is received Alarms If transmitter receiver is out of range the transmitter will give a alarm sound The transmitter will automatically turn off after approx 4 minutes of inactivity for safety reasons When using a single transmitter The system turns off automatically approx 4 minutes after the last usage When using more than one transmitter or additional radio link control panels The system turns off automatically approx 4 minutes after the last usage of the control unit that initially activated the system even if other control units have been operated in the meantime The system is off even if these other control units still show the blinking LED on the transmitter To use these transmitters the system must be activated again by pushing the two ON buttons Remember to turn off the radio remote control by pushing the OFF button on the transmitt
8. e receiver is mounted against a wall use spacers between the receiver and the wall to avoid moisture in the receiver Optimised installation Fig 1 3 The receiver antenna must be placed in a vertical position minimum 1 meter 3ft above sea level The receiver has antenna with SMA connector If there is a problem with signal transferring try to move the unit to a more optimised position or buy the antenna extension cable RC EXT to relocate the antenna Above sea level Away from sources of electrical interference Note Faulty installation will render all warranty given by Sleipner Motor AS void Installation amp User Manual Radio Remote RCS 10E rev1_1 Page 4 LINK ACT snaens gt ul O LIVAN H Installation amp User Manual Radio Remote RCS 10E rev1_1 Page 5 Receiver installation Sirk sir LIP AT BR a a E wir m iN Art gt lim amp stabs BIDE PIRNER Mount the receiver by using the 4 screwholes Receiver LEDs S link status LED Status User action Blinking green No activity on S link Bus If remote control is active and thrusters is not responding check S link cable connection LINK ACT LED Status User action or Remoeot Flash Receiving message from RCT 10 transmitter Blinking PAIR button is pressed ready for Pairing procedure decribed on pairing page 7 Installation
9. er for 2 seconds and to turn off the power switch for the receiver when you have finished your maneuvering The maximum continues usage time of the electrical thruster is approx 3 minutes The electro motor has a built in thermal cut off switch that will shut it off when overheating and re engage it when it has cooled down some This should be considered when planning your manouvering Never use a thruster close to somebody in the water as the thruster will draw objects close by into the tunnel and contact with the rotating propellers will cause serious injuries Never run a thruster for more that one second when the boat is not in the water as this can damage the electromotor seriously If the thruster stops giving thrust while the electromotor is running chances are that there is a problem in the drive system You must then immediately stop trying to run it and turn it off as running the electromotor for more than a few seconds without resistance from the propeller can cause serious damage to the electromotor When leaving the boat always turn off the main power switch for the thruster and turn off the power to the receiver We advice to always keep the main engine s running while using a thruster This will Keep the batteries in a good charge condition This will also give better performance to the thruster as a higher voltage at the thruster results in a higher torgue power in the electromotor Make sure that only one control is
10. rox 4 minutes after the last usage Turn off the power switch for the receiver If in doubt try in open water first Installation amp User Manual Radio Remote RCS 10E rev1_1 Page 10 06 1 Radio Remote RCS 10E rev1 1 Pa Installation 8 User Manual japow das 18 SNJY Mog LUG 9 geonjnul poxi Joeuluuep pug Jej oJ3u02 J49MOd Puo odold i Apuejod Kiayeq Odd 9A19SAO asn INV M 95 INY M UO IMS Ureui ENUEIN Aieneg Aioneg UOJIMS uieu ENUEIN JO JejsnJu uiejs Jejsniuy Mog vc 2169 CV 8 vc Z269 CV 8 76 61 YG Avda Avec Ajddns yui s Avelel VS uos Jo uo 4ul S r1 9 ulejs s xui S JOAI929J 9jOUJOJ Xul S uoneis yons or IPeuoiuodoid CIC Ofd J llo uoS JOMOd Wg poxi i ISPA 9 Jojeuiuuoa Puy c uonejs jeuedonuoo yousAor cic 9fd iIepou das JejsnJuj uJe s ICS hemati IC SC Electr Worldwide sales and service www side oower com Gy Moto SLEIPNER MOTOR AS PO Box 519 N 1612 Fredrikstad Norway Tel 47 69 30 00 60 Fax 47 69 30 00 70 www side power com gt sidepower sleipner no
Download Pdf Manuals
Related Search