Océ 7050/7051
Contents
1. 16 Repositioning the roll 11 Feed the copy material into the feeder with one hand and turn the roll feeding knob with the other hand in the direction of the arrow Note Make sure that the copy material is fed into the feeder in a straight way Note You can use the front or the back roll to feed the material 12 Hold the copy material with one hand and move the cutter with your other hand entirely to the left or right side to cut the surplus of material 13 Close the drawer Oc 7050 7051 User Manual Adding toner If the toner level is low the add toner indicator starts flashing You can finish your job Then add toner Attention If you ignore this symbol copy quality will diminish v Adding toner 1 Switch off the copier 2 Unscrew the knurled nut at the left hand side of the machine and open the cover figure 17 17 Unscrewing knurled nut and opening the cover 3 Shake the toner bottle thoroughly and open the bottle Attention Only use B1 toner Materials 27 4 Screw in the bottle clockwise in a slanted position figure 18 18 Screwing in the bottle 5 Move the toner bottle to a vertical position figure 18 and 19 19 Adding toner 6 When the toner bottle is empty return the bottle to the original position 7 Unscrew the toner bottle anti clockwise Oc 7050 7051 User Manual Replacing the waste toner bag 8 Pull the2. Oc Thailand Ltd 16th Floor B B Building 54 Asoke Road Sukhumvit 21 Bangkok 10110 Thailand Oc U K Ltd Langston Road Loughton Essex IG10 3SL United Kingdom Oc USA Inc 5450 North Cumberland Av Chicago Ill 60656 U S A Index A add toner indicator 27 adding toner 27 bag replacing waste toner 29 CG cleaner a 31 cleaning glass platen 30 pressure plate 30 copy feed 17 copy feed table 36 copy length counter 16 copy material 7 copy material roll inserting a new 24 copy material selection button 12 13 copy quantity 7 correction button 7 13 14 15 counter copy length 16 cutter 17 D dew preventer 10 display selection 7 E exposure 19 exposure scale 7 exposure setting 19 Index F fuser 37 image shift 20 K knob roll feeding 17 L length copy counter 16 original 17 manual roll making copies using 15 O on off switch 9 operating panel 7 original feed 14 15 original length 8 17 P paper path indicator 34 35 36 39 paper inserting a new roll 24 pressure plate 30 69 R roll inserting a new copy material 24 making copies using the manual 15 roll feeding knob 17 S safety data sheets 53 safety information 50 stop button 7 switch off 9 switchon 9 T toner adding 27 replacing waste bag 29 top cover 35 trailing edge 8 20 21 transparent platen 30 W waste toner bag
3. 0 05 mm 1 5 mm Weight 60 g m 120 g m max 210 g m Mechanical conditions originals Curls gt 75mm without help of operator lt 75 mm with help of operator lt 50 mm in carrier sheet Paste ups Paste ups should be pasted 100 at all edges or in carrier sheet Filing strips May be present at all edges of the original Maximum size of hole 36 mm Borders Punching holes reinforcement borders and damages may require operator interventions or use of carrier sheets Folds Wrinkles and folds may be visible on the copy Overview and tables 45 Copy material that can be used 46 Oc copy machines and materials are matched for optimal quality and performance It is therefore recommended to use only approved Oc materials in the Oc 7050 7051 A full list of Oc materials suited for use in the Oc 7050 7051 including plain paper transparent paper coloured papers and various polyester films is available from your Oc representative The maximum roll length of the copy material is 175 m when you use 75 g m copy material and 150 m in case of 110 g m The diameter of the roll holder equals 3 inch Overview of copy material Copy material Recommended Plain paper 75 g m Transparent paper 110 g m Vellum 20 Ibs Polyester film 3 5 mil ECO papers 75 g m Minimum Maximum Width 297 mm 914 mm Length 420 mm any manageable length Attention Paper and transparent material is sensitive to high
4. 29 70 Oc 7050 7051 User Manual
5. The content of this safety data sheet is subject to the disclaimer on page 53 of this manual Oc 7050 7051 User Manual Safety data sheet Oc D1 Developer MATERIAL SAFETY DATA SHEET Number E 181 b UK 93 112 EEC and ISO 11014 1 Date July 1997 Page 1 of 2 Oc D1 Developer Composition Product and company identification Product name Oc D1 Developer Packing Polyethylene bottle contents 1 65 kg 3 63 Ib formation on ingredients Ingredients CAS No Classification Weight Iron oxide 1317 61 9 50 100 Polyester resin 170831 75 1 15 Phenoxy resin PMN P 95 461 1 5 Carbon black 1333 86 4 lt 1 Dye lt 1 Pigments lt 1 Hazards identification In a developer dust cloud the formation of an explosive dust air mixture is possible Developer dust may cause discomfort for the eyes and respiratory tract in the same manner as inert nuisance dust To our knowledge with due observance of the recommended exposure limit and of normal hygiene this product presents no health hazard in normal use First aid measures Eyes contact Rinse with plenty of water Skin contact Wash with cold water and soap Inhalation Clean nose mouth throat Cough up Fresh air Ingestion Rinse mouth with water If large quantity swallowed seek medical advice For any medical advice take along this material safety data sheet Fire fighting measures Flash point C N A Not Applicable Explosion limits dust e
6. any implied warranties of merchantability or fitness for any particular purpose Further Oc Technologies B V reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation to notify any person of such revision or changes Code number 7055817 Edition 3 1 Contents Chapter 1 Introduction The Oc 7050 7051 6 The operating panel 7 Switching on off 9 Dew Preventer optional 10 Chapter 2 Copy jobs Introduction 12 Making copies 13 Special settings 19 Exposure setting 19 Trailing edge Oc 7051 only 20 Chapter 3 Materials Inserting a new copy material roll 24 Adding toner 27 Cleaning the transparent platen 30 Chapter 4 Solving problems Introduction 34 Clearing original jams 35 Clearing paper jams 36 Operator recoverable errors 39 Machine errors 40 Contents Appendix A Appendix B Overview and tables Standard settings 42 Product specifications 43 Roomtemperature T and Relative Humidity RH 44 Originals that can be used 45 Copy material that can be used 46 Safety information Instructions for safe use 50 Mains core colours 52 Safety data sheets 53 Safety data sheet Oc 7050 7051 54 Safety data sheet Oc B1 Toner 55 Safety data sheet Oc D1 Developer 57 Safety data sheet Oc OPC Drum 59 Safety data sheet Oc Cleaner A 61 EPA Energy Star 62 Appendix C Miscellaneous Notation conventions 64 Reader s comment s
7. Handling and storage Keep bottle tightly closed to prevent dust formation Handle carefully Avoid breathing dust No special technical measures for storage 8 Exposure controls personal protection No special technical measures No personal protective equipment needed Industrial hygiene after skin contact wash with cold water and soap Threshold Limit Value for nuisance dust 10 mg m Threshold Limit Value for carbon black 3 5 mg m continued on the next page Safety information 56 MATERIAL SAFETY DATA SHEET Number E 180 b UK 93 112 EEC and ISO 11014 1 Date July 1997 Page 2of2 Oc B1 Toner 9 Physical and chemical properties Appearance and odour Black powder faint odour Boiling point C N A Bulk density kg m Approx 1250 Vapour density air 1 NA Softening point C Approx 50 Solubility in water Insoluble Evaporation rate butyl acetate 1 N A Vapour pressure NA Volatile o Other characteristics NA PH solution NA 10 Stability and reactivity Thermal decomposition Above approx 450 C Hazardous decomposition products None at intended use Hazardous reaction None at intended use 11 Toxicological information Inhalation At high concentration in air the powder may cause discomfort of upper respiratory system Skin No adverse health effects are expected Eyes Dust may cause discomfort in the same manner as nuisance dust Ingestion Consid
8. Oc 7050 7051 User Manual Oc Technologies B V This manual which can be kept behind the left hand door of the copier contains a description of the Oc 7050 7051 and the copying that can be done with it The introduction chapter 1 contains a general description of the working methods for using the copier and it is recommended that you read at least this chapter Overview of copier parts on the covers To assist you in finding parts of the copier and the functions on the operating panel quickly an illustration of the Oc 7050 7051 is presented on the inside front cover and of the operating panel on the inside back cover both of which can be folded out Safety information This manual contains the following safety information m Appendix B lists Instructions for safe use You are advised to read this information before you start to actually use the copier Technical safety information such as safety data sheets can also be found in appendix B m Where applicable cautions and warnings are used throughout this manual to draw your attention to safety precautions to be taken Copyright Oc Technologies B V Venlo The Netherlands 1999 All rights reserved No part of this work may be reproduced copied adapted or transmitted in any form or by any means without written permission from Oc Oc Technologies B V makes no representation or warranties with respect to the contents hereof and specifically disclaims
9. an 2 minutes it returns automatically to stand by mode The Oc 7050 7051 however remains always ready for operation Stop button The stop button stops the current copy process immediately without finishing the current job The original and the copy material remain in the copier Exposure scale lighter darker You modify the exposure scale with the lighter and darker buttons The exposure scale can be changed at all times Copy material selection button film paper You can use this button to select the copy material Your selection paper or film influences the fusing temperature All materials except for film should be copied in the paper setting Copy quantity selection button Oc 7051 only Press these buttons to increase or decrease the number of copies as shown in the copy quantity display The copy quantity can be changed at all times Correction button Oc 7051 only Resets the copy quantity counter to 1 By pressing the correction button twice all settings will reset to the standard settings see Standard settings on page 42 Display selection button Oc 7051 with manual roll only By pressing the display selection button you can determine what will be shown on the Introduction 7 display at the top of the operating panel the original length in cm or the amount of trailing edge in mm One of the indicators will light up to show the current setting Trailing edge button
10. biodegradable The ingredients are not classified as ecologically hazardous No adverse environmental effects are expected 13 14 Disposal considerations The drum will be returned to Oc for re use formation Transport This product is not classified as a dangerous substance according to the international transport regulations 15 Regulatory information This product is an article and contains no dangerous substances Therefore indications of special risks or safety advice on the packing are not prescribed for this product 16 Other information Use photoconductor for copiers Revision of E 192 a UK dated December 1994 Modification none 1997 Oc Technologies B V The content of this safety data sheet is subject to the disclaimer on page 53 of this manual Oc 7050 7051 User Manual Safety data sheet Oc Cleaner A Not yet available Safety information 61 EPA Energy Stare 62 Oc Technologies B V has joined the Energy Star Program of the United States Environmental Protection Agency EPA The purpose of the Energy Star Program is to promote the manufacturing and marketing of energy efficient equipment thereby potentially reducing combustion related pollution Using the energy management features outlined below prevents unnecessary power consumption which helps to prevent air pollution from electricity generating plants and saves money on your utility bills As an E
11. dioxide water spray fog foam Special fire fighting precautions N A Hazardous products of decomposition N A 6 Accidental release measures N A 7 Handling and storage No special technical measures for storage 8 Exposure controls personal protection No special technical measures No personal protective equipment needed No special work hygiene practices needed continued on the next page Safety information 60 MATERIAL SAFETY DATA SHEET Number E 192 b UK 93 112 EEC and ISO 11014 1 Date July 1997 Page 20f2 Oc OPC Drum Part No 2912571 9 Physical and chemical properties Appearance and odour brown odourless drum Boiling point C NA Density g cm 27 Vapour density air 1 NA Melting point C NA Solubility in water Insoluble Evaporation rate butyl acetate 1 NA Vapour pressure NA Volatile o Other characteristics NA PH solution NA 10 Stability and reactivity Thermal decomposition None at intended use Hazardous decomposition products None at intended use Hazardous reaction None at intended use 11 Toxicological information Inhalation NA Skin No adverse health effects are expected Based on toxicological literature on the ingredients of this product Eyes NA Ingestion NA Mutagenicity No mutagenicity detected in Ames test None of the ingredients is listed as mutagenic or carcinogenic Ecological information This product is not
12. ed as separate option Only in extreme humidity conditions it is recommended to switch on the Dew Preventer to enhance copy quality Y Switching on Dew Preventer 1 Set the Dew Preventer switch at the rear of the machine to position 1 see figure 2 If the machine is switched on the green switch will light up a SES ESS DAS RDS r 2 Dew Preventer switch Note The Dew Preventer will only be effective if it is left on Y Switching off Set the Dew Preventer switch at the rear of the machine to position 0 see figure 2 10 Oc 7050 7051 User Manual Oc 7050 7051 User Manual Chapter 2 Copy jobs Making copies and special settings Introduction The Oc 7050 7051 enables copies to be made on paper transparent vellum and polyester film By pressing the copy material selection button you can make your choice The standard setting of the copy material selection button is paper Only when using film this button has to be pressed to change to film All other materials should be copied on the paper setting Note Make your choice before feeding the original It is most convenient to feed the original first When feeding the original it is transported to the rear of the machine The display will show the original length When you now feed the copy material the original returns to the front in order to make a copy Note Only use paper as i
13. ered relatively harmless Mutagenicity No mutagenicity detected in Ames test These statements are based on toxicological literature on the ingredients of this product and test results of similar products 12 Ecological information This product is not biodegradable The ingredients are not classified as ecologically hazardous No adverse environmental effects are expected 13 Disposal considerations Pack waste dustproof to prevent dusting With due observance of local laws and regulations dispose of by burial in a sanitary landfill or incineration Do not throw in open fire in order to prevent the risk of a dust explosion 14 Transport information This product is not classified as a dangerous substance according to the international transport regulations 15 Regulatory information This product is not classified as a dangerous preparation according to the European Directives 67 548 EEC and 88 379 EEC for the classification packaging and labelling of dangerous substances and preparations Therefore indications of special risks or safety advice on the packing are not prescribed for this product 16 Other information Use ink powder for copiers Room ventilation see operator manual or safety data sheet for the copier Revision of E 180 a UK dated November 1994 Modifications Statement of mutagenicity softening point and information on ingredients changed 1997 Oc Technologies B V
14. f this equipment may not correspond with the coloured markings identifying the terminals in your plug proceed as follows m The core which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol coloured green and yellow m The core which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black m The core which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red Oc 7050 7051 User Manual Safety data sheets The disclaimer below is valid for all safety data sheets in this manual For questions about Oc products regarding health safety and environment please contact your Oc organisation you can find the address in the last appendix of this manual Disclaimer The safety data sheets in this manual have been compiled to the best of our knowledge as a compact guide to safe handling of this product We reserve the right to revise safety data sheets as new information becomes available It is the user s responsibility to determine the suitability of this information for the adoption of safety precautions as may be necessary and to contact the company to make sure that the sheet is the latest one issued If and in so far as limitation of liability is permitted under the applicable laws we do not accept liability for any inaccuracy that may occur in this informatio
15. f this manual convenient in size readability and arrangement page layout chapter order etc Ll Yes D No Could you find the information you were looking for D Always D Most of the times Q Sometimes D Not at all What did you use to find the required information D Table of contents D Index Are you satisfied with this manual Ll Yes D No Thank you for evaluating this manual If you have other comments or concerns please explain or suggest improvements overleaf or on a separate sheet 7055817 Miscellaneous 65 Comments Date This reader s comment sheet is completed by If you prefer to remain unknown please do fill in your occupation Name Occupation Company Phone Address City Country Please return this sheet to Oc Technologies B V For the attention of ITC User Documentation P O Box 101 5900 MA Venlo The Netherlands Oc 7050 7051 User Manual Addresses of local Oc organisations Oc Australia Ltd P O Box 363 Ferntree Gully MDC VIC 3165 Australia Oc Osterreich GmbH Postfach 95 1233 Vienna Austria Oc Belgium N V S A Avenue J Bordetlaan 32 1140 Brussels Belgium Oc Brasil Com rcio e Industria Ltda Caixa Postal 3187 01060 970 Sao Paulo SP Brazil Oc Canada Inc 525 Logan Avenue Toronto Ontario M4K 3B3 Canada Oc Office Equipment Beijing Co Ltd Xu Mu Cheng Chaoyang District Beijing 100028 China Oc Cesk re
16. he Oc 7050 7051 is configured with a number of standard settings Standard settings Oc 7050 7051 Exposure scale 0 Copy material paper Trailing edge Oc 7051 only 0 mm Copy quantity Oc 7051 only 1 Oc 7050 7051 User Manual Product specifications For more information about product specifications refer to the Oc 7050 7051 safety data sheet in Appendix B Product specifications Process Exposure Developing system Fixing system Warm up time Scale Image width Copying speed Machine size Machine weight Overview and tables Dry indirect electrostatic Slit exposure with one fluorescent lamp and SLA Binary toner system Instant heating system none 1 1 4 0 5 Max 914 mm 36 3m min Oc 7050 7051 1352 x 795x 400 wxdxh in mm Oc 7050 7051 with manual roll 1352 x 918 x 1251 wxdxh in mm Oc 7050 7051 85 kg copy material excluded Oc 7050 7051 with manual roll 136 kg copy material excluded 43 Roomtemperature T and Relative Humidity RH 44 A Machine specifications are applicable for the following conditions B Copy quality not guaranteed no permanent machine damage RV 80 60 30 20 A E IN p 17 20 27 30 T C Oc 7050 7051 User Manual Originals that can be used Overview of originals Originals Minimum Maximum recommended Width 210 mm 1000 mm Length 279 mm 3000 mm Length in retention 1200 mm Thickness
17. heet 65 Addresses of local Oc organisations 67 Index 69 Oc 7050 7051 User Manual Oc 7050 7051 User Manual Chapter 1 Introduction This chapter contains a general description of the Oc 7050 7051 and how to get the copier ready to copy The Oc 7050 7051 The Oc 7050 7051 is a copier for large documents e g architectural or engineering drawings The machine is easy to use and makes copies on paper transparent vellum or polyester film with the quality and reliability that one might expect from Oc The Oc 7050 7051 has a copy feed table for manual copy material input and as optional a manual roll for copy material Explaining figures of the Oc 7050 7051 and its operating panel can be found on the inside covers 6 Oc 7050 7051 User Manual The operating panel The operating panel see the illustration on inside back cover on the Oc 7050 7051 is easy to use and specially designed to carry out copy jobs After switching on see page 9 the machine is always ready for operation The operating panel on the Oc 7050 7051 with manual roll will show blinking LEDs on the display to indicate that the machine is ready for operation In this state the operating panel is in stand by mode The operating panel activates in the following situations m you feed an original you feed a copy material a button on the operating panel is pressed Note If you do not work with the operating panel for more th
18. hould be copied with the copy material selection set to paper Only select the setting film if you make copies on polyester film Oc 7051 only Select the desired number of copies by pressing the or button on the operating panel see figure 5 Note Changing the copy quantity can be done at all times When you make a mistake you simply press the correction button to correct the copy quantity Oc 7051 x add toner rl ov LI paperpath SE C correction L Q S stop 5 Setting more than one copy using the or button Feed the original centrally and face down into the original feed table in accordance with the guidelines see figure 6 on page 16 Note The original is aligned in the nip of the rollers By inserting the material with an amount of slack the leading edge is aligned in the nip A delay between insertion of the material and the start of the transport ensures proper alignment Copy jobs 15 The original is transported to the rear of the machine and the display shows the length of the original in cm Note After 2 minutes the operator panel returns to the ready mode When you wait more than 2 minutes you have to re feed your original Attention Strongly curled originals have to be fed in carefully In certain circumstances the copier can pull the original in 6 Feeding an original 4 Make sure that the cutter is moved enti
19. humidity To ensure optimal copy quality it is advised to keep the copy materials in the packaging specially overnight Caution Materials which are metal based or conductive are not designed to use in this machine and may result in injury to the operator Attention If sheets of copy material are curled feed them in with the curl facing down otherwise you will damage the drum Oc 7050 7051 User Manual Compatibility review media Materials Weight Opaque paper 75 g m Opaque paper 110 g m ECO papers 75 g m Transparent paper 80 85 g m 90 95 g m 110 115 g m Polyester film 3 5 mil Clear polyester film 4 mil Contrast film 3 5 mil Vellum 20 Ibs Vellum 16 Ibs Contrast paper 135 g m Fluor paper 90 g m Pastel paper 80 g m Good Acceptable Not suitable means fully recommended means not suitable at all Overview and tables Judgement Remark good acceptable good acceptable Guaranteed up to 50 RH acceptable acceptable good good acceptable good good acceptable acceptable Guaranteed up to 50 RH acceptable acceptable means acceptable for limited performance 47 48 Oc 7050 7051 User Manual Appendix B Safety information Oc 7050 7051 User Manual Instructions for safe use 50 Oc copiers and materials have been developed and tested in accordance with the strictest international safety standards To ensure safe working with these products it is important that you obser
20. in the title It might also include possible applications as well as any guidelines that you should bear in mind Procedures A description is followed by a procedure A procedure always begins with a phrase which briefly describes the procedure followed by a series of numbered steps that take you step by step through all phases of performing the operation Figures and tables Figures and tables are titled and numbered sequentially throughout this manual Figures include pictures of product components screendumps examples and diagrams of concepts discussed in the description Attention getters There are several types of information to which we draw your attention This information is classified as follows Note In a Note information is given about matters which ensure the proper functioning of the machine or application but useful advice concerning its operation may also be given Attention The information that follows Attention is given to prevent something your copy or original the copier or printer data files etc being damaged Caution The information that follows Caution is given to prevent you suffering personal injury Oc 7050 7051 User Manual Reader s comment sheet Have you found this manual to be accurate Ll Yes D No Could you operate the product after reading this manual Q Yes Q No Does this manual provide enough background information Q Yes Q No Is the format o
21. l has a filing strip and you don t want that to show on the copy it is possible to shift the image at the trailing edge Make sure that the filing strip is at the trailing edge of the original see figure 11 The adjustment steps are indicated on the operating panel expressed in millimetres 11 Example of adjusting the trailing edge v Adjusting the trailing edge 1 Press the display selection button to show the trailing edge on the display The trailing edge indicator will light up 20 Oc 7050 7051 User Manual 2 Set the desired length of the trailing edge with the trailing edge buttons for example 40 see figure 12 Note The trailing edge can vary 40 to 100 mm in steps of 5 mm Oc 7051 O trailing edge D original length Li 12 Trailing edge buttons 3 Press the button to shift the image towards the leading edge 4 Press the button to shift the image towards the trailing edge Attention Be aware that when shifting the image too much this may result in the loss of information at the edge that the image was shifted to In this situation longer copy material is necessary Copy jobs 21 22 Oc 7050 7051 User Manual Oc 7050 7051 User Manual Chapter 3 Materials This chapter describes how to insert a new copy material roll how to add toner and how to clean the transparent platen 23 Inserting a new copy mate
22. mal decomposition Above approx 450 C Hazardous decomposition products None at intended use Hazardous reaction None at intended use 11 12 13 14 Toxicological information Inhalation At high concentration in air the powder may cause discomfort of upper respiratory system Skin No adverse health effectsare expected Eyes Dust may cause discomfort in the same manner as nuisance dust Ingestion Considered relatively harmless Mutagen No mutagenicity detected in Ames test of similar products These statements are based on toxicological literature on the ingredients of this product and test results of similar products Ecological information This product is not biodegradable The ingredients are not classified as ecologically hazardous No adverse environmental effects are expected Disposal considerations Pack waste dustproof to prevent dusting With due observance of local laws and regulations dispose of by burial in a sanitary landfill or incineration Do not throw in open fire in order to prevent the risk of a dust explosion Transport information This product is not classified as a dangerous substance according to the international transport regulations 15 Regulatory information This product is not classified as a dangerous preparation according to the European Directives 67 548 EEC and 88 379 EEC for the classification packaging and labelling of dangerous substances and preparations The
23. n Note Not all safety data sheets were available at the moment this manual was published The Oc organisation in your country will be pleased to send you a copy of the missing sheets You can find the address of the Oc organisation in your country in the last appendix of this manual Safety information 53 Safety data sheet Oc 7050 7051 Oce Number E 647 b UK Date May 1995 Model Oc 7050 7051 Description Plain paper engineering large format copier desk top or console model Max process speed 3 m min incl stand incl shelves incl man roll Dimensions Width 1352 mm 1352 mm 1352 mm 1352 mm Depth 795 mm 795 mm 795 mm 918 mm Height 400 mm 1251 mm 1251 mm 1251 mm Weight 85 kg 114 kg 127 kg 142 kg Voltage 230 V Frequency 50 Hz Current rated 75 A Current max 10 A Power consumption operation 1500 W Power consumption standby 10 W Mains connection Cable with plug Safety class 1 IEC 536 Protective earth connection Protection class IP 20 IEC 529 Sound pressure level Sound power level Radio interference Radiation Heat emission Ozone emission At operator position in operation 58 dB A impulse In operation 65 dB A Complies with Directive 89 336 EEC Below the Threshold Limit V alue for UV radiation TL V list of ACGIH Standby 10 W in operation 1500 W 0 04 mg min at continuous operation A Li 3 dB A Room volume Room ventilation Use simulation at random operation Rec
24. nergy Star Partner Oc Technologies B V has determined that the Oc 7050 and 7051 large format copier models meet the Energy Star guidelines for energy efficiency The EPA Energy Star criteria for these large format copiers involve the following features auto off mode The use of the auto off feature offers economic and environmental benefits The copiers are shipped with the auto off mode default time set at 2 minutes which means that the device switches itself off 2 minutes after the last copy is made The auto off mode default time is a fixed value and cannot be adjusted The auto off mode recovery time is less than 1 second after which copying can be resumed instant copying recycled paper The use of recycled paper also benefits the environment These copiers are designed to use recycled paper Product literature on recommended types of recycled copier paper can be obtained from your local Oc company or Oc Headquarters Oc Technologies B V in Venlo the Netherlands litt S Energy Star is a U S registered mark Oc 7050 7051 User Manual Appendix C Miscellaneous Oc 7050 7051 User Manual Notation conventions There are a number of notation conventions used in this manual This consistent style enables you to quickly become conversant with the use of this manual and consequently the Oc 7050 7051 Description Each section or subsection contains a description of the feature or operation identified
25. nsport ensures proper alignment Copy jobs 17 18 10 Attention Do not turn the copy material before feeding to ensure that possible curls in the copy material are facing down 9 Feeding the copy material Oc 7051 only After making a copy the copy quantity counter at the bottom of the operating panel decreases by one Repeat step 4 to 9 until the copy counter is set to 0 If you want to make more copies of the same original you don t have to feed the original again as long as you haven t pulled it from the original feed table By pulling out the original the counter will be set to 1 Oc 7050 7051 User Manual Special settings Exposure setting When copying extremely light or dark originals or originals with unequal background density the result may not meet your requirements e g too much background In such cases you can adjust the exposure scale In the default setting the exposure scale indicator is in the neutral position see figure 10 Oc 7050 7051 4 2 film ar d er E paper 0 6 on 4 darker 10 Exposure setting v Exposure setting 1 Ifthe copy is too dark you can modify the exposure scale using the lighter button 2 Ifthe copy is too light you can modify the exposure scale using the darker button Copy jobs 19 Trailing edge Oc 7051 only If for example your origina
26. oblems 35 Clearing paper jams 36 When paper feeds incorrectly the paper path indicator will flash Clearing a paper jam in the copy material feed section Switch off the copier Lower the copy feed table using the two catches on the front underneath the copy feed table see figure 24 24 Lowering the copy feed table Remove the jammed copy material Attention Make sure the copy feed table is lowered before removing copy material Attention Pull the sheet of paper backwards carefully the sheet might be unfused on some parts Note Check thoroughly that no scraps of material are left behind Close the copy feed table Switch on the copier Oc 7050 7051 User Manual If the paper jam can not be cleared by opening the copy feed table than open the fusing section by 1 Switch off the copier 2 Unscrew the knurled nut at the left hand side of the machine and open the cover see figure 25 25 Opening the left cover at the rear of the machine 3 Lift the green handle and open the fuser unit see figure 25 and 26 Caution If the copier has been used recently the fuser may still be hot 26 Opening the fuser unit Solving problems 37 Remove the jammed copy material Attention Be careful The toner is not fused Note Check thoroughly that no scraps of material are left behind Lift the green handle and close the fuser unit Close
27. ocket that is easily accessible The switch in the fixed connection if any should be easily accessible This copier has not been designed for connection to an IT power system An IT power system is a voltage network in which the neutral wire is not connected to earth Do not block the ventilation openings of the copier Ensure that the copier is placed on a level horizontal surface of sufficient strength See the Oc 7050 7051 safety data sheet in this appendix for information about the weight of the copier Ensure there is sufficient space around the copier This facilitates reloading materials as well as maintenance Oc 7050 7051 User Manual Do not place the copier in rooms which are subject to excessive vibration Do not place the copier in rooms which are too small and insufficiently ventilated See the Oc 7050 7051 safety data sheet in this appendix for information about space and ventilation requirements a Always use materials recommended by Oc and developed for this Oc copier Materials not approved by Oc may result in faults in your copier Do not use the copier when it is emitting unusual sounds Remove the plug from the power socket and contact Oc Customer Service a To avoid temporary visual inconvenience do not look directly into the light if possible close the cover before starting a copy job Safety information 51 Mains core colours As the colours of the cores in the mains lead o
28. ommendation min 25m Recommendation min 12 5 m h natural ventilation Room volume and ventilation as recommended Daily copy volume much more than average 100 m Total worktime 8 h Ozone concentrations Time weighted average 0 002 mg m 0 001 ppm Peak 0 008 mg m 0 004 ppm Threshold Limit V alue Occupational Exposure Limit Time W eighted A verage for ozone 02 mgm 0 1 ppm Odour Perception Limit for ozone 004 mgm 0 02 ppm Consumables Oc OPC Drum Oc Safety Data Sheet E 192 Oc B1 T oner Oc Safety Data Sheet E 180 Oc D1 Developer Oc Safety Data Sheet E 181 Oc Copying Materials Marking CE Compliance Approved according to Low Voltage Directive 73 23 EEC cS Approved according to EMC Directive 89 336 EEC Additional safety information During the projected lifetime of the copier exceed 0 04 mg m Therefore replacement of the ozone filter will not be necessary the ozone concentration in the workplace will not 1997 Oc Technologies B V The content of this safety data sheet is subject to the disclaimer of liability on page 53 of this manual 54 Oc 7050 7051 User Manual Safety data sheet Oc B1 Toner MATERIAL SAFETY DATA SHEET Number E 180 b UK 93 112 EEC and ISO 11014 1 Date July 1997 Page 1 of 2 Oc B1 Toner 1 Product and company identification Product name Oc B1 Toner Packing Polyeth
29. ow to proceed in case a problem arises 33 Introduction This chapter documents problems that may occur with the Oc 7050 7051 and how to solve them When an error occurs the operating panel informs you about the nature of the problem Oc 7050 7051 with manual roll m if the paper path indicator flashes a paper jam has occurred see Clearing original jams on page 35 and Clearing paper jams on page 36 a if the display shows an error code i e between E0 and E2 an operator recoverable error has occurred see Operator recoverable errors on page 39 m if the display shows a flashing 4 digit error code a machine error has occurred see Machine errors on page 40 Oc 7050 7051 User Manual Clearing original jams o A When during copying an original jam occurs the paper path indicator will start 2 flashing and the display shows the error message EO v Clearing an original jam 1 Switch off the copier 2 First try to remove the jammed original by pulling it gently towards you with both hands In case of a very fragile original 3 Open the top cover by pulling it towards you and raising the cover see figure 23 23 Opening the top cover 4 Remove the original 5 Close the top cover and push it back until you hear a click 6 Ifthere is copy material in the copier clear copy path see Clearing paper jams on page 36 7 Switch on the copier Solving pr
30. publika s r o Hanusova 18 14021 Praha 4 Pankrac Czech Republic Miscellaneous Oc Danmark A S Kornmarksvej 6 DK 2605 Br ndby Denmark Oc France S A 32 Avenue du Pav Neuf 93161 Noisy le grand Cedex France Oc Deutschland GmbH Postfach 101454 4330 Miilheim an der Ruhr 13 Deutschland Oc Hong Kong China Ltd 12 F 1202 The Lee Gardens 33 Hysan Avenue Causeway Bay Hong Kong Oc Hungaria Kft P O B 237 1241 Budapest Hungary Oc Italia S p A Strada Padana Superiore 2 B 20063 Cernusco sul Naviglio MI Italia Oc Systems Malaysia Sdn Bhd 3 01 Level 3 Wisma Academy Lot 4A Jalan 19 1 46300 Petalig Jaya Malaysia 67 Oc Nederland B V P O Box 800 5201 AV s Hertogenbosch The Netherlands Oc Norge A S Postboks 53 Grefsen 0409 Oslo 4 Norway Oc Poland Ltd ul Lopuszanska 53 02 0232 Warszawa Poland Oc Lima Mayer S A Av Jos Gomes Ferreira 11 Ed Atlas IT Miraflores 1495 Alg s Portugal Oc Far East Pte Ltd Oc Singapore Pte Ltd 03 00 Wisma Gulab 190 MacPherson Road Singapore 348548 Oc Espafia SA Business Park MAS BLAU C Osona 2 2 3a Planta 08820 El Prat del Llobregat Barcelona Spain Oc Svenska AB P O box 1231 S 164 28 Kista Sweden Oc Schweiz AG S gereistrasse 29 CH8152 Glattbrugg Switzerland 68 Oc 7050 7051 User Manual Oc Taiwan Ltd No 99 24 Nan Kang Road Sec 2 Taipeh Taiwan Taiwan RO
31. rally and face down into the original feed table in accordance with the guidelines see figure 4 4 Feeding an original Note The original is aligned in the nip of the rollers By inserting the material with an amount of slack the leading edge is aligned in the nip A delay between insertion of the material and the start of the transport ensures proper alignment The original is transported to the rear of the machine Attention Strongly curled originals have to be fed in carefully In certain circumstances the copier can pull the original in Note Minimum length of the copy material is 420 mm Oc 7051 only After the job is completed the copy counter will be set to 0 By pressing the button the original will be transported to the rear of the machine in order to make a next copy and the counter will be increased to 1 By pulling out the original the counter will be set to 1 Note Changing the set amount can be done at all times When you make a mistake you can press the correction button to correct the copy quantity Note After 2 minutes the operator panel returns to the ready mode When you wait more than 2 minutes you have to re feed your original Oc 7050 7051 User Manual Making copies using manual roll optional Press the copy material selection button to toggle between paper or film Attention Select the appropriate copy material to avoid flawed copies All materials except for film s
32. refore indications of special risks or safety advice on the packing are not prescribed for this product 16 Other information Use ink powder for copiers Room ventilation see operator manual or safety data sheet for the copier Revision of E 181 a UK dated December 1994 Modifications Statement of mutagenicity softening point and information on ingredients changed 1997 Oc Technologies B V The content of this safety data sheet is subject to the disclaimer on page 53 of this manual Oc 7050 7051 User Manual Safety data sheet Oc OPC Drum MATERIAL SAFETY DATA SHEET Number E 192 b UK 93 112 EEC and ISO 11014 1 Date July 1997 Page 1 of 2 Oc OPC Drum Part No 2912571 1 Product and company identification Product name Oc OPC Drum Part No 2912571 for Oc 7050 family Packing Cardboard box 2 Composition information on ingredients Ingredients CAS No Classification Weight Aluminium 7429 90 5 gt 99 Resins lt 1 Pigments lt 1 3 Hazards identification To our knowledge this product presents no health hazard in normal use 4 First aid measures Eyes contact Not Applicable N A Skin contact NA Inhalation NA Ingestion NA For any medical advice take along this material safety data sheet 5 Fire fighting measures Flash point C N A Not Applicable Explosion limits dust explosion LEL N A UEL N A n temperature C N A g media Dry chemical carbon
33. rely to the left or the right side 5 Reset the copy length counter to 0 by pressing the reset button see figure 7 7 Resetting the copy length counter 16 Oc 7050 7051 User Manual 6 Notice the direction arrow near the roll feeding knob Turn the knob in the direction of the arrow to feed out some copy material see figure 8 Note If you turn the knob in the wrong direction the copy material can slip out of the feeder see Inserting a new copy material roll on page 24 PET NG A 2 8 Turning the roll feeding knob 7 Hold the copy material in the middle and pull out material until the copy length counter shows the same length as the original as shown by the display on the operating panel Note Minimum length of the copy material is 420 mm Note You can turn the roll feeding knob to adjust the length of the copy material 8 Hold the copy material with one hand and move the cutter with your other hand entirely to the left or right side to cut the material 9 Feed the copy material into the copy feed table in accordance with the guidelines Start feeding the cutting edge and feed in line with the original see figure 9 on page 18 The copy will now be made Note The copy material is aligned in the nip of the rollers By inserting the material with an amount of slack the leading edge is aligned in the nip A delay between insertion of the material and the start of the tra
34. rial roll If the Oc 7050 7051 is equipped with the optional manual roll you can insert a new copy material roll as follows Y Inserting a new copy material roll 1 Pull open the drawer by using the two catches see figure 13 13 Opening the drawer section 2 If one of the rolls is still in use turn the roll feeding knob in the opposite direction of the arrow to let the copy material slip out of the feeder 3 If you want to use the other roll in the drawer simply feed in the material of that roll as described in step 11 on page 26 and on Note The front and the back roll do not have to be switched 24 Oc 7050 7051 User Manual 4 If you want to insert a new roll remove one of the roll holders from the drawer see figure 14 14 Removing the roll holder from the drawer section 5 Put a new roll on the holder as follows 6 Remove the empty roll from the roll holder while pressing the knob see figure 15 7 Slide the roll holder in the new roll of copy material while pressing the knob Note Keep the guide lines AO Al etc at the right side as shown in figure 15 15 Pressing the knob 8 Align the copy material roll with the appropriate lines on the roll holder while pressing the knob Materials 25 26 9 Reposition the roll holder with the copy material in the drawer see figure 16 10 Make sure that the cutter is moved entirely to the left or the right side
35. s Oc 7051 only After selecting trailing edge by pressing the display selection button you can use these buttons you add or remove a filing strip at the trailing edge varying between 40 to 100 mm in steps of 5 mm Oc 7050 7051 User Manual Switching on off After switching on the machine is ready for operation The display shows a moving spot In this state the operating panel is in stand by mode After you have switched on the machine there is no need to switch it off after each copy job You can leave the machine switched on for the rest of the day At all times the Oc 7050 7051 is ready for operation If the machine has been inactive for more than 2 minutes the operating panel returns automatically to the stand by mode The operating panel activates in the following situations you feed an original you feed a copy material a button on the operating panel is pressed v Switching on 1 Set the on off switch at the rear of the machine to position 1 see figure 1 If the mains is connected correctly the green switch will light up PE KEE SF 1 On off switch Note The machine is immediately ready for use v Switching off 1 Set the on off switch at the rear of the machine to position 0 see figure 1 Introduction 9 Dew Preventer optional If the Oc 7050 7051 is equipped with the optional manual roll a Dew Preventer can be install
36. s specified in Copy material that can be used on page 46 Avoid storing paper in rooms where temperature and humidity are high see Roomtemperature T and Relative Humidity RH on page 44 Also avoid dust and direct sunlight Wrap unused paper in plastic to prevent it absorbing moisture Oc 7050 7051 User Manual Making copies By feeding the original or the copy material the operating panel will go on and the copying process will start automatically When you have a copier which is equipped with a repeat function Oc 7051 you can make a maximum of 9 copies when feeding 1 original Note After 2 minutes of idleness the operator panel returns to the ready mode When you wait more than 2 minutes between two operations you have to restart the procedure v Making copies using cut sheet copy material 1 If required use the copy material selection button to select copying on paper or film 2 Select the desired number of copies by pressing the or button on the operating panel Oc 7051 only see figure 3 Note Changing the copy quantity can be done at all times When you make a mistake you simply press the correction button to correct the copy quantity x add toner Paperpath Oc 7051 correc stop ion 3 Setting more than one copy using the or button Copy jobs 13 14 3 Feed the original cent
37. the left cover and screw the knurled nut Switch on the copier Oc 7050 7051 User Manual Operator recoverable errors a BR GO ND ch When the copier detects an error the copier stops immediately The paper path indicator will lit and the length display shows an error code The following explains the general procedure in case of an operator recoverable error General procedure for operator recoverable errors Remove the original Open the manual copy material feed table Remove the copy material Check the paper path Close the manual copy material feed table The following table gives an overview of possible causes and specific actions Error messages Message Possible causes Specific actions E0 m Copy material is removed during Contact the key operator the copy process m Stop button has been pressed during a copy process m Original feed problem El Paper feed table is open Close paper feed table E2 Copy material is too short Contact the key operator Solving problems 39 Machine errors v Solving a machine error 1 Switch off the copier and check the complete paper path see page 35 and page 36 2 Then switch it on again If the operator panel shows no error indication you can continue copying If the machine error maintains then call the key operator 40 Oc 7050 7051 User Manual Oc 7050 7051 User Manual Appendix A Overview and tables Standard settings 42 On delivery t
38. ve the following safety rules Do not remove any screws from fixed panels m The copier is not user serviceable except for the components and maintenance materials mentioned in this manual Do not place any liquids on the copier a Use maintenance materials or other materials for their original purpose only Keep maintenance materials away from children Do not mix cleaning fluids or other materials a To avoid risks all modifications to Oc equipment are strictly reserved for Oc service personnel It is recommended to use only those copy control products that comply with inter national standards regarding product safety and radio frequency interference It is also recommended to use attachment cables specified by Oc a The copier has been fitted with an ozone filter If you have a maintenance contract the Oc service engineer will check this filter regularly and replace it if necessary Correct operation is guaranteed only if the filter is replaced by Oc a Do not move the copier yourself Contact your Oc Customer Service when you wish to move the copier If for some reason you have to move the copier yourself please make sure that the mains power point has the right fuse capacity See the Oc 7050 7051 safety data sheet in this appendix for information about fuses Do not bridge any mechanical or electrical circuit breakers Do not use an extension lead to connect the copier Locate the copier close to a wall s
39. waste toner bag from the holder and place the cap provided on the bag figure 20 20 Replacing the waste toner bag 9 Slide a new waste toner bag over the holder 10 Close the cover and tighten the knurled nut 11 Switch on the copier Materials 29 Cleaning the transparent platen If the transparent platen is dirty or static it should be cleaned to ensure top quality copies At the same time you can clean the white pressure platen Attention To achieve the best results we recommend the use of Oc cleaner A Codenr 1068117 Cleaner kit v Cleaning the transparent platen and the pressure platen 1 Switch off the copier 2 Open the top cover by pulling it towards you and raising the cover figure 21 21 Opening the top cover 30 Oc 7050 7051 User Manual 3 Clean the transparent platen and the white pressure platen with a soft cloth moistened with a small quantity Cleaner A For safety information see the safety data sheet in Appendix B 22 Cleaning the transparent platen and the white pressure platen Attention Make sure not to damage the actuator figure 22 located in the middle of the transparent platen 4 Close the top cover and push it back until you hear a click 5 Switch on the copier Materials 31 32 Oc 7050 7051 User Manual Oc 7050 7051 User Manual Chapter 4 Solving problems This chapter contains information on h
40. xplosion LEL U unknownUEL U Ignition temperature C Approx 500 Extinguishing media Dry chemical carbon dioxide water spray fog foam Special fire fighting precautions NA Hazardous products of decomposition NA Gi Accidental release measures Spills can be cleaned with a vacuum cleaner or a damp rag Do not use warm water because this makes the powder soft and sticky Handling and storage Keep bottle tightly closed to prevent dust formation Handle carefully Avoid breathing dust No special technical measures for storage Exposure controls personal protection No special technical measures No personal protective equipment needed Industrial hygiene after skin contact wash with cold water and soap Threshold Limit Value for nuisance dust 10 mg m Threshold Limit Value for carbon black 3 5 mg m continued on the next page Safety information 57 58 MATERIAL SAFETY DATA SHEET Number E 181 b UK 93 112 EEC and ISO 11014 1 Date July 1997 Page 2of2 Oc D1 Developer 9 Physical and chemical properties Appearance and odour Black powder faint odour Boiling point C N A Bulk density kg m Approx 2500 Vapour density air 1 N A Softening point C Approx 50 Solubility in water Insoluble Evaporation rate butyl acetate 1 N A Vapour pressure N A Volati 0 Other characteristics NA PH solution NA 10 Stability and reactivity Ther
41. ylene bottle contents 0 4 kg 0 89 Ib 2 Composition information on ingredients Ingredients CAS No Classification Weight Polyester resin 170831 75 1 50 100 Phenoxy resin PMN P 95 461 25 50 Carbon black 1333 86 4 5 10 Dye 15 Pigments lt 1 3 Hazards identification Ina toner dust cloud the formation of an explosive dust air mixture is possible Toner dust may cause discomfort for the eyes and respiratory tract in the same manner as inert nuisance dust To our knowledge with due observance of the recommended exposure limit and of normal hygiene this product presents no health hazard in normal use 4 First aid measures Eyes contact Rinse with plenty of water Skin contact Wash with cold water and soap Inhalation Clean nose mouth throat Cough up Fresh air Ingestion Rinse mouth with water If large quantity swallowed seek medical advice For any medical advice take along this material safety data sheet 5 Fire fighting measures Flash point C N A Not Applicable Explosion limits dust explosion LEL approx 60 g m UEL U unknown Ignition temperature C Approx 500 Extinguishing media Dry chemical carbon dioxide water spray fog foam Special fire fighting precautions NA Hazardous products of decomposition NA 6 Accidental release measures Spills can be cleaned with a vacuum cleaner or a damp rag Do not use warm water because this makes the powder soft and sticky 7
Download Pdf Manuals
Related Search