U s e r m a n u a l
Contents
1. Roksan Audio Itd ENGLISH Page 6 of 22 All specifications are liable to change without notice E amp OE SETUP SUMMARY XERXES 20 Placing the Xerxes 20 Prepare a level surface using a spirit level on which to place the Xerxes 20 absolute level is not critical as long as the surface is reasonably level If you wish to use a dedicated equipment support ensure that you get a vertically rigid table For best results it should sit rigid and level on a solid floor For the wall mounted turntable support ensure the same NOTE For best results use the Xerxes Upgrade Plinth Removing the Motor Transit Screw This screw prevents the precision motor and its bearing mount assembly from being damaged in transit Undo and remove this screw from the transit pillar to release the motor body With the screw in place the motor spring is in tension so be careful as the motor will rotate back to its normal operating position Please keep the motor transit screw safe in the packaging for future use Preparing the Main Bearing Remove the rubber plug on the main bearing Push a cotton Q tip down to the bottom of the housing and rotate it while gently pressing down Keep turning as you pull it out The cotton bud should now have a recess in its tip which shows that the precision ball bearing is correctly positioned at the bottom of the housing See figure From the small vial of oil pour 4 to 5 drops of oil into the bearing h2. Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 17 of 22 ENGLISH Clean the belt with a non alcohol wax based polish It is advisable to change the belt after every five years or after five thousand hours of use Clean the dust cover with a damp cloth as and when required The turntable is made of very high quality real wood veneer or high gloss lacquer and should be looked after with care It may be cleaned with a very soft cloth For any stubborn marks use a very slightly moistened lint free cloth Very little high quality furniture wood polish may be used every six to eight months DO NOT USE CLEANING AGENTS SOLVENT OR ABRASIVES I S N N R NR NIR di IN S IN N SS Ws N EE IN FR N SS S N SS eral DNI d A S PN A N NG AN EN Bearing Ball No Bearing Ball Impression Impression Refer to SETUP section above for detail on charging the Main Bearing with Roksan Supplied oil Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 18 of 22 ENGLISH INSTALLATION XERXES 20 Your Xerxes 20 is designed to work on a level light vertically rigid non resonant surface If the unit is to be on a floor mounted Hi Fi rack then ensure the rack is vertically rigid It is not as important if the rack is slightly compliant side ways Plea
3. Motor Pulley amp Inner outer platter alignment View from A BELT WOULD RI HIGHER ON THE IDE SLIGHTLY N THE PULLEY e 2 5mm A F ALLEN KEY View from B BELT WOULD RIDE SLIGHTLY HIGHER ON THE PULLEY Drive Belt Set up and Maintenance 2 Motor Pulley axis can also be aligned just as the Main Bearing Inner Platter axis See above 3 Ifthe levels are adjusted but the drive belt rides little too high then remove the belt and gently stretch it Wait a couple of minutes and refit the drive belt and the outer platter and check the running position again Repeat this process if necessary Roksan Audio Itd Xerxes 20 Record Player User Manual General Use Version 3 0 All specifications are liable to change without notice E amp OE Page 15 of 22 ENGLISH TRANSIT PILLAR MOTOR SPRING TRANSIT PILLAR MOTOR PAING GREW FIXING NUT BEARING UNSCREW amp REMOVE TRANSIT POSITION MOTOR AXIS A SMALL GAP OPERATION POSITION Motor Transit amp Operation Modes Always fit the transit screw if the unit is to be transported shipped There is no need to fit this screw if you are merely moving the record player or taking it in your car etc MOTOR FREE TO ROTATE ABOUT Roksan Audio Itd Xerxes 20 Record Player User Manual General Use Version 3 0 All specifications are liable to change without notice E amp OE Page 16 of 22 ENG
4. ROKSAN User manual ROKSAN AUDIO LIMITED 6 NORTHFIELD INDUSTRIAL ESTATE BERESFORD AVENUE ALPERTON MIDDLESEX HAO 1NW ENGLAND TEL 44 0 208 900 6801 44 0 208 900 6802 FAX 44 0 208 900 0734 www roksan co uk email info roksan co uk INTRODUCTION XERXES 20 Congratulations on your purchase of the ROKSAN Xerxes 20 Record Player This record Player is designed and manufactured to the highest specification and rigorously tested to offer you many years of trouble free pleasure Your Xerxes 20 is at the heart of your record playing system and the link between the tone arm cartridge and the record Its correct installation set up and operation will have a profound influence on the sonic performance of the entire record playing system Please read the contents of this manual thoroughly It will help you to understand your Xerxes 20 better and enhance your musical experience This manual is divided into the following sections Introduction Caution Design Setup Summary oetup Diagrams Installation Operation Troubleshooting Guarantee Specifications Notes UNPACKING Included in the packing of your Xerxes 20 Record Player you will find One Xerxes 20 Inner Platter One Xerxes 20 Outer Platter One Xerxes 20 Drive Belt One Xerxes 20 Spindle Cap One Vial of Xerxes 20 oil Cotton Bud amp lint free tissue One pair of cotton gloves One Xerxes 20 Dust Cover Set of Allen Keys 2 5 3 0 amp 5 0mm A F One inform
5. little Adjustment of these two screws will change the FRONT to BACK level So you need to check the front to back level after adjusting the left to right level See below Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 13 of 22 ENGLISH FRONT 2 5mm A F ALLEN KEY Use the 2 5mm A F Allen Key and looking from the left hand side adjust the back 3 screw to tilt the platter assembly FRONT to BACK as shown above DO NOT over tighten or slacken the fixing screw too much Adjustment of this screw will NOT change the LEFT to RIGHT level Belt riding position 1 mm gap between the Belt and the The Belt should ride with at lease Pulley flange 2mm clearance from the bottom of the Platt Ref Pulley flange thickness is 1mm LU NOTE e With the belt riding higher on the pulley i e more than 1mm gap the rotational speed would be slightly increased Drive Belt Set up and Maintenance 1 levels are adjusted but the drive belt rides a little too high then remove the belt and gently stretch it Wait a couple of With the belt riding lower on the pulley i e less than 1mm gap minutes and refit the drive belt and the outer platter and check the the rotational speed would be running position again Repeat this process if necessary slightly decreased Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 14 of 22 ENGLISH
6. the tonearm is designed as a reference platform to preserve the record cartridge interface from unwanted disturbances It has been computer modelled using finite element analysis to determine the optimum shape and of coupling of this platform to the bottom plinth The top plinth features the familiar cut out which was first seen on the original Xerxes that follows the contour of the sub plinth without touching The top plinth is connected to the bottom plinth via three suspension mounts The bottom plinth supports decouples and isolates the top and the sub plinths from external disturbances The motor is free to pivot on its own bearing on an axis of rotation coincident with the shaft of the motor With this unique dynamic system transient speed changes are absorbed and do not affect the measuring platform The armboard which provides another level of isolation is machined from a billet of Acetal with complimentary damping between the tonearm and the sub plinth The detachable armboard is fixed by three stainless steel bolts for easy tonearm mounting and adjustment The Bearing Platter Assembly At the heart of Xerxes 20 is Roksan s unique and formidable self centring self aligning true single point main bearing The innovative design of this bearing provides almost silent frictionless rotation precisely defining the rotational axis The bearing sleeve is gun drilled from solid phosphor bronze and honed to provide spindle bearing sleeve g
7. Day ROKSAN Retailer Name FE OCAUON Please keep a record for future reference Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 22 of 22 ENGLISH
8. LISH ARM BOARD FIXING SCREW ARM BOARD JE EUG TOP SUB PLINTH DO NOT PLINTH PULL OR PUSH ARM CABLE GRIPPED BETWEEN FOAM STRIPS BOTTOM PLINTH ARM CABLE PLATTER BEARING EARTH WIRE ARM CABLE GROUNDING SCREW LOOSE amp FREE Arm Cable Dressin Always ensure the arm cable is free and loose from the arm to the plinth as shown It is important that the sub plinth and the top plinth are free and not being pulled or pushed by the arm cable Note the Xerxes 20 has two foam strips fitted in the arm cable channel which can grip the arm cable and provide the necessary decoupling See above Please ensure the ground wire of the arm cable where applicable is attached securely to the platter grounding screw Maintenance The Xerxes 20 requires minimal user maintenance e The Main Bearing should be cleaned and recharged with Roksan Oil every 12 18 months Important to ensure the Main Bearing Ball is in the housing before recharging with oil See below e The motor pulley and inner platter should be cleaned every six to twelve months depending on frequency of use Both parts will periodically build up with small deposits of rubber where the belt runs around them Remove the centre piece felt mat outer platter and drive belt Clean the motor pulley and inner platter using alcohol or methylated spirit while they are still on the record player DO NOT EXERT EXCESSIVE PRESSURE as damage may occur
9. URFACE AND EDGE PRECISION MACHINED FOR FINAL SIZE AND ACCURACY COMPLETE INNER PLATTER LINEARLY DAMPED FREE OF ANY UNWANTED RESONANCE Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 4 of 22 OUTER PLATTER 1A SAW CUT FROM 12 SOLID ALUMINUM ALLOY BAR 2 PRECISION MACHINED TO SHAPE TUNED RESONANCE SAW CUT FROM 12 SOLID ALUMINUM ALLOY TUBE 4B PRECISION MACHINED TO SHAPE TUNED RESONANCE 5 RIM HEATED TO EXPAMD AMD CENTRE PART FITTED WHEN COOLED THE OUTER PLATTER PRECISION MACHINED FOR FINAL SIZE AND ACCURACY COMPLETE OUTER PLATTER LINEARLY DAMPED FREE OF ANY UNWANTED RESONANCE ENGLISH Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 5 of 22 Xerxes 20 Record Player User Manual General Use Version 3 0 ENGLISH 1004 a avisnrav S S D AN E anm 22 da idnooaa WOLLOS 22 401 a Ne ET ss 1S3 3 TGNIdS 1104 9SNIXI3 dOL LYASNI YVTIId YIHSVM SV Tid WVO4 1S3 YIAOD LSNA av Tlid 3INOHHO t gt HANITd YOLOW dOL Y 51109 AUVOA Wav 915 MAYS LNI3NLSNFAV 319NV LIL 915 MaYDS 8 NV Tlld LISNVS L YOLOIN aaLsnrav OL LON 5 ONINIVLSY YOLOW
10. ap of 2 10 000 along its length The only contact is between the polished spindle tip and the captive Tungsten Carbide super precision ball The spindle is made from hardened steel and is ground with a taper that locates into the inner platter without the use of adhesive or the need for pressing Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 3 of 22 ENGLISH The inner and outer platters are both machined from solid aluminium alloy instead of normal castings to ensure the material is homogeneous Each complete platter is constructed of two parts that are friction fitted together Each part is designed as a tuning fork and hence it s free from any nonlinearity Their natural frequencies are linearly damped as these two parts are joined together by friction only The platters are machined to extremely high tolerances to ensure roundness and balance Required inertia for a smooth and constant angular speed is achieved through high peripheral distribution of mass This maximizes inertia to mass ratio and reduces undue pressure on the bearing contact point It is this level of attention to detail throughout the design that ensures musical integrity INNER PLATTER TA 3B AB 5 6 SAW CUT FROM 6 127 SOLID ALUMINUM ALLOY BAR PRECISION MACHINED TO SHAPE TUNED RESONANCE CUT FROM 16 SVG ALUMINUM ALLOY PLATE PRECISION MACHINED TO SHAPE TUNED RESONANCE PLATE PRESS FITTED OM CENTRE BOSS AND ITS S
11. ated then the Sub plinth may require readjustment Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 10 of 22 ENGLISH NOTE Tonearm counter weight amp Platters must be fitted when checking level adjustments Sub plinth should be level with Top Plinth all the way round Fitting Drive Belt Outer Platter amp Level Adjustments Carefully place fit tone arm counter weight Carefully remove the motor transit screw place in a bag and store in the packaging carton for future use Remove the Drive belt from the bag and gently place it around the inner platter and the motor pulley Note The Xerxes 20 will perform better when the belt is not inside out and when it is the right way up To check for this consult Roksan Audio or your Roksan retailer distributor Remove outer platter from the bag and gently place it upside down Drive Belt Direction over the inner platter and seat it correctly on its recess To avoid To establish the correct belt marking tarnishing the platters use the cotton gloves provided Be direction try the belt inside out extra careful to ensure the platter does not slip through id hands as this could seriously damage your record player Mc CONN ANG Check the alignment of the sub plinth against the top plinth by looking at the level all the way round If necessary realign the sub plinth see below flows better Check the alignment of the motor pulle
12. ation pack and warranty card After removing these items please retain all packing materials Correct packing is necessary for future transportation of your Xerxes 20 Record Player MAINTENANCE After switching the amplifier off and placing the stylus guard on the record player may be cleaned with a lightly dampened soft cloth or a soft brush Avoid using abrasives or solvents Take care not to damage the cartridge stylus or the tone arm e The Main Bearing requires recharging with oil every 12 18 months SEE BELOW Drive belt requires cleaning with a wax based furniture polish every 12 18 months SEE BELOW Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 2 of 22 ENGLISH CAUTION XERXES 20 The Xerxes 20 Record Player incorporates several unique design features and manufacturing techniques It is important to observe the following to avoid any damage and to ensure optimum performance IMPORTANT DO NOT attempt to run the record player without Main Bearing Oil Careful when placing the Inner Platter Careful when placing the Outer Platter onto the Inner Platter Outer Platter should not hit the Motor Pulley or drop onto the Inner Platter DESIGN XERXES 20 The Structure As with the original TMS turntable design the Xerxes 20 has three separate plinths used for decoupling across a selective frequency band The sub plinth which carries the main bearing platter assembly and
13. ation position Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 7 of 22 ENGLISH Fitting the Tonearm You will need to follow the tonearm manufacturer s instructions as most tonearms differ slightly in their methods of fixing Connecting the Arm Cable Use a standard type arm cable preferably the ROKSAN 5 pin Din High Definition Tonearm Cable This must either be freely dressed in between the foam strips or fixed securely to the bottom plinth using cable ties See figure It is important that the arm cable is loose free between the arm and plinth The foam strips or the cable ties Otherwise this will restrict the movement of the sub plinth arm board and interfere with the decoupling isolation of Xerxes 20 Fitting the outer platter Remove the outer platter from its plastic bag Gently place the outer platter on the inner platter the recess on the inside locates onto the plate of the inner platter Take care not to hit the motor pulley with the rim of the outer platter Fitting the Mat The Xerxes 20 is supplied with the Roksan Rmat 5 which is designed to provide optimum contact between the record and the platter assembly It fits over the main bearing spindle in the centre and rests uniformly over the platter surface The Centre Piece Spindle Cap Roksan introduced this unique removable centre piece with the original Xerxes Slide the centre piece over the bearing spindle to ass
14. authorised ROKSAN retailer If equipment returned for repair to ROKSAN is found on inspection to comply with the product specification ROKSAN reserves the right to make a charge for examination and return carriage Unauthorised servicing will void this guarantee Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 20 of 22 ENGLISH SPECIFICATIONS XERXES 20 Main Bearing Spindle Hardened tool steel Roundness amp Concentricity 5 Microns Length to Diameter ratio 11 1 Main Bearing Ball Super precision Tungsten Carbide Roundness lt 1 Micron Diameter 2mm Main Bearing Housing Solid Phosphor Bronze Clearance 2 1 0000 Inner Platter 2 Piece Solid Aluminium alloy Interference fitted non resonant Outer Platter 2 Piece Solid Aluminium alloy Interference fitted non resonant otructure 3 Plinth Design Isolation 3 Level De coupling Motor Custom made 24 pole synchronous Pulley oolid Aluminium alloy Roundness amp Concentricity lt 1 Micron Drive Belt Precision ground Neoprene Motor Mount Unique synchronizing bearing Motor Drive External speed controller Wow amp Flutter 0 02 Rumble 80dB Dimensions 450 x 370 x 115mm Weight 12 Kg Et ss Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 21 of 22 ENGLISH NOTES XERXES 20 Xerxes 20 Record Player Serial Number Purchase Date Year 2 Month
15. helf manufacturer s instructions but do ensure good mechanical integrity of the structure on which your Xerxes 20 is to be sited NOTE For best results use the Xerxes Upgrade Plinth Consult your Roksan distributor retailer or Roksan Audio if you have any queries OPERATION XERXES 20 owitch on the dedicated Xerxes Power Supply and choose the desired speed The platter should start turning Place the record on the mat ensuring the centre piece is in place When the record is on the platter remove the centre piece and place it in spindle cap rest on the top plinth When you are not using the record player either leave the Xerxes Power Supply on but in standby or switch it off completely Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 19 of 22 ENGLISH TROUBLESHOOTING XERXES 20 If you suspect that your ROKSAN Xerxes 20 Record Player is not operating properly first check all the connections carefully Below are some likely encountered problems with suggestions for possible cure The list is not exhaustive If you have any unresolved problems please consult your appointed ROKSAN dealer or distributor SYMPTOM LIKELY CAUSE SUGGESTED REMEDY Platter not turning Motor drive lead not inserted properly Ensure Motor drive lead is fully inserted Motor drive not switched on Switch Motor drive on Drive belt not fitted Fit drive belt and try again Start up too slow gt 70sec Motor locked in transit p
16. il Wear the cotton gloves and remove the Inner Platter from its bag use the Lint Free Tissue and gently clean the Inner Platter Spindle free from any dirt Gently place the Inner Platter Spindle into the Main Bearing and allow it to settle down Due to very tight tolerances the Inner Platter will take some time to settle down oll 00000 i 4 p 4 1 45 f E Roksan Audio Itd Page 9 of 22 ENGLISH All specifications are liable to change without notice E amp OE Fitting Pickup Arm and Phono Cartridge Use the 3mm A F Allen key and remove the Acetal arm board Carefully fix the Phono cartridge to the head shell following manufacturer s instructions Carefully mount the Pickup arm to the arm board following manufacturer s instructions do not fully tighten the arm to the arm board allowing for later adjustments Remount arm board tightening the Allen bolts fully if required support the arm board from underneath while tightening the bolts Plug in the pickup arm cable connector and check that the sub plinth assembly is free Ensure the gap around the Sub plinth is even if necessary gently lift the Sub plinth and reposition it IMPORTANT NOTE The Xerxes 20 sub plinth alignment is factory set according to the cutout on the arm board e g Artemiz cut is set for the Artemiz tone arm weight etc If the tone arm to be fitted is heavier or lighter than the one anticip
17. ist placing the record centrally on the mat Before playing the record the centre piece can be removed to eliminate any direct mechanical contact between the record and the main bearing spindle The only contact would be through the mat and the stylus It is important to note that IMPORTANT Use of any clamp directly connects the vinyl to the structure and allows unwanted noise to be immediately present in the vinyl and thus picked up by the stylus Do not use any record weights as this may permanently damage the Main Bering Connecting the Power Supply The dedicated turntable power supply is connected to the rear of the turntable using the 5 pin connector Always connect the power supplies before switching it on n Operation Switch on the dedicated Xerxes Power Supply and choose the desired speed The platter should start turning Place the record on the mat ensuring the centre piece is in place When the record is on the platter remove the centre piece and place it in spindle cap rest on the top plinth Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 8 of 22 ENGLISH SETUP DIAGRAMS XERXES 20 Fitting the Inner Platter Pull out the Main Bearing Plug and place it in the Oil Vial bag Carefully clean the Main Bearing with one of the Cotton Buds and check that there is a ball impression on the tip Remove the oil vial cap and charge the Main Bearing with 4 to 5 drops of Roksan supplied O
18. osition Remove motor transit Belt dirty or sticky Clean belt with wax based furniture polish Main bearing dry Check if no damage to bearing recharge with Roksan main bearing oil see above Main bearing ball missing Check if no damage to bearing fit new Xerxes 20 main bearing ball if in doubt consult your Roksan retailer Belt falling off Incorrect motor alignment Check and realign motor see above Platter touching the plinth Incorrect main bearing alignment Check and realign bearing see above GUARANTEE XERXES 20 There are no user serviceable parts on your Xerxes 20 Record Player If a fault should develop refer any servicing to your appointed ROKSAN dealer distributor or approved service agent Your ROKSAN Xerxes 20 Record Player is guaranteed against any defect in materials and workmanship for a period of two years from the date of purchase This guarantee only becomes effective if the warranty card is validated by the ROKSAN retailer from whom the equipment was purchased and returned to ROKSAN within 28 days of purchase This guarantee excludes 1 Damage caused due to accident misuse neglect and incorrect installation adjustment or repair 2 Liability for damage or loss during transit from the retailer or purchaser to ROKSAN or its authorised distributor for the purposes of repair or inspection Carriage costs to ROKSAN shall be borne by the consignor All claims under this guarantee must be made through an
19. ousing Always replace the plug to keep the bearing housing clean if you are not fitting the inner platter immediately IMPORTANT Always use ROKSAN supplied Main Bearing Oil Placing the Inner Platter Remove the inner platter spindle assembly from its plastic bag The spindle is slightly oiled to protect the tool steel spindle remember to do the same if you are storing your Xerxes for a length of time Wipe the oil from the spindle using a soft lint free tissue Remove the plug from the bearing and carefully guide the spindle into the main bearing hole Gently spin the inner platter The platter will slowly sink over a period of about ten to twenty minutes Do not force the platter down The spindle is factory fitted to ensure that the inner platter runs true Take extra care not to knock or bend the spindle You can check that the inner platter has settled by gently raising and lowering the spindle by about 3mm You should hear a quiet metallic click as it touches the ball bearing If there is enough oil a ridge will be visible at the top of the bearing housing If you do not see a ridge use one more drop of oil Fitting the Belt The belt should be wiped with a non alcohol wax based polish i e aerosol type such as Pledge before fitting When this has been done the belt can then be fitted around the inner platter and motor pulley Turn the inner platter by hand for a few revolutions and the belt will come to rest in its correct oper
20. s are liable to change without notice E amp OE Page 12 of 22 ENGLISH The Inner Platter is factory aligned and should be level with the sub plinth Carefully place the outer platter the right way up on the inner platter and observe the gap between the under side of the outer platter and the top surface of the sub plinth First look from the front of the record player and then from the side The alignment of the platter is achieved by adjusting the Main Bearing fixing screws There are 3 fixing screws and tightening slackening these will tilt the axis of the main bearing and hence the platter level Platter level adjustment ensures correct azimuth between the platter record and tonearm head shell INCORRECT AZIMUTH CORRECT AZIMUTH INCORRECT AZIMUTH If any adjustment is required you must first adjust the LEFT to RIGHT and then the FRONT to BACK See below PLEASE NOTE THE FIXING BOLT HEADS ARE NOT VISIBLE FROM THE SIDE GAP LEFT HAND SIDE RIGHT HAND SIDE 9 0 2 5mm A F ALLEN KEY TOP PLINTH Use a 2 5mm A F Allen Key to adjust the Main Bearing Fixing Screws Looking from the front adjusting the front two screws will tilt the platter assembly LEFT to RIGHT as shown above DO NOT over tighten or slacken the fixing screws too much Correct tension is to have the screws tightened by 1 1 5 turn after they have come into contact with the sub plinth So when adjusting slacken one a little and tighten the other a
21. se ensure the surface on which the record player is to be placed is reasonably level Remember the type of shelf material can significantly affect the performance of any Hi Fi equipment especially record players Please ensure this surface is as rigid and as non resonant as possible Note It is not necessary to have this surface over damped with sound absorbent material Note the Xerxes 20 feet are adjustable and they are attached to the lower decoupling domes and thus are part of the structural suspension of the unit These can be used to fine tune the level of the record player but they must not be at an angle tilted to the side Your Xerxes 20 works much better when its feet are straight and upright It is equally important to ensure the arm cable and the motor drive lead are not pulling or pushing the record player plinth Otherwise they will act as feed back channels and also tilt the record player slightly and thus move the feet out of their upright position Take care when dressing these cables to avoid mechanical strain and remember not to run these alongside mains power or speaker cables Foot straight amp upright ra ICE TE UC UAE Iu RIED Me RAE dts NS dl s E i RANT M eg RET a EX a bu sr d d zs rg i r E c T d Pu T E x Eon F Pre t If the unit is to be used on a wall mounted shelf please ensure the same In either case follow the rack s
22. y against the inner outer platter by looking in the directions A amp B View the Top edge and the Flange of the pulley to see if it is level with the inner outer Motor Pullev amp Inner outer platter platter for this adjustment see instructions below alignment each time listen to find out which way round the music View from B View from A Roksan Audio Itd All specifications are liable to change without notice E amp OE Page 11 of 22 ENGLISH NOTE TILT ADJUSTMENT SCREW IS UNDER THE INNER PLATTER Plinth Assembly Tilt Adjustment 1 Gently tighten or slacken fixing bolts 1 amp 4 accordingly using the 5mm A F Allen key to adjust the level of the Sub plinth Inner Platter about the axis A Check that the Inner Outer Platter assembly is level with the Pulley See view from A above Gently tighten or slacken Tilt adjustment screw T using the A F Allen key to adjust the tilt of the Sub plinth Inner Platter about the axis B Check that the Inner Outer Platter assembly is level with the Pulley See view from B above NOTE Use a small light spirit level to check relative levels if necessary TILT ADJUSTMENT ABOUT AXIS A TILT ADJUSTMENT ABOUT AXIS B The Sub plinth should be level with the Top Plinth Check the level all the way round If necessary realign the sub plinth Roksan Audio Itd All specification
Download Pdf Manuals
Related Search