Installation and Assembly: Wireless Articulating Arm - Peerless-AV
Contents
1. peerless V gt IG SS cr oee III Wireless Articulating Arm Wall Mount for 42 to 60 Flat Panel Installation and Assembly Displays Model WL SA761PU 200 Maximum Load Capacity 130 lbs 59 kg e 800 865 2112 Fax 800 359 6500 www peerless av com 2300 White Oak Circle Aurora Il 60502 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Note Read entire instruction sheet before you start installation and assembly A WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings for US customers please call Peerless customer care at 1 800 865 2112 for all international customers please contact your local distributor This product should only be installed by someone of good mechanical aptitude has experience with basic building construction and fully understands these instructions Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Never exceed the Maximum Load Capacity See page one If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment2. Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holding power This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury This product was designed to be installed on the following wall construction only WALL CONSTRUCTION HARDWARE REQUIRED Wood Stud Included Wood Beam Included Solid Concrete Included Cinder Block Included Metal Stud Contact Qualified Professional Brick Contact Qualified Professional Other or unsure Contact Qualified Professional Tools Needed for Assembly e stud finder edge to edge stud finder is recommended e phillips screwdriver e drill e 3 16 5mm drill bit for wood studs 3 8 10mm drill bit for concrete e level e 7 16 open end wrench Table of Conten BAUS BUS oct erecta taps er eect EE ere te atic on als ret carmrns EEE este ie nse e E E E AE 3 4 MU MISE aN cepts reece ae pects rept EEEE EE EENE sie A Sacto septs Me aes eae ET 6 7 Wireless Receiver Assembly and Power Module Assembly Installation cccccsccceceeeeesseeeeseeeeeseeeeeeeaeeeeseeeessaeeeesaeees 9 15 Wireless Receiver Assembly and Power Module Assembly Setup cccccccccsecceeeeeseeeesaeeeeeeeeeeceeeeeaeeeeseaeaeeeeeaeaeeeessaaes 16 Mounting Flat Panel Display er cdoettccrrre to eats erpendarnsc reali erord asennad peed enaar eaaa iaia dadi ia hadaa oles nants sda baleen a eaihedmnnes
3. 76mm Insert anchors D into holes flush with wall as shown right Place wall arm over anchors and secure with 5 16 x 3 screws C Level then tighten all fasteners A WARNING e Tighten screws so that wall plate is firmly attached but do not overtighten Overtightening can damage screws greatly reducing their holding power V ae T D eaei C3 Never tighten in excess of 80 in Ib 9 N M WLLL Always attach concrete expansion anchors directly to load bearing concrete Tighten all fasteners Never attach concrete expansion anchors to concrete covered with plaster drywall or other finishing material If mounting to concrete surfaces covered with a finishing surface is unavoidable SOLID CONCRETE the finishing surface must be counterbored as shown below Be sure concrete anchors do not pull away from concrete when tightening screws If plaster drywall is thicker than 5 8 16mm custom fasteners must be supplied by installer A CINDER BLOCK INCORRECT CORRECT C a e EPA ao N o conerelg concrete O oO gt To g E z o a Pann O 4 0 Lat AP orgies red ies A ogee pe r 5 5 plaster Q O plaster 3 O Ay drywall m zi drywall 4 a ai N BT po SN o Y 0 O 7 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Adapter Bracket Adjustment NOTE If display has
4. SLIDE PLATE oe DETAIL 1 5 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Installation to Double Stud Wall A WARNING e Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Tighten wood screws so that wall plate is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in lb 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Installers are responsible to provide hardware for other types of mounting situations Use a stud finder to locate the edges of the studs and draw a vertical line down the center of each stud Determine and mark the desired display center on the wall Place wall plate template wall arm on wall with top mounting slots 9 229mm above desired display center as shown in figure 2 1 Level wall plate template wall arm on wall and mark center of four mounting holes making sure that the mounting holes are on the stud centerlines Drill four 3 16 5mm dia pilot holes to a depth of 3 76mm Attach wall arm A to wall using four wood screws C as shown in fig 2 2 Level wall plate then tighten all fasteners W
5. not included into the tripe tap HDMI shown into the wireless receiver grounded outlet COMPONENT CABLE Cable Management NOTE Make sure extension cord not included has Snap wall plate covers F to top and bottom of 22 enough slack to allow full movement of the arm wall plate rails as shown Run extension cord not included through top or bottom of arm A Lock cables into place by snapping cable covers J amp K onto mount as shown Display may have to be moved for easy access S PLATE RAIL Optional If additional cable management is required route cable ties G through slots of arm A as shown in detail 8 DETAIL 8 21 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Arm Tension Adjustment A WARNING e Do not remove screw or loosen screw until it is no longer engaged with the mount Doing so may cause the display to fall e If screws become loose over time tighten screws as necessary Tighten screws to 50 in Ibs 5 6 N m maximum torque lf more or less tension is desired in the arm pivot points do the following e To increase tension turn socket screw clockwise with 5mm allen wrench I NOTE Tighten screws to 50 in Ibs 5
6. 20 1027 M5 x 95mm 4 M6x 12mm 4 520 9543 520 1128 a I D 22 4 540 ee S M6 x 30mm 4 M8x16mm 6 M8 x 25mm 4 M8 x 40mm 4 I D 34 4 multi washer 6 510 9109 520 9257 520 1031 520 1136 540 1059 580 1036 wireless transmitter 1 vga to rca adapter 1 plastic stand 1 remote 1 install guide 1 180 1202 180 1006 180 1205 180 1207 LIT 0905 3v battery 1 12v power adapter 1 ir flasher 1 hdmi cable 2 instruction sheet 1 180 0008 180 1004 180 1009 600 0234 180 9023 4 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Optional Horizontal Adjustment of Wall Arm on Wall Plate NOTE If mounting wall arm A to wood stud walls slots on wall plate must align to wood studs Determine desired location of display center detailed in step 2 Measure the distance from the center of wall arm A to desired display center Loosen four 1 4 20 x 17mm screws using 5mm allen wrench I Slide wall arm assembly 4 1 2 to the left or right as shown in figure 1 1 NOTE Align bevels dots of slide plate with bevels dots of wall plate rails as shown in detail 1 then retighten 1 4 20 x 17mm screws Do not adjust arm while display is attached Skip to page 6 for Wood Stud Installation Skip to page 7 for Concrete and Cinder Block Installation 1 4 20 X 17MM SCREWS WALL PLATE r a a ae ee ee EO ANZN DEA ee ee ZS _ t2 WALL PLATE RAIL
7. 5mm allen wrench I as shown in figure 7 1 Reinstall four 1 4 20 self tapping screws to secure display brackets to inner set of mounting holes on universal adapter bracket B as shown in figure 7 2 OUTER MOUNTING INNER MOUNTING 1 4 20 SELF TAPPING SCREWS 1 4 20 SELF TAPPING SCREWS y fig 7 1 To prevent scratching the display set a cloth ona flat level surface that will support the weight of the display Place display face side down and place universal adapter bracket B onto display 12 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Loosely attach the large enclosure mounting bracket 7 3 Loosely attach the large enclosure mounting E T on the power module assembly N with two 1 4 bracket T on the wireless receiver assembly M 20 decorative screws Q and two 1 4 20 nuts R as with two 1 4 20 decorative screws Q and two shown NOTE The enclosure mounting bracket can 1 4 20 nuts R as shown NOTE The enclosure be installed with the inside notch facing downward if mounting bracket can be installed with the inside additional side to side adjustment is needed notch facing downward if additional side to side adjustment is needed 7 4 Align one display bracket with one set of display mounting holes Place spacers between display bracket and display Place the enclosure mounting brackets T open end of notch facing downward between the display bracket and spacers Begin with the longest l
8. 6 N m maximum torque e To reduce tension turn socket screw counter clockwise with 5mm allen wrench I NOTE Do not turn more than half a turn TENSION SCREW lh Ni ames TENSION SCREWS 2 5 Plug extension cord into power source To complete the installation of your wireless mount please refer to the HD Flow User s Manual and the HD Flow Install Guide included 22 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 2012 Peerless Industries Inc Peerless AV is a registered trademark of Peerless Industries Inc All rights reserved All other brand and product names are trademarks or registered trademarks of their respective owners LIMITED WARRANTY Peerless Industries Inc Peerless AV warrants to original end users of Peerless AV products that Peerless AV products will be free from defects in material and workmanship under normal use for the periods listed below from the date of purchase by the original end user At its option Peerless AV will repair or replace with new or refurbished products or parts or refund the purchase price of any Peerless AV product which fails to conform with this warranty In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable express warranty set forth above Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not
9. ARNING e Do not lift more weight than you can handle Use additional man power or mechanical lifting equipment to safely handle placement of the display e Do not tighten screws with excessive force Overtightening can cause damage to mount Tighten M10 x 15mm screws E to 40 in Ib 4 52 N M maximum torque Mounting Flat Panel Display Hook M10 x 15mm screws into keyslots of wall arm adapter plate A as shown figure 17 1 DISPLAY NOT SHOWN FOR TE Insert two M10 x 15mm screws E into bottom holes of adapter plate as shown in figure 17 2 Tighten all fasteners with 6mm allen wrench H DISPLAY NOT SHOWN FOR CLARITY PLATE fig 17 2 19 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Adjustment of Flat Panel Display A WARNING e M10 x 15mm screws E must be securly tightened before changing orientation of wall arm assembly A Failure to lock adapter bracket can cause display to come off of mount 18 FOR PORTRAIT OR LANDSCAPE DISPLAY ORIENTATION Remove two M5 x 12mm screws one M5 x 6mm screw and rotation block from top of tilt head as shown in top view and rear view Gently grasp sides of display and rotate display into portrait or landscape p
10. Neaaad 20 Cable Managemeni eee eee eee eee ere ee eee aa a a aed aara a a eee ee eee 22 2 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Before you begin make sure all parts shown are included with your product Parts List r ACc TOY ITAMWIO OIOO D M N O P Q Description wall arm assembly universal adapter bracket wood screws concrete anchors M10 x 15 mm socket head screw wall plate cover cable tie 187 x 7 5 Ig 6 mm allen wrench 5 mm allen wrench rear cable cover front cable cover 4 mm allen wrench wireless receiver assembly power module assembly cable management sheath cable tie 04 x 5 75 lg decorative screw 1 4 20 lock nut 1 4 20 enclosure mounting bracket small enclosure mounting bracket large cable tie anchor yD S ee O o Be o fees n fe fee o Be WL SA761PU 200 Part 095 P 1992 095 P1635 2 920 1243 990 0321 520 9262 590 1325 990 1168 960 9716 960 9640 590 P1326 590 P 1327 960 9646 180 1092 180 1015 990 9468 960 9711 920 2325 930 1021 1205195 120 1196 590 9469 2 2 am e eccer eef Vi V7 y ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Adapter Bracket Fasteners M5 x 12mm 4 504 9013 5
11. OOD STUD WOOD STUD gt Oe L A A OTO CS CENTER OF DISPLAY fig 2 1 6 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Installation to Solid Concrete or Cinder Block A WARNING e When installing Peerless wall mounts on cinder block verify that you have a minimum of 1 3 8 35mm of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 25mm minimum from the side of the block Cinder block must meet ASTM C 90 specifications It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity e Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor e Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components D Determine and mark the desired display center on the wall Place wall plate template wall arm on wall with l Sa top mounting slots 9 229mm above desired display center as shown in figure 2 1 Level wall plate template wall arm on wall and mark center of four mounting holes making sure that the mounting holes Drill four 3 8 10mm dia pilot holes to a depth of 3
12. PLAY BRACKETS Y Y NOTE X dimensions should be equal Y dimensions should be equal 10 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 NOTE Wireless Receiver and Power Box removed for clarity Begin with the longest length screw hand thread screw through multi washer display brackets B and spacer in that order into display as shown below Screw must make at least three full turns into the mounting hole and fit snug into place Do not over tighten If screw cannot make three full turns into the display select a shorter length screw from the baffled fastener pack Repeat for remaining mounting holes level display brackets and tighten screws Center display brackets horizontally and vertically on back of display Tighten two 1 4 20 x 1 25 screws Reinstall four 1 4 20 x 6 screws using 5mm allen wrench I into appropriate fixed stop position from chart on page 8 DISPLAY L PACER N F ie 1 4 20 x 1 25 SCREWS 1 4 20 x 6 SCREWS 11 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Wireless Receiver and Power Module Installation VESA 200 x 200 or VESA 200 x 100 Mounting Pattern lt a Remove four 1 4 20 x 6 screws using 5mm allen wrench SYS BN x 1 25 SCREWS I and loosen two 1 4 20 x 1 25 screws 1 2 turn to allow for display bracket adjustment 7 1 Remove four 1 4 20 self tapping screws to detach display brackets from outer mount holes of universal adapter bracket B using
13. a VESA 400 horizontal mounting pattern skip to step 4 on page 9 NOTE For VESA 200x200 or VESA 200x100 mount hole patterns skip to step 5 on page 12 1 4 20 x 1 25 SCREWS 3 J Remove four 1 4 20 x 6 screws using 5mm allen wrench I and loosen two 1 4 20 x 1 25 screws 1 2 turn to allow for display bracket adjustment To prevent scratching the display set a cloth on a flat level surface that will support the weight of the display Place display face side down and refer to display manufacturers instructions for removing obstructions from the back of the display Adjust display brackets to align with display mounting holes Measure horizontal mounting hole pattern and choose fixed stop position from chart below horizontal mounting hole pattern fixed stop position 10 3 4 16 1 16 273 408 mm FIXED STOP POSTION 3 FIXED STOP POSTION 2 FIXED STOP POSTION 1 CO A ey OO gt OOIE J ITST gt COOOOC 5 C lt 8 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Wireless Receiver Assembly and Power Module Assembly Installation NOTE The Wireless Receiver Assembly and Power Module Assembly position c
14. an be interchanged based on the display s connector panel location Install Wireless Receiver Assembly on the side closest to the connector panel O Loosely attach the small enclosure mounting brackets S on the wireless receiver assembly M with two 1 4 20 decorative screws Q and two 1 4 20 nuts R as shown in fig 4 1 NOTE The enclosure mounting bracket can be installed with the inside notch facing downward if additional side to side adjustment is needed Attach the mounting brackets S open end of notch facing downward to the left display bracket with two 1 4 20 decorative screws Q and two 1 4 20 nuts R as shown in fig 4 2 Position the wireless receiver assembly approximately 1 4 from the universal adapter as shown in detail 2 Once in position tighten the four 1 4 20 decorative screws Q using 4mm allen wrench L DETAIL 2 DISPLAY BRACKET INSIDE NOTCH fig 4 1 Loosely attach the enclosure mounting brackets S on the power module assembly N with two 1 4 20 decorative screws Q and two 1 4 20 nuts R as shown in fig 5 1 NOTE The enclosure mounting bracket can be installed with the inside notch facing downward if additional side to side adjustment is needed Attach the mounting brackets S open end of notch facing downward to the right display bracket with two 1 4 20 decorative screws Q and two 1 4 20 nuts R as shown in fig 5 2 Position the power module assembly approximately 1 4 from the universal a
15. apply to you This warranty does not cover damage caused by a service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless AV b the failure to utilize proper packing when returning the product c incorrect installation or the failure to follow Peerless AV s instructions or warnings when installing using or storing the product or d misuse or accident in transit or otherwise including in cases of third party actions and force majeure This warranty also does not cover corrosion or rust resulting from damaged scratched or chipped paint or other surfaces In no event shall Peerless AV be liable for incidental or consequential damages or damages arising from the theft of any product whether or not secured by a security device which may be included with the Peerless AV product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty is in lieu of all other warranties express or implied and is the sole remedy with respect to product defects No dealer distributor installer or other person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless AV in connection with the sale of any Peerless AV product This warranty gives specific legal rights and you may also have other rights which vary from state to state Product Warranty Period M
16. dapter as shown in detail 2 Once in position tighten the four 1 4 20 decorative screws Q using 4mm allen wrench L DISPLAY BRACKET Wes gt D Seh fig 5 2 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Installing Adapter Brackets to Display A WARNING e Tighten screws so display brackets are firmly attached to display Do not tighten with excessive force Overtightening can cause stress damage to screws greatly reducing their holding power and possibly causing screw heads to become detached Tighten to 40 in lb 4 5 N M maximum torque e If screws don t get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly secured damage may occur to display or product may fail Select the screws from the baffled fastener pack that best fit your display and secure to display following step 6 3 Q or 6 4 on page 11 NOTE Top and bottom mounting holes must be used for attaching display brackets Middle holes should also be used where the fasteners and displays allow Verify that all holes are properly aligned then tighten screws using a phillips screwdriver CENTER DISPLAY BRACKETS VERTICALLY AND HORIZONTALLY ON BACK OF DISPLAY DIS
17. ength screw hand thread screw through the multi washer display brackets enclosure mounting brackets T and spacer into display as shown Screw must make at least three full turns into the mounting hole and fit snug into place Do not over tighten If screw cannot make three full turns into the display select a shorter length screw from the baffled fastener pack Center display brackets vertically Position the enclosure mounting brackets T horizontally making sure that the notch in the brackets are seated on the screws Tighten screws MULTI WASHER SPACER DISPLAY BRACKET 13 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 7 5 Slide universal adapter bracket B to the opposite side and align second display bracket with second set of display mounting holes Hand thread screws through the multi washer display brackets enclosure mounting brackets T and spacer into display as shown Tighten all screws SCREW MULTI x WASHER SPACER DISPLAY BRACKET Center universal adapter bracket B horizontally on back of display as shown in figure 7 3 Tighten two 1 4 20 x 1 25 screws Reinstall four 1 4 20 x 6 screws using 5mm allen wrench I into fixed stop position 1 as shown in figure 7 4 1 4 20 x 1 25 SCREWS FIXED STOP POSITION 1 WITH 1 4 20 x 6 SCREWS fig 7 4 14 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 7 7 Position the wireless receiver assembly M and power module assembl
18. oiled cord back inside of the enclosure fig 10 2 IR RECIEVER IR RECIEVER fig 10 1 16 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Close the top cover of the wireless receiver enclosure making sure that the IR receiver cord runs underneath the cable opening as shown in figure 11 1 Re install the two 8 screws AS 8 SCREWS CABLE OPENING Install the cable tie anchor U onto the inside back Plug the power cord from your display into the triple wall of the power module assembly N Remove the tap grounded outlet as shown Coil up the excess adhesive backing from the anchor and press into cord and secure with a cable tie G inserting it place in the area shown through the cable tie anchor U and around the coiled cord TAP D Close the top cover of the power module assembly 15 Place the cords inside the cable management sheath N making sure that the power adapter cords run O by pushing the cables through the slit in the underneath the cable opening as shown below sheath NOTE The sheat may need to be trimmed Re install the M5 x 10mm phillips screws to length before installing cords M5 x 10mm SCREWS CABLE OPENING ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Position the cable management sheath and secure with two cable ties in the approximate locations shown below and detail 7 Do not overtighten cable ties 18 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 A W
19. osition as shown in figure 18 1 and reinstall rotation block with two M5 x 12mm screws and one M5 x 6mm screw NOTE M5 x 6mm screw required in landscape orientation only ATA M5 X 12MM SCREWS T TOP VIEW Cf ff 7 I Oo CAS A lA a Y Seo ZS yO A ly TILT Adjustment Adjust tension knob on side of mount to desired tension to enable tilt adjustment and balance your display size and weight Push or pull from top or bottom of display to adjust tilt as shown The tilt can be adjusted to a maximum of 10 forward or 5 backward Retighten tension knob NOTE For larger displays tension screw on opposite side of mount may need to be tightened using 5 32 allen wrench L ROLL Adjustment Rotate display 5 clockwise or counter clockwise level display then tighten M5 x 10mm screws as shown in detail 8 FOR VERTICAL HEIGHT ADJUSTMENT Tighten or loosen M8 x 40mm screws to achieve 1 of vertical height adjustment as shown in detail 7 NOTE M8 x 40mm screws must be turned an equal number of times CAUTION e Do not tighten screws with excessive force e Be careful not to pinch fingers when opening and closing mount from the wall 20 of 23 M5 X 12MM Foo POTS TENSION KNOB M8 X 40MM OLANA scREWS DETAIL 7 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Plug the component cable s from your display Plug extension cord
20. ounts 5 years Furniture 1 year Cables 25 years Cleaning Products 1 year Electronic Products and components 1 year IN A vi Sal peer ess ANv www peerless av com 2012 Peerless Industries Inc 23 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12
21. y N approximately 1 4 from the universal adapter B as shown Once in position tighten the four 1 4 20 decorative screws Q using using 4mm allen wrench L and a 7 16 open end wrench Skip to step 8 Wireless Receiver Assembly and Power Module Assembly Setup Remove the two 8 screws securing the cover of the wireless receiver assembly as shown in detail 3 Open the enclosure to expose the wireless receiver and IR unit Remove the two M5 x 10mm phillips screws and open the power enclosure as shown in detail 4 M5 x 10mm SCREWS _ DETAIL 3 8 SCREW DETAIL 4 15 of 23 ISSUED 08 24 12 SHEET 180 9036 3 10 31 12 Untie the wireless receiver power adapter cord and route as shown below Plug the end of the power adapter into the outlet marked DC on the wireless receiver as shown in detail 5 Coil up the excess cord and secure with a cable tie P Store the coiled cord between the power adapter and the power module wall as shown WIRELESS RECEIVER POWER ADAPTER DISPLAY NOT SHOWN FOR CLARITY DETAIL 5 O Locate the IR receiver inside of the wireless receiver enclosure shown in figure 10 1 Remove the tie from the cable and position the receiver on the display within line of sight of your remote as shown in figure 10 2 Remove the adhesive backing from the IR receiver eye and attach to the display Coil up the excess cord near the wireless receiver enclosure and secure with a cable tie P Store the c
Download Pdf Manuals
Related Search