USER MANUAL
Contents
1. ene 10 SPECIAL FEATURES OF THE LK5000 11 INTER STRING DELAY eee 11 MULTI LEVEL DEFINITION eene 12 SPECIAL CONFIGURATIONS eee 14 DATA TRANSFER MENU eee 16 SPEGCIFIGAT IONS 18 ADDENUM reno tee ees 19 FEATURES Optional left or right laser bar code reader Optional credit card reader e Contemporary design Fully programmable e POS Layout e Tactile mechanical key switches Keylock for multiple program layers Multiple shift layers True keyboard wedge function operates with or without computer keyboard e Up to 256 characters key include all function amp control keys No programming accessory kit TSR program or battery required Available with RS232C output CARTON CONTENTS LK5000 1 Keyboard Model LK5000 2 Computer interface cable RJ11 6 pin Male 3 101 keyboard interface cable PS 2 Male to AT Female 4 Utility software disk 5 Legend label sheet 6 Users manual HARDWARE CONNECTIONS The LK5000 can be connected to an IBM101 PC XT AT or clone computer PS 2 computer or computer terminal The following diagram shows how the keyboard connects to the computer and standard keyboard or other keyboard peripheral magnetic stripe reader scanner Reserved Peripheral Computer for optional2. MSR NOTE Before making any connections it is always advisable to turn off the computer Connecting the LK5000 to IBM101 XT AT or clone computer s keyboard port 1 Use the computer interface cable Plug the AT or PS 2 Male connector plug into the compter Connect the RJ11 connector into the To Computer connector on the LK5000 2 Connectthe keyboard interface cable to the standard keyboard The PS 2 Female connector plugs into the PS 2 connector on the rear panel of the LK5000 The RJ11 connector plugs into the To Peripheral connector on the back of the LK5000 FUNCTIONAL TEST For testing purposes your LK5000 keyboard was pre programmed with a template called LK5000 TPL The following simple steps will verify that the keyboard is in good working condition 1 Follow the Hardware Connections procedure described earlier in this manual to connect the LK5000 to your computer 2 Turn on your computer 3 Atthe DOS prompt press the upper left key of the keyboard 4 The keyboard is working correctly when the words LOGIC CONTROLS PROGRAMMABLE KEYBOARD MODEL LK5000 appears on the monitor To verify if the other keys are working simply press each key and verify that the information displayed on the monitor matches the template shown at the end of this section UTILITY DISK CONTENTS All LK5000 keyboards come with a utility software disk This disk contains several important files LK5000 EXE Use this
3. information changes from ASCII to SCAN NOTE The scan code mode will only be active for this cell You must select F8 for each cell you want to program with scan code information 3 Under the scan code mode each alphanumeric character is enclosed in parenthesis For special function or control keys press ESC three vertical bars will be present followed by the special function or control key you want to program For example to program the INS insert key press ESC and then the INS key on the 101 keyboard To program the ESC key simply press the ESC key twice Special function and control keys will not appear inside parenthesis The three vertical bars will disappear once the special function key is depressed 4 You may return to the start up graphic screen short menu by pressing Cirl Alt F4 again NOTES 1 Special function keys require ESC as the leading code In the scan code mode you can view the symbol of the special key or the hex code equivalent of the special key To view simply press F7 to toggle between symbol and hex modes Once a special function key shift ctrl alt etc is programmed it may be necessary to un select the function To do so press in sequence ESC f lower case F 0 zero ESC followed by the special function key shift ctrl alt etc Any given programmable location may be toggled between scan code mode and ASCII code mode Pressing the F8 key on the keyboard will change the cell s
4. key where the time delay character has been stored The monitor will display ABC immediately After the delay time you entered for this key has expired DEF will be displayed on the monitor and the cursor will be present at the prompt MULTI LEVEL DEFINITION This feature can increase the apparent number of programmable keys by allowing you to program different levels into any cell For every different level you program you must select another key to be a SHIFT LEVEL key Programming is accomplished in the normal manner After programming the base level a separator bar must be entered to separate the base level from the second level You can program more than two levels per cell For example if you needed to program small coffee medium coffee and large coffee into one cell follow the procedure outlined below 1 Select a blank cell and enter the most common coffee first medium coffee Mark the legend sheet for this cell COFFEE Enter the separator bar by depressing and holding the ALT key and pressing the letter S A solid line will appear on the programming line immediately following the last character typed Enter the second level small coffee followed by another separator Enter the third level of information large coffee The entire programming line should look like the following F5 MEDIUM COFFEE SMALL COFFEE LARGE COFFEE Select a blank location to F11 become the first level shift position Mark the legen
5. programming mode to scan code mode Pressing F9 on the keyboard will change the cell s programming mode to ASCII code mode Changing modes in a cell that has been previously programmed will erase all the information in that cell To enter hex scan codes directly press ESC followed by the 2 digit hex number For example to program the CTRL key press ESC followed by 1D The LK5000 program will add the leading zero 10 SPECIAL FEATURES OF THE LK5000 Besides being able to program all the keys of an IBM101 keyboard the LK5000 has also incorporated three state of the art features which will add flexibility and functionality to the keyboard INTER STRING DELAY This feature allows for a time delay s to be installed after a character s has been inserted into a cell To use this feature follow the steps below 1 Enter the character s which will precede the delay For example ABC Depress and hold the ALT key while pressing the letter D A time delay screen will open asking for the amount of delay you require up to 240 seconds Select the appropriate delay and press ENTER A square pixel will appear on the programming line immediately following the last character typed Type the next character s DEF You can use more than one delay per cell and each delay time can be different Save the template and then write the template to the keyboard Exit the LK5000 program by pressing F10 followed by the letter Y Press the location
6. utility with or without the keyboard being attached It is used to program the keyboard For a complete description of how this program works see the section Programming the LK5000 keyboard LK5000 TPL This template was pre programmed into the keyboard and matches the legend shown on the previous page If you have any questions on how to program a particular key you can refer back to this template to see how it was originally programmed INSTALLING THE LK5000 EXE UTILITY PROGRAM The first step in using the LK5000 EXE utility program is to copy the program to your hard drive 1 Insert the LK5000 utility software into drive A or B of the computer 2 MD LK5000 at the C gt prompt to make a directory named LK5000 3 Type CD LK5000 to make the LK5000 directory active 4 Type COPY A If the disk was inserted into drive A then all files will be copied into the hard drive s directory LK5000 If drive B is used then you must type COPY B STARTING THE LK5000 EXE PROGRAM This program can be used with or without the keyboard being attached to the computer Note that the PC must be booted up in DOS before starting the program It will not run properly under Windows DOS prompt To start the program type LK5000 at the LK5000 DOS prompt and press ENTER When the program is up it will automaticallly display the graphic graphics screen as below F2 File FS Recover F8 Scan code Mode 10 Quit F3 Configure
7. F3 By depressing the high lighted letter in each option the program will enable or disable that option The default settings are shown in the graphic below Send Break codes for scan codes Yes Enable beep while a key pressed Yes No beep if a key is undefined Yes Translate to code set 2 for AT Yes Emulating XT keyboard always No Use ALT num to generate ASCII No Enable Typematic for scan codes No Enable Typematic for ASCII codes No Emulating Link Terminal No InterCharacter Delay 2 mS Enable RS232 Output No Baud Rate 9600 Parity NONE Length of Data 8 bits Press a High light Letter to select Esc gt Quit from this menu 14 DESCRIPTION OF SPECIAL CONFIGURATION MENU F3 Send Break code for scan codes Enables or disables the transmission of break codes for each scan code programmed into the keyboard Enable beep while a key pressed Enables or disables the entire keyboard from beeping when any key is depressed No beep if a key is undefined If a key is not programmed it will not beep when depressed Translate to code set 2 for AT Enables or disables the output of the keyboard to be translated into AT scan code Emulating XT keyboard always Enables or disables the output of the keyboard to be translated into XT scan code Use ALT num to generate ASCII Enables or disables the ability to use the ALT ke
8. F6 Clear F9 fiscii code Mode F7 Symbol Hex Alt D Time Delay Alt A Shift Func Shift Available T Up Bytes 1856 Alt Separator Alt Caps Lock Left y Right own 124 115 125 PROGRAMMING THE LK5000 KEYBOARD The following procedure will show you how to program your LK5000 with standard keyboard alphanumeric characters The keyboard can be programmed with either ASCII or Scan code information The default mode is the ASCII code mode The following procedure assumes both a LK5000 keyboard and a 101 keyboard are attached NOTE To run this program you must exit windows completely Do not shell out from Windows 1 With the correct programming graphics present Select the cell you want to program by using the arrow keys on the 101 keyboard The Up and Down arrows will select the row while the Shift and either the Right or Left arrow key will select the column 2 Enter your programming text via the 101 keyboard Continue programming until all the keys are programmed It is not necessary to program all the keys for the LK5000 to function properly The maximum number of alphanumeric characters that can be programmed for any one key is 256 NOTE The maximum number of alphanumeric characters that can be programmed per standard keyboard is 1856 DATA TRANSFER MENU Dos shell File list tpl Load file from disk Read from keyboard Save file to disk Write to key
9. Model LK5000 Programmable POS Keyboard 58 Keys with Built in Scanner and MSR USER MANUAL LOGIC i CONTROLS NOTICE The manufacturer of the POS programmable keyboard makes no representations or warranties either expressed or implied by or with respect to anything in this manual and shall not be liable for any implied warranties of fitness for a particular purpose or for any indirect special or consequential damages Information in this document is subject to change without notice and does not represent a commitment on the part of the manufacturer FCC NOTICE This device complies with Part 15 of FCC Rules Operations is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation LOGIC CONTROLS INC 355 Denton Ave New Hyde Park NY 11040 TEL 516 248 0400 FAX 516 248 0443 Email lci logiccontrols com http www logiccontrols com TABLE OF CONTENTS FEATURES uitae anis NEM 1 CARTON CONTENTS esee rennen 2 HARDWARE CONNECTIONS eee 3 F NGTIONAL TEST ite caet ied meret 4 UTILITY DISK CONTENTS eme 6 INSTALLING THE LK5000 EXE UTILITY PROGRAM 7 STARTING THE LK5000 EXE PROGRAM 7 PROGRAMMING THE LK5000 8 ADVANCED PROGRAMMING
10. ONS MECHANICAL Weight Basic Unit 2 4165 with MSR 2 5lbs with Scanner 2 6lbs Dimension in inches SID w Scanner Width 15 7 15 9 75 7 5 Front Height 0 5 0 5 Height 1 8 2 2 wilegs ext 22 2 6 Keys Full travel mechanical Life cycle gt 10 million tactile cycles MSR 2 tracks standard Life Cycle 300 000 passes SCANNER Laser Class CDRH Class Il MTBF 100 000 hours ELECTRICAL Input voltage from computer 45VDC Current Basic Unit 25ma MSR 50ma Scanner Standby 15ua ScanMode 100 Surge 130ma ENVIRONMENTAL Operating Temp 0 C to 50 Storage Temp 20 C to 60 C Relative Humidity Operating 85 max non condensing Non operating 90 max non condensing Vibration 10 to 55 Hz 40 Shock 40G s INTERFACE Keyboard Wedge Standard RS232C Optional GENERAL INFORMATION Keyboard interface cable utility software and legend labels supplied PROGRAMMING THE KEYBOARD 1 Use the utility software supplied to program up to 256 alphanumeric characters per key Utility program will write to and read from computer disk memory 2 Keyboard supports computer control keys Shift CTRL ALT F1 through F12 and all arrow keys CONNECTOR PINOUTS J1 PS 2F to PS 2 Keyboard 1 Keyboard Data 2 No Connection 3 Ground 4 45VDC 5 Clock 6 Shield J2 RJ11F to Computer 1 Clock 123456 Data 3 No Connection 4 Ground 5 5VDC 6 No Connection J3 DB9M RS232C to Computer 1 DCD 2 Receiv
11. board Press ESC to Quit 3 Press F2 to call up the Data Transfer Menu There will be several choices to choose from 4 Wto write the programmed data into the LK5000 s non volatile memory A Writing Data screen will open showing the percentage of memory written It will take approximately 7 seconds to copy the data into the keyboard 10 Type S to save the programmed data into the LK5000 directory You can select up to an 8 character name It will be saved with a TPL extension Press ESC to terminate the Data Transfer Menu Press F10 followed by Y to exit the utility program To verify that your program has been successfully installed simply press any programmed key The information stored in that key will appear on the monitor The next time you want to install the legend you just created simple press F2 to call up the Data Transfer Menu and then press L to open the Load window Enter the name of the file in the legend window with its proper extension TPL and press ENTER The legend will now show on your monitor ADVANCED PROGRAMMING The LK5000 POS keyboard can be programmed with all special control and function keys such as the Shift Ctrl Alt F1 through F12 and the up down left right arrow keys The procedure to program these special keys is shown below 1 Start the LK5000 utility program 2 Select the cell to be programmed Press F8 to enter the scan code mode The code type
12. d sheet for this location SMALL Change the programming mode of this cell to scan code mode F8 Depress and hold the ALT key while pressing the letter A A triangle inside brackets lt gt will appear on the programming line This key when depressed and held will activate all keys that have a second level Select another blank location F12 This will become the second level shift position will activate the third level of information Mark the legend sheet for this position LARGE 8 Change the programming mode of this cell to the scan code mode F8 Depress and hold the ALT key while depressing the letter A twice Two triangles inside brackets will appear on the programming line 9 To use this feature in your application is extremely simple When medium coffee is desired just press the F5 key the first level of information stored in cell F5 will be sent to the computer When a small coffee is desired press and hold the F11 key while pressing the F5 key the second level of information stored in cell F5 will be sent to the computer When a large coffee is desired press and hold the F12 key while pressing the F5 key the third level of information stored in cell F5 will be sent to the computer NOTE There is no preset limit to the number of levels that can be programmed into a keyboard SPECIAL CONFIGURATIONS The keyboard can be set up with many different programming options To activate the configuration menu screen press
13. e Data from computer 3 Transmit Data to computer 4 DIR 5 Ground 1234 60500 pge 7 RTS 8 CTS 6789 9 No connection Pins 1 4 and 6 are tied together internally Pins 7 and 8 are tied together internally ADDENDUM SCANNER POSITION The LK5000 a matrix programmable keyboard with built in scanner was designed with the end user in mind The scanner can be factory installed on either side of the keyboard giving the end user the versatility required in todays applications PITCH ANGLE To accomodate different customer installations the scanner s pitch angle can be adjusted via a lever on the bottom side of the keyboard TO ACTIVATE THE SCANNER The upper key of rightmost column on the LK5000 has been hardwired to the scanner and serves as the scanner s trigger This key is dedicated to activating the scanner The scanner could also be set in an always state by changing the default settings on the scanner SYMBOLOGIES The default parameters of the scanner includes the reading of many different symbologies
14. eyboard Press ESC to Quit The LK5000 keyboard working in conjunction with the LK5000 EXE utility software can perform the following powerful functions Save programmed data as a template file TPL in both the keyboard and the hard drive of the computer To save programmed data to the keyboard use the W Write to keyboard option of the Data Transfer Menu To save programmed data to the hard drive use the S Save file to disk option of the Data Transfer Menu Load L a previously programmed template from the hard disk into the computers volatile RAM memory The same template can then be written W into the non volatile memory of the keyboard This process as an example allows a restaurant to change from a breakfast menu to a lunch menu within 7 seconds Enables the computer to read R a template stored in the LK5000 That template can then be saved S to the hard disk for future use Display a list of templates that have been stored onto the hard disk within the LK5000 directory From the Data Transfer Menu select F for File List The computer s monitor will display the list of TPL files stored in the LK5000 directory Interruption of the programming process to shell out to DOS D to perform other operations To return to the programming process type EXIT at the DOS prompt NOTE Never shell out of windows to work in this utility program Boot up computer in DOS LK5000 PROGRAMMABLE KEYBOARD SPECIFICATI
15. y along with the numeric keyboard to generate ASCII codes Enable typematic for scan codes Enables or disables keys programmed with scan code information to repeat the programmed characters as long as the key remains depressed Enable typematic for ASCII codes Enables or disables keys programmed with ASCII code information to repeat the programmed characters as long as the key remains depressed Emulating Link Terminal Enables or disables the keyboards ability to emulate a link terminal Intercharacter Delay The time delay between characters can be adjusted from 1 millisecond to 266 milliseconds This delay is set for all characters programmed into the keyboard Do not confuse this feature with the inter string delay feature DESCRIPTION OF SPECIAL CONFIGURATION MENU F3 CONTINUED Enable RS232 Output Enables or disables the output of the keyboard to the RS232 port DB9 connector If this option is set to YES then the protocol settings must be set to mirror the application software Baud Rate This option selects 2400 4800 9600 and 19 200 baud rates Parity This option selects ODD EVEN or NO parity Length of data This option selects either 7 or 8 data bits DATA TRANSFER MENU _ COMPUTER S J RAM Save MEMORY Write LK5000 KEYBOARD Load Read COMPUTER S HARD DISK Dos shell File list tpl Load file from disk Read from keyboard Save file to disk Write to k
Download Pdf Manuals
Related Search