RF-Card Reader - Emerson Network Power
Contents
1. below illustration Q CHD601P Configuration F1 1 DER Serial Port COM2 y Baudrate 9800 v Timeouts 500 nd Open Port E Net Address IE Clear Message Device Password Change Net Address Password 0000000000 NetNetAddress TE Change Password Change Net Address Change Baudrate New Baudrate 3 9600 bps X Read Version Change Baudrate Picture 4 CHD601P Series RF CARD READER 1 Select communicate interface and baud rate 2 Network ID pleases select 0 3 Click authority confirm button whether setup anything should pass the authority confirm and can success 4 Select option to finish setup 7 Packing List Colorized exterior package box and white inner package box One card reader Indicate model and ex factory date Some screws One 8 core lines One Users Manual Warranty card for guarantee to keep the reader in good repair2. CHD601P Series RF CARD READER RF Card Reader CHD601PM Series User s Manual Shenzhen Nevvabel Electronic Co Ltd CHD601P Series RF CARD READER Function introduction Performance parameters Installation instruction CONTENTS Instr ction of line CONNECTION semi memtatsmsactastzciiaiasittsitiaciiiaciacittstmttids 4 1 Tools and staff for instalatia paei aii 4 2 Installation step Software Setup Packing List Attention NOTES on connection sa ami mataro mata rss CHD601P Series RF CARD READER 1 Function introduction The communication agreement of CHD601P PM is compatible with HID5355K card reader The reader s is also used as accessorial device of the controller which is outside connected with a HID5355K card reader The communication interface is RS485 and Wiegand output it supports to open doors not only by reading cards but also by password through Wiegand 26 output The default format is Wiegang26 but could provide 34BIT 36BIT 44BIT format based on buyer s require The soft keypad of reader has comfortable hand feeling and there is a doorbell button a door open indicates light button show blue a warning indicates light show red Once you press the keypad the buzzer emits beeps and all keypads indicate blue backlight you can see keypads clear and operate it easy when in obscuration conditions See picture 1 the reader supports 3 m
3. der is with 8 lines connected with interfaces according to their colors CHD601P Series RF CARD READER ooooooon lt 335 2125 833 gt PD S BSR E Picture 2 1 white 2 green 3 black 4 red S orange 6 blue 7 purple 8 brown WD1 B WDO A GND 12V UNL OUT Swo Swi WD1 B Wiegand 1or RS485B WDO A Wiegand 0 or RS485A GND Ground 12V Install power supply DC 12V UNL Nill OUT Doorbell SW0 SW1 dismantlement proof output Notice The communication interface of the reader had been setup as VViegand output or RS485 format successful before leave factory users can t change 4 Installation instruction Guidelines gt You should have full consideration which is convenient for the future maintenance gt Installation in high temperature place for a long time is avoided gt The reader is avoided to get point blank sunshine and to be wet on the surface 4 1 Tools and staff for installation Installation tools Manual electric drills percussive drill cross screwdriver chisel wire cutter hammer etc Installation staff STP UTP network lines RJ45 crystal interface PVC screws etc E CHD601P Series RF CARD READER 4 2 Installation step 4 2 1 Choose the place to install This is a high precision apparatus and its stability and using time a certain extent depends on the place you choose to install it Thus the place
4. odes of opening doors by reading cards by password and by reading card amp password which is helpful to keep access control safe In adc eve it hi tor Light Light l Ae Door Open Indicator Light Cal Button a Mistake Indicator Light Picture 1 GD CHD601P Series RF CARD READER 2 Performance parameters Size L128mm X W84mm X H28mm Working Status three colored lights indication Keyboard key press operation under blue backlighting Environmental temperature working at 10 8 50 Gstore at 40 70 C Relative humidity lt 90 without condensation Environment requirement no dust no corrosive gas no flammable gas no oiled fog no vapor no dripping or salinity etc ESD anti jamming parameter air discharges 9KV touch discharge lt 6KV Power supply reted voltage 12VDC gt 200MA Power switch power supply static current lt 35 mA dynamic current lt 45 mA ID card work frequency 125KHZ IC card work frequency 13 56MHZ Effective distance ID card210cm IC card24 5cm speed of reading card lt 1second Transmission distance WieGang lt 60m RS485 51200 X OC port for alarm output 1group With alarm for dismantlement proof Communicate velocity default 9600BPS Can upgrade to 1200 38400BPS Remark able to change the communicate address by revise software when working at RS485 mode Net weight 150g 3 Instruction of line connection Please refer to Picture 2 this rea
5. you choose must be true of all the environment requirements according to performance parameters Meanwhile it cannot be installed in point blank and dusty places 4 2 2 Installation of the reader In the course of installation the reader s crust should be avoided being lacerated by some cuspidal things such as screwdriver to keep it a beautiful appearance 4 2 3 Metope disposal You d better have a good metope disposal before installation First you choose an appropriate height for on the wall 1 2 1 3m suggested Then you embed 84 cassettes into the wall according to its size Next you fix the bottom board of the reader and joint some network lines connected with the cassette You can refer to the following picture _ fill in glue fixing shell screw hole wucg Installation fixing screw l Picture 3 CHD601P Series RF CARD READER Then closed the shell and fix the screws finish the installation 5 Attention notes on connection 1 Refer to Picture 2 to definition correct connection 2 You are suggested to adopt 0 5mm lines material for DC12V circuitry and AWG16 AMG24 lines material for signal circuitry to reduce the degree of external interface so you d better not use shielded lines 3 Please note the connections of power supply don t mistake DC12V line is red and GND line is black 6 Software setup The availability of this software only for card readers that support RS485 and the setup as
Download Pdf Manuals
Related Search