UCAT-2 - Turbel
Contents
1. MAINTENANCE U CAT 2 Your UCAT 2 requires no maintenance Heavy Duty UCAT On Demand Powered Unwinder Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new e Constant Adjustable Torque CAT Labelmate products is outlined below technology Warranty Period Products Covered e Switched Directional and Dual Range Control Label Rewinders 5 years Label Unwinders e Precise Variable Torque Control Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Remove all parts from the shipping container and verify contents Power Supply Modules Counter modules Package Contents Encoders Any products not specified above e User Manual this document The warranty period for all products starts on the date purchased by the original end user customer e UCAT 2 Drive Unit Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has e Power Supply Module been modi2. fied is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for e LABELMATE Quick Chuck Quick Locking Core Chuck eQvelage Vericalon or Standard Shaft with three 3 metal Vanes installed In the event your product requires service please contact the distributor you bought the product from The or Model 10 INCHES Shaft with six 6 metal Vanes installed customer assumes responsibility for all cost and risk incurred in transport for service or Model ACH Adjustable Core Holder Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of e Two 300mm 12 Plastic Flange Plates One only for QC none for Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed ACH e Control Arm with setscrews and shaft screw LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com Retain the Shipping Container and Packaging for Storage and Transport e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e www labelmate com LABELMATE User_UCAT 2 02 07 SPECIFICATIONS POWER UNWINDING Max Label Roll Weight 7Kg 15 4Lb for Standard 1 Place the rol
3. l of labels to be unwound on the UCAT 2 15Kg 33Lb for QC 6Kg 13 2Lb for ACH 2 Run the labels under the Unwinder Control Arm and into the printer Max Label Roll Size 300mm 12 diameter 280mm 11 for ACH et Power Supply Inout 220 240VAG 50 60Hz Output 11VAC 2 5A 3 Place the UCAT 2 DIRECTION switch in the desired position according to which direction you want the UCAT 2 to feed the labels 4 Place the REWIND SLIT Switch in the REWIND position and set the TORQUE SET UP ADJUST about 1 3 rotation as an initial setting The UCAT 2 is bi directional It can unwind labels in either direction 5 Start your printer and observe how the labels are being fed into the printer First install the Control Arm referring to the enclosed TA User Manual 6 Adjust the TORQUE Control as needed to provide faster or slower unwind As the if you have the ACH Adjustable Core Holder option Skip to step 4 printer uses the labels the Control Arm will rise causing the Unwinder to turn on and STANDARD AND 10 Identify the inner Label Flange Plate Slide the Flange Plate feed more labels As the Unwinder feeds more labels the labels and the Control Arm will drop down turning off the Unwinder until more labels are needed and the Control onto the hollow end of the Unwind Shaft For maximum width the Flange face should aa i Arm is lifted again be flush with the end of the Shaft Tighten the screw in the Hub until it is snug No
4. t too tight CHUCK Mount the inner Flange onto the Quick Chuck with two screws provided EXTERNAL HALT CONTROL Slide the Shaft and Flange Assembly onto the UCAT 2 Motor Shaft allowing for clearance to the UCAT 2 Chassis and Control Arm Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight An External Halt Control jack on the UCAT 2 is for use with external devices capable of providing an open circuit halt command A 3 5mm control cable is necessary for use not included 4 ACH Slide the Hub of the ACH over the motor Shaft of the UCAT 2 Position the Hub so there is a gap between the ACH Hub and the Rewinder Drive Unit case Tighten With Pin 2 and Pin 3 of the External Halt Control circuit closed connected together using the Allen Screw onto the flat part of the Motor Shaft until it is tight a 3 5mm dual circuit plug the UCAT 2 will operate When the External Circuit is opened Set the UCAT 2 in place near the label entrance path to the printer AEE ASO CAUTION AVOID ACCIDENTS THE UCAT 2 WEIGHS OVER 10KG 22Lb SO 3 5mm EXTERNAL HALT CONTROL Plug Dual Circuit Plug CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT Contact GLOSED RUN Contact OPEN HALT 7 Verify that the DIRECTION Switch on the UCAT 2 Control Panel is in the OFF Ei EO CONC NON OT oe Pin 2 Normally Closed NC contact posnel Pin 3 Normally Closed NC contact return 8 Plug the Power Plug at the end of the wire on
5. the AC Wall Transformer into the CAT 12V 2 Power Input Jack Plug the AC Transformer into an appropriate AC power outlet EXT HALT CONT lt 10K The unit is now ready for use 4 e 3 5 mm Jack e Dual Circuit 10K S AV warnine J This Product is for indoor use only Not for use in wet locations
Download Pdf Manuals
Related Search