user manual Washing Machine
Contents
1. Start Pause pushbutton flashes red Softener runs directly in to the drum when filling the dispenser box 1 Depending on model all packaging have not been removed from the appliance see installa tion section the appliance isn t level and is unbalanced the appliance is too close to the wall or furniture washing is unevenly distributed in the drum the load is too small the water inlet filters are dirty the power or water supply has been cut off the motor overheating detector has been activated the water inlet temperature is lower than usual the foam detection security system has been activated too much de tergent and the washing machine has begun draining the foam the out of balance detector has been activated an extra phase has been added to distribute washing more evenly in the drum the water or electricity supply is defective a Rinse hold has been selected the drum shutters are open the immediate opening light is not lit the temperature inside the drum is too high the lid unlocks 1 2 minutes after the end of the cycle the lid is not closed properly the drainage filter is obstructed the drain hose is blocked or bent the drain hose is fixed to high see Installation section the drainage pump is blocked the standpipes blocked the water tap is closed the water supply has been cut off a red tab appears on the water inlet hose the drainage filter is2. Wool cold 40 Machine washable 1 0 kg Night silence plus Delay start wool carrying the labels pure new wool ma chine washable does not shrink 13 Silk cold 30 Fabric machine wash 1 0 kg Night silence plus Delay start able at 30 C Lingerie cold 40 For very delicate 1 0 kg Night silence plus Delay start items like lingerie E Rinse Hand washed items can be 5 5 kg Night silence plus Rinse plus Delay rinsed in this programme start by Drain Runs an empty cycle after a Rinse 5 5 kg hold Night silence plus Spin A spin cycle from 500 to 5 5 kg Delay start 1300 1000 rom after a Rinse hold Night si lence plus S Eco 40 90 White or colour e g 55 kg Night silence plus Prewash Rinse normally soiled work clothes bed linen table plus Delay start linen body linen towels A Easy iron cold 60 For washing cot 1 0 kg Prewash Rinse plus Delay start tons and synthetics Reduces creasing and makes ironing easier N Jeans cold 60 For washing denim 3 0 kg Night silence plus Prewash Delay clothes The Rinse plus option is activated start fF intensive sport cold 40 For dirty 25 kg Night silence plus Rinse plus Delay outside sport clothes The Prewash option is Start activated TF Sport 30 For sport clothes 2 5 kg Delay start 1 Depending on model 2 Reference programme for test confirming to CEI 456 standard 46 L 0 93 kWh 190
3. few items only 1 To use on a half load 2 The symbol flashes and disappears this wash cycle is a refresh cycle only The availability of these different levels var ies depending on the selected programme type Start of the programme Press the Start Pause P pushbutton to start the cycle the corresponding light will come on green It is normal for the pro gramme selector to remain stationary dur ing the cycle The symbol for the current cycle and the remaining time appear on the display If a delayed start has been selec ted the countdown appears on the display Warming up During the cycle the i symbol comes on when the appliance is reaching the right temperature Interrupting a programme Adding washing PROGRAMMES TABLE When the Add washing light is on you can add washing by proceeding as follows Press the Start Pause pushbutton the corresponding light will flash green while the appliance is paused The lid can only be opened around 2 minutes after the washing machine has come to a stop Press the Start Pause P pushbutton again to con tinue the programme Modifying the programme in progress Before making any changes to the current programme you need to pause the wash ing machine by pressing the Start Pause P pushbutton If the modification is not possible Err flashes in the display and the Start Pause P pushbutton flashes red for a few second
4. obstructed the anti flooding security system has been activated please proceed as follows close the water inlet tap empty the appliance for 2 minutes before unplugging call the after sales service you have gone past the MAX indicator 2 On some models the auditable signals can sound 3 After solving any problems press Start Pause pushbutton to restart the interrupted programme DETERGENTS AND ADDITIVES Only use detergents and additives designed for use in a washing machine We do not recommend mixing different types of deter gents This may spoil the washing There 10 electrolux are no restrictions on the use of powder de tergents Liquid detergents must not be used when a prewash or the reference pro gramme see Programmes table has been selected For cycles without prewash they TECHNICAL SPECIFICATIONS DIMENSIONS Height Width Depth LINE VOLTAGE FREQUENCY POWER CONSUMPTION WATER PRESSURE Minimum Maximum Connection to water supply INSTALLATION Remove all protective packaging for transit before using for the first time Keep in case needed for future transit Transporting a non secured appliance may damage inter nal components and cause leakages and malfunctions The appliance can also be damaged through physical contact Unpacking must be added via means of a dosing ball Detergent tablets or doses must be placed in the detergent compartment of your appl
5. the same process e Run an initial wash cycle at 90 C without any washing but with deter gent to clean the water tank drum and the lid of your washing ma chine Warning Before closing the lid of your appliance ensure that the drum is properly closed e When the two shutters are closed e locking button A released Proportioning of detergents Pour the amount of washing powder into the washing LIL and prewash 1 compart ments if you have selected the prewash option Pour fabric softener into the com partment amp if necessary Selection of desired programme Turn the programme selector to the re quired programme The Start Pause P pushbutton flashes green If you turn the programme selector to an other programme while a cycle is in pro gress the appliance will ignore the new se lected programme Err flashes and the Start Pause P pushbutton flashes red for a few seconds Selecting the temperature Press the Temperature pushbutton re peatedly to increase or decrease the tem perature see Programmes table The symbol means a cold wash Selecting the spin speed Press the Spin pushbutton to change the spin speed The maximum spin speeds are for Cottons Eco 1300 rpm EWT135410W 1000 rom EWT105410W for Wool Lingerie Jeans 900 rpm EWT135410W 1000 rpm EWT105410W for Synthetics Easy iron Intensive sport 900 rpm for Delicate
6. the tap and disconnect the inlet hose e Place the end of this hose and the drain hose in a basin on the floor e Select the Drain programme let it run until the end of the cycle e Disconnect the appliance from the power supply by turning the programme selec tor to Stop O e Unplug the appliance e Replace the inlet hose and drain hose This way the water remaining in the hoses will be drained away avoiding any ice for mation which would damage your appli ance Before turning your appliance on again en sure that it is installed in an area where the temperature will not fall below freezing 4 electrolux Use e Your appliance is intended for normal do mestic use Do not use the appliance for commercial or industrial purposes or for any other purpose e Refer to the instructions on the label of each item before washing e Do not put items into the washing ma chine which have had stains removed with petrol alcohol trichlorethylen etc If such stain removers have been used wait until the product has evaporated be fore putting these items into the drum PERSONALISATION Child safety This option provides two types of locking e if the option is activated after the cycle has started no changes to the options or programme is possible The cycle runs and you must deactivate the option to run a new cycle e if the option is activated before the cycle has started the appliance cannot be started
7. For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Disposing of the appliance All materials carrying the C5 symbol are recyclable Dispose of them at a waste electrolux 11 Electrical connection This washing machine must only be con nected in single phased 230 V Check the fuse size 13 A for 230 V The appliance must not be connected with an extension lead or multi plug adaptor Ensure that the plug is earthed and that it is in accordance with current regulations Positioning Position the appliance on a flat and hard surface in a ventilated location Ensure the appliance does not come into contact with the wall or other furniture Accurate levelling avoids vibrations noise and prevents the appliance from moving when running collection site enquire at your local council for collection and recycling When disposing of your appliance re move all parts which could be danger ous to others cut off the power supply cable at the base of the appliance Protecting the environment ws To save water and energy and there fore help protect the environment we recommend the following e Whenever possible use the appli ance at full capacity and avoid partial loads e Only use the prewash and soak pro grammes for heavily soiled items e Use an appropriate
8. Thinking oF pri user manual Electrolux Washing Machine EWT 135410 W EWT 105410 W 2 electrolux Control panel N The control panel Lid button Filter access cover Adjustable levelling feet e e A e e e e V e e e e e e e e L JL JL JL JL Ed 6 1 Programme selector 2 Pushbuttons and their functions 3 Display 4 Add washing light 5 Start Pause pushbutton 6 Time manager pushbuttons The symbols 1 Time manager 2 Temperature 3 Child safety 4 Cycle running UJ Prewash Wash SE 0 08 p Wik gi Rinse ky Drain Spin Length of cycle or Timer delay count down Dispenser box iS SAFETY INFORMATION Please read these points carefully before in stalling and using your appliance Keep this user manual with your appliance LJ Prewash UJ Wash General safety e Do not modify or attempt to modify this appliance This would put yourself in dan ger e Ensure that all coins safety pins brooch es screws etc have been removed be fore starting a washing programme If left in washing they can seriously damage the appliance e Use the recommended quantity of deter gent e Put small items together Socks belts etc in a small linen bag or pillow case e Unplug and close inlet hose tap after us ing appliance e Always disconnect the power supply from the appliance before cleaning or maintenanc
9. To activate child safety turn appliance on and press Rinse plus j and Delay start simultaneously until the confirmation symbol G shows on in the display The ap HOW TO RUN A WASH CYCLE Using for the first time e Ensure the electrical and water con nections comply with the installation instructions e Remove the polystyrene insert and all other items inside the drum DAILY USE Loading washing e Open the lid of the appliance e Open the drum by depressing the locking but ton A The two shutters unlock automatically e Load the wash ing close the e Empty pockets and unfold items e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge un less they have been given supervision or instruction concerning use of the appli ance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance pliance memorises the selection of this op tion To deactivate child safety repeat the process Audible signal When the audible signal is activated it sounds when a button is pressed at the end of the programme to indicate a fault To deactivate turn appliance on and press Prewash LLJ and Rinse plus J simulta neously until the beep sounds The signal is only active if alarm sounds To reactivate it repeat
10. amount of deter gent for the hardness of the water the size of the load and how soiled the washing is www electrolux com shop DAQE 108526701 B 492010 CE
11. e e Do not machine wash clothes with rib bing unfinished or torn material Installation e Unpack or ask for the appliance to be unpacked immediately upon delivery Check the outside of the appliance is not damaged in any way Report all transit damage to your retailer e Remove all transit bolts and packaging before installing the appliance e Connection to the water supply must be carried out by a qualified plumber e f your domestic electrical circuit needs adapting to allow the appliance to be plugged in use a qualified electrician e Ensure that after installation the power cable is not trapped under the appliance electrolux 3 amp Softener do not fill above the MAX symbol M e If the appliance is installed on carpeted floor ensure that the carpet does not ob struct any ventilation ducts located at the base of the appliance e The appliance must be equipped with an earthed power plug which conforms to regulations e Before connecting your appliance to the power supply carefully read the instruc tions in the chapter entitled Electrical connection e Replacing the power cable should only be carried out by an authorised service engineer e The manufacturer cannot be held re sponsible for any damage resulting from incorrect installation Precautions to be taken against frost If your appliance is exposed to tempera tures below 0 C the following precautions must be taken e Close
12. i ance s dispenser box 850 mm 400 mm 600 mm 230 V 50 Hz 2300 W 0 05 MPa 0 5 bar 0 8 MPa 8 bar Type 20 27 Untying To install your washing machine at the same level as surrounding furniture pro ceed as shown on picture 4 Water supply Install the supplied water inlet hose at the rear of your washing machine by proceed ing as follows Do not reuse an old hose The water inlet hose can not be extended If it is too short please contact the after sales service Open the water inlet tap Check there are no leaks Drainage Fit the U piece on the drainage hose Place everything in a drainage point or in a sink at a height of between 70 and 100 cm Ensure it is posi tioned securely Air must be able to en ter the end of the hose to avoid any risk of siphoning The drain hose must never be stretched If it is too short contact an engineer ENVIRONMENT CONCERNS The symbol K on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product
13. min CARE AND CLEANING Unplug the appliance before cleaning Descaling the appliance To descale the appliance use an appropri ate non corrosive product designed for washing machines Read product label for recommended amounts and how often descaling should be carried out The exterior Use warm soapy water to clean the exterior of the appliance Never use alcohol sol vents or similar products Dispenser box To clean proceed as follows Drainage filter Clean the filter located at the base of the appliance regularly 8 electrolux Water inlet filters To clean proceed as follows OPERATING PROBLEMS Numerous checks were carried out on your appliance before it left the factory Howev refer to the sections below before contact ing the after sales service er should you notice a malfunction please The washing machine doesn t start or doesn t fill The appliance fills but empties straight away The washing machine doesn t rinse or doesn t empty You have found water around the washing ma chine Wash is unsatisfactory the appliance isn t plugged in correctly the electrical installation isn t working the lid of your appliance and the drum shutters aren t closed firmly the programme start command hasn t been properly selected there is a power failure the water supply has been cut off the water inle
14. s Silk Sport 700 rpm At the end of the programme if you have selected Rinse hold J or Night silence plus you then need to select a Spin or Drain ty programme to finish the cy cle and empty the water Night silence plus the cycle contains no spin and ends with a rinse hold Selecting options You must select the different options after selecting the programme and before press ing the Start Pause pushbutton see Programme table Press the desired but ton s the corresponding lights come on If pressed again the lights go out If one of the options is not compatible with the se lected programme Err flashes on the dis play and the Start Pause P pushbutton flashes red electrolux 5 Prewash option UJ The appliance runs a prewash at 30 C max Rinse plus option The washing machine will add one or more rinses during the cycle This option is rec ommended for people with sensitive skin and in soft water areas Temporary Press the Rinse plus j pushbutton The option is only active for the selected programme Permanent Hold down the Prewash UJ and Delay Start pushbuttons for a few seconds The option is permanently activa ted even if the appliance is switched off To deactivate it repeat the process Delay start CY This option allows you to delay the start of a wash programme by 30 60 90 2 hours
15. s If you still decide to change the programme you must cancel the cur rent programme see below Cancelling the programme If you want to cancel the programme turn the programme selector to the Stop posi tion End of the programme The washing machine stops automatically the Start Pause pushbutton goes out and 0 flashes on the display The lid can only be opened around 2 minutes after the washing machine has come to a stop Turn the programme selector to the Stop O position Remove washing Unplug and close water inlet tap Stand by once the programme has finish ed after a few minutes the energy saving system will be enabled The brightness of the display is reduced By pressing any but ton the appliance will come out of the ener gy saving status Programme Type of washing Possible options amp 2 Cottons cold 90 White or colour 5 5 kg Night silence plus Prewash Rinse e g normally soiled work clothes bed linen plus Time manager Delay start table linen body linen towels A Synthetics cold 60 Synthetic fab 2 5 Kg Night silence plus Prewash Rinse rics body linen fab coloured farics non iron shirts blouses plus Time manager Delay start electrolux 7 Programme Type of washing Possible options Delicates cold 40 For all delicate 2 5 kg Night silence plus Prewash Rinse materials for example curtains plus Time manager Delay start
16. t tap is closed the water inlet filters are dirty a red tab appears on the water inlet hose the drainage U piece is fixed too low see installation section e the drain hose is blocked or bent the drainage filter is obstructed e the out of balance detector has been activated washing is unevenly distributed in the drum the Drain programme or Night Silence Plus or Rinse hold option have been selected the height of the drainage U piece is unsuitable too much detergent has caused foam to overflow the detergent is unsuitable for machine washing the drainage U piece isn t attached correctly the drainage filter hasn t been put back in place the water inlet hose is leaking the detergent is unsuitable for machine washing there is too much washing in the drum the wash cycle is unsuitable there isn t enough detergent electrolux 9 Problems Causes The appliance vibrates is noisy The wash cycle is much too long The washing machine stops during a wash cy cle The lid doesn t open at the end of the cycle The E40 error code ap pears in the display and the Start Pause pushbutton flashes red 3 The E20 error code ap pears in the display2 and the Start Pause push button flashes red The E10 error code ap pears in the display and the Start Pause pushbutton flashes red The EFO error code ap pears in the display and the
17. to 20 hours The selected time appears on the display for a few seconds You can change or cancel the delayed start time at any time before you press the Start Pause P pushbutton by pressing the Delay start Y pushbutton again 0 indicates immediate start If you have already pressed the Start Pause P pushbutton and you want to change or cancel the delayed start pro ceed as follows e To cancel the delayed start and start the cycle immediately press Start Pause Dll and then Delay start Press Start Pause to start the cycle e To change the timer delay period you must go through the Stop position and reprogramme your cycle The lid will be locked during the delayed start time If you need to open it you must first pause the appliance by pressing the Start Pause P pushbutton After closing the lid again press the Start Pause pushbutton Time Manager The cycle can be made longer or shorter by using the Time Manager pushbuttons The level of soiling of the laundry is also in dicated 6 electrolux Intensive For heavy soiled E items Normal S For normal soiled items Daily eS For daily soiled items Light eS For slightly soiled items Quick E For very slightly soiled items Super quick 7 For items used or worn for a short time Refresh 2 For refreshing items only Super re TF2 For refreshing a very fresh
Download Pdf Manuals
Related Search