Bluetooth GPS Receiver
Contents
1. Acquisition Rate Hot start 1 sec average with ephemeris and almanac valid Warm start 38 sec average with almanac but not ephemeris Cold start 42 sec average neither almanac nor ephemeris Reacquisition 0 1 sec average interruption recovery time Protocol GPS Output Data NMEA 0183 protocol and supports command GGA 1sec GSA 1 sec GSV 5 sec RMC 1sec VTG and GLL are optional GPS transfer rate 38400 N 8 1 Dynamic Condition Acceleration Limit Less than 4g Altitude Limit 18 000 meters 60 000 feet max Velocity Limit 515 meters sec 1 000 knots max Jerk Limit 20 m sec 3 Voltage Built in rechargeable battery 1650 mAh and 5V DC input charging circuit Operation Time 15 hr After fully recharged in continuous mode gt 20 hr in trickle power mode Physical Characteristics Dimension 72 5mm x 40 4mm x 26mm Weight 750 Temperature Operating 20 60 C Storage 30 80 C Humidity Up to 95 non condensing 3 2 Bluetooth Specification e Bluetooth V1 2 Compliant e Supply Voltage 2 8V 3 3V e Frequency Range 2 402 2 480 GHz e Receiver Sensitivity 80 dBm e Transmit Power Class 2 e Transmitting Range 10 Depends on environment Power Consumption 45 mA Typical 4 Usage 4 1 For PDA with built in Bluetooth 1 Turn on the power switch in BT 339 2 Please refer to the user manual of PDA to enable the Bluetooth of PDA connecting to the BT 339 Some PDAs may need the Blu2. space performing the positioning task Check if power level is sufficient Ifthe red LED lights up it means the power is insufficient please recharge it until the red indicator is off recharge is complete FCC Notices This device complies with part 15 ofthe FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC RF Exposure requirements This device and its antenna s must not be co located or operation in conjunction with any other antenna or transmitter NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT 13
3. the power button 1 second until the power LED is on Power off Press the power button 1 second until the power LED is off 2 3 Power Jack The power jack lets you to connect either aDC car power charger included or AC power charger included to recharge the internal battery Please note that the adapter rating 5V 1 2 A positive pole center 2 4 LED Function Bluetooth Status LED Blue Blinking Slowly Not connected to any Bluetooth device Blinking Quickly Connected to other Bluetooth device GPS Status LED Green Blinking GPS position is fixed Steady light GPS position is not fixed Battery Status LED Red Yellow Red Battery power is critically low Charge immediately Yellow Battery is charging now LED off Battery is partially full or fully charged 2 5 Power saving Function When you start the power of the Bluetooth GPS Receiver BT 339 if the Bluetooth is not connected to any devices within 10 minutes BT 339 will turn off the power automatically and all the LED will go off simultaneously 3 Specification 3 1 System Specification Electrical Characteristics Receiver Frequency L1 1575 42 MHz C A Code 1 023 MHz chip rate Channels 20 all in view tracking Tracking Sensitivity 159 dBm Accuracy Position Horizontal 10m 2D RMS SA off WAAS enabled 5m 2D RMS SA off Time 1 micro second synchronized to GPS time Velocity 0 1m sec 95 SA off Datum WGS 84
4. User Manual Bluetooth GPS Receiver BT 339 ver 1 06 1 BT 339 at a glance 1 1 Appearance and Function Power LED GPS status LED Bluetooth status LED Power buttom 1 2 How to change battery Figure 1 Open the cover of battery Figure 2 Take out the battery with pull tag Figure 3 Put new battery into BT 339 Figure 4 Fit battery into BT 339 Figure 5 Slide the cover of battery to close Figure 6 Slide the cover of battery to close 1 3 Accessories Car charge adaptor Travel charge adaptor 2 Introduction The BT 339 is aGPS receiver with Bluetooth interface and built in active antenna for high sensitivity to tracking signal Based on the SiRF star III Low power chip set and supports all functions Single Sat updates in reduced visibility Superior urban canyon performance FoliageLock for weak signal tracking etc The BT 339 is well suited to system integrations including PDA Smart phone Tablet PC and Notebook PC with Bluetooth devices It satisfies a wide variety of applications that are purposes in automotive and outdoor recreation navigation systems 2 1 Package Before you start up make sure that your package includes following items If any item is missing or damaged please contact your dealer immediately Bluetooth GPS Receiver A CD with the User Manual and the Testing Program AC Power Charger DC Car Power Charger 2 2 Power Switch Power on Press
5. d ActiveSync 2 Run the GPS Information program from Start gt Program files of PDA Here is the description of GPS Information testing program User must select COM port Baud Rate 38400 and click the Star GPS button to start receiving GPS data Note The Bluetooth device in most of the applications have an auto detect feature that you do not need to select the Baud Rate COM Port Select Baud Rate Select Scan Com port Start Close receving data Cold Start to GPS Setup GPS Info About s 11 Lat 24 59 8868 Lon 121 29 2218 HHI II 10 24 04 02 18 T 29 13 01 05 30 08 setup GPS INFO About 12 Trouble shooting Bluetooth is unable to connect A Check ifthe GPS Bluetooth indicator is flashing normally That is flash one per each three second means the product is under standby mode flash once per second means Bluetooth has been online already B Check if energy level is sufficient Ifred LED is lid up then the battery level is insufficient please recharge it until the red indicator is off recharge is complete GPS cannot be positioned A Check if GPS indicator operates normally or not If the indicator is constantly lid up it means that GPS is in operation if the indicator is flashing it means GPS is positioned already B If GPS cannot be positioned for long apply GPS info software to make a Cold Start first and then move to an open
6. etooth passkey the passkey is 0000 3 Check the number of COM port used by Bluetooth 4 Run the suitable mapping navigation software and select the correct COM port amp baud rate 38400 4 2 For PDA with Bluetooth Compact Flash card 1 Turn on the power switch in BT 339 2 Please refer to the user manual of Bluetooth Compact Flash card to enable it connects to the BT 339 Some Bluetooth devices may need the Bluetooth passkey the passkey is 0000 3 Check the number of COM port used by Bluetooth Example COM 6 4 Running the suitable mapping navigation software and select the correct COM port amp baud rate 38400 4 3 For Notebook with Bluetooth device 1 Turn on the power switch in BT 339 2 Please refer to the user manual of Bluetooth device to enable it connects to the BT 339 Some Bluetooth devices may need the Bluetooth passkey the passkey is 0000 3 Check the number of COM port used by Bluetooth Example COM 6 4 Running the suitable mapping navigation software and select the correct COM port amp baud rate 38400 Note The Bluetooth device in most of the applications have an auto detect feature that you do not need to select the Baud Rate 10 5 How to test your Bluetooth GPS Receiver The testing program only supports the Microsoft Windows CE amp Pocket PC based PDA platform 1 Run the GPSinfo exe to execute the installation procedure of testing program via PC an
Download Pdf Manuals
Related Search