Installation Instructions
Contents
1. ION TURN OFF POWER AND UNPLUG ALLOW TO COOL AT LEAST 10 MINUTES BEFORE REPLACING BULB NOTE Do not use a bulb greater than 9 watts Please use a CFL Bulb Fig 1 9 watts E 26 instead of other shape or sphere shape because it will cause higher temperature to mirrors 1 Turn the switch to the OFF position and unplug the lighted mirror 2 Unscrew and remove screws using screw driver from both sides of the mirror housing near the rotating hinges Fig 2 3 Lift off the top half of the housing from the bottom half that is affixed to the stand 4 Unscrew the old bulb and replace with the new bulb Fig 3 5 Replace the top housing half and tighten two screws into screw holes TROUBLE SHOOTING NO LIGHT Bulb is not break and switch is in the ON position 1 Check the plug and outlet 2 Carefully unscrew the bulb and screw it back after follow the procedure of TO REPLACE BULB 3 If there is still no light unplug the lighted mirror and call the manufacturer CLEANING AND MAINTENANCE Always unplug lighted mirror first Clean the outside of appliance with a damp cloth Never immerse it in water or any other liquid Clean mirror surfaces with a glass cleaner Do not light until you are certain mirror is completely dry to protect against electrical hazards turn over Front 914X5HW Eng User Manual INSTALLATION INSTRUCTIONS 1 Aptations Inc recommends using a qualified elec2. LIGHTED WALL MOUNTED MIRROR INSTRUCTION SHEET 91405HW 91415HW 91425HW 91435HW 91445HW 91455HW 91465HW 91475HW 91485HW 91495HW 914135HW FEATURES The lighted mirror is suitable in a dim lighted room The built in 9 watts Spiral Compact Fluorescent bulb is a suitable light source for makeup and it does not need extra light source which can save more energy and avoid interrupting other people in the same room OPERATING INSTRUCTIONS 1 Turn switch to the OFF position Plug cord into any standard 120 volt wall outlet Turn switch to the ON position 2 Lighted mirror will rotate so that you can use either the normal flat mirror or 5X magnifying mirror located on the opposite side 3 After use always turn switch to the OFF position 4 Unplug it from outlet when not in use IMPORTANT SAFETY INSTRUCTIONS THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE WHEN USING ELECTRICAL APPLIANCES BASIC SAFETY PRECAU TIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING WARNING To reduce the risk of burns electrocution fire or injury to persons 1 Read all instructions before using the appliance and keep them for later reference 2 To protect against electrical hazards do not use while bathing or in the shower and do not touch plug or switch with wet hands 3 To reduce the risk of burns 3 1 Avoid swivel the makeup mirror into horizontal position when turn switch to ON 3 2 Do not touch the housing e
3. specially the top half and mirrors when turn on the switch or off within 10 minutes 4 Repairs and service should always be carried out by an authorized service center Do not use the appliance if it is damaged or if the cable is damaged Instead send it to a service department 5 Be sure mirror is not in a position where it can reflect sunlight reflected sunlight can cause fire 6 After use always pull the plug from the socket 7 Handle cord carefully for longer life do not jerk or strain at plug connections or wrap cord around mirror for storage This could cause damage to the cord and short circuit To store mirror coil cord loosely 8 Use only the original accessories supplied 9 Allow the light bulb in the mirror time to cool down before storing it away 10 Do not lay a switched appliance on soft furnishings such as a bed cushion etc This will prevent over heating 11 Instruct young children about the dangers and safety rules concerning electrical equipment 12 Never let young children use electrical equipment without supervision 13 Turn switch to OFF position and unplug cord before replacing light bulbs 14 Do not place hang or store appliance where it can fall or be pulled into a tub or sink 15 If an appliance falls into water unplug it immediately Do not reach into the water 16 Never use while sleeping 17 Do not place in or drop into water or other liquid Please TO REPLACE BULB CAUT
4. trician for all electrical wiring procedures and installations 2 Astandard 120 Volts AC electrical box must be installed at the desired location of the wall before continuing 3 Remove the mounting screws on both sides of the mirrors base 4 Remove the mounting plate from the base and unfastened the green ground wire attached to the mounting plate Mounting Plate Ground wire Mirror Base 5 Secure the mounting plate to the electrical box on the wall with four 4 wall anchors and mounting screws Dim 227mm W x 273mm H Letter height at less 1 6mm 6 Feed the electrical wires from the electrical box through the mounting plate and reserve convenient length 7 Connect the electrical wires coming from the electrical box to the terminal connections in the base of mirror Tighten the set screws and re fasten the ground wire from the mirror to its fastening location on the mounting plate that is attached to the electrical box The mirror must be grounded when installed Wire references are L Live wire Line Phase Black wire N Neutral White wire gt Ground Green Yellow wire 8 Finish installing mirror by mounting base of mirror over the base plate that is attached to the electrical box 9 Fasten the mounting screws on both sides of the base 10 Put mirror at desired position and turn black rocker switch on for use Back 7July 11
Download Pdf Manuals
Related Search