User Manual DLK640 Plus
Contents
1. See VED 2 LED3 codeis Changed by Valid in mode level user 1 Off Off inactive NO 2 off On active YES 24 hour 3 On Off active NO day 4 On On active YES day 30 Integrated Technical Vision Ltd http www itvsystems com ua Limited Warranty Limited Warranty Integrated Technical Vision Ltd warrants that for a period of eighteen months from the date of purchase the product shall be free of defect in materials and workman ship under normal use and that in fulfillment of any breach of such warranty Inte grated Technical Vision Itd shall at its option repair or replace the defective equip ment upon return of the equipment to its repair depot This warranty applies only to defects in parts and workmanship and not damages incurred in shipping or hand ing or damages due to causes beyond the control of Integrated Technical Vision Ltd such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of the equipment The foregoing warranty shall apply only to the original buyer and is and shall be lieu of any and all other warranties whether expressed or implied and of all other obligations or liabilities on the part of Integrated Technical Vision Ltd This warran ty contains the entire warranty Integrated Technical Vision Ltd neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assu2. new code e 01 relay 2 control 02 relay 1 control 03 relay control inquiry Hos code editing 04 code removal code number or code 05 reset to factory defaults H new code engineer code 12 lockout time 11 alarm signal time value ol LE y 10 value 04 relay actuation time 05 entry time 06 future used 07 relay time 08 entry time display code options editing yeyomoy Gurwwesbo d 199u Buy XIGNAddV XIGNAddV Bn W09 SWUa SASAP MMA d y i gt 1413 relay 1 default time A um AE ae i p indication al value gt 14 relay 2 default time 5 time XXXXXXXXXX 1 gt ia value 4 gt code entry 15 default door time 4 W p APPENDIX 2 Access levels access relay entry Ne e time 00 lengineer 01 ee SEE ES RES 02 requestto exit J f T T 9 a parameter value factory defaults activation Lockouttime a0 seconds _ http www itvsystems com ua Integrated Technical Vision 29
3. CM2 NC2 Relay2 normally open common and normally closed termi nals NO1 CM1 NC1 Relay1 normally open common and normally closed termi nals Mounting DLK 640Plus stand alone access control unit is to be mounted indoors at 85 relative humidity DLK640Plus mounting description Release the screw in the bottom of the cover pos a on Figure 3 Slightly pull the bottom side of the cover pos b on Figure 3 and take it down Disconnect the keypad PCB from the base plate connector X3 a Mounting holes Wiring holes Mark the position of the fixing holes on the wall using back plate as a pat tern pos c on Figure 3 Drill fixing holes of the appropriate depth with 6 mm drill Pull the wiring through the holes on the back plate and secure the wiring with supplied screws Connect the wires Connect the keypad PCB to the baseplate with a screw Fix firmly the front cover http www itvsystems com ua Integrated Technical Vision 9 Operation Request to Exit RTE Button Request to Exit Button opens a door to exit the premises You can also use RTE button for remote door opening by the guard or secretary Direct opening by engaging of the electric lock or door strike will cause the alarm mode switch Depressing of the RTE button is identical to introducing user code 2 All settings of the RTE button are to be program
4. c rec thewgerae tia 20 User code FEVIOW cido dd dada 20 button programming mode eeeecceeceeeceeeeeeeceeeeeeeeeeeeeeeeeeeeeneeaaeeas 21 APPENDIX Uat isa 22 Access Control System 00coooonnnncccccnnnocooncccnnnnnnnn nc ncnnnn ano n nn nn narran nn cnn anna 22 High Degree Security Access Control System occncncnnncccocccncncccananinonannnnnn 24 APRENDIZ A O aaa 28 Limited Warranty ve crtertiericos tenida cc 31 4 Integrated Technical Vision Ltd http www itvsystems com ua Preface Preface DLK640Plus standalone access control panel is intended for access control sys tem creation and or use in intruder alarm systems The panel provides one or two execution units control by means of code entry DLK640Plus is characterized by presence of nonvolatile memory two relays alarm output one engineer code one chief code and 29 users codes Valid code intro duction allows you relay control and day night modes change The panel supports such advanced features as request to exit keypad lockout duress code two ac cess levels It has three light emitting diodes LED http www itvsystems com ua Integrated Technical Vision 5 Features Features Specifications Electrical Mechanical Environmental Fully programmable from the built in keypad Three LEDs Built in buzzer Utilizes keypad codes from 4 to 10 digits long One Master code One Engineer code 29 user codes Additional duress code for each user cod
5. and LED 2 Press 4 0 Lockout Time setting Enter 1 2 Unit displays value of Lockout Time with buzzer and LED 2 If you want to exit Lockout Time setting press To enter new value press new Lockout Time value If value of Lockout Time is programmed as 0 seconds lockout will not be active Example If you want to enter new Lockout Time value of 80 seconds press 1 2 in Engineer programming mode Unit displays current value of Lockout Time with buzzer and LED 2 Press 8 0 buttons Relay 1 Default Time Enter 1 3 Unit displays value of Relay 1 Time with buzzer and LED 2 If you want to exit Relay 1 Default Time setting press To enter new value press new Relay 1 Default Time value Example If you want to set new Relay 1 Default Time value to 10 seconds press 1 3 in Engineer programming mode Unit displays current value of Relay1 Default Time with buzzer and LED 2 indications Press 1 0 4 To exit Engineer programming mode press Relay 2 Default Time Enter 1 4 Unit displays value of Relay 2 Default Time with buzzer and LED 2 To exit Relay 2 Default Time setting press To enter new value press new Relay 2 Default Time value Example If you want to set new Relay 2 Default Time value to 9 seconds press 1 3 in Engineer programming mode Unit displays current value of Relay 2 Default Time with buzzer and LED 2 signa
6. output status Green indicates Relay 1 status 12 Integrated Technical Vision Ltd http www itvsystems com ua Control Panel Operation LED 3 Green indicates Relay 2 status Programming mode LED 2 Bi colour Red and Green indicates access levels and user code options and numeric values of unit settings LED 3 Green indicates access levels and user code options Door time Door time starts after relay activation The first break and closing of the door sensor ends door time The warning signal sounds if door is opened for five seconds before door time ending In this case you should close the door and enter code once more to start door time again The door time is programmed by means of an Engineer code Valid values are 0 253 seconds Open door state After code with door time set to 254 sec entering the door will not be supervised for unlimited time until it is closed Lockout Mode If invalid code is entered for three times the unit locks out for programmed time Lockout time can be programmed from 1 to 255 seconds Programming this value to 0 disables lockout mode http www itvsystems com ua Integrated Technical Vision 13 Programming Control Panel Operation DLK 640Plus can operate in one of the following modes Main mode Day mode Night mode button programming mode Engineer code programming mode Master code programming mode Lockout mode LED 1 red continuously lights in th
7. used the unit automatically switches to Engineer code programming Enter desired user code 1 9 7 5 If code is accepted buzzer emits long beep If an error occurred several short beeps would be heard By default new code has the following settings Code drives Relay 1 Relay Time 255 default Relay times Door Time 255 default door time http www itvsystems com ua Integrated Technical Vision 17 Engineer code programming mode Access level 3 Press key 1 Green LED 2 switches OFF that means code does not drive Re lay1 Press key 2 LED 3 switches ON that means code drives Relay 2 Press key 4 Buzzer emits continuous beep that means unit is ready for Relay Time editing Press keys 1 9 Buzzer emits continuous beep that means unit has accepted new value of Relay Time Press key 5 Buzzer emits continuous beep that means unit is ready for Entry Time editing Press keys 5 5 Buzzer emits continuous beep that means unit has accepted new value of Entry Time Press key to return to Engineer code programming mode Enter 1 2 Buzzer sounds continuous beep and then displays previously pro grammed Lockout Time Press continuous beep sounds unit is ready for Lockout Time editing Press 0 continuous beep sounds changes are accepted Press continuous beep sounds and the unit quits Engineer programming User code viewing and editing Press 3 then code numb
8. 2 3 beeps interval 5 blinks of LED 2 5 beeps Digit 0 is displayed as one long sound and LED 2 flash For instance number 040 is displayed as follows LED 2 lights long sound interval 4 blinks of LED 2 4 beeps interval LED 2 lights long sound Parameters are displayed with LED2 and LED3 Green light of LED 2 means YES Hardware reset to factory defaults To reset DLK 640Plus to factory defaults perform the following actions 1 Cut off the power 2 Short jumper J1 3 Power on the unit Buzzer will sound three long beeps then several short beeps accom panied by LEDs blinking The settings corre spond to factory defaults and the pan el is in Engineer programming mode now O After resetting to factory defaults all user codes will be deleted 4 Take off jumper J1 with power on Program desired settings D 17 g a gt xe 6 g http www itvsystems com ua Integrated Technical Vision 15 Engineer code programming mode Engineer code programming mode Enter Engineers code factory setting 1 2 3 4 to switch to Engineer code programming mode Buzzer will sound several times accompanied with LEDs blinks LED 1 blinks during the whole period of programming Engineer code can be changed as described in Code change with button Engineer code programming mode is described in APPENDIX Engineer code programming flowchart After Engineer code programming mode engaging y
9. 2 button sound signal confirms state change and LED 3 switch on off User code review Press 9 DLK 640Plus displays current User Code with buzzer and LED 2 To return to Master programming press To exit Master code programming press again O Ifthere are no keystrokes during 40 seconds the unit automatically exits program ming mode Example You need to change code 4 to 1 9 7 5 make it active valid 24 hour allow user to change it Enter Master Code The panel emits several beeps accompanied with LED 2 blinks Enter Code Number 4 unit emits long beep If code 4 is not programmed sounds error signal several short beeps will be heard If you want to set access level 2 code is active valid 24 hour and user can change it make LED 2 OFF and LED 3 ON by pressing keys 1 and 2 accordingly To change code press key 0 three short beeps will sound Enter 1 9 7 5 one log beep sounds If the same user code or duress code exists error signal sounds Press Long sound is emitted and the unit returns to main mode 20 Integrated Technical Vision Ltd http www itvsystems com ua Chief code programming mode button programming mode Any user can change his own code with command if the code has access level 2 or 4 Enter Buzzer sounds 3 times together with LED 1 blinking Enter Old User Code then New User Code and confirm New User Code New code is acce
10. Stand alone access control DIK640Plus stand alone access control panel Integrated Technical Vision Ltd http www itvsystems com ua This manual covers installation programming and utilization of DLK 640Plus stand alone access control unit Read this manual carefully prior to installing and pro gramming the unit Design Change Disclaimer Due to design changes and product improvements information in this manual is subject to change without notice ITV reserves the right to change product design at any time which may subsequently affect the contents of this manual ITV assumes no responsibility for any errors that may appear in this manual ITV will make every reasonable effort to ensure that this Installation Programming Manual is up to date and corresponds with the unit you purchase Reproduction Disclimer All rights to this document preserved by Integrated Technical Vision Ltd Copying printing and any other kind of reproduction of the document or its part without permission of Integrated Technical Vision Ltd is prohibited Trademarks ITV is a registered trademark of Integrated Technical Vision Ltd Training and technical support Integrated Technical Vision Ltd performs training on the installation programming and utilisation of DLK 640Plus stand alone access control unit For additional in formation about the training and discussing of your particular requirements to the unit please contact our personnel by the ph
11. access to the premises as two different codes control Relay1 and Relay2 But high priority user code can have permission for individual door opening 24 Integrated Technical Vision Ltd http www itvsystems com ua Programming APPENDIX 1 Alarm output time 10sec Lockut time 40sec Engineer code 1234 Master code 5678 User code 2 AAAA access level 2 valid 24 hour can be changed by user relay 2 control door time 30 sec User code 3 3333 access level 4 valid day mode cannot be changed by user relay 2 control door time 30 sec User code 4 4444 access level 2 valid 24 hour can be changed by user relay 2 control door time 30 sec User code 5 5555 access level 2 valid 24 hour can be changed by user both relay control door time 30sec A door can be opened after code 5 or code 3 4 entry in the above given exam ple http www itvsystems com ua Integrated Technical Vision 25 APPENDIX 1 Panel Use in Security systems DLK640Plus allows automatic setting unsetting of security system by means of user code entry Example Codes with Relay 1 control permission are responsible for setting unset ting of the system and codes with Relay 2 control are responsible for access to the premises The wiring is shown on Figure below 680606060606060666 12V GND RTE DC I O SAB ALM CM1NC1 NO1 CM2 NC2 NO2 other devices tamper connection setting unsetting input connection Doo
12. ccess level 3 Default Relay 1 time 3 sec 14 Integrated Technical Vision Ltd http www itvsystems com ua Programming Default Relay 2 time 3 sec Default door time 20 sec Factory default of user code 2 A A A A consists of several hexadecimal digits A This is made intentionally to avoid code entry from keypad after factory defaults resetting but RTE button should be available for use Default times There are tree default times Relay 1 Default time Relay 2 Default time and Door Default time made for convenience of programming the unit You can refer to these values while programming parameters of users codes In this case by changing only default time value you will change the appropriate values for all codes For instance if you enroll new user code its relay time will be automatically set to 255 It means that as value of relay time for this code the default relay time will be used If you set the value of relay time to 255 for several codes it means that you use the default relay time for all these codes Modifying Default Relay Time you change the time of relay activation for all these codes Settings displaying Numeric values of settings are displayed by means of built in buzzer and LED 2 Nonzero digit is displayed as number of short beeps and LED 2 blinks Digits are separated by interval For instance number 235 will be displayed as follows 2 blinks of LED 2 2 beeps interval 3 blinks of LED
13. e Two access levels Two relays Alarm output Door sensor RTE sensor Tamper Voltage 10 15V Power consumption Stand by 15mA Maximal 70 mA Contact Rating Relay 5A 24V Alarm Output 60 mA 24V Voltage ripple 500mV 12V Weight 200 grams Dimensions 156 x 105 x 20 mm Temperature 0 55 C Relative humidity 80 at 25 C without condensate Integrated Technical Vision Ltd http www itvsystems com ua Operation Operation General Configuration The view of DLK 640Plus stand alone access control panel is shown on Figure 1 1 LED1 2 LED2 3 LED3 4 built in keypad 5 blank end cover 6 control unit PCB 7 keypad PCB 8 front cover http www itvsystems com ua Integrated Technical Vision 7 Operation Terminals Layout Terminals layout on the main board is shown on Figure 2 below Keypad PCB Panel baseplate N Door sensor RTE button 12 V power 8 Integrated Technical Vision Ltd http www itvsystems com ua Operation Terminals Assignement 12V GND 12V power supply connection terminals RTE request to exit button connection terminals DC door sensor connection terminals I O LED 2 external management red light SAB tamper connection terminal ALM transistor alarm output for external unit connection NO2
14. e main mode The unit performs actions pro grammed for entered code in this mode These actions are Relay 1 activation Relay 2 activation activation of both relays or opportunity to choose relay for acti vation Night mode of the unit is indicated by slow blinks of LED 1 Only codes with access level 2 are valid in this mode To switch the unit into night mode enter code without control over any relay per mission see Engineer programming mode This code should have access level 2 otherwise the code will be able to switch night mode on but unable to switch a unit into day mode If duress code is entered DLK 640Plus performs actions accordingly to user code access level and options and switches on alarm output for programmed time Alarm output switches on immediately after duress code entry O If there are no keystrokes for 40 seconds a unit returns to the main mode automat ically Program desired settings and codes before utilizing the unit Programming O During programming DLK 640Plus stand alone access control unit ignores break opening of RTE button Door sensor control lasts as usual Factory defaults After the first switching on and after reset to factory defaults DLK 640Plus works in the main mode with the following settings Alarm output time 10sec Lockout time 40 sec Engineer code 1234 Master code 5678 User code 2 AJIAJIAJ A Code drives Relay1 Relay time 3 sec Door time 15 sec A
15. er OR user code DLK 640Plus displays user code Pressing of will return you to Engineer programming pressing of allows to enter new user code Example If you want to change user code 3 to 0 6 1 1 7 5 in Engineer code programming mode Press 3 the panel displays user code Press then 0 6 1 11 7 5 1 User code deletion Enter 4 then code number OR user code Example If you want to delete user code 17 press 4 then 1 7 Panel s reset to factory defaults Enter 5 then Engineer code After performing of this operation all previously programmed user codes are delet ed and Engineer code Master code and code 2 are programmed according to factory defaults Example If Engineer code is 1 9 8 8 and you want to reset DLK 640Plus stand alone access control panel to factory defaults press 5 Buzzer utters nine sound signals Enter Engineer code 1 9 8 8 Alarm output activation time Enter 1 1 Unit displays value of alarm output time with buzzer and LED 2 Press to exit alarm output time setting Press new Alarm Time value to enter new value 18 Integrated Technical Vision Ltd http www itvsystems com ua Engineer code programming mode Example lf you want to enter new Alarm Time value of 40 seconds press 1 1 in Engineer programming mode Unit displays current value of alarm output time with buzzer
16. he current supply voltage of the coil 10 Integrated Technical Vision Ltd http www itvsystems com ua Operation Note the fact that some cheap electric door strikes are not intended for been energized for a prolonged time Program relay time as short as possible to avoid door strike coil overheating Read installation manual carefully before connecting a lock or door strike or be fore programming its operation parameters Ensure that your power supply is pow erful enough to drive lock or door strike If lock or door strike requires 12 VDC power you can connect it in parallel with DLK 640Plus stand alone access control unit otherwise you would have to install additional power supply for locking de vice It is recommended to consult the manual of the locking device before its installa tion Sirens and Bells Some sirens require polarity observing Often Electric bells are the inductive load for power supply Connecting the bells observe the warning about the inductive load above Alarm output Alarm output is an open collector transistor output It grounds during activating You can utilize alarm output connecting it to the outer alarm system or the execut ing device with operation current less than 60 mA If door contact is connected to DC terminal alarm output will activate any time the door is opened except entry time Alarm output activates for the programmed alarm time from 1 to 254 seconds If alarm time is progra
17. ls Press 0 9 To exit Engineer programming mode press Default Door Time Enter 1 5 Unit displays value of Default Door Time with buzzer and LED 2 To exit Default Door Time setting press To enter new value press new Door Time Default value Example To set new Default Door Time value to 5 seconds press 1 5 in Engineer programming mode Unit displays current value of Default Door Time with buzzer and LED 2 Press 0 5 Press to exit Engineer programming mode http www itvsystems com ua Integrated Technical Vision 19 Chief code programming mode Master code programming mode To switch to Master code programming enter Master Code Factory default for Master code is 5 6 7 8 DLK 640Plus stand alone access control pan el emits several beeps accompanied by LED 2 and LED 3 blinks User code settings editing Enter User Code number or User code Access level for a code is dis played by LED 2 and LED 3 2 3 is own code mode Dorr OFF active NO NA gt ON on OFF Acive no Day omw User code change Press 0 Unit beeps three times Enter New User code and confirm with New User code New code will be accepted if it does not coincide with any existing user code or duress code LED 2 switch on off Press 1 button sound signal confirms state change and LED 2 switches on off LED 3 switch on off Press
18. me for it any warranty or liability concerning this product In no event shall Integrated Technical Vision Ltd be liable for any direct indirect or consequential damages Loss of anticipated profits loss of time or any other loss es incurred by the buyer in connection with the purchase installation or operation or failure of this product http www itvsystems com ua Integrated Technical Vision 31 32 Integrated Technical Vision Ltd http Awww itvsystems com ua 030203
19. med for user code 2 Removal of user code 2 causes alarm output activation O If RTE button is pressed more than 8 seconds alarm output activates IN Door sensor OMT MOMO BOO DLK 640Plus determines door sta GNDRTE DC I O SAB ALMCM1 tus by means of door sensor If you do not use door sensor the unit can not detect neither door forcing nor door left opened for a long time The wiring of door sensor and RTE RTE button Door button is shown on Figure 5 Door sensor Figure 5 sensor has normally closed con tacts while RTE button must have normally open contacts O Itis advisable to equip the door with mechanical door closer Electric locks and door strikes The unit has two relays with normally opened and normally closed contacts for energizing or de energizing electric locks door strikes etc Relays are activated after valid code introduction Relays can work in triggering mode program the relay time for 0 sec in this case relay changes its state on each valid code entry Relays can also be activated for the programmed time from 1 to SAB ALM CM1NC1 NO1 CM2 NC2 NO2 254 sec You can program relay activation time for each code individually Q Relay contact commutation is 5A 24 Volts Commutation of the inductive load electric lock for instance causes high energy electric impulse induced through relay con tacts If you want to save con tacts from damage protect them with diode connected in reverse to t
20. mmed for 0 seconds alarm output will never be active If alarm time is programmed for 255 seconds alarm output is activated until Master or Engineer code is entered Alarm time can be programmed by means of Engineer code Code Entry Code is entered by sequential keys depressing on the keypad Code length can vary from 4 to 10 digits Code entry is followed by pressing button Each key pressing is accompanied by the sound of internal buzzer Valid code is accompa nied by one long sound signal Entering of invalid code is warned by several short sounds If invalid code is entered three times DLK 640Plus stand alone access control unit blocks itself for the programmed time Blocking is indicated by rapid blinking of red LED 2 You can cancel entereded digits succession with button pressing in case of mistake If no key is pressed during 40 seconds all previously entered digits arre discarded and the unit switches into main mode http www itvsystems com ua Integrated Technical Vision 11 Operation Codes Several types of codes are intended for unit control Code 00 is Engineer code It allows Engineer Code programming Master Code programming Users codes programming Relay operation modes and door time programming individually for each user code Alarm output time programming Keypad lockout time programming Reset to factory defaults Code 01 is Master code It allows Master Code
21. o be followed by Remarks s Code drives Relay 1 if LED 2 1 Code drives Relay1 aaa is ON Code drives Relay 2 if LED 3 2 Code drives Relay2 ee is ON 3 Choice of relay after EA Both LED 2 and LED3 blinking Code for choice sa Enter Relay Time 0 trigger mode 4 Relay Time Editing 255 default value 0 no entry time 254 opened door mode 255 default value Enter Door Time Entry Time Editing value 5 6 9 0 Reserved ooo i Time displayed with buzzer and El fia t ey EG LED 2 3 Time displayed with buzzer and s1 Enty tme aispey ES Press 1 to switch 7 Switch to Access level LED 2 pate ee ee setting Press 2 to switch f levels for exit LED 3 You can edit access level of the code after pressing see Table 2 Table 2 level 1 2 is own code mode 1 orF orF met no N A 2 orF ON active Ys 24hou 3 ON OFF Active no Day on a on on Active ves Dayton Press to exit access level editing Press to exit editing of user code settings Example To program new user code 1 9 7 5 driving Relay 2 with Relay Time 19 sec Door Time 55 sec and lockout OFF perform the following actions Enter Engineer code Buzzer sounds several beeps accompanied with LEDs 2 and 3 blinking During programming LED1 blinks RED Enter 1 Vacant user code will be displayed with buzzer and LED 2 If all codes are
22. one numbers below For the personnel intended for sales and installation of DLK 640Plus stand alone access control unit on permanent basis is recommended to pass the training in Integrated Technical Vision Ltd Technical support for all products of Integrated Technical Vision Ltd can be ob tained at working time by the phones 380 0 44 248 65 88 380 0 44 248 65 89 380 0 44 248 65 90 This support assumes the calls of trained specialists End users must apply to their dealers or installers before calling us This information is available on our web site www itvsystems com ua http www itvsystems com ua Integrated Technical Vision 3 Contents POGUES ns eeaeee aeae aeea a nats a a cela head pia aeaaeae cent 6 Operaatio M AAA A 7 MON it 9 Request to Exit RTE Button ooooooonnnoccccccnnonocccccnnnono cc cn nana non cc cnn nnnrnnns 10 Door Sensor iii A aida 10 Electric locks and door strikes ooooocooonnicccocnnonnncccannnnnononno na nnr crono nn rra 10 Duress Code coccion ad dde 12 LEDS curo tota daa a Dll a tt 12 Control Panel Operation Manon adasdiad 14 o A A a EAEE 14 Factory default icici diene ias 14 Default imes cunt de a tc as 15 Settings displaying incurniciata i ee ed heed beled el 15 Hardware reset to factory defaults 00 eee eeecee cence cere eeenneeeeeeeeenaeeeeeeeeenaaees 15 User code settings editing eee ecceceeeeeeeeeeeeeeeeeeeeeeeeeaeeeeeeseeeeeeeeeeteeeaaaees 20 User code Chang Gs
23. ou acquire the following pos sibilities Master code programming Enter 0 then new Master code and confirm it Master code New code will be accepted if it differs from any enrolled users codes and duress codes Example To change Master code to 7777 in Engineer programming mode enter 0 then 7 7 7 7 and once more 7 7 7 7 Users codes enrollment Enter 1 DLK 640Plus displays the first not used user code number with buzz er and LED 2 indications Enter User Code After that you can change code settings or move to Engineer programming mode by pressing Default settings of new code are Code drives Relay 1 Relay Time is 255 default time Door Time is 255 default time Access level 3 To view or change settings press appropriate key see Table 1 To exit user code settings editing mode press button User code settings editing Enter 2 Then enter number of user code OR User Code and press FF LEDs 2 and 3 indicate relay operation setting for this code Press appropriate key for parameters change see Table 1 The default value of relay time is used if you need to set equal time for many user codes If you are using default time changing of these values causes changes of time for all user codes relevant to them 16 Integrated Technical Vision Ltd http www itvsystems com ua Engineer code programming mode Key Function T
24. programming Users codes and their access level programming Codes 02 30 are users codes They can be allowed to Drive relays Switch day night modes Entering of the user code 2 is identical to RTE button pressing Changing of settings of user Code 2 causes changing of RTE button settings Deletion of user code 2 causes alarm output activation after RTE button depressing For each user code you can program Access level from 1 to 4 define access rights programmed by Master code Code options choose relays to drive relay time door time programmed by Engineer code Duress Code Every user besides his regular code has an additional duress code independent ly of user code access level and options When this code is entered DLK 640Plus stand alone access control unit grants access accordingly to user code access level and options and alarm output switches on Duress code differs from user code in the last digit per 1 For instance if user code is 1 2 3 4 than duress code for this user is 1 2 3 5 If user code ends with 9 than duress code ends with 0 For instance if user code is 1 0 0 9 than duress code for this user is 1 0 0 0 LEDs There are three LEDs on the front panel of DLK 640Plus stand alone access con trol unit Their functioning is described below Main mode LED 1 red indicates panel operation mode LED 2 Bi colour Red and Green Red indicates I O
25. pted if code changing is allowed and new code is not identical to any enrolled users or duress codes Press to exit code programming Master code and Engineer code are changed in the same way O If there was no keystrokes during 40 seconds unit returns to main or restricted mode In this case user code does not change Example User has code 1 2 3 4 5 and wants to change code to 4 3 2 1 O In this case access level of the code should be 2 or 4 Press three beeps sound and LED 2 flashes RED Enter old user code 1 2 3 4 5 long beep sounds If code has access level 2 or 3 error signal sounds one long and two short beeps Enter new user code 4 3 2 1 long beep sounds If the same user code or duress code exists error signal sounds and unit quits the code programming Confirm by entering 4 3 2 1 long beep sounds and the panel switches to the main mode http www itvsystems com ua Integrated Technical Vision 21 APPENDIX 1 APPENDIX 1 Access Control System DLK 640Plus can be used for access to a single room control The wiring is shown on figure below 608060096 006060060006 12V GND RTE DC I O SAB ALM CM1NC1 NO1 CM2 NC2 NO2 other facilities tamper connection outer security system input connection Door sensor 12V power supply RTE button In this example Relay 1 is used to energize electric lock Terminals wiring i
26. r sensor 12V power supply RTE button 26 Integrated Technical Vision Ltd http www itvsystems com ua APPENDIX 1 Programming Alarm output time 3sec Lockout time 40sec Engineer code 1234 Master code 5678 User code 2 AAAA access level 4 valid day cannot be changed by user relay 1 control relay time 10sec door time 30 sec User code 3 3333 access level 4 valid day mode cannot be changed by user relay 1 control relay time 10sec door time 30 sec User code 4 4444 access level 2 valid 24 hour can be changed by user no relay control door time 0 sec User code 5 5555 access level 2 valid 24 hour can be changed by user relay 2 control relay time Osec door time Osec Enter user code 5 and switch it from day to night mode by means of code 4 to set the system If you want to unset the system change day mode to night using code 4 and enter user code 5 Code 3 or RTE button code 2 can open a door only in day mode http www itvsystems com ua Integrated Technical Vision 27 82 p uoisi eoruyoa pae169 u main mode 00 master code change gt new code gt new code H01 code enrollment vacant code number _ 02 code parameter editing engineer code code number or code code number code E or codel introduction C
27. s shown for the lock locked while been deenergized Using the lock which is unlocked while been deenergized connect it to NC terminal You can use Relay 2 terminals for additional devices engaging The input can be used for 24 hours if door time for all codes is set to 0 22 Integrated Technical Vision Ltd http www itvsystems com ua APPENDIX 1 Programming Engineer code 1234 Master code 5678 Alarm output time 10 sec Lockout Time 40 sec User code 2 AAAA access level 2 valid 24 hour can be changed by user relay 2 control door time 30 sec User code 3 3333 access level 4 valid day mode cannot be changed by user relay 2 control door time 30 sec User code 4 4444 access level 2 valid 24 hour can be changed by user relay 2 control door time 30 sec http www itvsystems com ua Integrated Technical Vision 23 APPENDIX 1 High Degree Security Access Control System DLK 640Plus access control panel can be used for control of access to highly secured premises In case of relay 1and 2 terminals series connection access to the premises will be granted after two different codes consecutive entry The wir ing is shown on figure below 606060609069 06006 12V GND RTE DC l O SAB ALM CM1NC1 NO1 CM2 NC2 NO2 other facilities tamper connection outer security system input connection Door sensor 12V power supply RTE button Presence of two people is demanded for
Download Pdf Manuals
Related Search