10.8V Multi Function tool
Contents
1. AFTER SALES SUPPORT 0203 5142281 1800 719901 www servotool eu WOC 1013 gt 2 070 KA Ng 7 Electrical safety the rating plate Also check that your mains voltage corresponds to the input Always check that the voltage on the machine corresponds to the voltage on voltage of the battery charger E The machine is double insulated therefore no earth wire is required lt Do not use the machine if the mains cable or the mains plug is damaged lt Only use extension cables that are suitable for the power rating of the machine with a minimum thickness of 1 5 mm If you use an extension cable reel always fully unroll the cable Mains plug replacement If the moulded 3 pin plug attached to the unit is damaged and needs replacing it is important that it is correctly removed and replaced by an approved BS 1363 13A fused plug and that the following wiring instructions are followed The wires in the mains cable are coloured in accordance with the following code blue neutral brown live As the colours of the wires in the mains cable of the unit may not correspond to the coloured markings identifying the terminals in the plug proceed as follows lt The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black lt The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red AFTER SALES SUPPOR2. away from damp and wet conditions lt If any wires on the charger are damaged do not use it until these have been replaced lt When the charger is not in use it should not be plugged in When unplugging do not pull the plug out by the cable lt Ifthe charger breaks down or suffers from other technical problems take it to a recognised dealership to be checked before using it again Any damaged parts must be replaced lt Take care when handling the accumulator block do not drop it or knock it against other things lt Never attempt to repair the battery charger or accumulator block yourself this can be extremely dangerous Repairs should always be carried out by a recognised dealership lt Always unplug the charger before cleaning or carrying out any other maintenance onit lt Do not attempt to charge the accumulator block in temperatures of below 5 degrees or above 40 degrees centigrade lt Never throw the accumulator block into water or a fire it may explode lt Donot shortcut the 2 contactpoints on the bottom of the machine This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance
3. 10 8V MULTI FUNCTION TOOL ORIGINAL MANUAL Now you have purchased a Workzone product you can rest assured in the knowledge that as well as your 3 year parts and labour guarantee you have the added peace of mind of dedicated helplines and web support Contents 03 Introduction 04 General Information and safety instructions 09 Assembly and parts list 14 Instructions 15 FAQ 18 Other useful information 22 CE Declaration 23 Warranty card AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwservotool eu WOC 1013 WOC 1013 Congratulations You have made an excellent choice with the purchase of this quality Workzone product By doing so you now have the assurance and peace of mind which comes from purchasing a product that has been manufactured to the highest standards of performance and safety supported by the high quality standards of ALDI We want you to be completely satisfied with your purchase so this Workzone product is backed by a comprehensive manufacturer s 3 year warranty and an outstanding after sales service through our dedicated Helpline We hope you will enjoy using your purchase for many years to come If you require technical support or in the unlikely event that your purchase is faulty please telephone our Helpline for immediate assistance Faulty product claims made within the 3 year warranty period will be repaired or replaced free of charge provided that you have satisfactory pr
4. 80 sanding paper 1 Diamond saw blade 1 HSS segment saw blade 1 Allen key 1 Sanding plate 1 Instruction manual 1 Quick start quide 1 After Sales support card Check the appliance any loose parts and accessories for damage caused during transport 19 AFTER SALES SUPPORT 0203 5142281 mb 1800 719901 wwwservotool eu WOC 1013 20 AFTER SALES SUPPORT 0203 5142281 mb 1800 719901 wwwservotool eu WOC 1013 21 AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwservotool eu WOC 1013 i KA ee 7 CE DECLARATION OF CONFORMITY 7 We declare under our sole responsibility that this product WOC 1013 10 8V Multifunction tool is in conformity and accordance with the following standards and regulations EN60745 1 EN60745 2 4 EN55014 1 EN55014 2 EN61000 3 2 EN61000 3 3 EN60335 1 EN60335 2 29 2006 42 EC 2006 95 EC 2004 108 EC 2002 95 EC 2002 96 EC 01 11 2011 ZWOLLE NL Authorized to compile the technical file a YU CEO Ferm BV It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice Ferm BV Lingenstraat 6 8028 PM Zwolle The Netherlands 22 AFTER SALES SUPPORT 0203 5142281 mb 1800 719901 wwwservotool eu WOC 1013 KA Ng 007 WWORK70 X15 10 8V MULTIFUNCTIONAL TOOL Your det
5. T 0203 5142281 mb 1800 719901 www servotool eu WOC 1013 gt 2 070 KA Nang Assembly and parts list 3 Fig 1 On Off switch Speed control Sanding sole Diamond saw blade Sandpaper Scraper E cut saw blade Segmented HSS saw blade SON UT AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwsservotool eu WOC 1013 1 13 Before assembly always switch off the machine and remove the mains plug from the wall outlet Position 1 7 13 4 14 27 28 4 29 32 33 35 36 37 1 www servotool eu Description Battery 10 8V Switch Bar Scraper Ring Screw Half round cutting blade Plunge cutting blade Sanding pad Charger complete Diamond saw blade 10 AFTER SALES SUPPORT 0203 5142281 b 1800 719901 Fig 2 A Part no 102914 102906 102907 102908 102909 102910 102911 102912 102913 1 13 5 www servotool eu 1800 719901 T 0203 5142281 AFTER SALES SUPPORT 11 Accessories Fig 1 4 5 Sanding sole Sanding near edges corners and hard to reach areas Depending on the sanding paper for sanding of wood paint varnish and stone 6 Scraper Scraping on solid underground For instance removal of glue carpets and tiles carpet flooring 7 E cut sawblade Separating and deep plunge cuts for sawing close to edges in corners and hard t
6. ails Name Address an E mail Date of purchase We recommend you keep the receipt with this warranty card Location of purchase Description of malfunction Return your completed warranty card to AFTER SALES SUPPORT Circuit Tech Ltd Ws ee m www servotool eu Units 1 9 Stanley Mill lt Kirkebrok Road lt Deane Bolton Lancs England 813 4JE MODEL WOC 1013 05 2012 50612 Contact and internet www servotool eu Fax 44 0 1204 659607 YEAR WARRANTY 1201 8
7. ce to hold work It s safer than using your hand and it frees both hands to operate the tool 4 Power tool use and care a Donot force the power tool Use the correct power tool for your application The correct power tool will do the job better and more safely at the rate for which it was designed b Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired AFTER SALES SUPPORT 0203 5142281 1800 719901 www servotool eu WOC 1013 gt 2 70 KA Ng c Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally d Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tools operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools f Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into ac
8. count the working conditions and the work to be performed g Damaged switches must be replaced at a customer service repair centre Do not use power tools that cannot be switched on and off h Do not leave power tools unattended while they are switched on Always switch off the tool and wait until it has come to a full standstill before leaving i Ifthe mains cable has been damaged it must be replaced by a suitably qualified person with a special mains cable These can be obtained from the manufacturer or the manufacturer s customer service department 5 Battery tool use and care a Ensure the switch is in the off position before inserting battery pack Inserting the battery pack into power tools that have the switch on invites accidents b Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack c Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire d When battery pack is notin use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause burns of a fire e Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush
9. d to operate over a long period of time with a minimum of maintenance Continuous satisfactory operation depends upon proper machine care and regular cleaning Cleaning Keep the ventilation slots of the machine clean to prevent overheating of the motor Regularly clean the machine housing with a soft cloth preferably after each use Keep the ventilation slots free from dust and dirt If the dirt does not come off use a soft cloth moistened with soapy water Never use solvents such as petrol alcohol ammonia water etc These solvents may damage the plastic parts Lubrication The machine requires no additional lubrication Faults Should a fault occur e g after wear of a part please contact the service address on the warranty card On page 10 and11 of this manual you will find an exploded view showing the parts that can be ordered Environment To prevent damage during transport the appliance is delivered in packaging which consists largely of reusable material Therefore please make use of options for recycling the packaging 15 AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwservotool eu WOC 1013 gt 2 070 KA Ng X Faulty and or discarded electrical or electronic apparatus has to be disposed of at the appropriate recycling locations Do not dispose of power tools into domestic waste According to the European Guideline 2002 96 EC for Waste Electrical and Electronic Equipment and its implementatio
10. n into national right power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way The product and the user manual are subject to change Specifications can be changed without further notice Li ION batteries can be recycled Drop them off at a disposal center for Melee chemical wastes so that they can be recycled or disposed of in environmentally manner Do not dispose of batteries into domestic waste 16 AFTER SALES SUPPORT 0203 5142281 mb 1800 719901 www servotool eu WOC 1013 FAQ gt Trouble shooting Below we have listed a few probable causes and solutions to which you can refer if your machine does not function properly Fault Solution 1 fails to operate Power turned off Change the battery The electric motor fails to reach Battery power is too low maximum speed Recharge the battery Machine overheats Air vents are blocked Clean them with a dry cloth The machine has been overloaded Use the machine for the purpose for which it was intended Excessive sparking or electric motor There s dirt inside the motor or the runs irregular carbon brushes are worn Replace the carbon brushes or bring the machine to a specialized repair centre 17 AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwsservotool eu WOC 1013 gt 2 070 KA ee Technical specifications Charger input 220 240V Cha
11. n on the illustration Pay attention to and pole markings lt Insert the charger plug into a power socket The red rapid charging light and green light should now be illuminated lt As soon as the red light turns off charging has been completed and the device is ready for operation Only the green light is now illuminated Only use the charger in a dry environment at temperatures between 5 and 40 C 14 AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwservotool eu WOC 1013 gt 2 070 KA Ng 777 The battery in your machine was not charged up at the factory Before using it for the first time you should charge it for approx 3 5 hours so that it reaches full capacity The final capacity of the battery is reached after 4 5 battery cycles One advantage of using Lithium lon batteries is that until the battery is almost empty hardly any power fading is noticeable The machine can be used until you start noticing that the power is elapsed The battery is discharged now and needs to be charged Lithium lon cells can be stored for a long period without losing much of their charge When the machine is not being used over a longer period of time it is best to store the battery in charged condition When the machine is not being used over a longer period of time the battery has A to be charged fully first The battery has to be stored in charged condition These machines have been designe
12. o reach areas wooden materials soft materials 8 Segmented HSS saw blade Separating and deep plunge cuts for sawing close to edges in corners and hard to reach areas Hard and soft wood plastic non ferrous metals Mounting accessories For saw blades scrapers and disc cutters and cutting discs use the clamping screw in combination with the retaining ring lt Remove the clamping screw using an Allen key lt Replace the tool and tighten it using the clamping screw Check that the tool is secure in the chuck and that the machine is correctly secured and supported Fitting replacing sandpaper Using hook and loop fastening system lt Place the sandpaper in the middle of the sanding disc and press it firmly with your hand lt Press the sandpaper firmly onto the plate with brief firm pressure and then switch on the machine This ensures that the disc is correctly secured and prevents excessive wear lt Ifthe sandpaper is worn in a particular spot you can remove it turn it 120 and refit it or replace it Warning Switch the machine off and unplug the machine before mounting the accessories 12 Bee 70 AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwservotool eu WOC 1013 gt 2 2 0 KA Ng Connecting and removing the battery Ensure that the exterior of the battery block or tool is clean and dry before connecting the charger lt Insert the battery into the base of the a
13. oof of purchase keep your till receipt safe This does not affect your statutory rights However be aware that the warranty will become null and void if the product is found to have been deliberately damaged misused or disassembled AFTER SALES SUPPORT 0203 5142281 mb 1800 719901 wwwservotool eu a 070 gt 2 KA ee General Information and Safety Instructions 2 For your own safety and that of others we recommend that you read this instruction manual carefully before using this machine Keep this instruction manual and the documentation provided with the machine for future reference Explanation of the symbols Denotes risk of personal injury loss of life or damage to the tool in case of non observance of the instructions in this manual Indicates electrical shock hazard Contact with or inhalation of dust generated during use e g lead painted surfaces wood and metal can endanger your health and the health of bystanders Always wear appropriate protective equipment such as a dust mask Always use proper dust extraction during use Wear safety goggles Wear hearing protection 3D 2 e General safety instructions Warning Read all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings listed below refers to your mains operated corded power tool or battery opera
14. ppliance as shown on the illustration Push the battery until it latches in lt Press the locking buttons on both sides before removing the battery and disengage the battery from the base of the appliance 13 AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwservotool eu WOC 1013 gt 2 070 Instructions Ea Setting the speed Fig 1 The speed can be set from slow to fast using the continuous speed adjustment wheel 2 Switching on lt Push the switch 1 forward to position Switching off lt Push the switch 1 back to position Hints for optimum use Clamp the workpiece Use a clamping device for small workpieces lt Drawa line to define the direction in which to guide the accessory lt Firmly hold the machine by the grip lt Switch on the machine lt Wait until the machine has reached full speed lt Place the accessory on the workpiece lt Slowly move the machine along the pre drawn line firmly pressing the accessory against the workpiece lt Do not apply too much pressure on the machine Let the machine do the work lt Apply less pressure when the machine starts to vibrate heavily lt Switch off the machine and wait for the machine to come to a complete standstill before putting the machine down Make sure that the machine is not live when carrying out maintenance work on the motor Charging the battery Place the battery inside the charger as show
15. rger frequency 50 Hz Charger output 10 8V Battery capacity 1 3 Ah Charging time 3 5 hours No load speed 5 000 19 000 min Oscillating angle 3 degrees Weight 1 48 kg Sanding LpA Sound pressure level 80 5 3 dB A LwA sound power level 91 5 3 dB A Vibration 4 380 1 5 m s Polishing LpA Sound pressure level 82 1 3 dB A LwA sound power level 93 1 3 dB A Vibration 5 389 1 5 m s Vibration level The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 60745 it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned lt using the tool for different applications or with different or poorly maintainted accessories may significantly increase the exposure level lt the times when the tool is switched off or when it is running but not actually doing the job may signifi cantly reduce the exposure level Protect yourself against the effects of vibration by maintaining the tool and its accessories keeping your hands warm and organizing your work patterns 18 AFTER SALES SUPPORT 0203 5142281 b 1800 719901 wwwservotool eu WOC 1013 gt 2 Contents of packing 1 Oscillating tool 1 Charger 1 Battery 1 Plunge saw blade 1 Scraper 5 G60 sanding paper 5 G80 sanding paper 5 G120 sanding paper 5 G1
16. ted cordless power tool Save these instructions 1 Work area a Keep work area clean and well lit Cluttered and dark areas invite accidents b Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gasses or dust Power tools create sparks which may ignite the dust or fumes c Keep children and bystanders away while operating a power tool Distractions can cause you to lose control 2 Electrical safety a Power tool plugs must match the outlet Never modify the plug in any way Do not 4 AFTER SALES SUPPORT 0203 5142281 1800 719901 www servotool eu WOC 1013 gt 2 070 KA Ng 777 use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock b Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded c Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock d Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for o
17. utdoor use reduces the risk of electric shock f If operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock 3 Personal safety a Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of carelessness while operating power tools may result in serious personal injury b Use safety equipment Always wear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce the risk of personal injuries c Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents d Remove any adjusting key or wrench before turning the power tool on A wrench ora key left attached to a rotating part of the power tool may result in personal injury e Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations f Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts g Use clamps ora vi
18. with water If liquid contacts eyes additionally seek medical help Liquid ejected from the battery may cause irritations or burns 6 Service a Please use a qualified expert who uses original replacement parts to repair your power tool b Caution The use of any accessories or additional tools other than those recommended in this manual may lead to an increased risk of injury and may invalidate your warranty Only use original replacement parts AFTER SALES SUPPORT 0203 5142281 1800 719901 www servotool eu WOC 1013 gt 2 070 KA Ng 7 Additional safety instructions lt Compare the maximum number of revolutions allowed of the accessories with the number of revolutions of the machine lt When you put the machine away the engine must be switched off and moving parts must have reached a standstill lt Never attach an assembly spanner to your machine with a piece of string or anything similar lt Donot use sandpaper intended for larger sanding pads Larger sandpaper will extend beyond the sanding pad causing snagging tearing of the paper or kick back Extra paper extending beyond the sanding pad can also cause serious lacerations lt Useaclamping device for securing the work piece lt Keep your hands away from the work piece lt Only use the accumulator block with the battery charger provided using other chargers could be dangerous lt Keep the accumulator block tool and battery charger
Download Pdf Manuals
Related Search