rockymounts flytrap adapter - rocky mounts 20mm thru
Contents
1. ROcKYMOUNTS FlyTrap Adapter Instructions Application and use The FlyTrap Adapter is designed to carry your 20mm thru axle except Marzocchi QR20 equipped bike on a fork mount We have tested and approved this for use with the following RockyMounts Clutch Lariat Noose Thule VeloVise V2 Echelon amp Peloton Yakima Copperhead Steelhead Viper amp Sprocket Rocket If your fork mount is not listed it is the user s responsibility to deem their fork mount sufficient At printing we offer an axle for use with the Specialized Enduro Forks sold separately as well Use of this product in other capacities or with a non specified fork will void the warranty DO NOT use bike covers or bike bras these items create excessive wind force If you do take the vehicle off road drive cautiously Bottoming out the vehicle suspension can be bad for both your suspension fork and the rack Approved for use with Single Bikes not Tandems Note on security Even the best locks are only deterrents to well equipped thieves RockyMounts cannot be held liable for stolen bicycles For additional security a cable lock can be run through the bike frame and roof rack or tie down Installation of FlyTrap Adapter In most instances the FlyTrap Adapter can be installed without removing the quick release from the rack Slide the large keyhole opening over the non handle side of the quick release Figure 1 Rotate the U shaped end onto the other side while p2. ing of Lock Core The bolt that secures the handle to the FlyTrap is factory set at 4Nm 3Lb Ft and should be periodically checked If the handle is too loose your bike can fall out To tighten the handle open the lid of the FlyTrap and insert a 10mm open end wrench onto the hex nut turn the bolt with a 5mm allen wrench while holding the nut The handle can also be replaced and is available as a Spare part at rockymounts com If you want to change the lock core only RockyMounts Lock Cores will work Thule and Yakima locks will not follow these steps Unbolt the handle from the body using a 5mm allen wrench and a 10mm open end wrench On the back side of the lock there is a small gold tab that is spring loaded Push this down with a small screwdriver and push the lock out A new Lock Core can now be installed With the key in the lock core align the thin protruding tab with the two arrows on the inside face of the handle Push in until flush Core is now installed Figure 1 Figure 2 Pull Up Key Push Down Hole Side gt x Open End Figure 3 Figure 4 F x F i H i j 7 tra y d CLOSED f a One Year Limited Warranty Rocky Mounts Inc Warrants to the original purchaser that the product will be free from defects in material and or workmanship for one 1 year from the date of original retail purchase Subject to the limitations stated below Rocky Mounts will at its own expense during the one year warranty period
3. repair or replace the defective component s The purchaser will be responsible for freight charges to Rocky Mounts This warranty is only applicable if the instructions are correctly followed and the components are properly used This warranty is not applicable if the defect is caused by normal wear and tear or exposure the component s is damaged from misuse abuse fire accident alteration mixing third party components with the system and or unlawful operation of the vehicle Rocky Mounts Inc cannot and does not assume responsibility for any damages to any property arising out of the improper attachment to a vehicle or a bicycle to the system or use of its products This limited warranty applies to Rocky Mounts products and not to the products used in conjunction with Rocky Mounts products This warranty is in lieu of all other warranties expressed or implied and does not cover consequential damages of any kind arising from the use or misuse or Rocky Mounts products ROCKY MOUNTS DOES NOT AUTHORIZE ANY PERSON TO ASSUME ON ITS BEHALF ANY OTHER OBLIGATION OR LIABILITY
4. ulling up on the keyhole side push down on the open end When it stops Figure 2 on the quick release close the skewer or mechanism per your rack manufacturer s instructions Be sure the FlyTrap adapter is level to the fork mount and properly engaged If it is crooked or uneven it will not hold properly Note Many thru axle forks are equipped on heavier downhill bikes These bikes put greater forces on the quick release It is imperative the quick release is closed properly Check the tension of the quick release EVERYTIME you mount your bicycle Some quick releases or mechanisms can lose tension over time in this case the FlyTrap Adapter can detach without the proper tension This is imperative for safe operation Use with a 20mm thru axle 1 Remove the axle from the front wheel and the front wheel from the fork Reinstall the axle in the fork as per your manufacturers specifications without the front wheel 2 Turn the black plastic handle of the FlyTrap open by turning clockwise until it stops and flip open the lid 3 Place your axle in the opening Figure 3 Flip the lid closed and turn the handle counter clockwise until it touches the built in stop on the bottom half Figure 4 4 You can now turn the key 90 degrees and lock the handle in place 5 Secure the rear wheel 6 Grab the fork and rock it side to side be sure the handle is closed all the way and the FlyTrap Adapter does not move on the fork mount Torque Setting and Chang
Download Pdf Manuals
Related Search