IP Camera User Manual
Contents
1. Consult the dealer or an experienced radio TV technician for help FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body 28 Your Security Our Priority SUPPORT SERVICES pa Lifetime Customer Support US based Tech Support 866 551 6881 24 7 Live Support on www zmodo com Mailing Address Champaign Office 1401 Interstate Drive Champaign IL 61822 Los Angeles Office 17870 Castleton Street Suite 200 Industry CA 917482. xxx xxx xxx xxx 80 FCC Statement 1 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation 2 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
3. Submit button the setting will take effect immediately Now pull out network cable you can access the IP network camera via Wifi Note WIFI setting only works to those types with WIFI function Wired network and wi fi network should not be set in the same network segment WIFI mode supported by IP Camera 802 11b g protocol small power WiFi type 802 11a b g n protocol large power WiFi type Listener Port LPRT Web Listening Port The default port 80 port 80 is recommended Video Listening Port default 8000 8000 is recommended Mobile phone Listening Port default 9000 9000 is recommendea After setting all parameters click the Submit button the setting will take effect immediately i Local Configuration Figure 4 8 LPRT setting Note LPRT can be selectable during range of 1024 65535 can t be repeated Web LPRT can be 80 PPPOE PPPOE Set to enable or disable the PPPOE dial up function User name The ADSL dial up account obtain from internet service provider Password Password of ADSL dial up account obtain from internet service provider After setting all parameters click the Submit button the setting will take effect immediately 11 Device Parameters p Local Configuration Figure 4 9 PPPOE Parameters Setting UPnP Auto Port Mapping UPnP If in LAN it has server with UPNP functionality enable this function the server will automatically forward the set port to public net
4. your external address EXTERNAL IP Ss a Nas E open port h EK Oh AA EI dee e Ahh ean ef gw LGecn e E en EP ze Coe e id Rp Dra d e 4 iii oa oe Arma sm EX TE RNA IS Aen SS A A date Ce So geg real pm poe a jp la e A af rem ama e A ez ban a IEI HH i es tl e p l ee ae E r si BR Pit ARAS pd A a hi rd TFU Emmis Ca de 9 Jr a bout a e at e e Gd Sg Of e mae j bes Bam mg erer a e fet pa A Va ee Saz eS paar ER y ra ee M s teal lo emailed a As ee a Bi oe poa ss wn ade eee gn A bia bead a er We hg ep o oe pa em 8 pe a eee i a m aiea Be gf BE em mo gin bhrag h ba Faura Ee Es Pal Kg as rn ja A egrbeg bas Ee E emm E p S gd LI peerd E sn o By P pt dir a TS ee HS pen A Pd geb F pm ss ir ee as ie k Bee ps eben b besse bg e ra ir E ege Ve Erwin Era rz t pre Bits S en ra Pm ts o Soe Faggi eet o Fee en Ee go gg VIEW AND CONTROL Sar ome rn FOR FAST _m 27 You will need to check each port for connectivity using this tool Enter 80 into the PORT NUMBER field then click CHECK You should receive the folling notation PORT80 is OPEN on XXX XXX XXX XXX Note The remote access that you see is your IPC external address This is the IP address you will see when you access your IPC via other different computers Please write this down If the port is open then you can visit remotely the IP camera via DDNS domain name at http jerry123 zapto org or http
5. varies Zoom focal length and Iris as figure 3 4 Figure 3 2 Image Parameter Figure 3 3 Color and Direction 3 4 PTZ Control Adjustment Control Figure System parameter setting Click this button LA to enter into system parameter setting interface Reboot device Click this button to reboot the device 4 System Setting Ig 4 1 Local Configuration Local Configuration Figure 4 1 Local Configuration 6 Video files packing time Set the video file packing time Video captured file storage directory Set file path for local recording and capture After configuration is finished click Submit button the configuration will take effect immediately 4 2 Remote configuration 4 2 1 Video Setting Character Overlay Title Name of video channel will be shown on the up left of the image maximum 16 characters Click the check box and it will display OSD Un check the check box and it will not display the title Time format You can choose whether to display title date and time and also you can choose the time format After setting the date and time click the Submit button the setting will take effect immediately Device Parameters Local Configuration Figure 4 2 Character Overlay Setting Video Coding Video quality The user can choose the appropriate desired image quality Best Very Good Good Common Low The type of stream Two types CBR Constant bit rate and VBR
6. video adjust their password and delete their own account Common users are not granted any additional authorities 17 Local Configuration Figure 4 19 User Management Interface Note The default user after leaving factory is admin the password is blank Both user names and passwords are case sensitive 4 2 6 2 Periodic Maintenance Local Configuration eras Y Maintaining 14 37 50 H F Mon Y Tues I Wed F Thurs Figure 4 20 Periodic Maintenance Setting Periodic maintaining Choose to open periodic maintenance and set maintenance time detailed maintenance time on everyday can be configured After setting all parameters click the Submit Restore factory setting Click this button to recover all the setting of the device back to factory setting 18 Reboot device Click this button to reboot the device Note Periodic maintenance and reboot the device will need to wait for 30 seconds to restore video surveillance 4 2 6 3 Software Update Device Parameters KEE Local Configuration User Management Regular Maintenance Software Update Update File C users Vacieniai Desktop 720p IPC 720P test V1 0 Ss _ update upgrade succeeded device is rebooting Figure 4 21 Software Update Update Click to browse for the correct update file application file IPC APP Please not change the file name click Update During the update it will display update information A
7. 168 0 100 User Name admin Password 111111 E A so Ge le mps A Biet Viewer DE Seres Weet Program Figure 2 2 Safety Dialog box IA CH LEI FE i Figure 2 3 Login Interface 3 Preview a hoan de ERA Y ERTAS E Sen BP Comers Web Manager Figure 3 1 Real time Preview Interface In the real time preview interface the user can control the video channel switch record snapshot full screen preview image process image color and direction configuration Video channel Double Click the channel number to open the video channel to view image right click and choose Close to close the video channel Video stream Right Click the channel number to choose stream type 720P VGA or QVGA Record Right click the image choose record check to start or Close local recording Capture Right click the image choose capture to capture photos Full screen preview Double click the image to full screen preview double click once again to go back to the Original image size Image process The object of image processing includes brightness ES contrast Saturation use mouse to drag the slider to set these items as figure 3 2 Color and direction configuration Image color can be black and white or color the image can be mirrored or reversed as figure 3 3 PTZ Control PTZ operations such as up down left and right and lens operations such as
8. IP Camera User Manual Your Security Our Priority For further help please visit www zmodo com Preface Dear customer thank you for choosing to purchase and use our IP camera products This series of IP monitoring product is the integrated IP network camera which is researched for network video surveillance monitoring The series includes network bullet camera network IR bullet camera and network dome camera etc High performance monolithic SOC chip is utilized as media processor which integrates video capture compress and transmission Standard H 264 main profile encoding algorithm ensures more clear and smooth video transmission Embedded web server allows user to view real time footage and remote control via IE browser This series of IP camera is well suited for home and small business as well as any situation which needs to apply remote network transmission and remote network control It s easy to install and operate Declaration e The content in this manual may be different from the product version you are using If you experience any issue that is not mentioned in this manual please contact our tech support or Zmodo Knowledge Base at kb zmodo com e The content will be updated time to time Our company reserves the right to update without notice Target Reader This manual is primarily intended for the following users e System planner e Onsite tech support and maintenance personnel e Administrator for system installati
9. NS system all you need to do is create an account here enter your login information into your ZMODO NVR with an internet connection and check the web site for a link straight to your NVR NEW FEATURE Download the new ZMODODNS standalone application for Windows You can now update your external IP address automatically from your Windows PC Un zip the folder anywhere and click on Zmododns exe Login to your Zmodo DNS account from there Zmodo DNS server updates your domain name automatically xxxx zmododns com Login to your Zmodo Check your DNS account on NVR from any a Windows PC Browser Pre Lem y s DO se nd Purchase Zmodo products here Choose your desired username and password at our site You will be informed if an existing user already exists or if your email is already registered limit 1 account per email 21 Signin Sign Out New User lt lt Enter a Username Password must be at Least 5 characters Email is necessary if you need to reset your password CREATE ACCOUNT 22 Signin Sign Out New User To use our DDNS system all Zmodo DNS you need to do is create an server updates account here enter your login your domain information into your Z2 MODO NVR with an internet connection and check the web site for a link straight to your NVRI Login to your Zmodo DNS account on h NEW FEATURE patil Download the new ZMODODNS stan
10. T FORWARDING RULES CONFIGURATION Remaining number of rules that can be created 44 T el roan e Te foe Deal e ACTIVE PORT FORWARDING RULES Name Address External Port Internal Port Protocol WANInterface Edi Remove 1 Enter the USERNAME and PASSWORD for your router when prompted If you are not sure what your router password is please locate your router onwww routerpasswords com If the default password provided bywww routerpasswords com does not successfully log you into your router please call your Internet Service Provider to find out your router s USERNAME and PASSWORD Click Advanced then Port Forwarding to enter the port forwarding section of the router 2 Fill in the port forwarding rules configuration Name IPC1 IP Address 192 168 0 100 External Port TCP 80 Internal Port TCP 80 External Port UDP 80 Internal Port UDP 80 Click Add Apply to create 26 you get emm E toons A Port Forwarding le ter gt a We mat hi li IN Al Haret a H RR kv E het work CHOI yl FE race Route ood gt i E Phone Number ec ator f eo Revere E mil LO YOU E Lis i a a ayere IP Doman Check gt f e WHOS Leen Titec gt gadgets G iGoogle Network Gadget gt Windows Vita Sdebar Gadget gt 3 To make sure your ports have been successfully opened navigate to www yougetsignal com From there click on Port Forwarding Tester Port Forwarding Tester E WE
11. Variable bit rate to choose CBR enables constant bit rate coding VBR enables variable bit rate coding Resolution Set the image resolution 720P 1280x720 921600 pixel VGA 640x480 307200 pixel and QVGA 320x240 76800 pixels Frame rate set coding frame rate per second Under not satisfying network situation you can reduce the frame rate to control the coding bit rate to ensure the smoothness and continuity of the moving footage After setting parameters click the Submit button the setting will take effect immediately Device Parameters Local Configuration Figure 4 3 Video Code Setting Video Block Video shield switch Enable or disable the video shield functionality Shield area setting User can set shield area by dragging mouse with left key pressed and cancel the shield box on the shield area by right clicking the mouse You can choose to shield the whole image or only shield the part of the image It can mask up to four areas You can right click the shield box to cancel this areas shield After setting parameters click the Submit button the setting will take effect immediately Device Parameters Local Configuration PA a 11 24 17 Figure 4 4 Video Shield Setting 4 2 2 Network Parameter Wired Setting DHCP If the router allows DHCP functionality select DHCP The IP Camera will obtain IP address automatically from the router If the router does not allow for DHCP fun
12. Wireless Network Connection After enabling the Wireless setting the software will automatically search for available Wireless networks The name of all wireless signals including signal intensity and the encryption will be listed on the screen Device Parameters Local Configuration DHCP M RER IP Addr 192 168 O SubnetMask 255 255 255 0 Gateway 192 ZE er 20 E MAC 7C 00 90 20 92 29 Figure 4 6 IPC WIFI Network Setting Click on add or double click on an existing network open WIFI Wireless Network Settings dialog box as the below figure shows Wireless Network P LINK C8FB9C Authentication Mode wea PSK Encrypted hal WEP Index WEP key 1 v Key Format fasci z EERE SES Password Figure 4 7 Wifi Hotspot Setting If the user entered this screen by double clicking a network will be assigned automatically If the user entered this screen by clicking Add the user has to type in network name choose a corresponding encryption mode and type in the password Click Connect then close the dialog box and the connection status will update on the search results list Connected will appear after network name if the connection was successfully established if not please click Refresh to refresh the connection status or re enter the Wireless Network Settings menu to re attempt to 10 connect to a wireless network After saving all parameters click the
13. ctionality then the IP address must be obtained manually IP address Set wired cable IP address of IP camera device Subnet mask Default 255 255 255 0 It is highly recommended not to change this setting Gateway Set gateway IP of IPC for example if IPC access public network through router the gateway IP need to be set as the router IP which has accessed the public network MACaddress MAC address of IP camera Read only cannot change DNS address If the user has a DDNS account the DNS address needs to be set as DNS address of the place where the device is belonging to After setting parameters click the Submit button the setting will take effect immediately Device Parameters Local Configuration E DHCP T IP Addr SubnetMask 255 255 255 Gateway 192 168 0 1 00 02 71 86 25 0D 02 9 HA 13 Figure 4 5 Wired Network Setting Note When the network parameter has been revised and saved the device will reboot If it is applied in LAN please make sure IP address does not conflict with the IP address of other devices or computer in the same LAN WIFI Setting WIFI Select this check to open the wifi network function of IPC DHCP If the router allows DHCP function select this type IP camera will obtain IP address automatically from router IP address Set wireless IP address of IP camera Gateway Set IP address of the current wireless gateway router AP such as 192 168 0 1
14. dalone application for Windows You can now update your external IP address automatically from your Windows PC Un zip the folder anywhere and click on Zmododns exe Login to your Zmodo DNS account from there DOWNLOAD Applicatio Purchase Zmodo products here CTV Ma Deals Once signed in you will need to add a domain This will be the address used to access your device Each account can request up to 5 domains for use with multiple devices at different IP addresses 23 Signin Sign Out New User Hi Demo These are your registered domain names with their current IP Max 5 EEEL Unassigned DMA EE 49 Unassigned DUES a New Zmodo DNS Functionality You may now type in your Zmododns name into any browser from any PC and access your Zmodo product newuser zmododns com Enter the desired domain name into the blank and hit submit If the name is available the user will be informed of a successful domain creation Otherwise the user will need to choose a different name Step 2 Configure the NVR to use zmododns The NVR must be actively connected to the internet prior to setting up dynamic DNS a In the NVR navigate to Configure system settings then Configure network settings then click on the DDNSSettings b Choose zmododns from the server drop down menu c Enter the newly registered user name into the Account field and the password into the passworo field d Enter the ful
15. et email parameter previously Sensitivity The sensitivity of motion detection includes three levels High Little high Medium and Low Output delay Set delay time of alarm linkage time range is limited between 0 30sec After setting all parameters click the Submit button the setting will take effect immediately 4 2 5 System Information Version Display device name system version video audio channel number sensor alarm input output local storage Time setting switch Enable this switch to manually set the system date and time disable this switch then the system date and time will be synchronized with local PC only to check the status and can t be configured to disable this switch After setting all parameters click the Sync time button the setting will take effect immediately 16 Device Parameters yo Local Configuration 00 02 71 86 25 C0 V 1 0 01 lv 1 0 02 System in Advanced Settings Device Parameters x Local Configuration Date 2012 10 17 v Time ced oe Figure 4 18 System Time Setting 4 2 6 Advanced Setting 4 2 6 1 User Management Each IP camera can be set up to have up to 15 users Admin is the system default super user and cannot be deleted but the admin password can be changed User s authority is as following Super User authority operate and set all the function and parameter of IP camera Common user authority The common user is allowed to view
16. fter update finished IP Camera will reboot automatically Log into the device once again and enter the software update interface to check whether the system version has been updated Note During updating please do not disconnect the camera from its power source or from the internet connection 19 5 Appendix la Appendix 1 Specification 10 50 C 20 80 Noncondensing Video Compression CBR VBR CBR VBR Resolution 1 30fps Selectable for main stream and 1 30fps Selectable for main stream and sub Frame rate sub stream stream Sub video code 640x480 320x240 320x240 Parameters Appendix 2 System Default Parameter IP address 192 168 0100 Gateway 192 108 0 IP address 192 168 0 101 Gateway 192 168 0 1 Mobile phoneLPRT 9000 20 NVR DDNS Brief Introduction DDNS dynamic DNS means real time analysis to a fixed domain and dynamic public network IP address of IP camera All internet users can visit this IP camera through a certain fixed domain that they have setup through our free DDNS service located at zmododns com Appendix 3 Port Forwarding Applying for a Free DDNS Domain Service For a complete interactive guide that details how to setup your NVR to be accessible from outside internet networks please go to www zmodo com network Step 1 Sign up for an account and create domain name for use with your device a Sign up for an account at zmododns com Signin Sign Out New User To use our DD
17. ftware leie E 19 A O A A eaa eere reene 20 APPENDIX 1 SPECIFICATION cuca ri A A dc 20 APPENDIX 2 SYSTEM DEFAULT PARAMETERS cooocccccccccccnnnnocccnnnnnnnnnnnnncnnnnnnnnnononannccnnnnonnnnannnnnnnnnnnnnnnns 20 APPENDIX 3 APPLCIATION FOR DDNS DOMAIN SERVICE o oooooccccccnccnncncooocccnnnccnnnonononccnnnnononannncnnnnnnos 21 O FCC STATEMENT amater ai E EEE EAE EE EEEE EEEE EEN 28 1 Product Introduction Ig 1 1 Brief Introduction This product is digitally monitored with a traditional analog camera and web video service Efficient Linux system code in flash and small size that s reliable and steady Power Gg 4 CY Power A iS Network Reset Reset Network Figure 1 1 Network IP Camera and Its Cable Ports 1 2 Main Features The highest pixels for100 W 4M frame rate real time image Supports up to Max three video streams One 720P One VGA One QVGA Advanced video compression standard high compression rate and flexible operation 720P IP camera applies 1 3 CMOS sensor VGA IP camera applies 1 4 CMOS sensor fluid motion pics Automatic snapshot in all circumstance One key rescue system network parameter modification and mobile phone live monitor Build in WEB browser supports IE access Support multiple user simultaneously multi level management ensures high system security Support motion detection alarm area sensitivity configurable and e mail alert function Support online system upgrade by re
18. l registered domain name into the domain field for this example it would be mydvr zmododns com e Be sure the On button is checked on the top left f Click Save to save the settings 24 Step 3 Access device via domain name or zmododns com The user may access his her device directly via the domain registered i e http zmodoexample zmododns com Zmododns com will also have the latest updated public IP address for each of the domains on the user s account The log in interface is easy and intuitive and will remember the user s session no need to log in again on subsequent visits Once logged in the user will be presented with links to his her domains Adjust the IP address of device the IP address needs to be LAN IP of the router which means the network segment when you enter into the internet in ordinary time Device Paramcters x Wired Settings wireless Settings Listening Port PPPOE UPNE Port automatically maps Emal FTP oons DHCP 7 IP Addr Subnet Mask Network Paran Gateway 192 a mac ng Alara Settings Preferred ONS Addr 202 e 96 D e 133 Alternate DNS Addr Advanced Settings 25 Step 4 Port mapping setting of D Link router Type in the IP address of router in browser to log in the main interface of router management Apobca tor Fides Check Se Aere i kii of pi Thee a fe abiiy lo apen ports m your router and ro et data Proch Pose pora to ange PE on your nebeori POR
19. mote control Automatic recovery function when the system temporarily loses internet connection Support PPPOE DDNS LAN and Internet ADSL Cable Modem 1 3 Installation Statement During installation and operation please pay attention to the following items 1 When you received the package product please check the equipment and accessories according to the packing list inside the packing case 2 Before installation please carefully read this user manual 3 When you install the IP camera please close the power source of all the related devices 4 Check the voltage of the power source to prevent device damage by mismatching of voltage 5 Installation environment please do not use equipment under high humidity or temperature Make sure there is good ventilation Do not install it in an environment that experiences frequent vibration 1 4 Network IP Camera Connection el IPC wireless 192 168 0 101 a IPC wired 192 166 0 1 192 168 0 100 Router Switch Hub Figure 1 4 Device Connection of Network IP Camera Step one Connect the IP Camera to internet through network cable Step two Connect the power adaptor in the package to the power plug of the IP camera and access into electric supply Step three Open the PC connect with the front end network IP camera to configure via software Note It can also apply the way of IP Camera directly connecting with PC Note When using IE browser to visit IP Camera the IP
20. of local PC should be in the same network segment with the IP of the IPC 2 Log in Fi When using IE Internet Explorer to visit IP camera for the first time you have to set the security level for ActiveX controls Set security level Open Internet Explorer enter the IE Tools menu Tools Internet Options Security Settings Custom Level set Active X Controls and Plugins to enable or Prompt and set the IP address of the IP Camera as Trusted sites A Security Settings Internet Zone 4 Download unsigned ActiveX controls A O Disable recommended Enable not secure Prompt Z 4 Intialize and script Activex controls not marked as safe for su j i co 1 e Browsing history Fronpt El Delete temporary Bez history cookies saved pasreords 7 Delete browsing history on et Ce Enable i 4 Run Actives controls and plug ins Delete Settings O Administrator approved Disable Enable lt gt R Reset custom settings ETT 3 Appesrance een Figure 2 1 Security Level Setting Install ActiveX and plugins Type the network camera IP address in the IE browser address bar and press Enter to pop out dialog box of install ActiveX Click OK to install Log in and Preview In Login screen type in network camera username password choosing language and click OK to enter the video preview interface Default IP Address 192
21. on e Users for business operation Terms in this manual IP Camera or IPC in this manual means network camera including network bullet camera network dome camera network PT camera and network IR camera etc e Click Refers to left click with your mouse e Double click Refers to left double click with your mouse e Right Click Refers to right click with your mouse e Square brackets indicates the window name menu name and data sheet such as Download 1 PRODUCT INTRODUCTION eegene 2 Ti BRIEF INTRODUCTION casi iia 2 12 IMANES KE 2 1 3 INSTALLATION STATEMENT scicivi niican ii iii ic iia 2 1 4 NETWORK IP CAMERA CONNECTION coooccccccccccccnncononccnnnnnnnnnconnnnnnnnncnnnnonnnnnnnnnnnanrrnncnnnnannrnnnnnanannnns 3 2 EOGAIN e a A II PA A E 3 3 TEE 5 A EM SETHNG cra ai a E E A 6 4 1 LOCAL CONFIGURATION ME 6 4 2 REMOTE CONFIGURATION ME 7 42 We Ee EE 7 Video Coding cnica 7 VideO BIOCK EE 8 4 2 2 Network Parametros A A AA AN 9 A ne teu ne dads senianeacandeatebaospouusniamsncade 9 A A OE UA A 9 Listener Port LPRT serte asta 11 o on PP 11 UPnP Auto Port Mapping EE 12 ut RE 13 A A A NA A A A A EE E A 13 Dee 14 42 3 lo slo Seling OM oo e o o O A 15 YOM VIdeo LOOD nn E EEE E E O 15 4 2 3 2 Video PINS AAA A EREE EEEE EEE Ei 15 4 2 4 Alarm setting E 16 4 2 5 A A O O PO A A vas 16 4 2 6 Advanced Setting nous tere tinas taenes 17 4 2 6 1 User Management EE 17 4 2 6 2 Periodic Maintenance eric ida ti n 18 4 2 6 3 So
22. red recording and motion triggered recording 15 Week Time You can choose one day from Monday to Sunday or choose everyday in the week also there is a time period for you to choose You need to click the time check to enable the time selection After setting all parameters click the Submit button the setting will take effect immediately 4 2 4 Alarm Setting Local Configuration ME EX T Port 1 Video Settings NA A _ Port 3 H wl Al t J I Audio W Capture 720P 161 17 43 3 T FTP Email M Record IV Upload Sensitivity Medium D Output Delay fo DI IV Motion Detect Figure 4 16 Motion Detection Setting Time Set the protection time of motion detection It can set detail time period of everyday up to four time periods Motion detection Set open or close of motion detection enable this switch to edit the motion detection area Motion detection area setting After enable motion detection switch the setting interface will appear grid line User only needs to click the little cube on the image to set the motion detection area Right click the little cube to cancel related area detection Alarm Method Set linkage output format after triggered alarm Four methods for you to choose Capture record email and upload Sending email is sending motion detection alarm information via email to user the detailed Email parameter see chapter 4 2 2 There will be no Email alert if user didn t s
23. the setting will take effect immediately Common email server configurations Hotmail server SMTP Server smtp live com SMTP User username hotmail com SMTP Port 25 SSL Enabled Yahoo Email server SMTP Server smtp mail yahoo com SMTP User name username yahoo com orusername yahoo com cn SMTP Port 465 SSL Enabled FIR FTP services will send the alarm triggered recording file or captured photo via FTP to certain FTP server 13 FTP server IP address or HTTP network address of FTP server FTP port Port of FTP server default port is 21 User User name of the FTP Server Password Password of the FTP Server After setting all parameters click the Submit button the setting will take effect immediately T_T Figure 4 12 FTP parameters setting DDNS Figure 4 13 DDNS parameter setting Note It is only necessary to setup DDNS settings on your NVR please refer to Part 1 section 2 3 3 4 of this manual for NVR DDNS setup and configuration 14 4 2 3 Video Setting 4 2 3 1 Video Loop Device P ter Local Configuration Cen Configuration Figure 4 14 Video Loop Setting Loop Video Click loop video when the storage of SD card is full system will overwrite automatically to continue recording 4 2 3 2 Video Plans evice Pa ter Local Configuration Figure 4 15 Record Type and Record Time Setting Type Three types of recording types to choose Schedule recording Alarm trigge
24. work Web mapping port Set the web port which will be mapping to the server Video mapping port Set the digital video port which will be mapping to the server Mobile phone mapping port Set the mobile phone port which will be mapping to the server After setting all parameters click the Submit button the setting will take effect immediately Device Parameters Local Configuration Figure 4 10 UPnP Port Mapping Setting 12 Note Port mapping can be selectable between 1024 65535 It can t be repeated Email r A i 7 Device Parameters eS Local Configuration Wired Settings Wireless Settings Listening Port PPPOE UPNP Port automatically maps Emal Je oons SS SMTP Server smtp gmail com Receive E mail Address zmodouser eptco com Send E mail Address zmodouser eptco com SMTP Password sssesees E mail Title alarm message SMTP Port SSL Figure 4 11 Email parameters setting This menu is used to set Email address and related parameter of alarm email SMTP server send email server address such as SMTP server of Google email box smtp gmail com Receive Email address Email address to receive the email Send Email address Email address to send email SMTP password Log in password for the email box Email title The title of sending email SMTP port Port of SMTP Server such as Gmail email server port as 465 SSL enabled After setting all parameters click the submit button
Download Pdf Manuals
Related Search