BH8-CTRLZ DS_eng - smart
Contents
1. BH8 CTRLZ BH8 CTRLZG smart house Controller Power supply AC Types Rated operational voltage through term 21 amp 24 jumper term 22 amp 23 Power on term 21 amp 23 Neutral on term 22 amp 24 Frequency Rated operational power Power dissipation BH8 CTRLZ BH8 CTRLZG Rated impulse withstand voltage 230V 115V Dielectric voltage Supply smart house Supply Output Supply Input Supply Com ports Heat dissipation it smart house T Fs BFs Al B A V V Supply ie smart howse SUPPLY SPECIFICATIONS Overvoltage cat III IEC 60664 230 VAC 15 IEC 60038 115 VAC 15 IEC 60038 45 to 65 Hz Typ 7 VA 3 W lt 6W lt 7W 4 kV 2 5 kV gt 4 kVAC rms gt 4 kVAC rms gt 4 kVAC rms gt 4 kVAC rms 4 W Power supply Rated operational voltage through term 21 amp 22 DC supply terminal 24 and 25 Reverse polarity protection Rated operational power Power dissipation BH8 CTRLZ BH8 CTRLZG Inrush current Rated impulse withstand volt Dielectric voltage Supply smart house Supply Output WIRING DIAGRAM 6 30 VDC y RS 485 Out Radio Contr Clock smart house Supply 10 30 VDC V S in V 10 265 VDC AC monit input BH8 CTRLZ 230 0 1 A 30 V CH 12VA Inputs DC Types Overvoltage cat III IEC 60664 10 to 30 VDC 50 Hz for synchronizing the clock in case of voltage break AC the log will automa2. ging e The smart house controller can be programmed to send out event based SMS messages The event can be a channel switching ON or OFF or it can be an analog signal crossing a set point e Requests for status of digital or analog data can be sent and answered via SMS messages e Status of digital channels can be controlled by sending commands via SMS messages In order to make use of the GSM modem the following is required e A SIM card with the pin code 9090 needs to be inserted into the slot in the front of BH8 CTRLZG xxx The SIM card must be a 3V type Specifications are subject to change without notice 12 09 2007 A product of the CARLO GAVAZZI Group BH8 CTRLZ BH8 CTRLZG smart house Controller e A GSM antenna needs to be connected to the FME connector on BH8 CTRLZG xxx If the unit is installed in a metal enclosure the antenna must be installed out side the enclosure and connected to the smart house controller via a cable an antenna of this type is available as accessory A LED in the front of BH8 CTR LZG xxx indicates the status of the GSM modem By emitting dif ferent blink patterns the LED indi cates connecting SIM card missing No network found No response from modem SMS sent and SMS received Radio Controlled Clock Option It is possible to equip the BH8 CTRLZx xxx with an external antenna for radio controlled clock in order to achieve high timing accuracy in connect
3. ion with real time functions and event time stamps When the antenna ANT2 oo smart hwowse MODE OF OPERATION cont is used the BH8 CTRLZx xxx will receive accurate timing signals from the DCF77 transmitter locat ed in Frankfurt a M Germany The antenna outputs the demodu lated signals to the smart house controller via an open collector driver The DCF77 transmitter covers all of Central Europe since the trans mission radius is at least 1000 km For longer distance the use of ANT2 depends on receiver condi tions ANT2 connects to the BH8 CTRLZx xxx terminals RS232 ports The smart house controller is pro vided with two RS232 ports COM1 and COM2 which both can be used by PC s PLC s for read write of smart house data using the Modbus RTU protocol COM1 is also used for download and upload of configuration files created by the smart house con troller configuration software and for firmware upgrades COM1 has a fixed baudrate of 115 kBaud while the baudrate of COM2 is adjustable RS485 port The RS485 port enables network ing of up to 32 smart house con trollers operating as Modbus RTU slaves This makes it possible for a PC or PLC operating as RS485 Modbus RTU Master to read write data from any of the 32 smart house controllers Each unit must be assigned a device address via the configuration software In total the RS485 network makes up to 4096 smart house I O points accessible from the PC
4. nect to pin 31 Pin 30 Piro Pin 32 Pin 33 Modbus RTU smart house carrier 8 2 V lt 130 mA Yes Sequence time 32 channels 128 channels Digital outputs Function Output voltage VDD Output current Output voltage drop Off state leakage current Short circuit protection Built in protective diodes Dielectric voltage Output smart house Output Input Inductive loads Inputs Digital Voltage Current Dielectric voltage Input smart house GSM Modem Siemens cellular engine Dual Band Output power Antenna connector GENERAL SPECIFICATIONS Better than 1 minute month Typ 48 hours lt 2 55 LED green LED yellow LED red LED red LED red LED red IP 20 Pollution degree Operating temperature Storage temperature Humidity non condensing Mechanical resistance Shock Vibration Housing Weight 38 6 ms 132 3 ms 4 PNP transistors Programmable lt 35 VDC lt 100 mA lt 2V lt 100 pA None None gt 4 kVAC rms 200 V External noise suppression required 6 30 VDC ON gt 5 5V OFF lt 1 5 V lt 6 mA gt 4 kVAC TC35 EGSM900 and GSM1800 Class 4 2 W EGSM900 Class 1 1 W GSM1800 FME 3 IEC 60664 0 to 50 C 32 to 122 F 20 to 85 C 4 to 185 F 20 to 80 RH 15 G 11 ms 2 G 6 to 55 Hz H8 housing 640 g Specifications are subject to change without notice 12 09 2007 A product of the CARLO GAVAZZI Group
5. or PLC Find below a RS485 networking diagram Modbus RTU protocol Using the Modbus RTU commands 2 and 3 through COM1 COM2 or RS485 makes it possible to read any type of smart house data digital analink or multiplexed analog The status of digital and multiplexed analog data can be controlled via the commands 5 6 and 16 See man ual for memory map information On board I O The smart house controller has 4 digital inputs and 4 digital outputs on board These have been imple mented to reduce the cost of remote stations with only a few signals e g in connection with an SMS alarm system or radio modem remote stations The onboard I O s are used via the logic functions of the smart house controller where they can be assigned to specific channel addresses PIN ASSIGNMENT COMT COM2 RS 232 CABLE 9 pin male 9 pin female to controller to PC TxD RxD Signal Ground 9 pin male 15 pin female to controller to radio modem NETWORKING smart house 1 Tart het iT oe eo EN on I O modules e Digital e Analogue I O modules e Digital e Analogue Modbus RS485 p gt gt i mn la X s on r Specifications are subject to change without notice 12 09 2007 A product of the CARLO GAVAZZI Group BH8 CTRLZ BH8 CTRLZG smart house Controller u smart hous DIMENSIONS TYPE SELECTION Supply Ordering no Ordering no H8 housing w GSM tele
6. phone 115 230 VAC BH8 CTRLZ 230 BH8 CTRLZG 230 10 30 VDC BH8 CTRLZ DC BH8 CTRLZG DC l R SCOPE OF SUPPLY 1 x smart house Controller BH8 CTRLZx xxx 73 ACCESSORIES GSM Antenna 900 MHz ANTI Antenna for radio controlled clock ANT2 1 x User manual _ 1 x RS 232 cable 0O0O0 HH0N0HONE 1 x Configuration software SW G 38xx15 MAN 15 029 223 RS 232 9 M 9 F Specifications are subject to change without notice 12 09 2007 A product of the CARLO GAVAZZI Group
7. smart house Controller BH8 CTRLZ BH8 CTRLZG Programmable smart house controller Option for built in GSM Modem for monitoring and control via SMS User friendly configuration via Windows 98 2000 NT XP software Real time timer and logic functions Analog set point control and monitoring Light and Rollerblind control functions Alarm Monitoring Option for Radio controlled clock for high real time accuracy 2 x RS232 ports for configuration and smart house data read write 1 x RS485 port for networking of up to 32 smart house controllers Modbus RTU protocol 4 digital inputs 4 digital outputs on board H8 housing for DIN rail mounting EN50022 AC or DC power supply Serial Port COM 1 COM 2 Data format COM 1 COM 2 Pin assignment Dielectric voltage Com port smart house Protocol RS 485 Protocol smart house Output Output voltage Current Short circuit protection Real time clock Accuracy Internal back up time Power ON delay Indication for Supply ON ON Line COM 1 COM 2 RS 485 GSM Environment Degree of protection TxD RxD GND Termination Fs B Fs A B A GND V oo smart wowse INPUT OUTPUT SPECIFICATIONS RS 232 115 kBaud 9600 Baud adjustable 8 bit No parity 1 stop bit 9 pole female SUB D Pin 2 Pin 3 Pin 5 gt 2 kVAC rms Modbus RTU Pin 27 When in use connect to pin 31 Pin 28 When in use connect to pin 30 Pin 29 When in use con
8. tically update itself until 10 mSec before loss of current Yes 6 W lt 6 W lt 7 W TA 800 V 500 V 200 V BH8 CTRLZ DC ee T Fs B Fs Al B A V RS 485 Out Radio Contr Clock Intelligent functions The BH8 CTRLZx xxx smart house controller is a program mable device which is particular ly well suited for building automation applications due to the dedicated intelligent functions for lighting control roller blind control temperature control and alarm monitoring In addition to that the unit can be configured to perform real time logic and timer functions The Windows based configuration software is extreme ly easy to use due to the pre pro grammed functions MODE OF OPERATION smart house controller configuration The smart house controller must be configured by means of the user friendly Windows based configuration software This is included in the package and has to be installed on a Win 95 98 2000 NT XP PC When the configuration is completed the configuration is downloaded into the smart house controller via COM1 RS232 port The configu ration can be saved on a file and it is also possible to upload the configuration from a smart house controller GSM Modem Option The BH8 CTRLZG xxx smart house controller has a built in GSM Modem which enables monitoring and control of smart house signals via SMS messages to from mobile GSM telephones There are 3 different ways to use SMS messa
Download Pdf Manuals
Related Search