User Manual
Contents
1. load mass above Il threshold Notice If a user erroneously enters a value of the lower threshold higher than the upper one the scale will indicate an error message and will return to weighing Return to weighing Es key twice e Press the 16 5 Control of deviation referring to the inscribed standard mass scale software enables control of deviation in of weighed loads mass referring to the inscribed standard mass Mass of standard can be determined by its weighing PrcA function or entered to the scale memory by an user PrcB function 40 16 5 1 Standard mass determined by its weighing Procedure e Enter to lt PrcA gt function bi 4 blinking pictogram e place an load on the pan which mass will be accepted as standard e press to confirm this operating mode e after few seconds the indication 100 00 will be displayed e From this moment display will not indicate mass of weighed load but deviation of load mass placed on the pan referring to the mass of standard in 9o Return to weighing e Press the Le key twice 44 16 5 2 Mass of standard inscribed to scale memory Procedure e Enter to lt PrcB gt function e Using C anc e set standard mass where e digit selection e digit setting e Confirm the entered value by pressing L e You will see the indication equal to 0 000955 e From this moment dis2. Scale type Max capacity Readability Range of tare Repeatability Linearity Stabilization time Pan size Operation temperature Supply Supplied from batteries Display WLC 1 A2 WLC WLC 2 A2 6 A2 WLC 10 A2 WLC 20 A2 0 01g 0 19 20kg 0 03g WLC 6 WLC 12 WLC 30 WLC 60 WLC 120 IC1 R IC1 R IC1 R IC2 R IC2 R WLC 6 WLC12 WLC 30 WLC60 WLC 120 IC1 K IC1 K IC1 K IC2 K IC2 K Com rse 714 1 o9 oo 400 x 500mm LCD with backlight 23 2 Verified precise scales of WLC series 0 6 B1 1 2 B1 1 2 3 A2 3 6 A2 6 12 A2 AC and 6xAA NiMH internal accumulator 6V Average operation when supplied from batteries 35h Display LCD with backlight WLC 6 12 WLC 12 30 WLC 30 60 WLC 60 120 Scale type WLC 6 12 WLC 12 30 WLC 30 60 WLC 60 120 Supplied from batteries Average operation when supplied from batteries 45h us 23 3 Precise scales of WLC C 2 series Scale type WLC 1 A2 C 2 Max capacity Readability Range of tare Repeatability Linearity Stabilization time 23 4 Verified precise scales of WLC C 2 series 0 6 A1 C 2 1 2 A2 C 2 3 A2 C 2 6 A2 C 2 73 24 ADDITIONAL EQUIPMENT P0136 KAFKA printer cable for PUE C 31 indicators P0151 EPSON printer cable P0108 Computer cable 74
3. command comprehended but cannot be executed CO ACRLF command comprehended and executed 66 20 4 9 Switch on continuous transmission in current unit oyntax CU1 CR LF Possible answers CU1 I CR LF command comprehended but cannot be executed CU1 ACRLF command comprehended and in progress MASS FRAME mass value in current unit is returned Frame format PPP PPP 20 4 10 Switch off continuous transmission in current unit syntax CUO CR LF Possible answers CUO I CRLF command comprehended but cannot be executed CUO ACRLF command comprehended and executed 20 4 11 Send all implemented commands syntax PC CR LF Possible answers PC gt Z T S SI SU SUI C1 C0 CU1 CU0 PC command executed the indicator have sent all the implemented commands 67 20 5 Manual printouts automatic printouts Users can general manual or automatic printouts from the scale e Manual printouts can be performed after paang the pan and stabilizing indication by pressing Lee e Automatic printouts can be performed only after loading the pan and stabilizing indication Notice If a scale is verified printouts of immediate values are blocked Format frame Stability character space if stable if not stable if an indication over the range v if fan indication below the range sign space for positive values or for negative values mass 9 characters justified to the right unit 3 characters j
4. CR LF computer command SI 18 5 kg CRLF command done mass value in basic unit is returned immediately 20 4 5 Send the stable result in current unit oyntax SU CRLF Possible answers SU ACRLF command accepted and in progress SU E CRLF timeout while waiting for stable results SU I CRLF command comprehended but cannot be executed SU ACRLF command accepted and in progress MASS FRAME mass value in current unit is returned Frame format PPT le elle Example S U CR LF computer command SU _ ACR LF command accepted and in progress SU 172 135 N CRLF command done mass value in current unit is returned 20 4 6 Send the result immediately in current unit oyntax SUI CR LF Possible answers 65 SUI I CRLF command comprehended but cannot be executed SUI ACRLF command accepted and in progress MASS FRAME mass value in current unit is returned immediately Frame format PPP ee Pere Example SUI CR LF computer command SUI 58 237 kg CRLF command executed and mass returned 20 4 7 Switch on continuous transmission in basic unit syntax C1 CR LF Possible answers C1 I CRLF command comprehended but cannot be executed C1 ACRLF command comprehended and in progress MASS FRAME mass value in basic unit is returned Frame format qp ep Pel 20 4 8 Switch off continuous transmission in basic unit syntax CO CR LF Possible answers CO I CR LF
5. WLC B1 series or lt SLA gt for scales of WLC A2 WLC C 2 series e Incase of damaging accumulators or lack of it the pictogram blinks quickly period about 0 5 sec Notice WLC C1 C2 and WLC B1 scales are equipped with NIMH batteries packs R6 AA size and Power adapters for supplying from mines Procedure e Enter the submenu lt P5 othr gt and then CHr6 YES enabled CHr6 no disabled Return to weighing See 11 2 2 15 4 4 Formatting rechargeable battery packs WLC C1 C2 and WLC B1 scales are equipped with NiMH batteries packs R6 AA size and Power adapters for supplying from mines They need formatting after first powering up It is crucial for batteries lifetime to undertake this process Formatting consist in charging and total discharging without meantime charging 34 Procedure 1 Supply the indicator from mains Charge batteries for 12 hours time of charging 2200mAh batteries After 12 hours unplug from mains Use the device up to the moment of self powering down Repeat the process of charging starting from point 1 C1 AOUN Notice They reach their optima capacity after three cycles of full charging and discharging 16 OPERATION MODES 16 1 Setting accessibility of operation modes In this parameter group users can disable enable accessibility of functions after pressing sJ key Procedure e Enter the submenu lt P4 Func gt and then no mode is
6. all weighings will be printed 1 1 912 kg 2 1 912 kg TOTAL 3 824 kg e Incase of pressing one more time with loaded pan you will see the unLoAd message Unload the pan the scale will return to ZERO and the letter P in the left part of the display will appear The scale is ready for the next procedure e n case of pressing L one more time with loaded pan you will see the letter P in the left part of the display will appear The scale is ready for the next procedure 16 8 3 Memory of the last value of sum of weighed goods After interrupting e g switching off the totalizing procedure it is possible to restart the procedure without loosing data In order to do it just enter the totalizing procedure e Enter Add function again according to the ch 16 8 1 of the manual e You will see the last memorized sum of weighings on the display 46 In order to continue the procedure press _ _ the indication returns to ZERO and the letter P appears in the left part of the display The scale is ready for weighing In order to terminate the previous totalizing procedure press Ls G key e Or e You will see the letter P in the left part of the display The scale is ready for weighing 16 8 4 Return to weighing e Press Es key you will see e Before leaving the lt Add gt function it is possible to print out subsequent weighings and the sum of a on the connected p
7. disabled YES mode is enabled 399 Return to weighing See 11 2 2 16 2 Selecting quantity of operation modes E This function enables user to set if after pressing key all operating modes will be accessible ALL or only one from the list chosen and used by operator Procedure e Enter the submenu lt P4 Func gt and then tof e Pref After choosing setting press key The program will return to displaying name of submenu lt P4 1 FFun gt Return to weighing See 17 2 2 36 16 3 Counting pieces of the same mass otandard solution is equipped with option of counting small pieces of the same mass Counting pieces does not operate with other scale functions It is possible to execute a tare function in this operating mode in order to tare a container value Procedure e Enter to lt PcS gt function e You will see a blinking value of sample quantity ng event e Press _ _ key to start setting quantity of sample you have a few options to chose from FrEE e Ifthe lt FrEE gt option is selected you will see g e Using and enter the required sample quantity e where selection of digit position setting the digit e Confirm the value by pressing e You will see lt LoAd gt on the display and then Ou atn blinking pictogram e f weighing is performed in a container put the container on the pan first and then tare it Then put the declared
8. power adapters and NIMH rechargeable batteries standard equipment New rechargeable batteries should be formatted according to the description in the chapter 15 4 4 of this manual If you want to use normal batteries instead of rechargeable ones proceed as follows e Before installing non rechargeable batteries turn on the device and set lt 5 5 CHr6 gt to lt no gt to switch off charging e Then install the batteries Installing batteries without changing lt 5 5 CHr6 gt to lt no gt may cause damage of batteries and the indicator 3 WARRANTY CONDITIONS A RADWAG is obliged to repair or change those elements that appears to be faulty because of production and construction reason B Defining defects of unclear origin and outlining methods of elimination can be settled only in participation of a user and the manufacturer representatives C RADWAG does not take any responsibility connected with destructions or losses derives from non authorized or inappropriate not adequate to manuals production or service procedures 6 Warranty does not cover e Mechanical failures caused by inappropriate maintenance of the device or failures of thermal or chemical origin or caused by atmospheric discharge over voltage in mains or other random event e Inappropriate cleaning Loss of warranty appears after e Access by an unauthorized service e Intrusion into mechanical or electronic construction of unauthorized pe
9. tare value e Press e Program returns to weighings mode The inscribed tare value can be seen on the display with sign e are can be inscribed anytime in weighings mode Notice 1 You cannot inscribe a new tare value when the tare value in memory is greater than zero In the case of trying this the Err3 message will be displayed and short audible signal will be emitted 2 Users can also enter up to 9 tare values to the scale memory see 16 10 of his manual 12 3 Zeroing To ZERO the scale press e The scale will display zero and following pictograms and mua Zeroing is only possible within the scope of 2 of full scale While zeroing outside the scope of 2 you will see lt Err2 gt Zeroing is possible only in stable state Notice Zeroing is possible only within the 2 interval of the maximal range If zeroing is performed beyond this range the Err2 message and short audible signal will be emitted 12 4 Weighings in two ranges Switching between the I range and the Il range happens automatically exceeding Max of the I range Weighings in the second range is signalled by a pictogram in the top left corner of the display Then weighings is done with the accuracy of the Il range to the moment of returning to zero autozero range where the scale switches back to the range 18 12 5 Selection of basic weight unit This function is used to set weight unit the scale will start
10. with Procedure e Enter the submenu lt P3 Unit gt and then Options A When the basic unit is kg users can toggle between kg Ib N for verified scales Ib is not accessible B Ifthe basic unit is g users can toggle between g ct Ib for verified scales Ib is not accessible 19 e After you select the unit press L the scale returns to e Return to weighing according to chapter 11 2 2 Notice After turning on the scale always sets the basic unit 12 6 Temporarily selected unit This function is used to set weight unit the scale will use temporarily until the next power off or next selection Procedure e Press s and then kg e After you select the unit you want come back to weighing procedure 20 Options A When kg is a basic unit users can select following units kg Ib N Ib is not accessible for verified scales B When g is a basic unit users can select following units g ct Ib Ib is not accessible for verified scales 13 MAIN PARAMETERS Users can adjust the scale to external ambient conditions filtering level or particular needs autozero operation tare memory This parameters are placed in P1 rEAd submenu 13 1 Setting a filtering level Procedure e Enter the submenu lt P1 rEAd gt and then 1 4 level of filtering e By pressing select the filtering level you need T Notice Filtering
11. 16 10 1 Entering the tare value to the scale memory Procedure e Enter to lt tArE gt function 49 e he program goes to displaying the first value from the selection of tare values tArE 0 press C to chose different values eT ERHrE 0 LAFE i LArE 2 LArE 3 ERE 5 thre i e After selecting the right position press and you will see an editing field e Enter the selected tare value to the scale memory 9 50 e he program returns to the following window Return to weighing o e Press Lec 16 10 2 Selecting a tare value from the memory e Enter lt tArE gt function according to the ch 16 10 1 of the manual e he program goes to displaying the first value from the selection of tare values tArE 0 press e to chose different values bare B ERE l ER E 2 tAr EB E 3 BAPE 6_ ERrE 5 hire i e o use an entered tare value press Q you will see the tare value on the display preceded by the sign and the Net pictogram Caution A tare value from the memory is not remembered after powering off and on the scale 54 17 SCALE CALIBRATION In precise scales changes of gravitational acceleration have noticeable influence The gravitational acceleration changes with altitude and latitude Every scale has to be adjusted to the place of use especially when the place changes Frequent calibration also prevents weighing process from the influence of h
12. 7 Measurement of maximal force on the pan latch eeseeeeeeeesee 44 howe mel 2 4 NER RE 44 16 5 4 Enablndgd drie WOFK MOU osea Dua edebat ta dad tete marido dot unte ane Choo dE bot al oin 45 16 8 2 T lalizifig DIOGGOUEO oed atto eh och ema rota gerat ooa ua den a es eps Datis 45 16 8 3 Memory of the last value of sum of weighed goods 46 16 8 4 Return to Weighing as ecscic cuti secos cages eoa ete i rat has is te sad ded su aco uto o ud de euo ees 47 IE WIGAN ANIM el o5 ost tele Esa Cima uM ME NIA 48 sU Fai zuo RENT m T TT MET 49 16 10 1 Entering the tare value to the scale memory eseeeeseessess 49 16 10 2 Selecting a tare value from the MEMOLSY cccceccceececeeeeceeeeaeeeeaeeeeseeesaeees 51 17 SGALE CALIBRATION 2 375 vd Uds vox Dew eara eaa vasa dea en ovi celat diventa eager aatatafE cue s ue ENDE 52 i grid PN w ays Keil ge Ie PTT E ONERE 52 17 1 1 Manual internal calibration ccc cccccecc cece eeeseeeeeeseeeseeceeeseeeseeeeeeseeeeeeeenees 53 17 1 2 Automatic internal calibration cccccccccccececeeceeeceeeceeceeeceeeaseceeeseeseeeeeesaes 54 17 2 TEXTS Nall calibrato M essee Que ux eA e atout hens us KERNE EENE 57 Toc votalttiassadiustt Hei siet e a Socio S 58 18 COOPERATION WITH PRINTER ius ROREM ME NEEnV uS UuEER FER RE ERECE Y YEREE CENKER YER HER Rru NOE VES 60 19 CO
13. OPERATION WITH COMPUTER e cerileeenenene nennen nnne n enhn n nan nhan aaa 61 20 COMMUNICATION PROTOTQCOL 11 e e eeeeseeesieeneeen hen nnn hhn nanus ansa nua n nans a anas 62 20 1 General information ccccceccc cece eecceeeceseeeseeca cece ceseeeseeeesueeseesaeeeeeeseeeseeeeseeeseeeseess 62 20 2 A set of commands Tor RS Interfaces cte e E inet ice iss euin ieieeiovda 62 20 3 Respond message format ccccsecccseccceecccesecceeecaeeceueeceuceceueeseeesaeessueeseusesseeenags 63 20 4 COMMana S GESCHIDIOMN 454th ru deeincd se destsxdstnteka Ducis odo poto initiate a dA SL tine EA MUS 63 ZO As ZOTONING EE D T T T T 63 ZO EE giro eT RETRO RUP T ER 63 20 4 3 Send the stable result in basic unit eese 64 20 4 4 Send the result immediately in basic unit eeeeeseeeseeeeseeees 64 20 4 5 Send the stable result in current UNIt 0 cece cece cece ceeeeeeeseeeseeeeeeeeseeeneeees 65 20 4 6 Send the result immediately in current unit cccceeccceeeeceeeeseeeeeeeeeaeeeeaeees 65 20 4 7 Switch on continuous transmission in basic unit Leseseesssssss 66 20 4 8 Switch off continuous transmission in basic unit sssueesssesee 66 20 4 9 Switch on continuous transmission in current unit ssusuesesusee 67 20 4 10 Swit
14. again automatically after the result changes 15 1 2 Backlight for supplying from batteries The user can change the intensity of backlight from 0 to 100 The lower the intensity is the longer the scale operates without recharging or exchanging batteries When the intensity is set this function works as AUTO described above Procedure e Enter the submenu lt P5 othr gt and then Return to weighing See 11 2 2 Notice The more intense the backlight is the shorter the scale operates on batteries 15 2 Beep signal after pressing a key Procedure e Enter the submenu lt P5 othr gt and then bEEP no switched off bEEP YES switched on Return to weighing See 11 2 2 15 3 Automatic switch off This function is essential to save the battery power The scale is switched off automatically when function t1 2 YES no weighing appears in 5 minutes no changes on the display In case when this function disrupts the operation e g long time weighing procedures or while working with connection to mains switch off this function Operation according to the power supply Mais Batteries accumulator t1 0 disabled disabled HZ YES HI Auto disabled 31 automatic enabling disabling according to the source of power Procedure e Enter the submenu lt P5 othr gt and then Returnto weighing See 11 2 2 15 4 Battery voltage level check While supplying from batteries
15. all samples average value standard deviation variation factor min value max value difference max min Cable diagrams SCALE KAFKA printer DBBS F female connector Din 5 plug Signals from D 1 7 m Ind scale A pin M GND pin 5 s i TxD pin 3 RxD pin 2 Solder side view Solder side view Scale Kafka printer cable diagram 60 19 COOPERATION WITH COMPUTER oending weighing results to the computer can be done manually after pressing key in continuous way after function activating or sending an appropriate command automatically After stabilizing the indication on the request from the computer After sending a control command These scales can cooperate with EDYTOR WAG program The indicator window comprises the most important information from the scale display The program allows to configure easily e g design printouts edit parameters A precise description is issued in the Help file that accompanies the program Cable diagrams COMPUTER SCALE Female connector Female connector DB3S F DBS F BCIELD Signals from we XD 1 7 m awe 5 scale T Bile Ge IA A g sameton i ajo eds pre e 3 o arem pin3 TxD pin 2 RxD ea d vellow e pin5 GND pin3 TxD illo 6 r ee 7 1 pins GND Solder side view Solder side view Scale computer cable diagram 61 20 COMMUNICATION PROTOCOL 20 1 General information A A character protocol
16. ass beyond the acceptable range 1 for weight 10 for start mass Err5 Mass of a single piece lower than the scale division Err8 Exceeded the time for tarring zeroing start mass adjustment or span adjustment NULL Zero value from the AD converter FULL2 Measurement range overflow LH Start mass error the mass on the weighing platform is beyond the acceptable range 10 of start mass 5 FULL Display range overflow in totalizing Notice 1 Errors Err2 Err3 Err4 Err5 Err8 null that appear on the display are also signalled by a short beep sound about 1 sec 2 Error FULL2 that appears on the display is also signalled by a continuous sound until the cause of error disappears 22 TROUBLE SHOOTING Problem Cause Solution Discharged batteries Connect to eae Turning on does change batteries not work No batteries not installed Check the correctness of or improperly installed installation polarization The scale turns off t1 set to YES In othr submenu change automatically Power save 5 4 t1 to no After turning on LH Loaded weight pan during Unload pan Then the message on the display powering up scale will indication zero 70 23 TECHNICAL PARAMETERS 23 1 Precisions scales of WLC series Scale type Max capacity Readability Range of tare Repeatability Linearity otabilization time Pan size Operation temperature Supply Supplied from batteries Display
17. ch off continuous transmission in current unit 67 20 4 11 Send all implemented commands ccc cece ccc eeeceeeceeeeeececeseeceeeeeeeeeeeaeeaaes 67 20 5 Manual printouts automatic PriNtOUts ccc ceccceeceeeeeeeeeseeeeeeeeeeeeseeeaeeaeeeseeesaeess 68 20 5 Conl nuous transmis SOLE 45 553 aa aet ia ode ot ee Ae 69 ZO Grelerireis gislege visitor P 69 PAM SS sc a aO T 70 22 TROUBLE SHOOTING 51 5 crescit eva ta ngo SS FUR S e RERO x Rex MES n tra eU Cuna a 70 23 TECHNICAL PARAMETERS seciccccscvacessnazscessenacssncaeacannssacenscncsacssancenacssncanecantotenessuassanpaneces 71 23 1 Precisions scales of WLC series ice een abad cea t ate oiu Sa Uo eee aes ox ede ise c es edes 71 23 2 Verified precise scales Of WLC series c ccc cece eccceeceeeceeeeeeceeeseeeeeeseeseeeseeseeeaees 72 23 3 Precise scales Of WLC 0 2 Sefrles cu sci reet pag REI UV AT Ha Nr CR RUD VM S ERANR A 73 23 4 Verified precise scales of WLC C 2 series 0 cccccccccccceecceeeceeeceeeteeeceeeeeeeseeeseeess 73 24 ADDITIONAL EQUIPMENT ccc cccccceeeeeeeeeeeeeneceneeceeeeaeeeeesseaeseaeseaesaeseaesseeesenesenesons 74 1 INTENDET USE ocales are designed for fast and precise measurements of weighed loads masses and direct commercial settlements Tarring in full weighing range enables to determine net mass of weighed loads Additional display is a
18. command accepted and in progress Z CRLF command comprehended but zero range overflow appeared Z ACRLF command accepted and in progress Z ECRLF time limit for stable result exceeded Z I CRLF command comprehended but cannot be executed 20 4 2 Tarring oyntax T CRLF Possible answers T ACRLF command accepted and in progress T DCRLF command completed 263 T ACRLF command accepted and in progress T vCRLF command comprehended but tare range overflow appeared T ACRLF command accepted and in progress T ECRLF time limit for stable result exceeded T I CRLF command comprehended but cannot be executed 20 4 3 Send the stable result in basic unit oyntax S CR LF Possible answers S ACRLF command accepted and in progress S ECRLF time limit for stable result exceeded S I CR LF command comprehended but cannot be executed S ACRLF command accepted and in progress MASS FRAME mass value in basic unit is returned Frame format qe e e e e Eee ee Example S CR LF computer command S _ A CR LF command accepted and in progress S 8 5 g CRLF command done mass value in basic unit is returned 20 4 4 Send the result immediately in basic unit oyntax SI CR LF Possible answers SI I CRLF command comprehended but cannot be executed at the moment SI ACRLF command accepted and in progress MASS FRAME mass value in basic unit is returned 64 Frame format ee Example S
19. dditional equipment of scale Functions backlight of display level of filtration autozero function setting baud rate of transmission continuous data transmission for RS 232 automatic operation for RS 232 designed printouts designation minimum mass for function operating counting pieces mass control percentage deviation from standard mass latch of maximum scale indication automatic tare memory of tare inscribing tare value Memory of 9 tare values automatic scale switch off user calibration internal calibration Totalizing Weighing animals User functions may have attribute of accessibility For this reason it is possible to adjust scale to individual needs to provide access to only these functions which are currently needed Attribute determination accessible inaccessible is possible in user menu and described in further part of manual 2 PRECAUTIONS 2 1 Maintenance A Please read carefully this user manual before and use the device according to its intended use B Dead batteries accumulators should be utilized according to the law C Devices that are to be withdrawn from use age should be sent back to the producer or in case of own utilization do it according to the law In case of an elongated storage period in low temperatures it is not allowed the full discharge of the accompanied batteries 2 2 Power supply Weighing indicators in plastic casing and WLC B1 series can be supplied from
20. divisions e 10d where d reading division e verified division the last digit Will be marked as shown below 000 7 BALANCE LEVELLING e Operation temperature range for this device is outlined as 15 C 30 C e After powering up this device requires 30 minute worming up e During the worm up time the indication can change e User calibration should be performed after the warm up time e Temperature and humidity changes during operation can increase measurement errors which can be minimized by performing the user calibration process 8 KEYPAD DDBB gsoasgg BgsoBaBmBgBes Keypad of WLC A2 series Keypad of WLC C 2 series 11 n000 0 000 OK C2 BOO Keypad of WLC C1 C2 series Keypad of WLC B1 series Notice Scales of WLC A2 series are equipped with an additional key for tarring and has no additional functions but the keypad of the WLC C 2 scale include an additional key e for direct starting the process of internal calibration Because the functionality and operation of the rest of the keys is the same the further part of this manual describes the keypad of WLC C1 C2 series 9 KEYS FUNCTIONS owitching on off Function key operation mode selection sending a weighing result to RS232 Zeroing Cal Tarring Manual internal calibration WLC C 2 scales Notice After pressing keys functions changes The way of operation in this mode is desc
21. ds scale software will react with lt Err8 gt displayed and a short sound and then the calibration procedure will start again 56 17 2 External calibration Option only for non verified scales Not accessible in WLC C 2 scales of WLC series Procedure e Enter submenu lt P6 CAL gt and then e Following messages will be displayed nnm LI LI LI e During this time start mass is adjusted and after completing the procedure calibration weight mass is displayed e g 3 000kg e Place the required weight on the pan e Calibration process starts automatically after placing the adequate weight that is signalled by the following message n L a AN I L 57 e he completion of the calibration procedure is signalled by the following message e Take off the weight from the pan the message lt donE gt is displayed for 1s and the program returns to the calibration submenu Esc e Calibration process can be terminated anytime by pressing C which is signalled by the following message on the display flbore e Return to weighing with saving changes that have been made Caution If the calibration process span adjustment lasts longer than 15 the lt Err8 gt message will be displayed and short audible signal will be emitted Press Le to perform calibration again with more stable ambient conditions 17 3 Start mass adjustment Option only for n
22. e function on and is stored in balance memory after unplugging it from mains Description of function operating point 16 6 automatic tare tArA no automatic tare function off user can turn on operating of automatic tare F6 AtAr till unplugging the balance from mains tArA tArF tare memory function stores last value of tare in balance memory It is automatically displayed after starting the balance Value of tare is displayed with minus sign and there is Net symbol indicated on the display user can turn on operating of automatic tare F6 AtAr till unplugging the balance from mains Return to weighing See 11 2 2 24 14 RS 232 PARAMETERS External devices connected to RS 232C have to be supplied from the same mains and common electric shock protection It prevents from appearing a potential difference between zero leads of the two devices This notice does not apply to the devices that do not use zero leads Transmission parameters Baud rate 2400 38400 bit s Data bits 7 8 otop bits 1 2 Parity control no even odd There are four ways of sending data via RS232 interface Manually after pressing e e Automatically after stabilizing the indication over LO threshold e Continuously after it is activated in parameter or by a command sent via RS232 e On external request see List of scale computer commands The indication can be sent as e Stable the indica
23. eeceeeceececeeeceeeceesseesaueeaseenenenes 31 USES E FAULOIMaLIC SWING OM er 31 15 4 Battery voltage level check ioo ob opo bU RR EE EB Eun reed pe Does lone Diei en eu ae 32 15 4 1 Checking the batteries cccccccccsccsscecseecseeceeeseeeceeeceeeceeeseeesaeeseueseeesaeeenes 32 194 2 Battery discharge pictogram ssassn ee intei tte uk Eneas etae made 33 19 4 3 Accumulator charginig OPTION sessies erusin FU EO iE oe eu ted ua onte du os eoa der bones 33 15 4 4 Formatting rechargeable battery packs seeseeeeeeeeeeeeeeeeeeeee 34 T6 OPERATION MODES 5 2 ueeseRudic ane aA Co SR ERG Lac deu dE ch cec cunacqnecesseoseqeecence 35 16 1 Setting accessibility of operation modes eeseeeeseseseeeneeenen 35 16 2 Selecting quantity of operation modes sssessseesseeeneeenneneneee nnns 36 16 3 Counting pieces of the same mass 1 esses nennen nnn nnns 37 16 4 control referring to the inscribed standard mass seesesusse 39 16 5 Control of deviation referring to the inscribed standard mass 40 m 16 5 1 Standard mass determined by its WeIQNING ccceeccceececeeeeseeeeaeeeeeeeesaeees 41 16 5 2 Mass of standard inscribed to scale memory eeeeeeeeeeseesss 42 1602 eism 43 16
24. ent press the key Return to weighing e Press the Les 16 8 Totalizing ocale software is equipped in a totalizing function of single weighings The totalizing procedure can be documented on the printer connected to the indicator 44 16 8 1 Enabling the work mode Procedure e Enter to Add function e A letter P in the left side of the display is a confirmation that Add function have been selected 16 8 2 Totalizing procedure e Enter Add function according to ch 16 8 1 e Putthe first load on the pan If the weighing procedure is performed in a container put the container on the pan first and tare it Then put the first load on the pan and confirm it by pressing e when stable signalled by i a e You will see a sum of weighings on the display the A pictogram in the upper right corner will be displayed and the weighing result will be printed on the printer connected to the indicator 45 e Take off the load from the pan indication returns to ZERO and the letter P in the left part of the display appears e Putthe next load on the pan e After stabilizing press e the sum of first and second weighing will appear on the display the A pictogram in the upper right corner will be displayed and the second weighing result will be printed on the printer connected to the indicator 9 e Press to complete the procedure with the loaded or unloaded pan a sum of
25. es DNE Im dua 15 12 VGN Go Seid c a 16 UXPME Iob 17 12 2 InSctIDIDg tare Valls iesu ausos E edi cu eceodt dox aon cose Giri at deua taticweee 17 MZ ZS ON MERE NN NEUE T EM 18 ZA Weldningds In TWO FarideS c acc ett cite R dac tee eia po Na UE 18 12 5 Selection of basic weight unit sessssssssssssssssesseeeeneeennnen nnne nnns 19 12 0 Temporaly Selected Ub oso ita aeneo sta a etit rta abiit Pee aet de freed ele 20 13 MAIN PARAMETERYOS iiiueuiia ous eoseo is esri eec se ois e2h o Oo tuias dpa sro Foo seo eos scien ue Cat eoa nenna ennnen annman 21 19 1 Seting a Tilteblfidg IGVBL uus occu ccnvas absences ace eiae eR hd aiT 21 NDZ NIGGA NC ee e c Tn 22 19 9 AOZO THETCUOTIS ceret a been bisce Latest tup tc ee duci eed 23 1s TE UNCU OM c ES TM I EE 24 14 RS 292 PARAMETERS eiiis 15236 as ete ie aatis ea aaia 25 1 SM UOC UY OS 22 od tata c 25 DAZ Minimal mass Mre shold eiaa a N O 26 do M Baud fae ETC 2f 14 4 Serial transmission parameters sssessssssssssessseeeeee ene ene nnne 20 15 OTHER PARAMETERS Reece een ene ace er ee a eee uua ho a Du nuoc tee en iau 29 MO cE ACK IMO TMC EOIN ET mcn 29 15 1 1 Backlight for supplying from Mainsand 29 15 1 2 Backlight for supplying from batteries 2 0 0 0 cceecceeeeeeeeseeeseeeseeeseeeeeeeeseeens 30 15 2 Beep signal after pressing a Key ccccscccsecceecce
26. level influences the time of stabilization The higher the filtering level is the longer stabilization time is needed Return to weighing See 11 2 2 13 2 Median filter This filter eliminates short changes impulses of measure signal e g shocks Procedure e Enter the submenu lt P1 rEAd gt and then Fnnd no filter disabled Fnnd YES filter enabled Return to weighing See 11 2 2 27 a 13 3 Autozero function The autozero function has been implemented in order to assure precise indications This function controls and corrects 0 indication While the function is active it compares the results continuously with constant frequency If two sequentional results differ less than the declared value of autozero range so the scale will be automatically zeroed and the pictograms md and gt Q lt will be displayed When AUTOZERO is disabled zero is not corrected automatically However in particular cases this function can disrupt the measurement process e g slow pouring of liquid or powder on the weighing pan In this case it is advisable to disable the autozero function Procedure e Enter the submenu lt P1 rEAd gt and then Fnnd no filter disabled Fnnd YES filter enabled Return to weighing See 11 2 2 23 13 4 Tare function This parameters enables users to configure a tare function Procedure e Enter the submenu lt P1 rEAd gt and then tArA AtAr automatic tar
27. libration procedure triggered off by the temperature change starts with checking which is signalled by the following message 54 Ca Then the program automatically goes to the internal calibration procedure which is signalled by the following message After completion of the calibration process program returns to the weighing mode libration triggered off by timer The time condition for subsequent automatic calibration is 3 hours It means that when no other triggering factor appear the calibration will appear every 3 hours The calibration procedure triggered off by the time change starts with checking which is signalled by the following message Then the program automatically goes to the internal calibration procedure which is signalled by the following message The program for non verified scales has a parameter for setting a maximal time interval between subsequent internal calibration Procedure Enter the submenu P6 CAL and then 55 select a digit value j 0 89 After completion of the calibration process program returns to weighing mode e Calibration process can be terminated anytime by pressing which is signalled by the following message on the display Notice 1 It should be remembered that internal calibration should be performed with unloaded pan with keeping possibly constant ambient conditions 2 Ifthe calibration process lasts longer than 15 secon
28. menu is divided into 6 basic submenus Each group has its own characteristic name preceded by the letter P and a number P1 rEAd P 1 1 Fil 3 P 1 2 Auto YES P 1 3 tArA no P 1 4 Fnnd YES P2 Prnt P2 1 Prn StAb P2 2 S Lo P2 3 bAud 9600 P2 4 S rS 8d1SnP P3 Unit P3 1 StUn kg P4 Func P4 1 FFun ALL P4 2 Funi no P4 3 Pcs no P4 4 HiLo no P4 5 PrcA no P4 6 Prcb no P4 7 AtAr no P4 8 toP no P4 9 Add no P4 A AnLs no PA b tArE no P5 othr P5 1 bL Auto P5 2 bLbt 70 P5 3 DEEP YES P5 4 tl Auto P5 5 CHr6 YES P6 CAL P6 1 Stu FUNCTION P6 2 uCAL FUNCTION P6 3 CA C 0 P6 4 CA r YES 11 2 Browsing user menu Use scale s keys to move inside the menu 11 2 1 Keypad ORG GRG i 1l OLOA lO tO m n eo Entering main menu Inscribing tare value Increasing a digit value by 1 moving down in the menu Battery accumulator state monitoring Toggling between gross net values oelecting the parameter or changing the value of a selected parameter Entering the selected submenu or activating a parameter for changes Confirmation enter Leaving without changes or reaching a higher level of the menu 11 2 2 Return to the weighing mode lt SAuE gt appears on the display Then press The changes that have been introduced should be saved in order to keep them in the memory for good C While leaving para
29. meters press L s J key until the text to save changes or L s J to leave without changes 15 12 WEIGHING Put a load you want to weigh on the weighing pan When the a pictogram appears it means that the result is stable and ready to read In order to assure long term operation and appropriate measurements of weighted loads following precautions should be taken into consideration e loads should be placed on the pan delicately and carefully in order to avoid mechanical shocks e loads should be placed centrally on the pan errors caused by eccentric weighing are outlined by standard PN EN 45501 ch 3 5 and 3 6 2 12 1 Tarring In order to determine the net mass put the packaging on the pan After stabilising press e Net pictogram will be displayed in the left upper corner and zero will be indicated B850 non After placing a load on the weight pan net mass will be shown Tarring is possible within the whole range of the scale After unloading the pan the display shows the tarred value with minus sign Gus Li Notice Tarring cannot be performer when a negative or zero value is being displayed In such case Err3 appears on the display and short audible signal will be emitted 12 2 Inscribing tare value You can also inscribe a tare value While in weighings mode press e Press simultaneously e and e e You Will see 17 a e Using and e set the
30. n parameters Procedure e Enter the submenu lt P2 Prnt gt and then Bd ISoP folser Gd ISEP 1d i5oP Odc5aP Gd iSaP 7d2SnP data bits 2 stop bits no parity control 7d1SEP data bits 1 stop bit EVEN parity control 7d1SoP 7 data bits 1 stop bit ODD parity control 8d1SnP 8 data bits 1 stop bit no parity control 8d2SnP 8 data bits 2 stop bits no parity control 8d1SEP 8 data bits 1 stop bit EVEN parity control 8d1SoP 8 data bits 1 stop bit ODD parity control Return to weighing See 11 2 2 28 15 OTHER PARAMETERS The user can set parameters which influence the scale operation They are gathered in the submenu lt P5 othr gt e g backlight and beep signal Enter this submenu lt P5 othr gt according to chapter 11 2 15 1 Backlight function Program recognises the way the scale is supplied mains battery and automatically selects the way of operating on the backlight bl for mains blbt for batteries or rechargeable battery pack 15 1 1 Backlight for supplying from mains Procedure e Enter the submenu lt P5 othr gt and then bL no backlight switched off bL YES backlight switched on bL Auto backlight switched off automatically if indication becomes stable for about 10s 29 Return to weighing oee 11 2 2 Notice When bl Auto and the indication has not changed for 10s the backlight is automatically switched off The backlight is switched on
31. on verified scales Not accessible in WLC C 2 scales of WLC series The scale can require only adjusting new start mass In this scale adjusting start mass can be excluded from the process of calibration and performed separately 58 Procedure e Enter submenu lt P6 CAL gt and then e he process of start mass adjustment can be terminated by pressing O which is signalled on the display e Return to weighing with saving changes that have been made Caution If the start mass adjustment lasts longer than 15 the lt Err8 gt message will be displayed and short audible signal will be emitted Press s to perform calibration again with more stable ambient conditions 59 18 COOPERATION WITH PRINTER Each time the key is pressed a current mass value together with mass units is sent to RS 232 interface Depending on setting of STAB parameter it can be printed out with temporary or stable value Depending on setting of REPL parameter printout will be automatic or manual One of thermal printer in KAFKA series can cooperate with each platform scales a KAFKA Only result of weighing with mass unit can be printed b KAFKA 1 Z This printer is equipped with an internal real time clock Both date and time can be printed c KAFKA SQS This printer is equipped with an internal real time clock and possibility of running statistics from measurements Statistic contents quantity of samples sum of masses of
32. ople e Removing or destroying protection stickers Warranty conditions outline the warranty period for rechargeable batteries attached to the device for 12 months The detailed warranty conditions one can find in warranty certificate Contact with the central authorized service 48 48 384 88 00 ext 106 or 107 4 MAIN DIMENSIONS 128 128 i d a E m Rm Scales WLC A 1 C 2 BB Scales WLC B1 Scales WLC C 1 R Scales WLC C2 K 8 9 UNPACKING AND ASSEMBLY e Unpack and put the scale on a flat even stable surface far away from sources of heat e Remove the transport protection Scales WLC C 2 Scales WLC B1 Scales WLC C K WLC C R e Install the weight pan according to the drawings below Scales WLC A1 C 2 scales WLC A2 WLC A2 C 2 scales WLC B1 scales WLC C K scales WLC C R 6 GETTING STARTED e After unpacking and mounting the scale level it out Use levelling legs and the level condition indicator installed in the basis of the scale level OK level incorrect fa e urn the device on using the 9 key keep pressing the key for about 0 5 sec e Wait for the test completion e hen you will see zero indication and pictograms 0 zero indication b d stable result kg weight unit e fthe indication is not zero press key 10 Caution In case of verified scales in ll OIML class with
33. play will not indicate the mass of weighed load but deviation of the load mass placed on the pan referring mass of standard in 96 Return to weighing e Press the Les key twice 42 16 6 Automatic tare This function is useful for fast net mass determination of weighed load in case when tare value of is different for each load In case when the function is active the cycle of scales operating looks as follows press zeroing key when the pan is empty place the container for pieces when indication is stable automatic tarring of the container mass will be performed Net marker will appear in the upper part of the display place a sample into the package display will indicate net mass of sample remove the sample together with the container display will indicate tare mass with minus sign place a container for the next sample When indication is stable automatic tarring will take place Net marker will appear in the upper part of the display place next sample into the package Procedure Return to weighing e Press the zz key twice 43 16 7 Measurement of maximal force on the pan latch Procedure e Enter to lt toP gt function e Confirmation of choice of toP function is indication of the Max pictogram e Apply a force to the weighing pan e he display of scale will latch the maximum value of the force e Remove loads from the pan e Before the next measurem
34. quantity of pieces on the pan and confirm it when stable signalled by i a e he program will automatically calculate the mass of a single piece and go on to the Piece Counting mode pcs You will see the following display Notice 1 lf a user presses the key when load is not present on the pan the message Lo will be indicated for a few seconds and the scale will automatically return to weighing 2 In order to comply with the rules of appropriate counting pieces put as many pieces as possible during unit mass adjustment Single piece mass should not be less than 5 divisions 3 lf a single piece mass is lower than a reading interval d the display will show the Err5 message see ch 21 Error messages and short audible signal will be emitted than the scale returns to weighing 38 Return to weighing e Press the Es key twice 16 4 control referring to the inscribed standard mass Procedure e Enter to lt HiLo gt function e he program enters the window of setting the lower threshold of weighing Min e The inscribed value confirm by pressing L the program will automatically go to the higher threshold of weighing Max 39 e heinscribed value confirm by pressing Q the program will automatically go to the main window e During setting threshold values following cases take place load mass below the threshold load mass between the thresholds
35. ribed in details further in this manual 12 10 INSCRIPTIONS ON THE DISPLAY No Text string Description 0 3 rt Fiere 2 baud Trmsmssonbadas 3 rcs Prececountng 4 Hie w conto according to a standard mass s re Automatcprinout e sub The condition ofprining data SSCS 7 auto Autozerocomrecion LEN Power save time to switch off while no operation Latch of the max measurement Totalizing m ams Weighinganimais a2 WE Memory of Starevalues SSS 13 Indication in autozero zone indication exact zero 4 mug Stableresult readytoread OOOO 45 PCS operation mode counting pieces m ko Opesonmode weghng de Net Tarefunctionhasbeenused control with reference to the standard mass setting the lower threshold or mass below the first threshold control with reference to the standard mass load mass between the thresholds control with reference to the standard mass setting the upper threshold or mass over the second threshold 22 CALIb The stability test for the internal calibration procedure 23 CAL H Manual internal calibration CAL A Automatic internal calibration after powering up CAL t Internal calibration triggered of by temperature CAL C Internal calibration triggered of by timer 27 Terminating of internal calibration 13 11 USER MENU 11 1 Submenus User s
36. rinter press e to print press L amp J to cancel e he following message will appear on the display o e Press g key to return to weighing O e Press lEs to return to totalizing Notice In case of overflow of the range of the display in totalizing you will see lt 5 FULL gt message in the display In that case unload the pan and press e to complete the procedure with a printout of sum of all weighings or put a lower mass on the pan which does not cause the overflow error 47 16 9 Weighing animals Procedure e Enter to lt AnLS gt function a aats e he tinnE message appears on the display for 1s and then the program goes to the window of setting the duration time in seconds of the animal weighing process e Confirm the selected value by pressing e You Will see the following window 48 e Load an animal to the platform e After exceeding the LO value see 14 2 program starts the weighings process The appearance of subsequent hyphens lt gt showing the progress e After completing the process of weighings the result is latched on the display and additionally the OK pictogram is shown in the upper part of the display Q pressing lEs e After removing the animal from the platform program returns to the window Return to weighing e Press Lis 16 10 Tare memory Users are allowed to Enter Up to 9 tare values to the memory
37. scale terminal has been designed for communication between RADWAG scales and external devices via RS 232 interface B It consists of commands sent from an external device to the scale and a responses from a scale C Responses are sent every time after receiving a command reaction for any command D Using commands allows users to receive some information about the state of scale and or influence the operation e g e Requesting weighing results e Display control 20 2 A set of commands for RS interfaces Switch on continuous transmission in current unit Switch off continuous transmission in current unit Send all implemented commands Switch on continuous transmission in basic unit Switch off continuous transmission in basic unit Notice 1 Each command have to be terminated in CR LF 2 The best Policy for communication is not sending another command until the former answer has been received 62 20 3 Respond message format After sending a request message you can receive XX vCRLF command comprehended but the indication below the ES CRLF Command not comprehended error while executing command time limit for stable result XX ECRLF dise DT exceeded limit time is a descriptive parameter of the scale XX command name substitutes spaces 20 4 Command s description 20 4 1 Zeroing oyntax Z CR LF Possible answers Z ACRLF command accepted and in progress Z DCRLF command completed Z ACRLF
38. tion is sent after the scale stabilizes e any the indication is sent immediately after pressing the key this state is assign with in the printout 14 1 Printout type This parameter is to select the type of printout Procedure e Enter the submenu lt P2 Prnt gt and then 25 no5t fib Catb 5th Cath EPL Pr n noStAb immediate printout not accessible in verified scales Prn StAb sending stable results Pr n rEPL automatic operation Pr n CntA continuous transmission in basic unit Pr n Cntb continuous transmission in present unit Return to weighing see 11 2 2 14 2 Minimal mass threshold This function is necessary while working with automatic tare or automatic operation or weighing animals Automatic tarring will not be applied until the indication gross is lower than the value inscribed in S Lo parameter In automatic operation measurements net are sent via RS232 when the indication is equal or greater than the value inscribed in S Lo parameter Weighings animals is performer when the indication is equal or greater than the value inscribed in S Lo parameter Procedure e Enter the submenu P2 Prnt and then 26 0 0 9 j select a digit CA e select a digit value J Return to weighing see 11 2 2 14 3 Baud rate Procedure e Enter the submenu lt P2 Prnt gt and then f Return to weighing see 11 2 2 14 4 Serial transmissio
39. tomatically goes to the internal calibration procedure which is signalled by the following message After completion of the calibration process program returns to the weighing mode Calibration process can be terminated anytime by pressing which is signalled by the following message on the display Notice 1 It should be remembered that internal calibration should be performed with unloaded pan with keeping possibly constant ambient conditions If the calibration process lasts longer than 15 seconds scale software will react with lt Err8 gt displayed and a short sound and then the calibration procedure will start again 53 lt 17 1 2 Automatic internal calibration The automatic calibration process can be triggered off by 3 different factors e Calibration after powering up After performing the start procedure the scale program starts to check stability conditions for the calibration process and displays the following message Then the program automatically goes to the internal calibration procedure which is signalled by the following message After completion of the calibration process program returns to weighing mode e Calibration triggered off by temperature changes The scale has been equipped in the temperature monitoring system Temperature triggers off calibration every time when the internal system measures the temperature change greater than 3 C The ca
40. too low level of voltage is measured by software the pictogram is displayed It means that charging or exchanging batteries is required 15 4 1 Checking the batteries This function is to check the level of battery supply It works only if e Weighing mode is set e Battery supply is set in parameters 285 Procedure After displaying the level of batteries in per cents the program returns to weighing 15 4 2 Battery discharge pictogram The symbol bat low switches on when the voltage level drops to 18 of the accepted level of voltage It means that charging or exchanging batteries is required Low level of batteries e pictogram on the display e After some time the device will automatically switch off to protect the batteries from destructible discharging e Charging is signalled by blinking period about 2 seconds on the display 15 4 3 Accumulator charging option This function allows to switch on charging algorithm for NiMH batteries for scales of WLC C1 C2 WLC B1 series or a gel cell SLA accumulator for scales of WLC A2 WLC C 2 series a Parameter lt CHr6 gt set to lt no gt e Pictogram does not appear charging disabled e During software initializing after turning on lt bAtt gt b Parameter lt CHr6 gt set to lt YES gt e Pictogram blinks slowly period about 2 seconds charging is enabled 33 e Message nlmh appears on the display for scales of WLC C1 C2
41. ual ales WLC series VETEK Scandinavia s biggest webshop for scales Vetek Weighing AB Box 79 S 76040 V dd Sweden Phone 46 176 20 89 20 fax 46 176 20 89 29 info vetek com www vetek com JANUARY 2009 No TABLE OF CONTENTS MI Ig BRE IIS c cc eee te eee nce eee oem eemeutmae ences ten sence otencuepancee 5 MA PRG ipo C E 6 2 1 MalhterTariGes em eee tc xn ner ee t a DLP E Lt IDE EU 6 2 2 OWEN SUD DIN cates statutes m o seen chee latina conch eee al euch eed duet prc Mou dau dete feda tret e em deu 6 3 WARRANTY CONDITIONS ket a euuu ambu a Aaaa 6 4 MAIN DIMENSION S c comua outs ed sm ce as ees 7 5 UNPACKING AND ASSEMBLY epu qmucia mette teeth aa aaa a ae eben en adeo ean Ion Ne Onus 9 60 GOING STARTED ec a ees we che eae techie a aaa 10 DL BALANCE LEVELLING saa a e e ec ceed 11 Be KEYPAD c 11 9 KEYS FUNC BIO c M 12 10 INSCRIPTIONS ON THE DISPLAY 4 dare pce aer sacan pusiu adt eo ecco cstey co bou Mee eoo tees ra 13 iut idu le r 14 13 15 SUDO LIS actio crate tiers dete Sate ance Miacm eher Ec usnm IM THEE ex Deporte a encd E 14 eZ Tro ineunt eT harabdachdoute ta ticweee 15 UNISEX YP a MeL 15 11 2 2 Return to the Weighing mode teta oreet an desees vein conve u uu d
42. umidity and temperature For assuring the maximal accuracy of weighing a periodical user calibration is required Calibration should be performed e Before weighing process e After a long break between series of measurements e After the ambient temperature change Conditions of trigerring off calibration e Automatic internal calibration Started by adequate temperature change Started after adjusted time period Started after powering up the device e Manual internal calibration started from the keyboard e Calibration with an external weight Caution Internal calibration is accessible only in WLC C 2 scales of WLC series In WLC C 2 scales calibration with an external weight is not accessible It should be remembered that the calibration process should be performed with the empty pan The calibration process can be terminated by pressing Esc when necessary 17 1 Internal calibration An option for WLC C 2 scales of WLC series only The internal calibration process can be initiated manually or automatically Press Cal to initiate it manually Automatic calibration system performs internal calibration and informs a user on the display about the course of the process 52 17 1 1 Manual internal calibration Procedure While in weighing mode press The scale program starts to check stability conditions for the calibration process and displays the following message Then the program au
43. ustified to the left command 3 characters justified to the left Example 1 ee 1832 0 g AJ GCRLFE the printout generated from the scale after pressing ENTER PRINT Example 2 2 237 b CRLF the printout generated from the scale after pressing ENTER PRINT 0 000 kg CRLE the printout generated from the scale after pressing ENTER PRINT 68 20 6 Continuous transmission The indicator can work in a continuous transmission mode It can be switched on or off in parameters or using RS232 commands The frame format sent by the indicator in case of setting lt P2 Prnt gt to CntA Be eee Stability character space if stable if not stable if an indication over the range v if fan indication below the range sign space for positive values or for negative values mass 9 characters justified to the right unit 3 characters justified to the left command 3 characters justified to the left The frame format sent by the indicator in case of setting lt P2 Prnt gt to Cntb PPP ee Perl 20 7 Configuring printouts General information If some information included are redundant or not sufficient and there is a necessity of changes one can design their own protocol format in EDYTOR WAG computer program This piece of software is accessible in http www radwag com 69 21 ERROR COMMANDS Err2 Value beyond the zero range Err3 Value beyond the tare range Err4 Calibration mass or start m
Download Pdf Manuals
Related Search