Instruction manual
Contents
1. 2 Silk drainage pipe T Drain bracket 4 mm hole Drain tube nut BA UO compact engl doc s m AW CITC 4 FUNCTIONING 4 1 FIRST START UP WARNING The first start up of the machine must be done by the installer The installer checks the correct functioning of the machine WARNING Before start up the osmosis turn the bypass valve to BY PASS position and make the start up of the softener as described in the attached manual Once done the softener start up turn the bypass valve to OPEN position and start the osmosis machine Insert the power plug in a grounded socket 230V 50Hz the machine is ready to operate It is necessary to fill the dishwasher once with the new installed UO COMPACT 150 and drain the dishwasher one time completely 5 y Check leakage the hydraulic circuit 4 2 NORMAL USE The machine starts and stops automatically leaded by the internal max pressure switch when the dish washmachine downstream requires water ts During normal use the manual bypass valve must be in OPEN position WARNING Ls Avoid dehydration of the membranes as it will cause them to malfunction 4 2 1 Automatic flushing function In order to avoid bacterial growth on the surface of the membrane the device will automatically opera2. ATTENTION UO COMPACT 150 is not a water purifier Using UO COMPACT 150 to condition water that is not drinkable is ABSOLUTELY PROHIBITED 2 2 SCHEMATIC REPRESENTATION I SOFTENER DRAIN SCHEMATIC REPRESENTATION SET 3 5 bar LEACKAGE _J PROBE OLLECTOR BLOCK BA UO compact_engl doc e m rl 2 3 DESCRIPTION There are four external hydraulic connections on the back of the device respectively for the inlet water 2 G the outlet water 4 G to the dish washmachine the osmosis drain 1 4 diameter and the softener drain barb hose 12mm On the rearside of the machine there is also the power cord the knob of the manual bypass valve and air vents There is an electronic display screen attached to the front of the device providing the user with important messages regarding the correct operation of the machine From the connection to the inlet the water arrives to the softener then after the softener to the manual bypass valve The brine tank is accessible opening the top left cover The valve has three positions open bypass and closed In the open position water flows to the hydraulic components of the machine for standard operating In the bypass position the osmosis devic
3. Electric faucet signal not used Motor Motor Solenoid valve EV1 Solenoid valve EV1 Solenoid valve EV2 not used Solenoid valve EV2 not used Power supply 230V Power supply 230V use CH I XR OI O oO ev EE VV 7 TROUBLESHOOTING Ke Electric supply failure For the softener troubleshooting see attached manual Check power plug is connected Burned fuse Check power socket fuse and electronic board fuse Display cable removed Check display cable is connected on the board socket Damaged board Replace the board Water inlet pressure failure With a manometer check that dynamic water inlet pressure is at least 1 kPa Inlet solenoid valve failure Check water inlet solenoid valve functioning if damaged or clogged replace it Low pressure switch failure Check pressure switch functioning if damaged replace it Damaged board Replace the board Filter clogged Replace the filter Electric connection failure Check electric connections and tight if necessary Leakage Open the machine and check carefully all hydraulic circuit for leakages Leakage probe in short circuit Check water leakage position if directly at contact with metal parts of the machine place in a different position Damaged board Replace the board Damaged board Replace the board Blocked
4. Het symbool van de versperde vuilnisbak herinnert aan de verbruiker dit product niet weg te gooien als een niet geclassificeerd gemeentelijk afval eee sev ev cum a VV term IC ATTACHMENT I CE declaration C DECLARATION OF CONFORMITY THE PRODUCER EVOWATER eve ERU Falkenstr 2 awa 1 h 72589 Germany DECLARS THAT THE PRODUCT UO COMPACT 150 DISH WASHMACHINE TREATMENT WATER DEVICE IS DESIGNED AND BUILT IN CONFIRMITY WITH THE FOLLOWING DIRECTIVES MACHINES 2006 42 EC LOW VOLTAGE 2006 95 EC ELECTROMAGNETIC COMPATIBILITY 2004 108 EC HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES SAFETY 60335 1 2004 The manufacturer also declares that the technical construction file is kept by EVOWATER Cr Ce ATTACHMENT Spare parts UO COMPACT 150 Spare parts for routine maintenance Code Description Code Description l Kit with 2 membranes 3012 with Y21409B Bii S 8096072 vessel tested and sealed with cartridge caps 8096070 1 pump 300 sealed with 5200152 Solenoid valve 3 8 FF 230V faston Spare parts for extraordinary maintenance Code Description Code Description 1100128 Vessel 3012 8096071 Ge ER with Y21305B aa Head single side w round
5. 5 GENERAL 54 5 mee reor UR Rex eR E y E E RYE ERE 7 2 6 INTERNAL LAYOUT e peaux E E deeg SE EE EES EE EES 7 3 INSTALLATION a darsin 8 3 1 DRAIN BRACKET TYPICAL INSTALLATION Zeene geg g Some note EE ER de E C ER VERE EE coma 9 4 duele lc 10 4 1 EE EE 10 4 2 Qe MUS 10 4 3 MANUAL Besse geed ES ERO SUO BRI RN KREDITE DU OR eg 10 4 4 ELECTRONIC BOARD FUNCTIONING DRM EP CU EE 11 4 5 INFORMATION PAGES eege SSES SE SEENEN 12 4 6 cnc 13 5 ENDUSER ORDINARY 15 5 1 eet 15 5 2 SOFTENER SALT 2 NO RIOT QE EQUI e uve ege geg 16 6 PROFESSIONAL EXTRAORDINARY 17 6 1 REQUIRED TRAINING FOR MAINTENANCE HH He eme en nn nnn 17 6 2 RESPONSIBILITIES OF MAINTENANCE PERSONNEL III HH He ee He he ehe ese nenne 17 6 3 PUMP REPLACEMENT IURE Ve OUR ERES TOES 18 6 4 SOLENOID VALVE INTERNAL CLEANING REPLACEMENT He He he n nnns 18 6 5 CHECK REPLACEMENT OF OSMOTIC MEMBRANES csse He He Hesse he eh ee e e
6. The drainage flow is also used to cool the motor with a cooling copper pipe and than coupled to the drain connection The calibrated drain capillary is used to set the drain flow Permeate water is controlled by a conductivity probe wired to the electronic board in chase of high conductivity gt 70 uS cm after 50 seconds from operative start the board shows high conductivity alarm After four consecutive high cond alarms the machine also makes three beeps after 50 seconds from operative start if high cond alarm occurs For automatic start stop of the machine a check valve and a max pressure switch are installed in the permeate collector block On the bottom there is a leakage probe if leakage occurs the machine stops automatically and makes acustic and visual alarm The machine is equipped with four wheels with breaks WARNING The overall water quality depends on a number of variables the concentration of saline properties in the water along with other retained elements the temperature water pressure and the total solubility of salt The water quality may also vary according to the kinds of salts or elements found in the local water source The treatment of water coming from a source that is particularly polluted with high concentrations of impurities can cause the blockage of the membranes of the filters and or impede the overall water flow This device CANNOT be used as a substitute for a government approved desalinization and anti b
7. compact_engl doc Wassertechnische Systeme 2 5 GENERAL DIMENSIONS 2 6 INTERNAL LAYOUT 1 Softener 2 Filter cartridge 3 Filter head 4 Electronic board 5 Solenoid valve 3 8 G 6 Max pressure switch yx sA cu ra e 4 A Pd rd S 1 2 KU 2 BA UO compact engl doc 7 Softener connections 8 Min pressure switch 9 Motor 180W 10 Pump 3001 11 Membrane housing 3012 300gpd 12 Membrane head m 7 KE E Sa im f 15 hs Se Ki N 5 we Y S K Em e N N 22 d m 2 E ev m water rev m EN rum 3 INSTALLATION The installation of the UO COMPACT 150 must be performed by qualified personnel in accordance with applicable laws and standards The machine has connections for inlet water outlet water osmosis drain and softener drain Once done the hydraulic connection connect the power cord During normal operations the bypass valve must be in OPEN position WARNING Please avoid exposure to sudden changes in temperature thereby causing internal condensation to form and damage electronic parts Please ensure that the grill panel is never obstructed which could lead to the overheating of the motor of the device INSTALLATION CHECK LIST The EU approved ground cable of the power supply must be connected to the device The power suppl
8. data the display will show data saved and will return to program pages Reset gt Filter The first page displayed is Filter reset page enter with the key The display shows Press E Reset confirm Filter reset with the key the Press board will then display data saved Reset Setting Faucet Scroll to the next page with the key enter faucet type selection with the Faucet key Choose faucet type manual or electric with the keys electric and confirm with the key The board will show data saved Ls If manual faucet is selected the high cond alarm function is disabled Setting Customer Scroll to the next page with the key enter customer setting page with the key gt Select EVO WATER UO COMPACT with the keys and WATER gt and confirm with the key The board will show data saved BA UO compact engl doc a m AW CITC Setting Scroll to the next page with the key enter functioning mode page with the Mode key Select time limited functioning or no limit functioning with the keys O O Time and and confirm with the key The board will show data saved ts In Ho Re Ca applications it is recommended to set Time Limit Functioning Setting Scroll to the next page with the key enter liters hour conversion K convrs parameter with the key Modify the value with the keys 0120 and co
9. 163 Elbow 3 8 9300258 Male connector 8x3 8 BSP P 9300400 T 6mm CV AN Sn VV ATTACHMENT CE LABEL enm CC EVOWATER F 2 72583 Germany zl enz Ivo 230V 202 1 5A UO KOMPACT 150 2 m ATTACHMENT IV Maintenance Log INSTALLATION TECHNICIAN DATE SIGNATURE REGULAR MAINTENANCE TECHNICIAN DATE SIGNATURE
10. 8098000 Electronic board think ro 9400330 Bypass valve 4 8096075 re dab Swich wining and 1100126 O ring 3 53x4 34 8096073 Cond Probe 3 8 K5 w o ring 1100166 O ring 2 62x13 95 1100232 O ring 1 78x11 11 1100258 O ring 3x9 1196078 Bumper MF d 20 h 25 M6 Max pres switch 74 100 600 kPa 8000112 Leakage probe 8096074 w o ring Pipe fittings and components for installation Code Description Code Description 1196117 Block 35x35x92 4 M 9300359 Stem adapter 10 x3 8 bspp 1197032 Check valve insert DW10 9300383 Stem elbow 4 8096060 Assembled permeate block 9300679 Elbow 3 8 5 16 9300121 Bulkhead 3 8 out 9300388 Stem elbow 6mm 9300164 Elbow 6mm 9300391 Stem elbow 8mm 9300170 Elbow 8mm 9300392 Stem elbow 10mm 9300174 Elbow 10mm 9300403 T 8mm 9300175 Elbow 12 6mm 9300404 T reduced intermediate 10 6 mm 9300221 10mm 9300469 Famale adapter 6 x 4 BSP P 9300257 Male connector 8x1 4 BSPP 9300518 Stem elbow 10 8 mm 9300259 Male connector 10 x 1 4 BSP P 9300518 Stem elbow 10 8mm 9300260 Male connector 10 x 3 8 BSP P 9300671 Bulkhead MF 3 4 3 8 9300272 Male connector 3 8 x BSPT 9300672 Power fitting elbow 74 3 8 9300298 Plug 4 9300675 Reduction 74 5 32 9300310 Reduction 4 6mm EE AFERO 9300338 Stem adapter 8 x 4 BSPT 9400330 Panel mounted bypass valve 9300339 Stem adapter 8 x 3 8 BSPT 9400331 Nut 34 brass 9300357 Stem adapter 8 x 3 8 BSP P 9300
11. FEM 1 6 6 POWER CABLE REPLACEMENT d If the supply cord is damaged it must be replaced by the manufacturer or by the authorized technical personnel in order to avoid a hazard BA UO compact engl doc Pelle WassertschnischeSystemo AAO 6 7 MACHINE SANITATION a Vata Perform the sanitation if permeate water has a bad smell All sanitation operations must be performed by qualified personell Use protective clothing to the skin hands and eyes as shown in the safety data sheet of chemicals used Disconnect the permeate pipe and fill a tank with approx 3 5 liters of permeate water Add 250ml hydrogen peroxide 10 vol 8 to achieve a concentration of 0 2 by weight Connect the water pipes of entry drain and permeated by the machine at the tank make a bridge on the low pressure switch connectors Turn on the machine and let the solution recirculate for 10 minutes Wait 10 minutes that the solution acts on the machine Reconnect the inlet drain and permeated pipes Replace the filter and reconnect the cables of the minimum pressure switch Turn on the machine fill and empty the dishwasher tank once until the sanification solution resids are totally drained 6 8 FREEZE PREVENTION TREATMENT 4 S Perform the freeze prevention treatment if after the start up the machine will be stocked below 0 C The operation must be performed by qualified personell Disconnect the per
12. IVITY PROBE CONNECTORS Disconnect the connectors of the conductivity probe Clean the male and female connectors from possible oxidation Tighten the connector with pliers and reassembly Perform conductivity calibration Be E Clean the gr conductivity probe connectors if the measured value is not correct BA UO compact_engl doc rV AW CITC 6 11 ELECTRONIC BOARD EXTRAORDINARY MAINTENANCE Remove the top cover of the machine accessing the tray card Remove the cover of the electronic box If the fuse is burned replace with another one Check the tightness of main terminal connector and of the display connector If the board continues to malfunction replace with another one following these steps Unscrew the screws fastening the electronic board box and remove support plate Remove the electronic board box and disconnect the main connector Mount the new electronic board with reverse procedure a a 1 Electronic board 2 Display electronic board 3 Fastening screw 4 Board support plate Conductivity adjustment trimmer Display connector Terminal board connections 18 Conductivity probe 17 Conductivity probe 16 Leakage probe d E 90000000 RG BA UO compact engl doc 15 Leakage probe 14 Max pressure switch 13 Max pressure switch 12 Min pressure switch 11 Min pressure switch 10 Electric faucet signal not used
13. Ire m Wassertechnische Systeme Wa te MANUAL use and maintenance 150 Before introduction of the softener the installation guide has to be read carefully For any disturbances cause by disregarding the instructions evo water doesn t accept liability SERIAL NO PART NUMBER evo water oHG FalkenstraBe 2 72589 Westerheim Tel 49 7333 9 5 08 77 Fax 49 7333 9 5 30 25 www evo water com info evo water com BA UO compact_engl doc nre me Wassertechnische Systeme Wa teram INDEX 1 GENERAL INFORMATIONS snnt ates ate setas ansias assa snas snas snas ss assa assa assa assa assa ass ass asma asma a 3 1 1 MANUFACTURER 7 ASSISTANCE 3 1 2 CERTIFICATION m 3 1 3 PURPOSE OF THE MANUAL AND ITS CONTENTS IH He He HH me se e essen nenne 3 1 4 CARE AND STORAGE OF THE MANUAL eere er iE EE REES EE EES 3 1 5 IMPORTANT SYMBOLS TO REMEMBER ees nen ne hen Ee EEN 3 2 CHARACTERISTICS OF THE 4 2 1 RECOMMENDED USE 5 err eer rx ERR pessoas EE EEUU UP M DRIN UPON ane AN E oe EEN 4 2 2 SCHEMATIC REPRESENTATION ee eege ER 4 2 3 DESCRIPTION 255255 M 5 2 4 TECHNICAL SPECIFICATIONS 0 0 ee rx ERE E RUE EURO EES RE 6 2
14. acteriological plant BA UO compact engl doc s m SS ee VV CITC hl 2 4 TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Height x Width x Depth vertical position 380X533X544 mm Approved level of safeguards and protections IP23 Weight 40 kg Approved Decibel Level under normal operating conditions 55 dB A Max umidity 95 96 WATER SUPPLY SPECIFICATIONS Water type POTABLE Maximum temperature 35 Minimum inlet capacity 300 Minimum inlet pressure 100 kPa Maximum inlet pressure 600 Kpa POWER SUPPLY SPECIFICATIONS Power supply type SINGLEPHASE GROUND Voltage 230 V Frequency 50 Hz Absorbed current 1 5 A Fuse type electronic board T3 15A PERMEATE WATER SPECIFICATIONS Minimum capacity at 15 90 h OPERATION UNDER NORMAL WORKING CONDITIONS Activated carbon filter 200h max 6 months R O Membrane When high cond alarm occurs gt 70 16 Vane pump and solenoid valve 2 000 h DRAIN CAPILLARY COLOUR AND RECOVERY RATIO MATRIX Minimum capacity at 15 90 Q The machine must not be installed with inlet water gt 1200 uS WARNING Any use of this device which has not been stipulated in this manual will constitute IMPROPER USE thereby rendering the guarantee null and void The manufacture Ls WILL NOT be liable for any damages caused by the IMPROPER USE of this device due to negligence failure to follow the manual or permitting unauthorized maintenance personnel to tamper with machine BA UO
15. c hygiene e General familiarity with the device in addition to a basic knowledge of troubleshooting electrical and hydraulic problems 6 2 RESPONSIBILITIES OF MAINTENANCE PERSONNEL The overall maintenance plan described in this chapter must be rigidly adhered to as indicated in the above paragraph in order to maintain the efficient operation of the device thereby guaranteeing continued water quality The tasks listed in the box below must be performed by qualified technical personnel strictly in accordance with the manual exclusively using approved parts and materials Otherwise the guarantee will be null and void The maintenance performed must always be documented properly and signed by the technician in the space provided on the attached maintenance log OVERALL INSPECTIONS TASK FREQUENCY E pump and solenoid Substitution 2000 hours Membranes Substitution When high conductivity alarm occurs Visual Inspection to check the integrity of system controls Machinery General cleaning In chase of functional damage Operation Verification Machinery Sanitization In chase of permeate water bad smell WARNING The internal electrical system of the UO COMPACT 150 is powered by 230 Volts Prior to remove the covers ensuring that the plug out is diconnected WARNING DO NOT use corrosive products acids steel wool or wire brushes to clean the device DO NOT use low or high pressure jets of water when washin
16. d check water pressure on permeate line Defective pressure switch Check pressure switch functioning if damaged replace it Electric connection failure Check electric connections and tight if necessary Defective pressure switch Check pressure switch functioning if damaged replace it Damaged board Replace the board BA UO compact engl doc ev cum Wassertechnische Systeme te mo WASTE OF ELECTRICAL ELECTRONIC EQUIPMENT RACCOLTA RIFIUTI DI MATERIALE ELETTRICO ELETTRONICO RECOLHA DE RES DUOS DE MATERIAIS EL CTRICO ELECTR NICOS ABFALLENTSORGUNG ELEKTRISCHES ELEKTRONISCHES MATERIAL RECOGIDA DE RESIDUOS ELECTRICOS ELECTRONICOS COLLECTE DES D CHETS DE MAT RIEL ELECTRIQUE ELECTRONIQUE VERZAMELING AFVAL ELEKTRISCH ELEKTRONISCH MATERIAAL UK EU directive 2002 96 EC classifies this product as an electrical or electronic tool Do Not dispose of this tool as unsorted municipal waste Dispose of this tool at a collection or recycling centre according to local and national law The consumer has an important role in reducing the disposal of waste by returning waste electronic electrical tool for recycling Recycling avoids the dispersion of hazardous materials into the municipal waste stream The crossed out bin symbol reminds the user not to dispose of this product as unsorted municipal waste 1 Ai sensi dell art 13 del Decreto Legislativo 25 luglio 2005
17. d perform filter reset see next page 4 5 INFORMATION PAGES EVO WATER Microtek Ver 1 21 Manual Flush Flush Reset Filter Press Reset T Remain 0000 00 T Total 0000 00 When the board is in stand by mode the name of the installer is displayed Pushing the key the electronic board software version is displayed To scroll the information pages push key the first page shows the manual flushing page to perform this operation push key During manual flush operation the board displays Flushing and opens the solenoid valve for 1 minute Pushing the key the display shows Reset filter To enter filter reset press the key gt and the confirm Filter reset pressing another time the key the display shows Data saved Pushing for another time the key the next information page shows the remaining time before filter change Pushing for another time the key the page shows the total operating time since last filter change BA UO compact engl doc s m SS ee VV CITC 4 6 SETTINGS PAGES To enter programming mode push the key while you connect the power Settings supply of the machine Press Then push the key gt and confirm programming mode Scroll the pages with the keys and To exit programming mode disconnect and reconnect the power supply Data gt Saved Each time a value is modified push the key to save the
18. e is excluded and softened water is supplied to the outlet of the machine In closed position water flow is closed After the manual valve water arrives to the inlet solenoid valve The water flows then through the quick connection carbon filter The carbon block filter facilitates the elimination of the unpleasant chlorine taste without compromising the desirable mineral properties of the water These activated carbon filters can also absorb potential trace organic micro pollutants various chemicals organic and inorganic i e chlorine composites chlorine residue used to disinfect water haloforms pesticides surface active agents The filter is hidden by the filter cover on the right side After the filter a min pressure switch is attached to check inlet pressure The min pressure switch prevents the pump to run dry In chase of low pressure alarm is displayed and then the machine makes automatic restart after one minute When consecutives low pressure alarm occures the restart delay automatically increases Water is then pumped at high pressure by the brass vane pump connected to the liquid cooled motor The water arrives at high pressure to the vessels contain the reverse osmosis membranes The water permeates the layer flowing into the collection tubes and then it is directed to the main tube of the membrane wrapped in various layers The permeate yield comes from the main tube of the membrane and is sent directly to the outlet
19. ed air Reassembly with reverse procedure To replace the solenoid valve Remove the power plug and open top cover Disconnect coil faston connectors Remove the solenoid valve and unscrew the fittings Install the fittings in the new solenoid valve reconnect piping and electric connectors wm 99 BA UO compact engl doc AW CITC 1 Solenoid valve body 2 Coil fixing screws 3 Fittings 4 Coil faston connectors BA UO compact engl doc re s m SS ee VV CTC 6 5 CHECK REPLACEMENT OF OSMOTIC MEMBRANES Se When high conductivity alarm occurs replace the osmotic membrane as follows Disconnect the tubes from the fittings of the vessel containing the membrane Dismantle the vessel from the machine and unscrew the caps Dismantle the membranes clogged and replace with new membranes of the same type Clean the vessel on the inside by removing all traces of dirt and scale He The new membrane must be removed immediately prior to their installation and handling using protective gloves sterile Before installing the membrane in the vessel lubricate the o ring and the upper seal Install the vessel with reverse procedure Supply water for at least 15 minutes and then check permeated flow and quality Inlet 3 2 Vessel body Permeate Drain Seal Membrane es O rings cd 5 T
20. electr nicos El reciclaje previene la dispersi n de materiales peligrosos en la gran cantidad de residuos municipales El s mbolo del bid n con una banda transversal recuerda al usuario que no debe tirar este producto como si fuera un residuo municipal no clasificado F La directive 2002 96 EC classifie ce produit comme appareil lectrique lectronique Ne pas jeter cet appareil avec les d chets municipaux non classifi s Jeter cet appareil dans un centre de collecte ou de recyclage conform ment la loi locale et nationale Le consommateur joue un r le important dans la r duction des d chets en pr voyant le recyclage des appareils lectriques lectroniques Le recyclage permet d viter la dispersion de mat riau dangereux dans la masse des d chets municipaux Le symbole du bidon barr rappelle l utilisateur de ne pas jeter ce produit avec les d chets municipaux non classifi s NL De richtlijn 2002 96 EC classificeert dit product als een elektrisch elektronisch gereedschap Gooi dit gereedschap niet weg als een niet geclassificeerd gemeentelijk afval Breng dit gereedschap in een verzamel of verwerkingscentrum volgens de plaatselijke en nationale wet De verbruiker speelt een belangrijke rol in het verminderen van het afval door de verwerking van de elektrische elektronische gereedschappen voor te bereiden De verwerking voorkomt de verspreiding van gevaarlijk materiaal in de massa van het gemeentelijk afval
21. g the device BA UO compact_engl doc s m AW 6 3 PUMP REPLACEMENT Remove the top and right panels of the machine Disconnect the piping from the pump fittings Unscrew the screw of the clamp connecting and disassemble the pump Install the new pump with fittings previously removed Mount the new preadjusted and sealed pump with reverse procedure Motor 180W liquid cooled um Brass vane pump 3001 Connection joint lif Fittings Pump bypass Liquid cooling couplings Condenser 7uF Bumpers 6 4 SOLENOID VALVE INTERNAL CLEANING REPLACEMENT If during stand by or with machine OFF the water continues to flow to the drain the solenoid valve never closes inlet water In this chase make internal cleaning of the solenoid valve body If during normal functioning water never flows to the filter and Alarm P Min appears the solenoid valve never opens inlet water In this chase replace the coil or the whole solenoid valve To clean the solenoid valve and or replace the coil Remove the power plug and open top cover Unscrew the three screws that fix the coil to the solenoid valve body Disassemble the coil and internal parts of the solenoid valve If damaged replace the coil clean the body of the solenoid valve with compress
22. mbol Indicates General cautions risk to the operator This symbol Indicates danger of electrical shock or electrocution RESTRICTIONS This symbol indicates general restrictions BA UO compact engl doc rei m n 7 CHARACTERISTICS OF THE DEVICE 2 1 RECOMMENDED USE UO COMPACT 150 is equipment designed for dish glass wash machine water treatment It is able to modify organoleptic and chemical characteristics of potable water reducing saline content UO COMPACT 150 is used to supply treated water to dishwasher and glasswasher machines vry ATTENTION The device is not intended to be used by people including children whose physical sensory or mental disabilities are reduced or lack of experience or knowledge unless they have been granted through the intermediary of a person responsible for their safety supervision or instruction concerning the use of the device Children should be supervised to ensure they do not play with the appliance ATTENTION If the dish wash machine is not equipped with break tank an external pressure tank of at least 16 liters must be installed All components of the dish glass washmachine in contact with water must be compatible with osmosis trated water It is forbidden to use brass use only plastic parts and stainless steel parts The company EVOWATER is not responsible of any demage or injury to things or people if these instructions are not respected
23. meate pipe and fill a tank with 9 liters of permeate water Add 1 of propylenic atossic glycole Connect the water pipes of entry drain and permeated by the machine at the tank make a bridge on the low pressure switch connectors Turn on the machine and let the solution recirculate for 10 minutes Reconnect the inlet drain and permeated pipes and the cables of low pressure switch At the restart after inactivity period fill and empty the dishwasher tank once until the freeze prevention solution resides are totally drained BA UO compact_engl doc i _ teram s m AW CTC 6 9 VERIFICATION CALIBRATION OF THE SETTING The verification calibration of the settings must be done at extraordinary maintenance of the relative items and or on troubleshooting operations switchin the permeate block Install preadjusted to 350 kPa sealed pressure Check pressure with a manometer Ls All the calibrations must be performed by qualified personnel 6 9 1 Max pressure switch setting 1 Adjustment nut 2 COM connector 3 Normally opened contact Install a preadjusted to 30 kPa sealed pressure switch 4 Normally closed contact He on the filter outlet pipe 5 Fitting 74 M Check pressure with a manometer Ls Max pressure switch is wired to COM connector 2 and Normally closed contact 4 6 9 2 Min pressure switch setting BA UO compact_engl doc s m SS ee VV CITC 6 10 CLEANING CONDUCT
24. n 151 Attuazione delle Direttive 2002 95 CE 2002 96 CE e 2003 108 CE relative alla riduzione dell uso di sostanze pericolose nelle apparecchiature elettriche ed elettroniche nonch allo smaltimento dei rifiuti Il simbolo del cassonetto barrato riportato sull apparecchiatura o sulla confezione indica che il prodotto alla fine della propria vita utile deve essere raccolto separatamente dagli altri rifiuti L utente dovr pertanto conferire l apparecchiatura giunta a fine vita agli idonei centri di raccolta differenziata dei rifiuti elettronici ed elettrotecnici oppure riconsegnarla al rivenditore al momento dell acquisto di una nuova apparecchiatura di tipo equivalente in ragione di uno a uno L adeguata raccolta differenziata per l avvio successivo dell apparecchiatura dismessa al riciclaggio al trattamento e allo smaltimento ambientale compatibile contribuisce ad evitare possibili effetti negativi sull ambiente e sulla salute e favorisce il reimpiego e o riciclo dei materiali di cui composta l apparecchiatura Lo smaltimento abusivo del prodotto da parte dell utente comporta l applicazione delle sanzioni amministrative previste dalla normativa vigente P A directiva 2002 96 EC classifica este producto como um instrumento el ctrico electr nico Nao deitar este instrumento com lixo municipal nao classificado Deitar este aparelho em um centro de recolha ou de reciclagem segundo a lei local e nacional consumidor tem uma impor
25. nfirm with the key gt The board will show data saved Setting Time Scroll to the next page with the key enter filters maintenance interval Time with the key gt Modify the value with the keys and h 0142 confirm with the key The board will show data saved Setting Language Move to the next page with the key modify the language parameter with the key Set the language with the keys and confirm with the key The card therefore indicateds Data saved BA UO compact engl doc s m SS ee VV CITC 5 ENDUSER ORDINARY MAINTENANCE The tasks of the enduser are Softener salt refill every month Filter replacement every 200 hours of working ATTENTION Use only original parts EVOWATER WARNING The internal electrical system of the UO COMPACT 150 is powered by 230 Volts A Prior to opening the device remove the cover and or panels and or the protective grill ensuring that the plug has been removed from the electrical outlet WARNING The enduser MUST NOT open the covers of the machine that are fixed with screws DO NOT use corrosive products acids steel wool or wire brushes to clean the device DO NOT use low or high pressure jets of water when washing the device To replace the cartridge follow these steps 1 Open the filter cover pulling right the two locks Turn the cartridge 90 clockwise until the head assembly is in closed position P
26. ped with a leakage alarm system 1 3 PURPOSE OF THE MANUAL AND ITS CONTENTS This manual was written in order to supply the user with all the necessary information needed to facilitate the autonomous and safe operation of this device The manual contains information that is critical to the operation and regular maintenance of the machine WARNING This user s manual can be utilized by both technical and maintenance personnel All users and technicians are required to thoroughly read this manual before gt installing or operating this device In accordance with this manual the user should never perform any unauthorized maintenance exclusively reserved for qualified technicians and maintenance personnel otherwise the guarantee will be rendered null and void 1 4 CARE AND STORAGE OF THE MANUAL The instruction manual is an integral part of this device and must be kept nearby at all times and stored inside the proper container so that it is protected from eventual damage or destruction 1 5 IMPORTANT SYMBOLS TO REMEMBER GENERAL WARNINGS This symbol Indicates warnings or key information regarding the operation of this device Please pay close attention whenever you see this symbol This symbol Indicates that specialized portable equipment may be required to adjust or repair the components of the device This symbol Indicates that a visual or in depth inspection etc of the device may be required INDICATIONS OF DANGER This sy
27. pump Replace the pump Burned motor condenser Replace the motor condenser Burned motor Replace the motor Electric connection failure Check electric connections and tight if necessary Solenoid valve damaged Replace the solenoid valve Coil burned Replace solenoid valve coil Electric connection failure Check electric connections and tight if necessary BA UO compact engl doc ateni re V s AW CITC Clogged solenoid valve Check solenoid valve functioning if clogged replace it Clogged filter Replace the filter Blocked vane pump Replace the pump Clogged membranes Replace the membranes Le Install a manometer on the pump outlet to check operating pressure S 6 8 3 Clogged membranes Checks permeate quality with a calibrated instrument if high cond replaces membranes Conductivity measurement failure Calibrate conductivity probe and clean connectors Exausted filters Replace the filters Biofouling Make machine disinfection Check valve damaged Replace the check valve installed on the permeate line before max Pressure switch install a manometer on permeate line and check water pressure on permeate line Water leakage Check the permeate hydraulic circuit for leakages install a manometer on permeate line an
28. res water the machine starts to produce permeate water pushing the key ENTER gt the conductivity is displayed When the dishwasher stops water requirement the board returns in stand by mode If after 50 seconds from pump start the conductivity is over 70 uiS cm the display High Cond c a 235 ea Low pressure alarm Alarm P min Leakage alarm Alarm Leakage shows High cond for high conductivity alarm After four consecutive high cond alarms the machine also makes three beeps after 50 seconds from operative start if high cond alarm occurs High cond alarm is only a visual and acustic alarm machine continues to work When pump is on if low pressure failure occurs the display shows Alarm P min and the board makes a beep The machine restarts automatically after 1 minute If consecutive low pressure alarm occurs the restart delay automatically increases To restart the machine immediately turn OFF and ON with the The min pressure alarm is ignored during the first 20 seconds from operative start If water leakage alarm occurs the machine stops and makes a continuous beep displaying Alarm Leakage BA UO compact engl doc o m SS ee VV CITC Filter change Alarm Filter Change To restart the machine turn OFF and ON with the The filter has a lifetime of 140hours of work Once reached this limit the board shows Filter Change Replace the cartridge an
29. see nnns 19 6 6 POWER CABLE REPLACEMENT ele ues Ur ux uva pe ve ee ge ege eese ege EE NE EVE 20 6 7 MACHINE SANITATION ciere Jade eit ho ne Gadde deele geed 21 6 8 FREEZE PREVENTION TREATMENT 21 6 9 VERIFICATIONZCALIBRATION OF THE SETTING rere ee ntn trn nono E nies ove ntn Nee 22 6 10 CLEANING CONDUCTIVITY PROBE 5 2 2 sn nnns 23 6 11 ELECTRONIC BOARD EXTRAORDINARY MAINTENANCE HH He Hehe ehe ene enne 24 7 IiUZRIleulicm 25 ATTACHMENT I CE DECLARATION SOS 29 ATTACHMENT II SPARE PARTS UO COMPACT 150 31 ATTACHMENT Ill CE LABEL 32 ATTACHMENT IV MAINTENANCE ennenen nnne 33 BA UO compact_engl doc rV m AW CITC 1 GENERAL INFORMATIONS 1 1 MANUFACTURER ASSISTANCE BUILDER ASSISTENCE EVO WATER oHG Falkenstr 2 Personal Data of the Retail Seller Westerheim 72589 Germany 1 2 CERTIFICATION UO COMPACT 150 was manufactured in compliance with the following EU Directives Machines 2006 42 EC Low Voltage 2006 95 EC Electromagnetic Compliance 2004 108 EC Household and similar electrical appliances Safety Part 1 General requirements EC EN60335 1 2004 The machine also comes equip
30. tante responsabilidade na redu o do lixo preparando a reciclagem dos instrumentos el ctrico electr nicos A reciclagem previne a dispers o de materiais perigosos nos lixos minicipais s mbolo da barra no barril lembra ao utilizador de jogar este producto como um lixo municipal nao classificado D Richtlinie 2002 96 EC wird diese Produkt als elektrisches elektronisches Ger t eingestuft Dieses Ger t nicht als nicht klassifizierten Stadtm ll beseitigen Diese Ger t an eine daf r vorgesehene Sammelstelle bringen gem den vorortigen und auf nationalem Gebiet geltenden Gesetzesbestimmungen Der Verbraucher kann betr chtlich dazu beitragen den Abfall zu verringern indem er ein Recycling der elektrischen elektronischen Ger te vorsieht 2 m VV CCC Ein Recycling verhindert dass gef hrliches Material im allgemeinen Stadtm ll beseitigt wird Das Symbol mit ausgestrichener Tonne soll bedeuten dass das damit gekennzeichnete Produkt nicht als nicht klassifizierter Stadtm ll zu beseitigen ist ES La directiva 2002 96 EC clasifica este producto como un aparato el ctrico electr nico No tire este aparato como si fuera un residuo municipal no clasificado Tire este aparato en un centro de recogida o de reciclaje seg n la ley local o nacional El consumador cumple un papel importante en la reducci n de la eliminaci n de residuos predisponiendo el reciclaje de los aparatos el ctricos
31. te the flushing mode every 1 hour This process consists of the substitution of stagnate water with fresh water inside the membrane During this operation the solenoid valve will open for 1 minute The amount of drained water depends on inlet pressure and is approx 2 liters 4 3 MANUAL BYPASS In chase of problems with the osmosis machine it is possible to bypass the internal equipment turning the bypass valve from OPEN position to BY PASS position and supplying softened water to outlet Ls If manual valve is turned to by pass position disconnect the power plug BA UO compact_engl doc re Vi m rum 4 A ELECTRONIC BOARD FUNCTIONING ELECTRONIC BOARD FUNCTION KEYS Key ENTER allows to enter program pages and parameter confirm Key allows to scroll program pages and to increase the selected value Key allows to scroll program pages and to decrease the selected value Key ON OFF allows to set the board in sleep mode WARNING The electronic board is already programmed for correct functioning of the product The instaler and the user can modify program parameters interval between maintenances the modify of these parameters is up to the installer user in this chase The producer declines any responsibility of the correct functioning of the machine 4 GC Normal functioning EVO WATER When the board is in stand by mode the name of the installer is displayed When the dishwasher requi
32. ull the cartridge form the head Install the new cartridge and turn counter clockwise 90 Dry with a clean any water Close the cover Insert power plug and make filter reset on the electronic board Ke 5 1 FILTER REPLACEMENT To replace external prefilter follow these steps Remove the power plug ATTENTION Use only original parts EVOWATER BA UO compact engl doc a m Wassertechnische Systeme Wa te To load the salt follow these steps 1 Pull the two locks of the top cover 2 Turn the cartridge 90 clockwise until the head assembly is in closed position ts 3 Pull the cartridge form the head 4 Install the new cartridge and turn counter clockwise 90 5 Dry with a clean any water 6 Close the cover 5 2 SOFTENER SALT REFILL A Remove the power plug BA UO compact_engl doc rV SS ee VV CITC 6 PROFESSIONAL EXTRAORDINARY MAINTENANCE ATTENTION The internal UO COMPACT 150 electrical apparatus is fed by 230 Volts electrical N current Before opening the machine make sure the machine is unplugged 6 1 REQUIRED TRAINING FOR MAINTENANCE PERSONNEL Maintenance personnel must possess the following qualifications as prescribed in this manual e adequate knowledge of standard EU approved safety procedures required technical knowledge to understand the concepts outlined in this manual e Knowledge of basi
33. y cable must be compatible with the device as indicated on the required Se tags and labels affixed to the rear of the machine The electrical cable of the circuit must not be less than 1 mm in diameter The voltage of the device must comply with the standards of the local area or country power surges must be limited to no more than 10 9 m 1 Inlet water connection Outlet water connection Manual bypass valve Drain softener Air vent Drain Electronic board Filter cartridge Joo WARNING Im Before water inlet a water safety device in compliance with EN1717 must be installed BA UO compact engl doc lt AW CITC 3 1 DRAIN BRACKET TYPICAL INSTALLATION Install the drain bracket on the 40mm diam sink drain siphon Check that the seal rests properly on the pipe and the bolts are tight Remove the nut of the drain By using a 4 mm drill bit drill a hole in the exhaust pipe of the siphon at the nut just disassembled Insert the drain pipe into the nut for about 2 cm and tighten the nut on the bracket Tighten the nut and install the valve with the arrow pointing towards the bracket as close as possible to the drain AVN drain tube non return valve Drain pipe fixing nut Drain bracket Seal Nut Fixing bolt nut
Download Pdf Manuals
Related Search