Product manual
Contents
1. MICROSCOPE USER MANUAL For MS002 MS006 MS007 MS008 MS020 MS112 MS601 MS701 MS901 MS903 MS907 MS908 MS911 MS916 MS925 INTRODUCTION TO A MICROSCOPIC WORLD In this world there are an abundance of living things Some are large and easily seen with our own eyes but others are so minute that millions could be placed on the head of a pin These can only be seen through a microscope The microscope was invented many years ago and since then has opened a field of research as fascinating and beautiful as anything you can imagine Now all science from the most elementary study of biology to the highly specialised fields of astro physiology use some form of microscope to enable the students of these sciences to better understand the intricate complicated forms of living organisms or static materials that make up this world in which we live Your microscope will be a source of many hours of pleasure as a hobby or open the door to advanced knowledge in the varied fields of science We hope you enjoy your experience BATTERY INSTALLATION 1 Unscrew the lamp cover with a screwdriver to take off Dos WATTS per 2 Insert 1 CR2032 battery into the battery compartment carefully the correct and positions 3 Replace the lamp cover and screw it back into place FOR ADJUSTABLE ZOOM MODELS The figure 12X or 18X is indicated on the opposite side of the eyepiece tube By rotating2. Using the focusing knob lower the lens as close as possible to the prepared slide without actually making contact Then while looking through the eyepiece turn the knob in the opposite direction until the image comes into focus 7 When the room is dark with low intensity of natural or lamp light or when the sight is not clear at a high magnification turn the reflector Then the light source lights automatically to enable observation 8 The light source lamp is used with 1 CR2032 battery put in the illuminator lamp ADVICE FOR SUPERVISING ADULTS a Read and follow the instructions and safety rules Keep them for reference b This Microscope set is for use only by children over 8 years old c Because children s abilities vary so much even within age groups supervising adults should exercise discretion as to which preparations are suitable and safe for them The instructions should enable supervisors to assess any preparation to establish its suitability for a particular child d The supervising adult should discuss the warnings and safety information with the children before commencing the preparations Particular attention should be paid to the functionally sharp point on the needle and the functionally sharp edges on the scalpel and slicer SAFETY RULES a Do read these instruction before use follow them and keep them for reference b Do keep young children and animals and those who are not wearing eye prot
3. the silver knurled ring in counter clockwise direction the eyepiece power will zoom to 18X Assuming that you are using an objective turret of 12X and with the eyepiece at 12X then the magnification power of the combination is 12x12 144 The object you see is enlarged 144 times l l o Zoom Eyepiece By just using the zoom eyepiece and rotating it to 18X 12x 18x you now have a combination of 12x18 216 INTRODUCTION OF MICROSCOPE Eyepiece Focusing Knob Body Tube Revolving Turret Objective Lens Eyepiece 1 2 3 4 5 6 Arm 7 8 g 1 1 2 Focusing Knob 3 Body Tube 4 Revolving Turret 5 Objective Lens 6 Arm 7 8 9 1 Stage Clip Mirror Stage Clip Mirror 0 Illuminator Lamp 0 Illuminator Lamp Light Source Lamp Light Source Lamp 11 Base 11 Base D Ref MS002 MS007 MS601 MS903 MS907 MS908 MS911 MS916 MS925 Ref MS701 1 Eyepiece 1 Eyepiece 2 Focusing Knob 2 Focusing Knob 3 Body Tube 3 Body Tube 4 Revolving Turret 4 Revolving Turret 5 Objective Lens 5 Objective Lens 6 Arm 4 f i fa Plage 8 Mirror 8 Clip 9 Illuminator Lamp 9 Mirror O 10 Base 10 Illuminator Lamp om Light Source Lamp Light Source Lamp 11 Viewer 11 Base 12 Viewer Microscope Knob Ref MS020 MS901 Ref MS008 1 Eyepiece 2 Focusing Knob 3 Body Tube 4 Revolving Turret 5 Objective Lens 6 Arm 7
4. Stage 8 Clip 9 Mirror 10 Illuminator Lamp Light Source Lamp 11 Base Ref MS006 MS112 HOW TO USE AS A PROJECTION DEVICE Remove the eyepiece and tilt the microscope so that the body tube is pointing at a white surface not more than one meter away For best results view in a darkened room HOW TO MAKE A PREPARED SLIDE If the given sample is not thin and transparent it cannot be observed by the microscope as the light from the reflector or the light source does not pass through it Fibres pollen wool or salt will be easy to observe and do not need a cover glass Clear samples are stain first with a drop or two drops of methylene blue Eosin or other dyeing solutions available on the market Note These are dyeing solutions and therefore could cause staining of clothing carpets and fabrics Special care should be taken when handling these solutions 1 Temporary mount Wipe the slide and cover glass clean Thin the 4 sample with a razor blade Note The blade is very sharp so handle with extreme caution or similar then pick it up with tweezers and put it on the centre part of the glass slide Put one drop of water on the sample with a dissecting needle or if the sample is clear use on drop of the above mentioned dyeing solutions Note The needle has a sharp point so handle with extreme caution and then gently put the cover glass on it taking care not to trap any air bubbles Remove any excess water or dyeing so
5. ection away from the experimental area c Do always wear eye protection d Do store microscope sets out of reach of young children e Do clean all equipment aftr use f Do wash hands after carrying out preparations g Do not use any equipment which has not been supplied with the set h Do not eat drink or smoke in the experimental area j CAUTION FOR HANDLING 1 The vital part of the microscope is the lens Therefore sufficient care must be taken in handling the lens Do not put foodstuffs in original container Dispose of immediately Do make sure that all containers are fully closed and properly stored after use 2 If the lens gets dirty or dusty wipe the lens surface with a clean lens tissue or soft cotton cloth Do not rub the lens with a finger or dirty cloth etc 3 After it is used put a cover on the microscope or put it back into the box for screening from dust 4 Microscope should be stored in a moisture free place Moisture build up on the light causes a reduction in light intensity 5 When a microscope is not used for a long period of time remove the light source battery 5 P38 MS911 81021000
6. lution with blotting paper Now it is ready for observation Remember to wash your hands after doing the preparation and remember to dispose the dyeing solutions 2 Permanent mount Wipe the slide and cover glass clean as above Temporary mount Proceed as above but before covering the slide with the cover glass add a few drops of gum media or Canada balsam solution or transparent adhesive glue with a dissecting needle to the slide Push down on the cover glass with tweezers or the like to fix it in place and leave to dry for about a day HOW TO USE THE MICRO SLICER Put the specimen which you want to cut for study into the holes of the micro slicer Note the mico slicer contains a sharp edge so handle with extreme caution Revolve the blade Then you can get thin slices of the specimen A INSTRUCTIONS FOR USE OF MICROSCOPE 1 First tilt the arm and adjust the position of the reflector so that the light is fully caught by the mirror 2 When the light is fully reflected by the mirror as can be seen through the eyepiece the microscope will be ready for observation 3 Next put the prepared slide on the stage and fix it in place with the clips 4 Now decide what magnification to use The greater the length of the objective lens the greater the magnification Observation is generally made Starting at a low setting 5 In order to change the magnification turn the revolving turret until you feel a click 6
Download Pdf Manuals
Related Search