GSM module G10C
Contents
1. Leave blank if only Test SMS reporting required APN User Protocol Password DH51 1195 22 175 1 34 176 32 129 Encryption key Return to primary after E al attempts Backup reporting after Module events Contact ID event code Contact ID restore code E 700 33 999 E 602 59 999 E 302 99 999 E 130 33 001 E 130 33 002 E 130 33 003 FAA riri aa R 00 33 999 R 302 99 333 R 130 33 001 F130 33 002 F130 93 003 mA A Aa Dey GIOC SH OOO06 Ver 1 35 Connected Primary reporting The section is for setting a primary communication channel through which the module will transmit messages to an alarm receiving centre ARC If GPRS is selected IP1 address or domain name of ARC and a port number of the server must be specified in the corresponding boxes Server IP1 address or Domain and Port If DATA is selected enter telephone number of PSTN line receiver of ARC in the box Tel 1 to which module will dial messages in DTMF tones The telephone number must be entered with international country code without the plus sign If SMS is selected enter telephone number of the SMS receiver of ARC in the box Tel 1 to which module will send with SMS messages The telephone number must be entered with international country code without the olus sign Backup reporting The section is for setting a backup communication channel through which the module will transmit messages if connection through2. E 602 E 602 Periodic Test Periodic test report E R 120 Panic Alarm Duress Alarm Burglary Alarm Burglary Alarm restore AC Loss AC Loss restore E R 130 144 E R 301 E R 302 309 E R 321 E R 351 S497
3. any value must be entered just leave ssacePSW space N SMS I I x r uha Enter the word ENCR enter the 6 digit messages decrypting key which is aa K Set in IP receiver default is 123456 U U Order of actions after the message is sent 1 Open the window of software IPcom and select the object ID which operating parameters of transmitting module should be changed To select right click on the ID number Open the configuration program G10config Left click on the icon G10config has been appeared beside the selected ID number Click on the button Connect in the opened program G10config tool bar GPRS connection status Connected must be indicated in the program s status bar Click the button Read F7 on old configuration to be displayed Further actions are identical as when the module is connected to a computer with a USB cable Just set the desirable values of module operating parameters in the opened program G10config windows After entering desirable values click the button Write F6 on the values to be set in the module G10 Just close the program G10config and GPRS communication session closes too ID xi Fie Settings About r Control Object state summan Refresh contrat i Wasting for GPRS 1 s m Refresh Depo Waiting for SMS Refresh every seconds pt Simian Lost 0 r Obyects control _ Remove object Object ID IP Phone number Communication state Level GPRS last
4. lt E lt COM lt COM lt IN lt IN a PGM 2 Cn lt IN2 lt IN2 PSM3 Q lt N3 vya lt IN3 Seo ee lt IN4 Soo Ne lt OUTI lt OUT Sg cue lt COM 8 s lt COM amp PGMS ES owt oo I gt 5 G gt gt z G o G 5 5 lt 9 lt N N G10C G10C Controlled device Controlled device Valdomas prietaisas Valdomas prietaisas Ynpasnaemoe ycTpo CTBO Ynpasnaemoe YCTPONCTBO Fig 1 General wiring diagram for connection to the security control Fig 2 General wiring diagram when activatable input status panel when constant input status control mode 24 h is set control mode Control panel is set Setting operating parameters Module G10C operating parameters are set with computer program G10config Program can be found in website www trikdis It 1 Connect the module G10C with a computer using a USB cable Note USB drivers must be installed in the computer If the module is connected to a computer for the first time MS Windows OS should open a Found New Hardware Wizard window for installing USB drivers Download the USB driver file USB_COM inf for MS Windows OS from the website www trikdis lt In the wizard window select the function Yes this time only and press the button Next When a new window Please choose your search and installation option will open press the button Browse and select the place where the file USB_COM inf was saved Follow the remaining wizard instructi
5. ping GPRS ping interval GSM last ping Gconfig A Waning ior GPRS message g 2010 03 23 1513 31 0 MA Firmware version upgrading remotely Connect the module G10C with the program G10config remotely See previous chapter how to connect remotely 1 2 3 4 Open the program G10config See previous chapter how to open the configuration program Press the button Connect To read the parameters set in the module press the button Read Open the window Firmware and with clicking on the button Browse select the latest version of the firmware file Press the button Start Wait until the firmware will be written into the module processor memory This may take 1 3 minutes after which the module will reconnect to the program G10config Set the module operating parameters in the same way as described while connected via USB port s10 Remote control of the module In order to change the status of output OUT1 send an SMS message to module SIM card number Examples of SMS messages are given in the table Notes Ifthe table Wireless programming phones is empty the module will change its output status after receiving an SMS message from any phone If telephone numbers are entered into this table module output status can be changed only from these phones Output status can be changed when the operating mode for output OUT1 is set to Remote PGM control SMS SMS message should be written in capital letters only
6. tape 10 cm 1 pc Note GSM antennas of desired type are collected by the additional request gt 11 ANNEX 1 Non alarm events transmitted to ARC Pp s a ae Activated Device TEST message E 602 Time is specified yes no Connection with the security panel lost restored E 700 Not specified E 702 PING signal through SMS channel E 750 Connection by SMS channel E751 lost restored PING signal through GPRS channel E 760 Connection by GPRS channel E 761 lost restored PING signal dialled in DTMF tones E 770 E 144 99 999 R 144 99 999 ANNEX2 Texts of SMS messages which are sent to mobile phone after occurring particular event 1 NC input Input mode Activated restored P Control panel Sent CID code E R 100 E 100 R 100 E 110 Existing MEDICAL PANIC ALARM FIRE PANIC ALARM In CID standard Medical Alarm Fire Alarm E R 110 115 R 100 E 120 PANIC ALARM R 120 E121 DURESS ALARM E 130 ALARM R130 Alarm restore E 301 R 301 E 302 Low System battery R 302 Low system Battery restore E 321 Bell trouble on control panel Bell 1 R321 Bell trouble restore on control panel Bell 1 restore E 351 Phone Line trouble on control panel Telco 1 fault R351 Phone Line trouble restored on control panel Telco 1 fault restore E R 400 401 E 401 OPEN by Open by user 406 451 R 401 CLOSE by Close by user E 4 ick DISARM ick DISARM E R408 08 Quic S Quic S R 408 Quick ARM Quick ARM
7. 99 999 Classificator POWER E 302 99 999 R 302 99 999 Event fi 30 IN1 E 130 99 001 R 130 99 001 Subgroip Bs IN2 E 13099 002 R 130 99 002 IN3 E 130 99 003 R 130 99 003 Siu oor IN4 E 13099 004 R 130 33 004 IN5 E 13099 005 R 130 99 005 Module events Default E event description Default R event description TIME Internal clock of the module is not set Internal clock of the module is set U TEST Periodic module Test message POWER Power supply voltage is lower than 11 5 V R IN Input INI external circuit is disturbed Input N1 external circuit has restored U Z Z Z E IN2 Input IN2 external circuit is disturbed Input N2 external circuit has restored Z Z Z Z 7 IN3 Input IN3 external circuit is disturbed Input N3 external circuit has restored U Z Z Z o IN4 Input IN4 external circuit is disturbed Input N4 external circuit has restored U oZ Z INS Input MCI external circuit is disturbed In the directory Text SMS to user enter the parameters which are necessary to send SMS messages to users Main iba oporana Name m 2 e IRE Na Telephone Text SM reporting Alarm Restore ID ID T1 37012312345 Settings Open Close MM OOD T2 4512312345645 Firmware Troubles Momo T3 4412312345678 Tests v D D mM T4 4112312345678 International phone number Example 37068012345 SMS encoding fi ENGLISH WIN1252 gt Send SMS Described Only gt ObjectID Account Name Users
8. EC Gal Dal giW6le uu uuu uu u n uu m muu umu umu m ata uha 11 PAC Ka SOC Ori r GBlS uu u 2 asas sha a hasa mpSqa mua Qs aaa mapasa asqa uuu a a s ua 11 ANNEX 1 Non alarm events transmitted to ARGC uu uu u Sma aa a akaqa eq aaa aqp aspa a Ass 12 ANNEX2 Texts of SMS messages which are sent to mobile phone after occurring particular event 12 Safety requirements Please read this manual carefully before using the security module G10C Security module G10C should be installed and maintained by qualified personnel having specific knowledge regarding the functioning of GSM devices and safety requirements Module G10C should be mounted in places with restricted access and in safe distance from any sensitive electronic equipment The device is not resistant to mechanical effects dampness and hazardous chemical environment Liability restrictions When buying the Device the Buyer agrees that the Device is a part of a security system of premises which sends messages about security system status The Device when installed does not diminish the probability of burglary fire intrusion or other breach of premises UAB TRIKDIS is not responsible for burglary fire or any other breach of Buyer s and or User s premises and is not liable for any direct or indirect damages incurred thereof When buying the Device the Buyer agrees that the Device supplied by UAB TRIKDIS fully meets his requir
9. WTRIKDIS pe e k A TRKDIS GKN Network Dota Power GSM module G10C v 1 3X Installation manual JSC UAB TRIKDIS Draugyst s str 17 LT 51229 Kaunas LITHUANIA E mail info trikdis It Webpage www trikdis t Table of contents See ey r6 ulremeni Su uu xuma uuu au niaaa pe sues veuceuuacnacdee annseucamosedirscessuusucanscuienesteutwaueecdey semskuueae 2 ELAM reS CUIOMS uuu on a 2 GSI Maie 10C u uuu soxcenushan iden sotenectobedued son a on caey saskcubeaenaduet saa ahusta oh apas baku a Dasa 3 DESEMPLION OF module oOp eral i0ofzuy n uu u hu aS Da a Su aD SW p uhuy Sa ua h od esususessQuiue 3 Mogu le Componente sirere u Aa recto sacaehvcieade duseaenseuiea acuta ease gad anauteeenapteuienedacue aoestenluead nests aeqeeueenadene nese ueaa pallet amentiaaeess 3 Module instalation Steps eee Re tet A ere ee 4 SELUINE perane par ie ler a valcws houeunas geese vansuaasteueswins Nosoua ane eaten aiioyoraaauendune eeu aunaneaeoeunsueyoraantenderep ney nanneaesee 5 Updating mod le firmware VELSlOMN iccetssaiccsccsareete un S Quan i SQ iS i Quwaq h kau 9 Seti SECOnBHHSuraltiorniremotelyu y u a a aD u a aku aya aus huqawap ay qapa Ayam akaqa ay aD aa ad yaya 9 Firmware version upgrading remotely 10 Remote controlo thiemod leuuu e uuu Q u a ua N Saa cau aa aya A 11 F
10. Zones 001 UserName 1 Zz 001 Zone 1 Pe 002 UserName 2 002 Zone 2 012 UserName 12 009 Zone 3 064 UserName 64 032 Zone 32 Partitions 01 Areal 02 Area2 06 Areab Telephone Telephone numbers of the users should be entered in fields T1 T2 T3 T4 to which SMS messages will be sent The telephone number should be entered with international country code but without the plus sign Name Choose by selecting the check boxes about which events messages will be sent to users Alarm Restore SMS messages will be sent when an input circuit is disturbed which events are described in the table Module events with E 1xx xx xxx and R 1xx xx xxx codes security system alarm fire burglary trespass assault and etc Open Close SMS messages will be sent when an input circuit is disturbed which events are described in the table Module events with E 4xx xx xxx and R 4xx xx xxx codes security system arm disarm Troubles SMS messages will be sent when an input circuit is disturbed which events are described in the table Module events with E 3xx xx xxx and R 3xx xx xxx codes security system troubles Tests SMS messages will be sent when an input circuit is disturbed which events are described in the table Module events with E 6xx xx xxx code security system Test messages SMS encoding Choose in the list the preferred encoding for the text in SMS messages Send SMS When All is chosen SMS messages will be sent t
11. ding PGM GPRS PING time CSD PING time SMS PING time Test time Disconnect FFS GPRS reporting Text SMS reporting B x Open Fa Save F5 Iv Hex Read F7 Open Last F4 Write Fb 1111 1111 1234 4 digits 1234 4 digits Account name SIM Card FIN GPRS ping time User code CSO ping time min Admin code Bl Shoe tie mn z Test tine JJJ Panel type 1 24h NC Ir Input mode PGM Remote control SMS Y Save access code Read after connection Restore defaults settings Restore F11 SH 000067 Ver 1 35 Connected Section for entering a 4 digit object identification code Section for entering the SIM card PIN code Leave this field blank if PIN code request is disabled Section for entering a user code When connected using a User code only those module parameters can be changed which change was allowed by the administrator Section for entering an administrator code When connected using an Administrator code all module parameters can be changed and also access to parameter change can be restricted for persons connecting with the User code Select in the list the operating mode of the module G10C according to which the status of module inputs which are connected to the security control panel PGM outputs is controlled If 24h is selected input status will be constantly controlled If Control Panel is selected you will be able to turn
12. e is selected input MCI operates as an input status controller While input MCI is connected with COM disturbances in the circuits of inputs N1 N4 are allowed and reports about them are not created After the circuit of input MCI is broken the module will send a report informing that input status is controlled and disturbances in the circuits of inputs N1 N4 are no longer allowed When input status is controlled by input MCI and circuits of the inputs N1 N4 are disturbed the module will send reports about these disturbances restorations Module G10C has five inputs When operating in 24 h mode module MCI input is the fifth NC type input and when operating in mode Control panel it operates as a controller for the other four inputs The module can send messages about the disturbances normalisations of input N1 N4 and MCI external circuits to the monitoring station through a specified connection channel If the message transmission through this channel fails the module may send them through a backup channel When two server IP addresses are set and the module loses connection with both of them it can send information to the monitoring station with SMS messages The module can periodically send signals PING for connection control The reports can be sent with SMS messages up to four mobile phones A user friendly SMS message text can be assigned for every module input event Module output OUT1 status will change when connection with
13. ements for intended use UAB TRIKIDIS provides no guarantees that the Device shall function as declared if the Device is installed and used not according to its original purpose user manual and relevant electronic and technical conditions UAB TRIKDIS is in no way associated with GSM GPRS Internet service providers operators thus UAB TRIKDIS is in no way responsible for any defects in Device operation if they have occurred because of the loss of GSM GPRS Internet connection or because of other defects in the service provider network UAB TRIKDIS has no control and is not responsible for the prices and marketing of network services provided by the GSM GPRS Internet service providers UAB TRIKDIS is not responsible if GSM GPRS Internet services are not provided to the Buyer and or User of the Device or were cancelled and any direct or indirect damages were incurred thereof UAB TRIKDIS is not responsible for any direct or indirect damages incurred by the Buyer and or User of the Device due to loss of electricity UAB TRIKDIS is not liable if Device firmware versions were not updated by the Buyer and or the User on time User manual of the Device can contain technical inaccuracies grammatical or typographical errors UAB TRIKDIS reserves the right to correct update and or change information in the installation manual GSM module G10C Module G10C is designed for transmitti
14. fter the section the duration of time for sending messages though the backup communication channel when connection through the primary channel has failed Backup reporting Used if both the primary and backup channels are selected for connection with the monitoring station Enter in after the section the number of attempts to transmit information through the primary communication channel after which the module will connect to the backup communication channel Monitoring station administrator should provide the IP addresses port and telephone numbers encryption protocol and key with other parameters necessary for connecting with the monitoring station APN Access point name for connecting to the GSM operator s network User User name for connecting to the GSM network Login Password Password for connecting to the GSM network DNS1 DNS2 Leave the default values in the sections APN user name and password should be provided by the GSM network administrator from which you have received the SIM card Module events Events are given in the table about which the module will also send messages Event code can be changed by double clicking the cells Contact ID event code or Contact ID restore code and by entering exact values in the newly opened window After entering the values press the button OK Module events x Ewent Contact ID event code Contact ID restore code Active TIME E 70099 999 R 700 33 333 T TEST E 602
15. ller is functioning status functioning of Yellowflashing l Power supply is not sufficient lt 11 5 V microcontroller is microcontroller and functioning Programming status Green and yellow flashing in turn Programming mode O j Module installation steps a Actions T Notes 1 Set the operating parameters for the module Follow recommendations in chapter Setting operating i parameters 2 Insert an active SIM card re x Contact a GSM service provider regarding the SIM card We i i do not recommend using pay as you go prepaid SIM cards 3 Fasten the module to the security control panel The location and dimensions of holes to be drilled in the metal casing by using either M3x6 screws or casing for fastening the module and antenna adhesive fastening tape 5 Connect the module to the security control panel according to the wiring diagrams given below E Tin i lo E S se unas a E ET 7 Check GSM signal strength according to ight Sufficient GSM signal strength is level 5 five yellow flashes of indication x indicator Network If GSM signal strength is not sufficient Ln use other antenna type I UU aa l 8 Check if the module sends messages according to j The message must be sent and received at the specified IP its configuration address If messages are sent to a mobile phone check if all nian SMS messages are received U U Ua Wiring diagrams lt E
16. ng security system messages to a monitoring station through a GSM connection Module features Messages to the monitoring station can be transmitted in on of following modes or through GPRS connection or with SMS messages or in DTMF tones Messages can be sent through a primary communication channel and if it fails through a backup channel Even if GPRS connection with two servers is lost information can be sent with SMS messages Sent messages correspond with Contact ID protocol codes The module can send SMS messages to 4 user mobile phones Input status can be controlled constantly or when control is activated Output OUT1 status can be controlled remotely Operating parameters and firmware version can be updated remotely Operating parameters are set with the program G10config Description of module operation Module G10C is connected to security control panel PGM outputs and can be set to operate in one of the two modes a Constant input control mode 24 h After the security control panel has changed the state of its PGM output module input circuit is also disturbed The module G10C immediately sends a report about this event to the monitoring station When the security control panel restores its PGM output status the status of module input external circuit is also restored The module will send a report about this event A general wiring diagram is given in Fig 1 b Activated input control mode Control panel When this mod
17. ns Updating module firmware version When the manufacturer adds new features to the module G10C firmware of the previously bought module can be updated 1 Download the latest G10C_vx xxx prg update file from the website www trikdis t 2 Connect the module G10C to a computer and start the program G10config Open directory Firmware update and select the file G10C_vx xxx prg saved in the computer 3 Press the button Start F9 Wait until file uploading bar Progress is full and then press the button Disconnect F8 Unplug the USB cable 4 Plug the USB cable back in Firmware update process may take 60 90 seconds Wait until indicator Data will stop flashing green and press the buttons Connect F2 and Read F7 The new version of the module firmware will be displayed in G10config program status bar Setting of configuration remotely In order to set module G10C operating parameters remotely a SMS message with the particular syntax must be sent by GSM number of SIM card put in the module G10C When the module G10C receives this SMS message it opens GPRS communication session with software Pcom Wireless programming phones If during the previous setting module operating parameters were being entered GSM number of authorised person in the list G10config Settings Wireless T01 programming phones the module G10C will open GPRS communication session if it ins receives SMS message with particular syntax from authorized person s ph
18. o users about all module external circuit events When Described Only is chosen SMS messages will be sent to users only about those external circuit events which are described Object ID Enter the object name It will be included in the message sent to user T Users Function is not used Zones Entries in the table are associated with PGM output events controlled by the security control panel When a connected module input circuit is alarmed restored its description entered in the table will be included in the SMS message Partitions 1 If the security system is divided into several individually protected areas and 2 if control panel PGM output events shall mark events in these areas then entries in the table are associated with these events If a connected module input circuit is alarmed restored the name of the partition entered in the table will be included in the SMS message 6 Press the button Save F6 and values entered in the program Gi10config windows will be uploaded to the module G10C 7 Press the button Disconnect F8 and unplug the USB cable from the USB socket Save F5 By pressing this button values entered to the program Gi10config can be saved in the computer A new file with extension gst will be created It can be used later as a template for configuring other modules Restore F11 Button for restoring default factory operating parameters of the module G10C Press the button Yes when request window ope
19. one TO4 SMS message text structure Word space Means space between SMS text symbols CONNECT 5pacel234spaceSERVER 100 100 100 100 ePORT 1000 eAPN provider ace USR NaMe spacePSW PSWepaceE NCR enc Note entering values use capital letters Description of syntax _ CONNECT Enter the word CONNECT means starting command Enter your 4 digit access code to module parameter configuration default is 9874 was 21234 UU Ua x Enter the word SERVER enter IP address of the IP receiver from which SERVER value I ee Module operating parameters will be configured 1 U U a x Enter the word PORT enter port of the receiver from which module PORT value K Operating parameters will be configured U U a x Enter the word APN enter the GPRS access point name of network where APN value SIM card is operating If GSM service provider doesn t require any value must uasssssssssssssssssusssssususssssisssssui Pe entered just leave spaseAPN space in SMS U U x Enter the word USR enter the User name of GPRS access point name of USR value network where SIM card is operating If GSM service provider doesn t require eee erences any value must be entered just leave spaceUSR spacer IN SMS U U l x Enter the word PSW enter the Password of GPRS access point name of PSW value network where SIM card is operating If GSM service provider doesn t require G
20. ons to finish the USB driver installation 2 Start the program G10config 3 Select the program directory Settings Port com xl In the drop down list Port select the port to which the module is connected Language English j Note specific port to which the device is connected will appear only when the device is properly connected In the drop down list Language select the desired program language 4 Pressthe button Connect Disconnect F2 F8 When the module G10C is connected to a computer File About module LED Power indicator should flash green and yellow in turn Program G10config status bar should indicate connection status Connected and display the following information about the connected module 2 GPRS reporting Text SMS reporting i Firmware SN 000174 Module serial number Yer 1 33 Firmware version installed in the module 5 Press the button Read F7 x When the window Access code opens enter the access code default access code is 1234 and press the button OK If you want for the program to remember your access code check the box Remember Then the Access code window will not open when connecting to the module for the next time Remember Select the program directory Main and set the following parameters Gi0config File About Settings i Firmware Dey G1IOC Object ID SIM Card PIN code User code Admin code Operates with control panel IN1 PGM Start sen
21. the input control on or off Function is not used If the option Remote control SMS is selected in the drop down list the module will change its output state after receiving an SMS message containing a control command See chapter Remote control of the module If the option Lost Primary channel is selected output state will change to the opposite after losing communication through the primary channel When the option Lost Secondary channel is selected output state will change to the opposite after losing communication through the backup channel If the option Lost Both channels is selected output state will change to the opposite after losing communication through the primary and backup channels Function is not used Time interval according to which the module will send messages for GPRS connection control to the monitoring station Function is not used Time interval according to which the module will send SMS messages to the monitoring station to check the connection Time interval according to which the module will send Test connection control message to the monitoring station In the directory GPRS enter the parameters for connection with the monitoring station x File About Disconnect F2 F 8 Read F7 Open Last F4 Write FE Open F3 Save F5 Primary reporting Backup reporting Server IPI address ji 9514 186714 Server IP2 address or Domain h or Domain Part 55000 Fort Tel 1
22. the monitoring station server has been lost restored or when the module has received an SMS message changing its output status Module components Terminal block SIM card holder USB socket GSM antenna Indicator Network Indicator Data Indicator Power ee ee eS L ss Terminal block description Contact Description O O _ O te HIN power supply clamp U 2 I COM I Common clamp O O O O IM ___Istinputclamp NCtype O O O O I IN _ 2nd input clamp NC type 22 2 0 INS __3rdinputclamp NCtype UU 2 I IM Ath input clamp NC type OU C C 2 O OUTE Output clamp OC type U U 0 f COM o I Commonclamp O g I MII L Sth input programmable NC type 0 0 ED Operation Descriptio a Network presents connection GrenON U Module is connected to a GSM network U with GSM network status YelowON oZ 00 Message is being sent 0 0 0 Green flashing o Connecting to GSM network III E f Yellow flashing U i Number of yellow flashes represent GSM signal strength l Data presents data exchange GreenON ___Unsent messages present in module memory U x I RedON Unableto be sent messages U U Green flashing Messages are being received from the control panel U Red flashing rapidly ___Module configuration is incorrect U U I UU f Red flashing SIM card error I Power presents power supply Green flashing I Power supply is sufficient microcontro
23. the primary communication channel has been lost If GPRS is selected IP2 address or domain name of ARC and a port number of the server must be specified in the corresponding boxes Server IP2 address or Domain and Port If DATA is selected enter telephone number of PSTN line receiver of ARC in the box Tel 2 to which module will dial messages in DTMF tones The telephone number must be entered with international country code without the plus sign If SMS is selected enter telephone number of the SMS receiver of ARC in the box Tel 2 to which module will send with SMS messages The telephone number must be entered with international country code without the olus sign Second backup Telephone number of the monitoring station to which SMS messages will be sent when the module has lost reporting tel GPRS connection with both servers This option is allowed when both the primary and the backup connection channels are selected as GPRS The telephone number should be entered with international country code but without the plus sign Protocol Drop down list for selecting a protocol for encrypting messages Encryption key Section for entering a 6 digit key for encrypting messages sent to the monitoring station The password must be same as the password entered in a server program Pcom Return to primary Used if both the primary and backup channels are selected for connection with the monitoring station Enter in a
24. w TF a a a a aaa a a aa a a a a a a a aa a a a a a a aa aaa a aaa ___SMSmessagetext I Description ee Note oo x OUTPUT 123324 0N eee 1 Output status is changed to ON Instead of numbers 1234 enter the OUTPUT 1234 OFF 1 Output status is changed to OFF Administrator or a User code i i OUTPUT _ 1234 _ PULSE 005 Output status is changed to ON for a Symbol _ indicates a space in SMS eee 5 time period entered in seconds message text x RESET 1234 Moduleisrestated U lt Titi duct cnn sented a s __ Power supply voltage DC12613V eee eee eee Used current i 60 100 mA stand by n 5 s L Upto 250 mA transmitting U U U UUUUUUUUUUUUUUUUIUITID Caaaaaaaaaa GSM modem frequency _850 900 1800OMHz UU x _ Memy o OOOO Up to 60 messages O O O 0 inputs _ Cat NCtype _Output __10C type commutating a direct 1 A current with 30 V voltage U Setting configuration Through the USB port O Z Z OO Operating environment _ From 10 C to 50 C with relative air humidity 80 with 20 C Dimensions 65 x 79 x25 mm aS a ua oe er ee eee ee see eee ee ao ee eae ee ee eo eo oe aro esse eee ee eee ee eee eC CoC Ce ree CC CE EE CC CCT CEECCCE EEE CCOCETE EE CCCEE EE CCCEE EE CCCEEEECCEEEEECCCCEEEECCCCEECECCCCE EEC COTE EE CCOCEECCCCCEEEOCCOCEEECECCECEECECCCEEEECCCCEEECCCCEEECCCE ECC CC CC EEE Package contents Module G10C 1 pc Adhesive fastening
Download Pdf Manuals
Related Search