UM0972110
Contents
1. Figure 4 Ch Camera settings E Camera tags Inte Figure 5 Language a On screen display Power settings ta CAN bus Figure 6 UM0972110 R1 3 Specialised Camera Solutions 4 Radar settings 4 1 Program the Sensor Each Sensor needs to be programmed Programming needs to be done with only one sensor connected to the monitor via the interface Open the service menu and go to system settings see figure 5 select the Radar setup menu see figure 8 Select the Sensor settings menu see figure 9 A warning is shown in the monitor see figure 10 If more Sensors are connected and you enter the sensor settings the Sensor with the lowest ID sensor direction is detected When Sensor have the same ID 2 sensor direction and sensor settings are entered shown radar type 50 Never change this when more than one Sensor is connected Changing the range will be applied at all Sensors with the lowest and same ID 4 1 1 Change sensor dir see figure 12 The sensor direction is the position of the Sensor or master slave pair on the vehicle As a guideline their positions are according to the setup shown in figure 12 A master slave pair must be programmed with the same sensor direction Default sensor direction is 1 4 1 1 1 Connect switch wires see figure 12 sensor direction 1 11 and 12 front radars can be switched or activated by with the brown switch wire sensor direction 5 6 and 72. RadarEye Sets with 7 and 12 Monitor User manual No UM0972110 R1 3 lll 08 2013 English Set with 7 Monitor easooses Set with 12 Monitor e ORLACO Specialised Camera Solutions User Manual Sets with 7 and 12 Monitor RadarEye F e8SSeses Manual No IM0972110 R1 2 N AZ Contents Page 1 Introduction 3 2 RadarEye set configuration 4 3 Monitor settings 6 3 1 Orlaco monitor keyboard 6 3 2 Service menu 6 3 3 Internal Buzzer 6 4 Radar settings 1 4 1 Program the Sensor T 4 1 1 Change sensor direction T 4 1 1 1 Connect switch wires T 4 1 2 Change Radar type T 4 1 3 Change range 8 4 1 4 Set seperation distance 8 4 1 5 Moving sensitivity and non moving sensitivity 8 4 2 Connecting Cameras and Sensors 8 4 3 Overlays 9 4 4 System settings 10 4 4 1 Setting zone to start the audible warning 10 4 4 2 Settings of the switch wires 11 4 4 3 External speaker settings 11 4 4 4 External messages 11 9 Diagnostics 13 6 Operation 13 6 2 Temporarily switch sound off detection 13 6 3 Check views displayed 14 6 4 Sensor failure 14 T Overview of menus 15 2 UM0972110 R1 3 m lt 9 OR ACO E pecialised Camera Solutions 1 Introduction Check with Orlaco which language versions are available This manual contains user instructions Used photographs and illustrations give general information and may differ from the products you
3. UM0972110 R1 3 Specialised Camera Solutions Overlay 3 9 Overlay 4 pe oystem RadarEye set corner rear ie Example application Wheelloader with camera at the motorcover Mounting height camera 2600mm Camera rotated down 42 separation distance 3100mm Detection range 15000mm Overlay 4 Overlay 5 system RadarEye set center rear Example application Reachstacker with camera at the counterweight Mounting height camera 2500mm Camera rotated down 45 Detection range 10000mm Overlay 5 The colors of the displayed overlay differ from the shown pictures S X Zone 5 and 4 are green zone 3 and 2 are yellow and zone 1 is red e camera SetCinas The camera must be positioned according to the chosen setup and Diagnose radar syst overlay 4 4 System settings Figure 19 In the system setting menu the start of the audible warnings the activation of the switch wires and the settings of the external buzzer Sm Switch front radars optional can be done S Switch rear radars si Block side speed gt OFF d Ext buz starts at 2 4 4 1 Setting zone to start the audible warning The detection range chapter 4 1 3 is automatically divided into 5 Figure 20 equally sized segments In this menu the zone where the audible warning is active can be set Open the service menu and go to system settings see figure 5 select the Radar setup menu see figure 8 Select the Systems settings menu
4. see figure 19 Choose a zone by buzzer starts at see figure 20 There are five zones to be set oee chapter 3 3 1 for an explanation for the adjustment of the volume of the internal buzzer 10 UM0972110 R1 3 OO ORLACO m 4 4 2 Settings of the switch wires As explained in chapter 4 1 1 1 The sensor directions can be activated via a switch wire See figure 21 When switch front radars is on figure 21 sensor directions 1 11 and 12 are only active when the brown switch wire is high When switch rear radars is on figure 21 sensor directions 5 6 and 7 are only active when the blue switch wire is high Default With the option Block side figure 22 speed sensor directions 2 3 4 and 8 9 10 are blocked with a speed signal on the grey switch wire The speed is adjustable OFF 5 10 15 20 25 30 35 40 45 50 km h For example When RadarEye is applied in a rearview system set sensor direction to 5 6 or and connect the blue wire to the reverse signal Camera is always active but RadarEye is only active when reverse is active How to set the Tacho Pulses Select system settings Press enter to open the System settings menu See figure 8 Use the minus 6 or the plus key 7 to go to the option Front Camera This option opens the front camera sub menu of the monitor This offers the option Pulses per metre Set the amount of pulses per metre that is sent to the monitor of the tacho switching wir
5. No 0401320 Bracket SRD Sensor center rear 1 x Art no 0301080 0 25m M12 M S Red range 2m 20m j 1 x Art No 0350110 M12 Terminator 120 Ohm Figure 1 Explanation D Radar Cable A Monitor E Radar Set center rear B Camera Cable K Radar connecting cable C Camera 4 UM0972110 R1 3 ORlACO Specialised Camera Solutions set Article No 0403120 Set SRD Corner Rear consisting of 2 wide beam Sensors 70 beam width 11 beam height that work together to guard a rectangular area see figure 2 RadarEye set corner rear system overview Camera C Monitor A ao 7 green F f i K l Master Slave D Set Art No 0403120 range 2m 20m Set SRD Corner Rear Art No 0403120 consisting of 2 X Art No 0004310 SRD Sensor CAN Horizontal 2 X Art No 0401330 Bracket SRD Sensor Corner Rear 1 x Art No 0350110 M12 Terminator 120 Ohm Figure 2 Explanation D Radar Cable A Monitor H Radar Set corner rear B Camera Cable K Radar connecting cable C Camera UM0972110 R1 3 5 Xna OR ACO H H Y pecialised Camera Soluti 3 Monitor settings 3 1 Orlaco 7 and 12 Monitor keyboard Button No 1 Camera selection Button No 2 Auto LCD Backlight Control Day Night modes Button No 3 Contrast Button No 4 Brightness Button No 5 Option previous menu Button No 6 Selection setting Button
6. objective is to design and produce camera systems for the professional market that improve the drivers view and increase operating efficiency At our facility in Barneveld we locate our design manufacturing warehousing and service department Vision is our mission Orlaco therefore deploys the development manufacture supply and service of camera and Monitor systems that will improve safety and efficiency of all vehicles machinery and vessels Our systems give the end user a view on each blind spot and will create comfort and improved working conditions Our active approach will support market demands and innovations and will lead to enthusiastic ambassadors in the market our customers For more information www orlaco com ORLACO PRODUCTS BV Albert Plesmanstraat 42 3772 MN Barneveld PO Box 193 3770 AD Barneveld The Netherlands Phone 31 0 342 404555 Fax 31 0 342 404556 E mail info orlaco com Internet http www orlaco com ea ORLACO Specialised Camera Solutions
7. separation distance is 4 0m 40 4 1 5 Moving sensitivity and non moving sensitivity Moving sensitivity and non moving sensitivity are not used in the current software 4 2 Connecting Cameras and Sensors The connection between cameras and sensor is programmed in the Radar menu The camera is connected to the sensor direction programmed in the Sensor s Open the service menu and go to system settings see figure 5 select the Radar setup menu see figure 8 Select the Camera settings menu see figure 14 There can be three View 1 3 sensor directions connected to one camera The number indicates the direction where the sensor is looking as per the clockwheel convention Default view 1 for Cam 1 is set to sensor direction 6 see figure 15 setting up Cam 1 to look at sensor 6 means that camera 1 is looking in the same rear direction as sensor 6 and that the monitor will switch to camera 1 as soon as sensor s 6 detects an object see figure 15 Setting up Cam 1 to look at sensors 5 6 and 7 mean that camera 1 is looking in the same rear direction as sensor 5 6 and 7 and that the monitor will switch to camera 1 as soon as either or all sensor 9 6 or 7 detect an object see figure 16 8 nios en RIYIN Buttons1 2 34 5 6 7 8 Range 2m 20m Figure 13 D 5 vatem seti l ngs a Sensor settings Diagnose radar syst Figure 14 View 1 View 2 View 3 Overlay Figure 16
8. No 7 Selection setting Button No 8 Enter Standby 3 2 service menu Adjustment of the monitor settings is done via the service menu To open the service menu simultaneously press the camera selection button 1 the minus button 6 and the plus button 7 see Figure 3 The monitor Service menu see Figure 4 will appear The following buttons are used to navigate through the menus 5 Option previous menu Return to the previous menu 6 Minus Go to the next menu option 7 Plus Go to the previous menu option 8 Enter Select or enable the chosen option 3 3 Internal Buzzer The monitor is equipped with an internal buzzer To adjust the volume of the settings see figure 5 Select the keyboard menu see figure 6 Select Beeper Volume to adjust Default setting of the volume is 100 see figure 7 Keyboard sound to ALM Alarm as default When the system is equipped with an external loudspeaker part 0504820 and you want to de activate the internal buzzer open the service menu and go to system settings see figure 5 Select the keyboard menu see figure 6 settings of the external speaker are done in the radarmenu see chapter 4 4 3 6 objects in m monitor are oe d e e e e e e closer than Cie they appear Buttons1 2 3 4 5 6 7 8 7 monitor Keyboard N CORR GIC J CO 12 monitor Keyboard Button 1 Buttons 6 7 Figure 3 Ch MEN 14 tags A System settings Inte
9. UM0972110 R1 3 Specialised Camera Solutions 4 3 Overlays The standard visible warning is with colored dots in the above right corner in the monitor see figure 17 It is possible to change this to an overlay There are 5 pre programmed overlays which are designed to match with a system setting and installation of the camera and Sensors Each overlay is designed to match with a camera with an opening angle of 118 degrees Selected overlay is displayed on view 1 see figure 18 Changing from the dots to an overlay can be done per camera and is done in the camera settings in the Radar setup menu Open the service menu and go to system settings see figure 5 select the Radar setup menu see figure 8 select camera settings select Overlay see figure 18 Overlay 1 system RadarEye set corner rear Example application Lorry with camera at the top of the roof Mounting height camera 3900mm Camera rotated down 42 Bumper of lorry is shown separation distance 2 50mm Detection range 6000mm Overlay 2 system RadarEye set corner rear Example application Lorry with camera at the bumper Mounting height camera 1000mm Camera rotated down 42 Bumper of lorry is shown Separation distance 2 50mm Detection range 6000mm Overlay 3 system RadarEye set center rear Example application Dumptruck with camera at the bumper Mounting height camera 1600mm Camera rotated down 78 Detection range 10000mm
10. ce is switched via a relais in the 0504820 settings of the relais are done in the systems setting in the radar menu See figure 24 Relais activates at The zone where the signal output on the relais starts can be adjusted More info about the external messages and connections can be found in the datasheet and system manual Orlaco Radar monitor will report the detected zone 10 times per second on the RS232 interface RS232 parameters 9600 baud 8 bits no parity The following packet will be sent 0x80 0x01 0x40 0x03 Status Zone OxFF no packet within 200ms indicates total radar system failure The Status byte can have the following values Status value Meaning Status 0 gt No Error Status 1 gt Error detected zone detection not reliable The Zone byte can have the following values Zone value Meaning Zone 0 gt No Object NOTE lt Zone gt 1 gt Closest zone Red ORLACO PRESENTS THE lt Zone gt 2 gt Yellow RADAR SIGNAL AVAILABLE Zone 3 gt Yellow BUT WILL NOT BE LIABLE IF IT Zone 4 gt Green IS USED TO INTERVENE IN THE Zone 5 gt Farthest zone Green MACHINE 12 UM0972110 R1 3 OO ORLACO EN pecialised Camera Solutions 5 Diagnostics CTI TXXYXXx This will give you an overview of the RadarEye system Butons 2 34 56 7 8 Open the service menu and go to system settings see figure 5 select the Radar setup menu see fig
11. e AUX1 grey see also Frontcam Manual 1M0993850 4 4 3 External speaker settings Optional the 0504820 Interface Box with Ext speaker CAN SRD camera is available This is an interface box with external speaker and a LED light For this external speaker the settings can be adjusted See figure 23 Ext buz start at The zone where the audible warning on the external speaker starts can be adjusted Ext buzzer volume Adjusting the volume of the external speaker Ext LED lights at The zone where the visible LED warning on the external speaker starts can be adjusted UM0972110 R1 3 J Buzzer starts at zi e Switch rear radars rial a Block side speed gt OFI oy Ext bus starts at 3 Li Figure 21 t Buzzer starts at Switch front radars i Switch rear radars t Ext bu Starts at Figure 22 n Switch rear radars Block side speed gt Dp f elg a MUFFE r wo LITT TE xt LED lights at F H Figure 23 11 Specialised Camera Solutions 4 4 4 External messages E The optional 0504820 Interface Box with Ext speaker CAN SRD Block side speed gt OFI camera has the possibility to send out external signals about the 2r buz starts at 5 xt buzzer volume zT detection amp Ext LEO lights at These signals are RS232 en RS485 stop indications output There is also a possibility to connect an external indicator for Figure 24 example tower light This external devi
12. rear radars can be switched or activated with the blue switch wire sensor direction 2 3 4 and 8 9 10 can be blocked with a speed signal on the grey switch wire For settings of the switch wires see chapter 4 4 2 4 1 2 Change radar type The type of the Sensor can be programmed This determines which function the Sensor has in the system The default Sensor type is 2 Possible settings are 1 Slave to a dual sensor master type 2 or 3 2 Master for corner rear setup AND function 3 Master for center rear setup OR function 4 Single master Sensor not paired 5 Single slave Sensor paired with type 4 UM0972110 R1 3 Specialised Camera Solutions amp Keyboard lock a Keyboard sound Figure 7 al Camera switch 2 Frontcam a Default settings e Ext device config Figure 8 D System settings Cc Camera settings Diagnose radar syst Figure 9 Figure 10 Change radar type Change range Set seperation dist i Moving sensitivity Figure 12 7 4 1 3 Change range set the range of detection The range can be set from 20 200 decimeter these are divided into 5 equally sized segments see figure 13 The default detection range is 6m 60 4 1 4 Set seperation dist Set the separation Distance This is the distance between a master and slave It can only be set or changed when radar type 2 is selected master for corner rear setup The default separation distance is 2 5m 25 Max
13. s the vehicle gets closer to an object 6 2 Temporarily switch sound off detection Press on the Option previous button 5 to put the buzzer off and the camera locked when a object disappears the system will reboot automatically UM0972110 R1 3 13 es 59 ORL ACO guys 6 3 Check views displayed When check views is displayed in the monitor RadarEye has detected an object but camera is manually locked The LED next to button 1 is blinking 6 4 Sensor Failure If the buzzer sounds and a red cross is displayed the sensor has failed Please check the Sensor or connections 14 UM0972110 R1 3 ORL ACO gee pecialised Camera Solutions 1 Overview of menus Service menu Camera Minus and Plus buttons Frontcam Diagnose radar sys s OFF 1 2 3 4 5 s gt ON OFF gt ON OFF 40 45 50 gt OFF 5 10 15 20 25 30 35 gt OFF 1 2 3 4 5 gt 0 100 gt OFF 1 2 3 4 5 gt OFF 1 2 3 4 5 View p OFF 1 12 View2 OFF 1 12 View3 OFF 1 12 Overlay J OFF 1 2 3 4 5 gt Sensor settings Diagnose radar syst Zone Range d d A These menus are explained in the User Manual UM0972080 UM0972110 R1 3 15 nn 9 ORL ACO Specialised Camera Solutions ORLACO Orlaco is a Manufacturing company that specializes in making cameras and monitor systems for commercial vehicles fork lift trucks cranes off shore and maritime Our
14. ure 8 Select the Diagnose radar syst menu see figure 25 E Cited setting a Sensor settings When activating the Diagnose radar syst menu the shown mode is Zone With the enter button 8 you can change mode to Zone Type Figure 25 Range and Distance see figure 26 Mode fone ot Indicates that that specific sensor is not used Eront gt 4 allocated to a camera a NK OK Allocated and connected sensor OK no e o Beene some object in range or the distance to the object in range with colored dots Figure 26 Data Means that data is received from that sensor However the sensor is not allocated to a camera NotDet Means that the sensor is allocated to a camera however no data is received from a sensor with that ID Err01 Means there is no communication between Master and Slave 6 Operation 6 1 RADAR OK displayed All measurable parameters and the flow of data from all connected sensors are diagnosed and OK There is no fault message detected from the sensors and the sensors are operative there are no measurable sensor errors and detections of objects The range indicator in the display gives the operator a relative distance measurement to the closest detected object Indicate 5 dots operate from the left green to right red with a closer object resulting in more dots See figure 27 Figure 27 The buzzer sounds audible tones to alert the operator to obstacles The buzzer tone rate will increase a
15. use Contact your Orlaco dealer if you have questions additional information or want to make changes that are not described in this manual The camera Monitor systems from Orlaco comply with the latest CE ADR EMC and mirror directive regulations All products are manufactured in accordance with the ISO 9001 quality management system IS0 TS16949 quality automotive and ISO 14001 environ mental management systems Available documentation system Manual IM0974110 for installation Data sheet DS0208371 Monitor 7 LEDD CAN SRD 6 Data sheet DS0208871 Monitor 7 RLED CAN SRD R6 Data sheet DS0209110 Monitor 7 RLED CAN SRD 4 CAM 7 4 Data sheet DS0411300 Set Monitor 12 RLED CAN SRD R6 Release notes R1 0 First issue August 2013 R1 1 Article names changed October 2013 R1 2 Chapter 7 added November 2013 R1 3 Multiple text changes March 2014 UM0972110 R1 3 3 n Em 9 OR ACO pups ecialised Camera Solutions 2 RadarEye set configuration Set Article No 0403100 Set SRD Center Rear consisting of 2 wide beam Sensors 70 beam width 11 beam height that work together to guard a wide area see figure 1 RadarEye set center rear system overview Camera C Monitor A Set Art No 0403100 r Master Slave ITE Terminator Interface Set SRD Center Rear Art No 0403100 consisting of 2 X Art No 0004320 SRD sensor CAN vertical 1 x Art
Download Pdf Manuals
Related Search
UM0972110