USERS GUIDE - Big Boiler Shop
Contents
1. USERS GUIDE Esprit eco 24 30 For installation guide see reverse of book When replacing any part on this appliance use only spare parts that you can be assured conform to the safety and performance specification that we require Do not use reconditioned or copy parts that have not been clearly authorised by Ideal p m m eS SS eee ee ee ee ee ee ee ee ee eee ee ee ee ee ee ee ee ee eee eee ee ee ee ee ee ee ee ee l FOR aNy qUERIEs pLEasE RINg ThE l l EspRIT ECO CONSUMER hELpLINE 01482 498660 l I NOTE BOILER RESET pROCEDURE l I To reset boiler turn mode control knob to reset position and immediately turn knob back to required setting l Introduction Minimum Clearances The Esprit eco is a wall mounted room sealed condensing Clearances of 165mm 6 1 2 above 100mm 4 below combination boiler featuring full sequence automatic spark ignition 2 5mm 1 8 at the sides and 450mm 17 3 4 at the front of and fan assisted combustion the boiler casing must be allowed for servicing Due to the high efficiency of the boiler condensate is produced from Bottom clearance the flue gases and this is drained to a suitable disposal point through Bottom clearance after installation can be reduced to 5mm a plastic waste pipe at the base of the boiler A condensate plume This must be obtained with an easily removable panel to will also be visible at the flue terminal enable the consumer to view the system pressure gauge2. and The Esprit eco is a combination boiler providing both central heating to provide the 100mm clearance required for servicing and instantaneous domestic hot water To light the boiler refer to Frame 1 safety Current Gas Safety Installation amp Use 1 CHECK THAT THE ELECTRICITY SUPPLY TO BOILER IS regulations or rules in force OFF In your own interest and that of safety it is the law that this boiler 2 Set the mode knob control A to Off must be installed by a Gas Safe Registered Engineer in accordance 3 with the above regulations In IE the installation must be carried out by a Registered Gas Installer RGII and installed in accordance with the current edition of l S 813 Domestic Gas Installations the current Building Regulations and reference should be made to the current ETCI rules for electrical Set the Domestic Hot Water temperature control B and Central Heating temperature control C to max Ensure that all hot water taps are turned off 5 Switch ON electricity to the boiler and check that all controls e g timer and room thermostat are ON refer to mechanical timer instructions Page 4 gt installation It is essential that the instructions in this booklet are strictly followed 6 Set the mode knob control to winter T for safe and economical operation of the boiler If there is a central heating demand the boiler will commence the ignition sequence Electricity su
3. Contact a qualified electrician or your electricity provider Unconfigured PCB Please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII 1 Turn power off and on at the fused spur 2 If the boiler fails to operate please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII Reset the appliance if the boiler fails to operate then please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII Reset the appliance if the boiler fails to operate then please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII Check system pressure is between 1 amp 1 5bar on the pressure gauge If the boiler fails to operate then please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII 1 Check other gas appliances in the house are working to confirm a supply is present in the property 2 If other appliances do not work or there are no other appliances che
4. 4 Once the blockage is removed and the condensate can flow freely reset the appliance Refer to To Light the boiler 5 If the appliance fails to ignite call your Gas Safe Registered engineer Preventative solutions During cold weather set the boiler stat to maximum Must return to original setting once cold spell is over Place the heating on continuous and turn the room stat down to 15 C overnight or when unoccupied Return to normal after cold spell Escape of gas Should a gas leak or fault be suspected contact the National Gas Emergency Service without delay Telephone 0800 111 999 Do NOT search for gas leaks with a naked flame Cleaning For normal cleaning simply dust with a dry cloth To remove stubborn marks and stains wipe with a damp cloth and finish off with a dry cloth dO nOT use abrasive cleaning materials Maintenance The appliance should be serviced at least once a year by a Gas Safe Registered Engineer or in IE a Registered Gas Installer RGII Esprit eco Installation and Servicing MEChaNIiCaL 24 hOUR TIMER pROgRaMMINg ThE TIMER 1 Decide what times you would like the timeswitch to switch ON and OFF 2 Push segments towards the programme ring for an OFF period and push away from ring for an ON period The minimum switching interval is 15 minutes and this can be increased in 15 minute steps 3 Bring the timeswitch into the correct condition by manually turning the programme rin
5. Should this occur a fault code F 2 will be displayed Refer to fault chart continued Legend Mode Control Knob DHW Preheat Control Knob CH Control Knob Boiler Status Burner on Indication Pre Heat on off Indication Programmer Pressure Gauge Condensate Drain A B C D E F G H J Esprit eco Installation and Servicing Loss of system water pressure The gauge H indicates the central heating system pressure If the pressure is seen to fall below the original installation pressure of 1 2 bar over a period of time then a water leak may be indicated In this event re pressurise the boiler If unable to do so or if the pressure continues to drop a Gas Safe Registered Engineer or in IE a Registered Gas Installer RGII should be consulted INDICATED BY F1 LOW WATER PRESSURE THE BOILER WILL NOT OPERATE IF THE PRESSURE HAS REDUCED TO LESS THAN 0 3 BAR UNDER THIS CONDITION 3G9933 PRESSURE GAUGE Condensate Drain This appliance is fitted with a siphonic condensate trap system that reduces the risk of the appliance condensate from freezing However should the condensate pipe to this appliance freeze please follow these instructions a If you do not feel competent to carry out the defrosting instructions be
6. ck the gas supply is on at the meter and or pre payment meter has credit If the boiler fails to operate then please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII Reset the appliance if the boiler fails to operate then please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII Reset the appliance if the boiler fails to operate then please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII Reset the appliance if the boiler fails to operate then please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII Esprit eco Installation and Servicing
7. e awaiting either a central heating call or hot water demand 0 burner The boiler has a call for central heating but the appliance has reached the desired E temperature set on the boiler burner The boiler has a call for hot water but the appliance has reached the desired temperature set on d the boiler burner The boiler is operating in central heating mode C burner The boiler is operating in hot water mode d burner The boiler is operating in pre heat mode burner The boiler is operating in frost mode continued Esprit eco Installation and Servicing 7 FaULT CODEs DispLay CODE ON BOILER burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner burner DEsCRIpTION Outside Sensor Failure Low Mains Voltage Unconfigured PCB 5 Boiler Resets in 15 minutes False Flame Lockout BCC Activation Fault BCC Fault Low Water Pressure Flow Temperature Overheat Flame Loss Ignition Lockout Fan Fault Flow Thermistor Return Thermistor aCTION Reset the appliance if the boiler fails to operate then please contact Ideal Boilers if under warranty or alternatively a Gas Safe Registered Engineer if outside of the warranty period In IE contact a Registered Gas Installer RGII
8. e in this mode if the CH temperature control C is set to the e position economy mode This control should be set to maximum for very cold periods 1 BOILER CONTROLS Weather Compensation When the Weather Compensation option is fitted to the system then the CH Temperature Control C becomes a method of controlling room temperature Turn the knob clockwise to increase room temperature and anti clockwise to decrease room temperature Once the desired setting has been achieved leave the knob in this position and the system will automatically achieve the desired room temperature for all outside weather conditions To shut down the boiler Set the mode knob control to OFF To relight the boiler Repeat the procedure detailed in To light the boiler Frost protection If no system frost protection is provided and frost is likely during a short absence from home leave the heating controls if fitted at a reduced temperature setting For longer periods the entire system should be drained If the system includes a frost thermostat then during cold weather the boiler should be turned OFF at the time switch if fitted ONLY The mains supply should be left switched ON with the boiler thermostat left in the normal running position Boiler Overheat Protection The boiler controls will shut down the boiler in the event of overheating Should this occur a fault code L will be displayed Refer to fault chart Flame Failure
9. g clockwise through a 24 hour cycle 4 Turn the programme ring clockwise until the correct time of day on the ring lines up with the time indicator note The segment dial can be turned when the time controller is operating In case of power failure re adjust the time controller to the correct time of day turning the dial in a clockwise direction permanent Override By rotating the central switch so that the symbol 1 lines up with the time indicator Y the unit will be permanently ON With the symbol lining up with the time indicator Y the unit acts as a timeswitch With the symbol 0 lining up with the time indicator Y the unit will be permanently OFF Esprit eco Installation and Servicing Permanently ON Time amp Control Indicator ON segment 24hr Programme Ring Timer control segments 1 Segment 15 mins Push towards programme ring OFF Push away from programme ring ON pOINTs FOR ThE BOILER UsER Note n line with our current warranty policy we would ask that you check through the Troubleshooting guide to identify any problems external to the boiler prior to requesting a service engineers visit Should the problem be found to be other than with the appliance we reserve the right to levy a charge for the visit or for any pre arranged visit where access is not gained by the engineer TROUBLEShOOTINg NO hOT WaTER NO CENTRaL hEa TINg NO hOT WaTER OR CENTRaL hEa TINg Check the mai
10. ion and immediately turn knob back to required setting The boiler will repeat the ignition sequence If the boiler still fails to light Children should be supervised to ensure that they do not play with consult a Gas Safe Registered Engineer or in IE a Registered the appliance Gas Installer RGII In cases of repeated or continuous shutdown a Gas Safe Registered Engineer or in IE a Registered Gas Installer RGII should be called to investigate and rectify the condition causing this and carry out an operational test Only the manufacturers original parts should be used for replacement All Gas Safe Register installers carry a Gas Safe Register ID card and have a registration number Both should be recorded in the Benchmark Commissioning Checklist You can check your installer by calling Gas Safe Register direct on 0800 4085500 Ideal is a member of the Benchmark scheme and fully supports the aims of the programme Benchmark has been introduced to improve the standards of installation and commissioning of A central heating systems in the UK and to encourage the regular servicing of all central heating enc mar systems to ensure safety and efficiency ThE BENChMaRK sERVICE INTERV aL RECORD MUsT BE COMpLETED aFTER EaCh sERVICE THE MARK OF QUALITY FOR THE INSTALLATION COMMISSIONING AND SERVICING OF DOMESTIC HEATING AND HOT WATER SYSTEMS 2 Esprit eco Installation and Servicing Operation Winter conditions i e Ch a
11. low please call your local Gas Safe Registered installer for assistance b If you do feel competent to carry out the following instructions please do so with care when handling hot utensils Do not attempt to thaw pipework above ground level If this appliance develops a blockage in its condensate pipe its condensate will build up to a point where it will make a gurgling noise prior to locking out an L2 fault code If the appliance is reset it will make a gurgling noise prior to it locking out on a failed ignition L2 code To unblock a frozen condensate pipe 1 Follow the routing of the plastic pipe from its exit point on the appliance through its route to its termination point Locate the frozen blockage It is likely that the pipe is frozen at the most exposed point external to the building or where there is some obstruction to flow This could be at the open end of the pipe at a bend or elbow or where there is a dip in the pipe in which condensate can collect The location of the blockage should be identified as closely as possible before taking further action 2 Apply a hot water bottle microwaveable heat pack or a warm damp cloth to the frozen blockage area Several applications may have to be made before it fully defrosts Warm water can also be poured onto the pipe from a watering can or similar DO NOT use boiling water 3 Caution when using warm water as this may freeze and cause other localised hazards
12. nd DhW required Ensure the mode knob control A is set to winter T The boiler will fire and supply heat to the radiators but will give priority to DHW on demand summer conditions i e DhW only required Set the mode knob control to Summer Set the CH external controls to OFF note The pump will operate briefly as a self check once every 24 hours regardless of system demand Pre heat is enabled if the pre heat indicator F is lit To switch pre heat on or off move the DHW Pre heat control knob B fully clockwise and then return it to the required DHW temperature setting Control of water temperature Domestic hot Water The DHW temperature is limited by the boiler controls to 64 C maximum at low draw off rate adjustable via the DHW temperature control B Due to system variations and seasonal temperature fluctuations DHW flow rates temperature rise will vary requiring adjustment at the draw off tap the lower the rate the higher the temperature and vice versa Approx flow temperatures for the boiler thermostat settings are Knob setting Minimum Flow Temperature 40 C 104 F 64 C 147 F Maximum Central heating The boiler controls the central heating radiator temperature to a maximum of 80 C adjustable via the CH temperature control C The boiler is a high efficiency combination boiler which is most efficient when operating in condensing mode The boiler will operat
13. ns switch fused Check the mains switch fused spur is turned on and ensure spur is turned on and ensure Check the fused spur is turned switch mode control knob A is switch mode control knob A is on and ensure switch mode in the summer or winter position in the winter position control knob A is in the winter position Check the timer is in an ON position and the room thermostat Does the boiler have a display is turned up showing on the front control panel Is water coming out of the hot water tap when turned on See boiler Fault Codes Does the boiler operate and ee Oan AUT OGES provide central heating See boiler Operation Modes section If 0 is displayed then i and Fault Codes section contact Ideal Boilers if your appliance is under warranty or a Gas Safe Registered Engineer Check the time settings on the in IE a Registered Gas Installer programmer are as you require Contact a Gas Safe Registered RGIl if out of warranty and adjust if necessary Engineer or in IE a Registered Gas Installer RGII See boiler Operation Modes and Fault Codes section If 0 is Contact a Gas Safe Registered displayed then contact a Gas Safe Engineer or in IE a Registered Registered Engineer or in IE a Gas Installer RGII Registered Gas Installer RGII 6 Esprit eco Installation and Servicing OpERa TION MODEs DispLay CODE ON BOILER DEsCRIpTION burner The boiler is in standby mod
14. pply Note n normal operation the boiler status display D will This appliance must be earthed show codes supply 230 V 50 hz The fusing should be 3a Standby no demand for heat importan notes CH being supplied This appliance must not be operated without the casing correctly fitted and forming an adequate seal Ifthe boiler is installed in a compartment then the compartment MUST NOT be used for storage purposes e F ee F ne Boiler frost protection boiler will fire if temperature is f it is known or suspected that a fault exists on the boiler then below 5 degrees C it MUST NOT BE USED until the fault has been corrected by a Gas Safe Registered Engineer or in IE a Registered Gas Installer During normal operation the burner on indicator E will remain RGIl illuminated when the burner is lit Under NO circumstances should any of the sealed components on this appliance be used incorrectly or tampered with This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or RESET pROCEDURE lack of experience and knowledge unless they have been given supervision or instructions concerning use of the appliance by a person responsible for their safety DHW being supplied DHW preheat WTA N Note If the boiler fails to light after five attempts the fault code L will be displayed To reset boiler turn the mode control knob A to reset posit
Download Pdf Manuals
Related Search