Speed Seed - Charterhouse Turf Machinery
Contents
1. ONDARY 11 i D 6G AQ AA m rS E D q Ten Specdseed 9 Speedsee d z a du fd 3v Fig 7 Safety sticker RA read user manual before use toolbox Safety sticker 911 280 402 keep a distance of at least 4 metres from the machine Stop the engine before carrying out repairs or adjustments Make sure all stickers are clearly visible on the machine and are understood The serial number is at the front on the three point plate of the machine Three point fastening pins Free adjustable brush Access hatch to the transmission for setting the seeding density Seeding wheel adjusting to the area Seed tray Here also the various change gears for configuring the required seeding density are found Cover providing access to the secondary drive chain and tensioner Adjustment screw of chain tensioner primary drive chain Sticker indicating the various gear settings and the associated seeding densities 10 4 0 ADJUSTING THE WORKING DEPTH The working depth can be adjusted by turning the top rod When the top rod is turned and consequently shortened the machine will incline forwards setting the seeding depth lower This works when the ground to be tilled is soft enough When the ground is not soft enough try to make this softer by using irrigation or the verti drain 5 0 SETTING THE SEED QUANTITY The seed quantity can be set on the Speedseed Q9 by2. Weight 550 g 772 lbs 700kg 992 Ibs Seeding hole spacing Square 30 mm 1 18 Square 30 mm 1 18 Number holes sq meter with single spiked roller 990 990 Recommended tractor 40 HP with minimum lifting capacity of 1000 kg 2200 Ibs 40 HP with minimum lifting capacity of 1000 kg 2200 Ibs Seed tray capacity 225 litres 7 9 cu ft 336 litres 11 8 cu ft Maximum capacity theoretically at maximum speed 12 km h 7 5 mph and single passage 24900 m 268021 ft 28350 m 305046 ft Seeding density per 100 m 1076 4 ft Fine seed 0 2 2 8 kg 0 44 6 17 lbs adjustable in 10 steps Coarse seed 0 2 4 kg 0 44 8 82 Ibs adjustable in 10 steps Fine seed 0 2 2 8 kg 0 44 6 17 Ibs adjustable in 10 steps Coarse seed 0 2 4 kg 0 44 8 82 lbs adjustable in 10 steps Shipping dimensions LxWxH 2415 x 870 x 1070 mm 134x34x42 LxWxH 2700 x 870 x 1070 mm 150x34x42 Three point connection Three point CAT 1 2 Three point CAT 1 2 Lubricant EP 2 EP 2 Tyre pressure 1 2 bar 14 5 29 psi Standard parts 5 gear sets for adjusting the seeding density Manual container Seed tray with sight glass Seeding wheel adjusting to the area 5 gear sets for adjusting the seeding density Manual container Seed tray with sight glass Seeding wheel adjusting to the area
3. While agjusting the machine tractor combination must be fully locked to prevent it from driving sliding sinking away The tractor engine must be switched off 7 Increase the speed until the correct driving speed has been reached STOP SEEDING 1 Decrease the driving speed to about 3 km h 1 9 mph 2 While driving raise the machine out of the ground 3 Goto the following place and start again as described It is absolutely imperative that the above procedures are followed While driving lower the machine CAREFULLY AND IN A CONTROLLED WAY during the tilling NEVER drive backwards when the running wheel is on the ground 11 0 DISCONNECTING THE SPEEDSEED The machine can be disconnected from the tractor as follows 1 Slowly lower the machine until it stands on the ground 2 Lockthe roller to prevent it from rolling away 3 Loosen the top rod and remove it 4 Remove the lower arms from the tractor of the speedseed Place the machine on a stable and level surface and make sure that the machine is stable and cannot slide i Switch off the tractor engine when people are walking around the machine and lock the tractor machine combination to prevent it from moving When you store the machine lower the machine carreful to prefent the spikes against damage 13 12 0 TROUBLESHOOTING Problem Possible cause Solution Seed is spoilt from the seed Seeding slit too large Readjust the seeding slit t
4. Option Set of spikes for back roller Set of spikes for back roller I A Y SA NY NY N p fo g Speedseed CERES x 7 Lg AES bo PAN o i o j Speedseed Fig 6 2 0 FIRST INSTALLATION REMOVING THE MACHINE FROM THE PALLET The machine is standing vertically on the pallet To remove the pallet and lay the machine horizontally on the ground proceed as follows see Fig 6 1 Fasten a cable to the lifting point 2 Make sure that the cable crane lift can lift at least SS 1200 SS 1600 SS 2100 SS 2400 500 kg 1100 Ibs 600 kg 1322 Ibs 700 kg 1540 Ibs 850 kg 1870 Ibs 2 Raise the machine including the pallet 50 mm 2 from the ground 3 Remove the pallet by sliding it over the lower 3 point pins Do not crawl under the machine ort Slowly lower the machine until it is standing on the ground Attach the machine to a tractor Use the correct tractor See the specifications o ON from driving sliding away Set the tractor s stabiliser to 100 mm lateral movement Drive to the area that is to be tilled While driving carefully lower the machine into the ground Switch off the tractor and lock the tractor Speedseed combination to prevent it 10 Turn the top rod to adjust the machine angle to 90 degrees 3 0 GENERAL PARTS LIST Figure 7 shows some important parts
5. The manufacturer does not accept any liability with regard to damage resulting from incorrect use all resulting risks are the responsibility of the user Correct use also includes following the manufacturer s instructions for use maintenance and repair Before using the Speedseed inspect the area to be treated Remove any loose obstacles and avoid irregularities The Speedseed was constructed according to the latest technological knowledge and is safe to use Improper use maintenance or repair of the machine may result in injury to both the user and others This should be avoided Always use the Speedseed in combination with the appropriate tractor as described in the technical data All persons whom the owner assigns to operate maintain or repair the Overseeder must read and completely understand the operating manual and in particular the Safety Instructions section The user is responsible for a safe tractor Speedseed combination This unit must be tested in terms of noise safety and ease of use In addition user s instructions must be prepared Before using the Speedseed the user is obliged to inspect it for visible damage and defects Any changes of the Speedseed including its functioning that may affect its safety must be corrected immediately For safety reasons it is in principle forbidden to make changes in or additions to the Speedseed with the exception of those approved by the manufacturer If any modificati
6. one till you start working without the spikes on the second roller again Demount the brush 4 and the blockbolts 5 To remove the brush only demount bolt 6 Do not remove bolt 7 Assemble inside the rear roller 1 on one side the four bolt M8 x 16 8 with the self lock nuts 9 Assemble the spikes on the roller 10 Assemble the other side also the four bolts M8 x 16 9 with the self lock nuts 10 Assemble the roller 1 in the holes 11 11 Assemble the brush 4 with the blockbolts 5 in the holles 12 12 Assemble the rear cover 2 13 Lower the machine to the ground e gpeedseed MN s 5 18 16 2 OPTION WHEEL KIT Article number for this is 224 160 000 and is only arranged for the speedseed 1600 This kit will be separately delivered and can be mounted to a standard 3 point linkage machine Generally speaking a machine with wheel kit will reduce the minimum horsepower required by 10 HP It also can be taken off quickly so the machine can be used either way Front View Back View 19
7. using Top cear E various change gears n These provide various combinations for a j broad range of settings see Tab 1 n The gears have been marked with a number S given in Tab 1 by changing the gears as indicated the required A 4 quantity setting is obtained The different combinations of gears have been installed in the seed tray Fig 8 Gear option Bentgrass Kentucky Bluegrass Ryegrass Bottom Top Kg 100m Lbs 1000ft Kg 100m Lbs 1000ft Kg 100m Lbs 1000ft 25 95 0 20 0 40 0 20 0 40 0 30 0 60 40 80 0 40 0 80 0 35 0 70 0 55 1 10 45 75 0 45 0 80 0 40 0 80 0 65 1 30 52 68 0 60 1 20 0 50 1 00 0 85 1 75 58 62 0 70 1 40 0 60 1 20 1 00 2 00 62 58 0 80 1 60 0 75 1 50 1 20 2 45 68 52 1 00 2 00 0 90 1 80 1 40 2 80 75 45 1 30 2 60 1 10 2 20 1 90 3 85 80 40 1 50 3 00 1 40 2 80 2 20 4 45 95 25 2 80 5 70 2 60 5 30 4 15 8 40 Tab 1 These quantities are determined with a slit distance of 0 3 mm between the seeding roller and the pressure plate see section 15 0 for setting In practice the quantities described in Tab 1 may deviate to some extent due to other measuring working conditions In order to determine exactly the right seeding quantity for the seed used it is recommended to carry out a spreading test see section 15 2 11 6 0 TRANSPORTING THE SPEEDSEED The user is responsible for the transport of the Speedseed behind t
8. NTENTS Section Description Page Foreword 2 Guarantee conditions 2 Registration card 2 Safety instructions 3 1 0 Technical data 7 2 0 First installation removing the machine from the pallet 9 3 0 General parts list 10 4 0 Adjusting the working depth 11 5 0 Setting the seed quantity 11 6 0 Transporting the speedseed 12 7 0 Driving speed 12 8 0 General remarks on the use of the speedseed 12 9 0 Operating the speedseed 12 10 0 Start stop procedure 12 11 0 Disconnecting the speedseed 13 12 0 Troubleshooting 14 13 0 EU certificate 14 14 0 Maintenance 15 15 0 Adjusting the seeding slit opening 16 15 1 Adjusting the seed tray scraper 16 15 2 Spreading test 17 16 1 Option Spikes on rear roller 18 16 2 Option wheel kit 19 Parts pages 1 0 TECHNICAL DATA Model Working width 1200 1 2 m 82 7 1600 1 58 m 94 4 Working depth 5 mm 20 mm 0 19 0 78 5 mm 20 mm 0 19 0 78 Seeding speed Up to 12 km h 7 5 mph Up to 12 km h 7 5 mph Weight 350 g 772 Ibs 450kg 992 Ibs Seeding hole spacing Square 30 mm 1 18 Square 30 mm 1 18 Number holes sq meter with single spiked roller 990 990 Recommended tractor 20 HP with minimum lifting capacity of 450 kg 990 Ibs 30 HP with minimum lifting capacity of 550 kg 1212 lbs S
9. User manual and parts manual SPEEDSEED Model 1200 1600 2100 2400 Serial number Translation of the original operating instructions ATTENTION REDEXIM Kwekerijweg 8 3709 JA Zeist the Netherlands T 31 30 6933227 F 31 30 6933228 E verti drain redexim com www redexim com QS eV TO ENSURE SAFE USE OF THIS MACHINE AND TO BE ABLE TO ACHIEVE THE BEST RESULTS IT IS OF MAJOR IMPORTANCE TO READ THIS USER MANUAL THOROUGHLY BEFORE USING THE SPEEDSEED 1015 English 924 120 200 FOREWORD Congratulations with the purchase of your Speedseed To ensure long and safe use of this Speedseed it is of major importance to all users to read and understand this user manual Operation of this machine is not safe without full knowledge of the content of the manual The Speedseed is not an independently operating machine The user is responsible for using the appropriate tractor The user must also check the tractor Speedseed combination for safety aspects such as noise level adequate user instructions and any risks The Speedseed is solely intended for use on lawns and other areas where grass could grow On the next page you will first find the general safety instructions Every user must know and apply them After this a registration card is included This card should be returned for handling any future claims This user manual offers many instructions numbered in sequence This sequence should be observed An asteris
10. e to 0 3 mm 0 012 Turn roller 1 half a turn and measure the slit opening If necessary adjust it to 0 3 mm 0 012 by turning bolt 4 in or out Tighten the lock nuts 3 The split opening should be equal along the entire width of the roller The slit opening must have the same size as the smallest seed part This opening is default set to 0 3 mm 15 1 ADJUSTING THE SEED TRAY SCRAPER When the seeding tray is spoiling seed the scraper setting may be incorrect To adjust this proceed as follows see fig 9 1 Loosen bolts and nuts 6 2 Move scraper 5 up or down until the correct setting has been obtained 3 Re tighten the bolts and nuts 6 The distance between roller 1 and scraper 5 is default set to 0 8 mm and should be equally set along the entire width of the roller 16 15 2 SPREADING TEST If the seeding device needs recalibration for a certain seed type or if it must be checked for proper operation in accordance with the seed table see section 5 0 Tab 1 a spreading test is to be carried out This is done as follows see fig 10 qo Speedseed ous Fig 10 Place the machine safely on the support legs on a level surface P Lock the machine to prevent it from moving First of all check the seeding slit opening for correct setting see section 15 0 Put the seed that is to be calibrated into the seed tray 1 and spread it equally over the tray Place a co
11. eed tray capacity 168 litres 5 9 cu ft 225 litres 7 9 cu ft Maximum capacity theoretically at maximum speed 12 km h 7 5 mph and single passage 14175 m 152523 ft 18900 m 203438 ft Seeding density per 100 m 1076 4 ft Fine seed 0 2 2 8 kg 0 44 6 17 lbs adjustable in 10 steps Coarse seed 0 2 4 kg 0 44 8 82 Ibs adjustable in 10 steps Fine seed 0 2 2 8 kg 0 44 6 17 Ibs adjustable in 10 steps Coarse seed 0 2 4 kg 0 44 8 82 lbs adjustable in 10 steps Shipping dimensions LxWxH 1500 x 870 x 1070 mm 75x34x42 LxWxH 1900 x 870 x 1070 mm 75x34x42 Three point connection Three point CAT 1 2 Three point CAT 1 2 Lubricant EP 2 EP 2 Tyre pressure 1 2 bar 14 5 29 psi 1 2 bar 14 5 29 psi Standard parts 5 gear sets for adjusting the seeding density Manual container Seed tray with sight glass Seeding wheel adjusting to the area 5 gear sets for adjusting the seeding density Manual container Seed tray with sight glass Seeding wheel adjusting to the area Option Set of spikes for back roller Set of spikes for back roller Model 2100 2400 Working width 2 1 m 47 2 2 4 m 62 2 Working depth 5 mm 20 mm 0 19 0 78 5 mm 20 mm 0 19 0 78 Seeding speed Up to 12 km h 7 5 mph Up to 12 km h 7 5 mph
12. he tractor when travelling on public roads Check the national traffic rules In view of the weight of the Speedseed a maximum speed of 20 km h 12 4 mph should be observed while driving in open fields with the machine raised Higher speeds may endanger the driver and or other people and even damage the machine T When the machine is in the raised position at least 2096 of the weight of the tractor should be supported by the front axle 7 0 DRIVING SPEED The driving speed is limited to 12 km h 7 5 mph Higher speeds are not recommended in view of excessive wear and damage that may occur to the machine due to for example rocks in the ground 8 0 GENERAL REMARKS ON THE USE OF THE SPEEDSEED Some general remarks tips on the use of the Speedseed A field can be tilled 2 or 3 times in different directions in order to obtain a higher seeding density Do not make sharp turns When hitting a hard object in the soil the spike elements may be burred damaged Try to file burrs away or replace the spike element NEVER drive backwards while the running wheel is on the ground 9 0 OPERATING THE SPEEDSEED Before using the Speedseed in the field check the following 1 Are there any loose objects in the field Remove these first 2 Are there any slopes The maximum slope this machine can work on is 20 degrees Always work downhill 3 Does the ground contain hard objects If so use the Speedseed at a low speed and adjust the wo
13. k indicates a safety instruction An 9 indicates a tip and or note All information and technical specifications provided at the moment that this document is published are the most recent ones Design specifications may be changed without prior notice This document is a translation of the original operating instructions Upon request the original operating instructions are available in Dutch GUARANTEE CONDITIONS THIS SPEEDSEED COMES WITH A GUARANTEE FOR DEFECTIVE MATERIALS THIS GUARANTEE IS VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASING DATE SPEEDSEED GUARANTEES ARE SUBJECT TO THE GENERAL CONDITIONS FOR SUPPLY OF PLANT AND MACHINERY FOR EXPORT NUMBER 188 PUBLISHED UNDER THE AUSPICES OF THE UNITED NATIONS ECONOMIC COMMISSION FOR EUROPE REGISTRATION CARD For your own information please complete the table below Serial number of machine Dealer name Purchasing date Remarks H SAFETY INSTRUCTIONS Fig 1 may lead to injury and or damage to the The design of the Speedseed allows for safe use However this is only possible if the user fully observes the safety instructions given in this manual Read and understand Fig 1 the manual before starting to use the Speedseed Not using the machine as described in the manual Speedseed The Speedseed is solely intended for tilling lawns or areas where grass should grow Any other use is considered to be incorrect use
14. llecting back under the machine to collect the seed Turn the wheel 2 13 full rotations counterclockwise Weigh the seed that is collected and multiply this by 5 09 881200 Weigh the seed that is collected and multiply this by 4 08 881600 Weigh the seed that is collected and multiply this by 2 91 881600 Weigh the seed that is collected and multiply this by 2 55 881600 The result is the weight of the seed that is seeded per kg 100m Ibs 1000 ft Compare the results with Tab 1 section 5 0 and do another spreading test if necessary If the results of the spreading test do not reasonably match the calibration values check the seeding slit opening and adjust this if necessary see section 15 0 17 16 1 OPTION SPIKES ON REAR ROLLER It is possible to mount spikes on the second roller Article number for this is 224 120 000 for the speedseed 1200 224 160 002 for the speedseed 1600 224 210 000 for the speedseed 2100 224 240 000 for the speedseed 2400 For mounting the spikes follow the next rulles Take care that when you assemble the spikes the cable and crane can lift at least 600 kg Crawl never under the machine and take care of the sharp points on the spikes akWND O 7 8 9 Be sure the machine is blocked against moving away Lif the machine at the back side from the ground Demount the rear cover plate 2 Demount the rear roller 1 Demount the scraper 3 store this
15. ons have been made to the Speedseed the present CE certificate becomes null and void and the person who made the modifications should himself make sure a new CE certificate is granted Inspect the Speedseed for loose bolts nuts parts before each use If present inspect the hydraulic hoses regularly and replace them if they are damaged or show signs of wear The replacement hoses must meet the manufacturer s technical specifications Always relieve the pressure from the hydraulic installation if present before carrying out any work on it NEVER use de Speedseed when protective covers and safety stickers are missing NEVER crawl under the Speedseed Tilt the Overseeder if you need to have access to the bottom NEVER step off the tractor while the engine is still running When carrying out maintenance activities adjustments or repairs make sure the Speedseed is locked to prevent it from sinking riding sliding away When carrying out any maintenance activities adjustments or repairs always switch off the tractor engine first remove the tractor key from the ignition and disconnect the PTO Fig 2 Fig 2 When carrying out any maintenance or repair activities make sure to use original Speedseed parts only This will ensure safety for the machine and its user Only authorised technical personnel may carry out adjustments and repairs to the Overseeder Keep an overview of repairs In addition to the instruc
16. ray Set the scraper closer to the Distance between the scraper seeding roller and the seeding roller is too large Tape up glue The adjustment plate of the seeding slit on the side is leaking The machine does not reach _ Tractor tensioning is too low Put drawing arms into a higher the required depth hole Ground is too hard Aerate irrigate Top rod is incorrectly adjusted Correctly adjust the top rod Too much dead leaves and Remove the dead leaves and roots in the top layer of the roots field Not enough weight Add weight Drive wheel is slipping Ground is too wet Postpone the tilling Tyre pressure is too low Inflate Dose measuring roller is dirty Clean the dose measuring roller Chain drive is rigid Lubricate 13 0 EU CERTIFICATE We Redexim BV Utrechtseweg 127 3702 AC Zeist The Netherlands declare entirely on our own responsibility that the product SPEEDSEED MODEL 1200 1600 2100 2400 WITH MACHINE NUMBER AS INDICATED ON THE MACHINE AND IN THIS MANUAL to which this declaration relates is according to the stipulation of the 2006 42 EC directive for machines Zeist 01 10 09 A C Bos Manager Operations amp Logistics Redexim Holland E 14 14 0 MAINTENANCE Time schedule Check point lubricating point Method Before each use Check for loose bolts nuts Presence and legibility of safety stickers Fig 5 Tighten the loose bolts nuts with the correc
17. rking depth 4 Is there any danger of flying objects such as golf balls which may distract the attention of the driver If so do NOT use the Speedseed Is there any danger of sinking or sliding away If so postpone the work If the soil is frozen or very wet the work should be postponed until the conditions are more favourable mo 10 0 STARTING STOPPING PROCEDURE Before starting the seeding check the machine for the following points While checking the machine tractor combination must be fully locked to prevent it from driving sliding sinking away The tractor engine must be switched off e Check the seeding elements for damage and repair if necessary e Check the seed spreading by rotating the running wheel 1 time counterclockwise 12 e Check if the drive is running smoothly e Check the tyre pressure START SEEDING The starting procedure is VERY important If this procedure is not followed exactly as described below serious damage may occur to the machine The procedure is as follows Put the seed in the seed tray Set the required seed quantity using the change wheels see section 5 0 Drive to the place where you want to start Start with a driving speed of about 3 km h 1 9 mph While driving lower the machine carefully and in a controlled way until the spike elements are cutting the ground If necessary stop the spike elementsin the ground to adjust the working depth see section 4 0 Oo RON 9
18. t torque Replace if damaged or missing After first 20 operating hours new or repaired Grease the roller bearings Check for loose bolts nuts Grease the drive chains Use EP 2 lubricating grease Tighten the loose bolts nuts with the correct torque Use a chain spray After every 100 operating hours Grease the roller bearings Check for loose bolts nuts Grease the drive chains Check the tension of the drive chains Check the seeding roller for dirt damage Check the seeding slit opening Check the seed quantity Check the spike elements for damage Use EP 2 lubricating grease Tighten the loose bolts nuts with the correct torque Use a chain spray Tension the tensioners of the drive chains Clean the seeding roller or replace it if necessary Adjust the seeding slit if necessary Carry out a spreading test Repair or replace if necessary 15 15 0 ADJUSTING THE SEEDING SLIT OPENING Fig 9 If the seed production does not correspond with the table the seeding slit may need adjustment This is done as follows see fig 9 1 2 3 4 5 Loosen all lock nuts 3 Adjust bolt 4 such that a feeler gauge of 0 3 mm 0 012 can be slit just between the roller 1 and the adjustment plate Check all bolts 4 and calibrate the slit opening between roller 1 and adjustment plate 2 along the entire width of the machin
19. tions in this user manual the generally applicable regulations with respect to safety and working conditions must be observed For use on public roads the relevant traffic rules also apply Transporting persons is not permitted Do not use the Speedseed when it is dark during heavy rain storms or on slopes with a gradient of more than 20 degrees Before starting to work all persons operating the Speedseed must be familiar with all its functions and controls Connect the Speedseed to the vehicle that will pull it exactly according to the instructions Danger of injury Before driving off make sure you have a clear view both nearby and far away On both sides of the Speedseed safety stickers Fig 3 4 5 have been applied to the sideboards and to the back cover Fig 6 showing these warnings Make sure these safety stickers are always clearly visible and legible Replace them if they are damaged During operation make sure there are NO persons in the danger area of the Speedseed to prevent them from getting injured by moving parts Fig 3 AN fig 3 fig 4 Keep a distance of at least 4 metres Fig 4 Be aware of the maximun lifting capacity of the towing vehicle Wear suitable clothing Wear sturdy shoes with a steel tip wear long trousers do up long hair and wear no loose clothing gt Def e A 7 Location of safety stickers Fig 5 CO
Download Pdf Manuals
Related Search