dassrl - pro
Contents
1. Doc N MO5 EN Page 12 PLATE WASHER Rey 62 USER MANUAL Date 27 05 2004 3 1 3 2 3 3 3 4 SECTION 3 PACKAGING TRANSPORT AND STORAGE GENERAL WARNINGS Before starting with the packaging operations the machine has to be put out of service as well as before the transportation and storage the instructions as indicated in Section 8 of this manual have to be properly observed The instrument has been used with samples potentially infected urine human sera etc that could have been caused INFECTED CONTAMINATIONS General safety warnings about biological substances potentially infected have to be observed Before putting the instrument out of service IT HAS TO BE DISINFECTED Before transportation or storage of the instrument draw up the minutes of declaration of disinfection dated and signed by a qualified person PACKAGING Packaging is needed anytime the instrument has to be transported or shipped by courier or other means To pack the instrument follow the instructions as below described put the instrument into the original packaging box or into a suitable cardboard box in this case the instrument has to be properly protected by plastic protective material mark the package with address instrument identification and warning labels OUT OF SERVICE MATERIAL Biological substances potentially infected INSTRUMENT TRANSPORTATION The transportation of the instrument when unpacked must be limited2. To clean the micro titer plate location use a water soaked cloth with 0 5 Sodium Hypoclorite Make sure not to leave any loose threads The room and desk where the instrument is placed have to be always clean remove any dirt Warning cleaning the instrument do not use alcohol or similar solutions When cleaning don t let electric parts connectors etc get wet If necessary before turning the instrument on dry them out 7 1 2 Inspection and controls It is advisable to check periodically all the instrument parts PLATE WASHER USER MANUAL Doc N MO5 EN Page 25 Rev 02 Date 27 05 2004 fui 7 3 TROUBLESHOOTING DIAGNOSIS Some troubles that might occur during the instrument functioning as well as the specific remedy are shown in the following table TROUBLE PROBABLE CAUSE REMEDY The instrument doesn t go The power source is faulty Incomprehensible The start has gone wrong messages are displayed MEMORY ERROR is displayed data are missing MISSING CALIBR volume is not defined The instrument doesn t Incorrect connection dialogue with the PC The instrument sends to the PC wrong messages different from the one of the communication program REPAIRS Only simple repairs are allowed to the operator It means that some memorized It means that the dispensation The instrument transmission is Check the power cord and source Check the fuses if necessary replace them
3. L gt lt Manifold DISPENSER gt E Velve A gt ASPIRATOR I ce WASTE WASH 1 Liters 1 Liters BOTTLE BOTTLE TITER PLATE MIC RO fig 2 6 Doc N MO5 EN Page 11 PLATE WASHER Bane USER MANUAL Date 27 05 2004 2 5 INSTRUMENT TECHNICAL DATA Display Alphanumerical 2 lines 16 characters LCD Keypad 17 keys two of which with variable functions to guide the user Program setting up washing volume delay time before starting the washing cycle washing cycle delay between strips strip selection to start with washing number of strips to be washed number of washing cycles for each strip number of the plate washing cycles Final aspiration for the single strip Plate washing aspiration starting Program memorization storing capability of 100 programs RS232 serial output 9600 baud 1 start 8 data 1 stop no parity XON XOFF protocol Electrical power requirement Standard 230 VAC 50 Hz Optional 115 VAC 60 Hz Power consumption 80W max Operating conditions temperature from 10 to 35 C relative Humidity up to 85 Shelf condition temperature from 10 C up to 60 C relative humidity up to 85 Dimensions width 34 mm height 18 5 mm depth 36 mm Weight 13 Kg INSTRUMENT EQUIPMENT e User s manual e Three 1 liter bottles for Wash and Waste and Cleaner e Tubingkit e AC power Cable e Fuseskit e 1 Dust cover Additional accessories optional e PC cable connection
4. Plate Washer USER MANUAL This manual contains DAS reserved information All rights reserved Unauthorized copying of this manual or part of it is prohibited Viale Tivoli Km 18 642 00018 Palombara Sabina Roma Italy d as Tel 39 0774 66840 0774 637070 Fax 0774 634039 sr E mail info dasitaly com http www dasitaly com Doc N MO5 EN Page 3 PLATE WASHER a USER MANUAL Date 27 05 2004 Causal Date Revision description Emissione Rev 00 04 02 2002 New edition issue Rev 01 19 07 02 Da A1 a A2 Rev 02 27 05 2004 New CE Declaration Doc N MO5 EN Page 4 PLATE WASHER Rev 02 USER MANUAL Date 27 05 2004 CONTENTS INTRODUCTION dadas 5 Dl DESCRIPTION lg i ia aa 5 02 gt E Si il lai dii 5 0 3 CE CONFORME oe oid ARA aaa 6 SECTION 1 GENERAL SAFETY WARNINGS ncsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssessssssssnusssssssssssseee 7 1 1 DANGER WARNING SYMBOLS 0 enano 7 1 2 INTENDED USE OF THE INSTRUMENT anne 7 13 USE OF THE INSTRUMENT illa SECTION 2 GENERAL INFORMATION 2 1 INSTRUMENT DESCRIPTION PURPOSE AND FEATURES 8 2 3 INSTRUMENT DESCRIPTION es 8 2 4 INSTRUMENT FUNCTIONING PRINCIPLE 10 2 5 INSTRUMENT TECHNICAL DATA as 11 SECTION 3 PACKAGING TRANSPORT AND STORAGE oesssssssssssssssssssssssssssssssssssssssssssssssssssssssssssessssseee 12 3 1 GENERAL MARN ER i 12 3 PACKAGING soo a es rh lhl 12 3 3 I
5. 336 EC regarding Electromagnetic Compatibility The below harmonized standard specifications have been applied Quality system EN ISO 9001 2000 Quality management systems Risk analysis EN 14971 2000 Application of risk management to medical devices Safety EN 61010 1 1997 Electrical equipment safety requirements for measurement control and laboratory use Part 1 General requirements Electromagnetic Compatibility EN 61326 1 1998 Electrical equipment for measurement control and laboratory use EMC requirements Part 1 General requirements Doc N MO5 EN Page 7 PLATE WASHER Bane USER MANUAL Date 27 05 2004 1 1 1 2 1 3 SECTION 1 GENERAL SAFETY WARNINGS DANGER WARNING SYMBOLS In this manual the following symbols are to remind the user of the safety rules This is a symbol of generic DANGER It means that serious dangers might occur to the operator if the described precautions are not fulfilled This is a symbol of high electrical voltage by touching parts reporting this label life endanger might occur Parts reporting this label can be handled only by qualified operators after having unplugged the instrument This symbol indicates that the instrument makes use of chemical reagents and other dangerous corrosive irritant and harmful CHEMICAL SUBSTANCES which can cause damages to people and things When this label is found pay attention to the producer s r
6. Switch off the instrument and after while switch on again In case of failure repetition call for Technical Assistance Call for Technical Assistance Calibrate the dispensation see par 5 3 3 Check the cable connection be sure of the serial port Check the program setting for the utilized serial port Check the data transmission speed of the instrument and the one of the program are the same 9600 baud In case of complex breakdowns or defects might occur to the instrument qualified technical interventions are required REPAIR extraordinary maintenance has to be carried out see Section 1 only by e Authorized Technical Service licensed center which can operate on request or under assistance contract by Specialized Technicians using original spare parts Transformations or modifications of the instrument are not allowed The user is liable for any instrument improper use or modification and for the deriving consequences Doc N MO5 EN Page 26 PLATE WASHER Rev 02 USER MANUAL Date 27 05 2004 8 1 8 1 1 SECTION 8 DISINFECTION AND PUT OUT OF SERVICE INSTRUMENT DISINFECTION The instrument involves the handling of samples which can be infected urine and human serum and positive controls In this condition INFECTIONS or CONTAMINATION might occur Every part and accessory of the instrument must be considered potentially infected Carefully disinfect the instrument before transporting it to another plac
7. distilled water and then prime at least two times PRIME ON 5 8 DISPLAYED MESSAGES In case of failure the instrument is able to display the below messages See Section 8 for the needed operations MEMORY ERROR This message means that some memorized data are missing MISSING CALIBR This message means that instrument is not operative as the dispensation volume is not defined Doc N MO5 EN Page 23 PLATE WASHER Rev 02 USER MANUAL Date 27 05 2004 SECTION 6 PC CONNECTION 6 1 INTRODUCTION The instrument is equipped with an RS232 serial port for PC connection A cable and software are optionally available to link the instrument to PC IBM or compatible in order to print transfer and record the acquired data To use different communication programs be sure that the following parameters are set 8bit 9600 baud rate no parity stop bit 6 2 CONNECTION PLATE WASHER COMPUTER Use a cable to link the instrument to the RS232 serial port Make sure of its compatibility as following e A9 pins connector is available at the rear of the instrument see fig 6 1 e Two serial ports are located on the PC usually a 9 pins or a 25 pins male connector crt a BAIA fo fs oo 2 Tx 3 Rx 5 GND FUSES 1 A fig 6 1 RS232 serial port location Doc N MO5 EN Page 24 PLATE WASHER Ro USER MANUAL Date 27 05 2004 SECTION 7 MAINTENANCE AND CONTROLS Only qualified
8. or the internal rules of the laboratory if the instrument has to be transported or stored enclose the disinfection Certificate dated and signed by a qualified operator Momentary stocking Disactivate the instrument and label it with warning signals of OUT OF SERVICE see Sec 3 DEMOLISHING PROCEDURE Dismantle the instrument parts that connect the elements according to their chemical nature Start demolishing procedure respecting the local current laws and regulations
9. within the room where it is used avoiding damaging bumping When shipped or transported the instrument has to be provided with DISINFECTION DECLARATION CERTIFICATE see Sec 8 of this manual STORAGE OF THE INSTRUMENT Before storing the instrument for a long period pack it carefully as described above Relative humidity has to be less than 85 and temperature between 0 C and 50 The instrument disinfection declaration has to be labeled on the packaging before storing it see Sec 8 of this manual Doc N MO5 EN Page 13 PLATE WASHER Uds USER MANUAL Date 27 05 2004 SECTION 4 INSTALLATION AND START UP INSTRUCTIONS MN Installing and setting up the instrument the safety warnings and general rules described in Section 1 must be observed 4 1 PLACING THE INSTRUMENT The instrument has to be placed on a leveled bench Room temperature has to be between 15 and 32 C with a relative humidity below 80 protect it from direct sunshine 4 2 POWER SUPPLY Once the instrument has been placed plug it to a power of 220VAC by the supplied cable FUSES 1A fig 4 1 Warning make sure that the electrical power is the one as requested and indicated on the identification label of the instrument 230V or 115 V Warning make sure that the fuses correspond to the ones indicated on the identification label of the instrument and in the manual 230 VAC mains 2 quickfuses 1A 115 VAC mains 2 quick fuses 2A
10. GRAM number list programs F1 F2 PROGRAM NO ENTER 001 NAME XXXXXX next previous Pressing set is possible ser to show the parameter F1 of the program To change the parameters of the program following Y the steps of par 5 4 001 NAME XXXXXX show change Follow NEW PROGRAM SETUP o P 20 O PLATE WASHER Boe N MOREN age USER MANUAL Date 27 05 2004 5 6 PROGRAM RUN 5 6 1 GENERAL FLOW DIAGRAM START set up yes progr modification RUN o P 21 PLATE WASHER SO i USER MANUAL Date 27 05 2004 5 6 2 PROGRAM START UP SELECT SELECT PROGRAM memory new FI F2 PROGRAM NO F1 F2 SELECT THE PROGRAM FIRST POSITION STRIP gt gt POSITION STRIP initial nn ERS NUMBER STRIP NUMBER OF STRIP TO WASH ESC FI F2 ENTER INSERT PLATE run al ESC Doc N MO5 EN Page 22 PLATE WASHER Rey 62 USER MANUAL Date 27 05 2004 5 7 PRIME From the main Menu it is possible to process a complete prime at each working starting of the machine use washing solution SELECT Washing Prime ae ag In order to wash the hydraulic circuit the prime command has to be used at the and of each session to perform the above change the wash solution with
11. NSTRUMENT TRANSPORTATION is 12 3 4 STORAGE OF THE INSTRUMENT annie 12 SECTION 4 INSTALLATION AND START UP INSTRUCTIONS vsssscsssssssssssssssccsssssssssssssssssssssssssssssesssees 13 41 PLACING THE INSTRUMENT ns 13 AO POWERSUPPLN inline el a 13 SECTION 5 HOW TO USE PLATE WASHER onvssssssssssssssssssssssssssssssssssssssusssssssssssssssssssssssssssssssssnssssssssssssseee 14 5 INTRODUCHON selle aa ati 14 5 2 SWITCHING THE INSTRUMENT ON ans 14 5 4 NEW PROGRAM SET UP ains 17 55 PROGRAM MODIFICATION sl allora aa 19 56 PROGRAM RUN fc ae a 20 SI PRIME iii 22 58 DISPLAYED MESSAGES cinica 22 SECTION 6 PO CONNECTION iii 23 Gis INPRODUCHON OO 23 6 2 CONNECTION PLATE WASHER COMPUTER ocio coran 23 SECTION 7 MAINTENANCE AND CONTROLS oosssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssusussssssssssssssens 24 7 1 PREVENTIVE MAINTENANCE AND CONTROLS coreanas 24 7 2 TROUBLESHOOTING DIAGNOSIS ais 25 TG REPAIR Seek oe lel I A A ri 25 SECTION 8 DISINFECTION AND PUT OUT OF SERVICE osssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssees 26 8 1 INSTRUMENT DISINFECTION is 26 8 2 PUT THE INSTRUMENT OUT OF SERVICE csi 27 8 3 DEMOLISHING PROCEDURE iii 27 Doc N MO5 EN Page 5 0 1 0 2 0 2 1 0 2 2 PLATE WASHER Rev 02 USER MANUAL Date 27 05 2004 INTRODUCTION DESCRIPTION This manual provides the operator with all the n
12. affects all the mechanical and electrical parts It is granted only for a proper installation use and maintenance in compliance with the given instructions in this manual contained According to this warranty DAS commits itself to repairing or replacing all the parts which show off to be defective from the beginning The warranty does not include any responsibility for direct or indirect personal and material damages caused by improper use and maintenance of the instrument All parts that are subject to deterioration because of their specific use are excluded from the warranty Due to a misuse of the instrument the above mentioned warranty does not include if requested the travel and labor hour expenses as well as all the accommodation expenses Asking for Service DAS is always at the Customer s disposal for any kind of information about use maintenance installation etc When asking for service please refer to this manual pointing out the data reported on the identification label registration number and production year Only qualified Technicians are entitled to fix the instrument ordinary maintenance should be carried out by the user as described in this manual DAS Technical Service or a licensed Service Center with Specialized Technicians with suitable instrumentation and original spare parts are always available for extraordinary maintenance repair under a yearly assistance contract or on specific demand Ordering the spare parts Part
13. e or before starting any maintenance Before sending back the instrument it has to be carefully disinfected Fill in a disinfection certificate and enclose it with the instrument If the certificate is missing the customs officers or your service center can refuse the instrument Disinfection Process Prior to any repair or maintenance intervention and before transporting the instrument a disinfection is necessary by using wide band solutions Warning USE LABORATORY PROTECTIVE CLOTHES DISPOSABLE GLOVES AND GLASSES WHILE DISINFECTING THE INSTRUMENT Use one of the following wide band solutions gt Aseptisol Manufacturer Bode Chemie Amburg gt Germocid Plus Manufacturer Germo S p a Milano gt Lysetol Manufacturer Sch lke amp Mayr Ges m b H If the above solutions are not available use other wide band disinfectant solutions Use the solution only for the instrument surface Wear disposable gloves protective glasses and suitable clothes 2 Prepare an autoclave bag for the disposable items used for the disinfection and label the bag with an autoclave band mark 3 Unplug the instrument in order to avoid explosions x 4 Remove all the accessories and disinfect the ones which have to be sent with the instrument 5 Spray the disinfectant solution on the instrument surface or use a cloth or paper soaked in a disinfectant solution 6 Leave the solution on the instrument for 10 minutes and repeat the treatment from
14. ecessary instructions for a safety suitable use as well as the instrument maintenance recommendations Manual content introduction warranty information Service maintenance and the CE mark conformity declaration section 1 general safety warnings section 2 general information such as the producer data technical data instrument performances etc section 3 packaging transport and storage instructions section 4 installation and start up section 5 operating instructions section 6 PC connection instructions section 7 the user s periodic maintenance and checking the trouble shooting at user s level and the repair policy section 8 instrument disinfection how to put it out of service and demolishing instructions section 9 spare parts list consumable material and accessories This manual is considered as a part of the instrument it has to be at the operator s hand as well as at the maintenance operator s availability For accurate installation use and maintenance please read the following instructions carefully In order to avoid damages to the instrument or to people carefully read the GENERAL SAFETY WARNINGS Section 1 describing the suitable operating procedures In case of breakdowns or any troubles with the instrument apply to the local Technical Service WARRANTY Each provided instrument is completely tested and guaranteed for twelve months from delivery The warranty
15. ecommendations This symbol indicates that the instrument involves the handling of samples which can be infected urine and human serum In this condition INFECTIONS or CONTAMINATION might occur Pay attention to the general safety warnings when in presence of such biological substances Use protective clothes gloves and glasses gt gt gt gt This symbol indicates that damages to the instrument and or its incorrect results could occur if the given warnings are not respected This symbol is to advise that the instrument or part of the manual which is particularly important has to be consulted INTENDED USE OF THE INSTRUMENT The instrument is designed to be used in the following working conditions e washing of micro titer plate e work at room temperature and humidity according to the specified data e do not power the instrument in a potentially explosive environment or at risk of fire The instrument has to be used as described in this manual Any other use has to be regarded as improper USE OF THE INSTRUMENT The instrument has to be used for the expected purposes and in perfect technical conditions by qualified personnel in working conditions and maintenance operations as described in this manual according to the safety rules This manual contains instructions for qualified operators e Qualified User has to make sure that environmental condition is suitable the installation is correct the use and maintenance are proper acco
16. enabled e ESC usually allows to go back to the previous menu NOTE SET and ENTER in particular menus can change their function as after explained By pressing SET button when in the initial menu fig 1 some instrument parameters can be modified In the succeeding phases use ESCAPE to go back to the initial menu use SET to go to the next menu 5 3 1 Language selection From the initial menu press SET button only once the LANGUAGE SELECTION menu is displayed LINGUA LANGUAGE After the selection the DELETE MEM MENU is displayed Change F1 F2 5 3 2 How to delete stored programs DELETE MEM menu allows to delete filed SET programs DELETE PROGRAMS gt SET All Num fe 3 DELETE PROGRAMS All ED FA F1 F2 SET SHAKING TEST When F1 key is pressed in order to avoid fortuitous mistakes a further confirmation before deleting all the filed programs is required y DELETE PROGRAMS ARE YOU SURE wae M PROG no nn yes no If F1 is pressed the identification number of the ES Pai programs to be deleted is required then press ENTER ENTER aA Before deleting the selected program a confirmation is required Then the menu DELETE PROGRAM is displayed again Go back to Go back to PROGRAM DELETE PROGRAMS DELETED menu menu Doc N MO5 EN Page 16 PLATE WASHER RA ia USER MANUAL Date 27 05 2004 5 3 3 S
17. et shaking SET SET SHAKING menu allows to set the shaking speed of the plate SI j ce SET SHAKING EE SPEED n from 1to 5 INSTRUMENT TEST ORD yFAN pF 2 ENTER Executes a test 3 sec long 5 3 4 Instrument test INSTRUMENT TEST INSTRUMENT TEST RUN RUN ae ise AI A A ED Press F1 to enter the Service function go back to language Y SELECT MENU SERVICE The instrument test has the following functions Plate to move the plate Aspirator to move the aspirator up and down Pump1 to run pump1 Pump2 to run pump2 Valve to open close valve Test on strip 1 to calibrated the dispenser PLATE WASHER USER MANUAL Doc N MO5 EN Page 17 Rev 02 Date 27 05 2004 TEST ON STRIP 1 SET A F2 VOLUME FACTOR XX A a ENTE sui SET THE LIQUID VOLUME Y DISPENSING LIQUID STRIP 1 ci FIOR REPEAT Gi A aoe Fi F2 5 4 NEW PROGRAM SET UP SELECT washing prime PT SELECT PROGRAM memory new ED Starting strip position nn ENTER Number of strip to wash nn Y Liquid vol nnn Plate management A CI au F1 F2 ENTER v Select wash or activate Go to the plate yv strip empty Follows in the next page DISPENSER CALIBRATION Press F1 to start the strip dispensation test Set the volume to be dispensed from 200 to 400ul in step
18. of 50pl Press Enter The dispensation take place on strip 1 After the dispensation a visual check has to be made on the plate to verify if the dispensation is correct use a pipette to verify the effective dispensed volume Eventually repeat the dispensation test If a correction is needed change the volume factor F2 Press Enter and repeated the test up to a satisfactory result Select washing pressing F1 Select a new program set up F2 Digit the starting strip position and press Enter if we set zero at this request it will always repeat before program execution and the number of the strip to wash will be set to zero Digit the number of strips to wash or activate and press Enter if we set zero at this request it will always repeat before program execution Set the desired liquid volume from 200ul to 400ul in step of 50ul or O and press Enter If the liquid volume is 0 the machine will perform only an aspiration of the plate Select a washing cycle or an activation cycle as needed pressing F1 or F2 Press Enter after the selection Doc N MO5 EN Page 18 PLATE WASHER Ro USER MANUAL Date 27 05 2004 PLATE ACTIVATION follows from previous page Time delay to asp nns en Set the time after witch the application cuni plate take place on all the plate ME PLATE WASH ca Set the time sec of liquid pe
19. personnel is entitled to carry out maintenance see Section 1 of this manual Carrying out the maintenance operations follow the general warnings as described in Section 1 of this manual as well as the below safety rules 7 1 PREVENTIVE MAINTENANCE AND CONTROLS Cleaning Daily and or at the end of each working session General inspection and checks At interval of 6 months As the instrument could be used in different conditions and terms maintenance has to be done according to the use of the instrument the period indicated on the above table has to be taken on account as an average After a long period of the instrument inactivity a general maintenance is required before using it again 7 1 1 Cleaning f This symbol indicates that the instrument makes use of chemical reagents and other dangerous corrosive A irritant and harmful CHEMICAL SUBSTANCES which can cause damages to people and things When this label is found pay attention to the producer s recommendations This symbol indicates that the instrument involves the handling of samples which can be infected urine and human serum In this condition INFECTIONS or CONTAMINATION might occur Pay attention to the general safety warnings when in presence of such biological substances Use protective clothes gloves and glasses After each working session clean the instrument carefully Use a water soaked cloth or light detergent to clean the instrument external parts
20. rding to the general safety rules as well as to the particular precautions described in the manual although he is not entitled to repair the instrument e Qualified Technician is entitled to maintain and fix the instrument according to the instructions received and using the original spare parts Alterations of the instrument are prohibited The user is liable for any instrument improper modification as well as the deriving consequences Should the machine need extraordinary maintenance ask for DAS Service or for licensed service centers The maintenance will be carried out by Specialized Technicians that will be able to fix the instrument using the original spare parts to replace the defective ones o P 8 PLATE WASHER ce een as USER MANUAL Date 27 05 2004 SECTION 2 GENERAL INFORMATION INSTRUMENT DESCRIPTION PURPOSE AND FEATURES PLATE WASHER is a microplate automated washer It can be programmed according to a specific protocol In a combination with a microplate reader can be useful to automatize the ELISA washing process The free program open system allows the operator to run any possible plate washing by setting up the wanted program through its in built keyboard INSTRUMENT DESCRIPTION Components of different views of the below pictured instrument Front view two lines by 16 characters display alphanumerical key pad Micro titer plate carriage Rear view power socket and switch RS232 outp
21. rmanence Y into the strip Press Enter EN Set the number washing cycle for the strip ENTER Press Enter y Strip empty emeen e Select F2 F2 if the strip has to be left empty or full after the washing cycle Press Emen Enter Y i Set the time delay sec between the washing cycle of one strip and the beginning of the washing cycle of the Y following strip Press Enter EN A Set the number of complete washing cycle for the plate Press Enter Set the time delay between a cycle and ae 1 the next one a Select plate empty or not at the end of the Y working cycle if the strips were full MN Set the incubation time before washing take place Press Enter Plate empty yes no tip emp Press F1 to save the parameters vs Lit Shaking selection if shaking is selected ET the plate will be shacked during preda incubation time at the selected shaking se A speed see par 5 3 3 ENTER Insert the name of the program using Y F1 F2 ae Press Enter to go to program RUN 2 Y ses lc GO TO THE FIRST EMPTY FREE POSITION Go to Program RUN Doc N MO5 EN Page 19 PLATE WASHER Rev 02 USER MANUAL Date 27 05 2004 5 5 PROGRAM MODIFICATION SELECT washing prime SELECT PROGRAM memory new ED Y Select the program by number or by the list of existent SELECT PRO
22. s subject to deterioration or defective which need to be replaced have to be requested as shown below Ordering the spare parts the following data are to be mentioned e customer s purchase order name and version of the instrument instrument code number part code number description of the part requested quantity e name and company address to deliver the ordered goods Replacing the parts the use of ORIGINAL SPARE PARTS guarantees the efficiency and a lasting instrument life o X P 6 PLATE WASHER a e i ni USER MANUAL Date 27 05 2004 0 3 CE CONFORMITY CE Declaration of conformity according to the 98 79 EC In Vitro Diagnostic medical devices Directive IVDD DAS s r l manufacturer of Plate Washer Automated microplate washer class of risk In Vitro Diagnostic Medical Devices declares that the mentioned system complies with the European Directive 98 79 EC IVDD The present conformity declaration is based upon the following requirements Quality Management System ISO 9001 2000 Working Procedures and Instructions for e Design process control e Manufacturing process control e Tests and Checks System documentation e Technical documents e Risk analysis e User manual e Service manual The Managing Director The instrument conforms to the following EC Directives including the last modifications 98 79 EC regarding in vitro diagnostic medical devices 73 23 EC regarding low voltage 89
23. the preceding point 7 Leave the solution on the instrument for 5 hours clean the instrument surface by a light detergent or water to eliminate any dirt or disinfectant solution Carefully dry the instrument 9 Put the instrument and its accessories into their original box 10 Wash and disinfect the hands by using a light detergent 11 Fill in a Disinfection Certificate and enclose it with the instrument 0 Doc N MO5 EN Page 27 PLATE WASHER Se USER MANUAL Date 27 05 2004 8 1 2 Disinfection certificate 8 2 8 2 1 8 3 The Disinfection certificate as shown below has to be filled in and enclosed with the instrument before shipping it for a maintenance service The certificate Has to be stuck on the instrument package Disinfection certificate Instrument Model S N We declare that o the instrument and its accessories never came in touch with dangerous biological substances o the instrument and its accessories have been disinfected and or decontaminated to eliminate every biological substance which could be dangerous for the staff Responsible name User Address Country Date Signature PUT THE INSTRUMENT OUT OF SERVICE At the end of the instrument operating life dispose of it taking in account the safety for people and environment Unplug the instrument and the PC If the instrument has been used carefully disinfect and clean it following the above instructions
24. ua Page 14 PLATE WASHER DIM i USER MANUAL Date 27 05 2004 SECTION 5 HOW TO USE PLATE WASHER 5 1 INTRODUCTION The flow diagram below indicates how the instrument is used Detailed information for each step can be found in the indicated paragraph Table 5 1 GENERAL FLOW DIAGRAM INITIAL MENU PRIME INSTRUMENT PROGRAM FUNCTION SET UP SET LANGUAGE DELETE MEMORY Y Y Y INSTRUMENT NEW PROGRAM PROG Mi MEMORY RUN PROGRAM 5 2 SWITCHING THE INSTRUMENT ON AN The safety warning and general rules described in Section 1 have to be observed when using the instrument When switched on the instrument automatically checks the functionality of its main parts it SELECT show the heading containing the instrument name the software revision it checks the plate Washing Prime carriage home position Then the initial menu is shown as in fig 1 Select one of the two options as shown on the display lower line Washer or Prime by pressing the function keys F1 or F2 JE 0 ENTER PAPER fig 5 1 Initial menu Doc N MO5 EN Page 15 PLATE WASHER Rev 02 USER MANUAL Date 27 05 2004 When this initial menu is displayed the SET button assume specific functions e SET button is to modify some parameters as specified in the SET menu chapter e When in this menu ENTER button usually it allows to enter data when required on the specific menu is not
25. ut connector identification label Keypad Micro titer plate carriage Front view RS232 Power soaket Identification label connector Doc N MO5 EN Page 9 PLATE WASHER aL USER MANUAL Date 27 05 2004 2 3 1 2 3 2 Display and keypad Press F1 or F2 keys to select one of the two functions displayed on the screen low line e Press SET key to modify some of the set parameters PLATE WASHER e g date and hour Washer Prime A e Press ESC key to go back to the preceding menu e Press ENTER key to enter the data when provided from the specific menu functions according to the specific menu as better specified E in the SECTION 5 of this manual 6 ES Cs Jo Jem ora fig 2 4 NOTE The keys SET and ENTER have different EN Micro titer plate carriage The instrument is provided with a micro titer plate carriage to move the micro titer plate towards the inside washer N XY ay Ae eee Neale XAO NON J K X MN NENE TOTNMUOOOU gt AA IO O AKA CONC AIA 5 NOOO VOODOO AIA DA A 1234567 8 9101112 fig 2 5 Doc N MO5 EN Page 10 PLATE WASHER Rev 02 USER MANUAL Date 27 05 2004 INSTRUMENT FUNCTIONING PRINCIPLE Below fig 2 6 is the diagram representing the main functional elements of the instrument 2 4 PP TA gg S gt WASTE PUMP
Download Pdf Manuals
Related Search