Home

Anywhere

1. 7 EE UM if tl DC O J ETHERNET PoE M VIDEO OUT ey AEM ied oa ia ON re uG CLASS 2 ONLY Audio Terminal IN Audio input terminal to connect microphone OUT Audio output terminal to connect speaker system Auto iris lens selector switch Select DC drive lens or Video drive lens with this switch Reset button You can reset all zones of the camera to default level pressing this button longer than 5 seconds with LED blinking Wait one minute after resetting the power before turning on any function of the camera RS 485 RS 485 is the adequate cable to connect to SRX 100B for pan tilt control 24 2 2 Section names and functions ALARM terminal Alarm signal input terminal I is to connect to the external sensing devices such as infrared sensor thermal sensor etc Alarm signal output terminal O is to connect to the external warning devices such as alarm light or siren etc ETHERNET The standard RJ 45 connecter is adequate to connect to 10 100 Mbps Ethernet Electrical power transfer via PoE IEEE 802 3af is available Orange colored LED blinking is the sign of successful data transmission of the camera in the network RESET LED You can reset all zones of the camera to default level pressing this button longer than 5 seconds with LED blinking POWER LED When you turn on the camera power LED flashes Power terminal A terminal i
2. 72 4 2 Using Administration page Item Description Blending Level Blending Level function is to determine masking transparency of excluded area in the range of 1 to 255 Level 255 is perfect transparent Masking Color Masking color can be selected among Grey Blue and Violet 73 Network Camera SNC 570 4 2 7 Record Using the SD Memory When Motion Detection Video Analytics or Sensor is detected you can save them Then if an Event is occurred you can also watch them iPOLIS Record Setup E a E Record Page TI SD Memory Used Size T p Network SD Memory Free Size fs Jm P Warning Message off o Overwrite a TB Privacy Analytics Detection Recording El Motion Detection Recording o O tex Sensor Detection Recording __ poo jann T Total Count 28 1 1 MotionDetection 2008 10 06 19 27 16 x 3 1 MotionDetection 2008 10 06 19 26 43 Q o 4 1 MotionDetection 2008 10 06 19 26 28 5 1 MotionDetection 2008 10 06 19 25 34 ee 6 1 MotonDetection 2008110106 19 25 00 E voona o 7 1 MotionDetection 2008 10 06 19 24 47 o 8 1 MotionDetection 2008 10106 19 24 31 eR system Reboot 9 1 MotionDetection 2008 10106 19 24 18 fo 10 1 MotionDetection 2008 10 06 19 24 04 Item Description SD Memory Size It shows total storage capacity of SD memory SD Memory Usin z y 9 It shows SD memory occupation Size SD Memory Free a Size ry It shows b
3. Selects the video quality You can still view uninterrupted video with the quality reduced if you use a low speed Internet connection Video FrameRate Defines how many frames the camera will transfer per second Video Channel Defines what video channel will be used by the camera Audio In Channel Determines whether to use an audio input channel for the camera Audio Out Channel Determines whether to use an audio output channel for the camera Max User Count Specifies how many users up to 20 can connect to the camera via the network Microphone Sensitivity Audio Amplifier You need to set the sensitivity to Low with an amplifier equipped microphone and to High with an amplifier free Microphone set it to low for line in signals Product Information Item Description Model Describe camera model Mac Address Describe MAC address of camera Camera Name Name each camera to identify multi cameras on the network Location Describe each camera location Description Describe more information of camera Memo Describe contact number of the camera operator 56 4 2 Using Administration page 4 2 4 Network Network Configuration menu Network Setup Network Configuration IP Address 192 168 ja aaa NetMask 255 255 255 o tan Gateway 192 p68 fa ft DNS1 6s 126
4. 63 2 DNS2 ues 126 63 2 xDSL UserName password DHCP Port DDNS Configuration Connection Port 4000 default 4000 HTTP Port default 80 FTP Port default 21 Use DDNS DDNS Server ID Password E Continuous Jpeg Image Transmission to FTP Server Jpeg CIFs Enable o FrameRate 1 Server Name Home Directory User ID User Password Streaming Engine RTSP TCP Enable RTP UDP Enable RTP Multicast Enable Multicast IP 224 o i Multicast Port 4000 Streaming Image Resolution D1 57 Network Camera SNC 570 Network Configuration You can select LAN interface for static IP configuration xDSL modem and DHCP for cable modem Item Description LAN Configure network assignment information of a camera connected to the local area network or to the static IP of xDSL modem xDSL For dynamic IP of xDSL enter ID and password of xDSL in the username box and password box DHCP For IP router or cable modem interface select DHCP Port DDNS Configuration Item Description Connection Connection port is to control communication with Port camera Default 4000 HTTP Port HTTP FTP port is to access to the camera web ETP Port page or to use FTP function 2 Default http 80 ftp 21 D
5. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEBLE PARTS INSIDE REFER SERVICING TO QUALIFIELD SERVICE PERSONNEL FCC Compliance Statement Caution Any changes or modification in construction of this device which are not expressly approved the party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which cause the user will be required to correct the interference at his own expense Network Camera SNC 570 Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end o
6. Create an ID of 4 to 12 characters in length containing letters A Z or numbers 0 9 You should have exactly same ID with the item product ID to log on DDNS online service Make sure the correct ID and click the item product ID You may not able to change the initial domain name 1D domain PASSWORD PASSWORD CHECK Choose Choose product category CLASSI CATION MODEL NUMBER Choose choose product model LOCATION Determine the location to install the system or camera Designate the installation location within 10 alphabet letters DESCRIPTION Describe product for management purpose Figure 6 Product Registration Confirm repetition certainly at domain registration Howe isrreuar AZ EAN iPOLiIS WHATIS POLIS PRODUCT DDNS SERVICE SUPPORT MY IPOLIS aeiae Ysien eck iirr MY IPOLIS Product List My IPOLIS gt Product List List of registered IPs E Current product list is displayed lf vanted productis notin thelist click Product Registration at the bottom g samsuna ocr wesse WO Mo Location View infomation Management 5 1 andyinon SNP 1000 The RITZ CARITON Seoul OFF are Se DOWNLOAD CENTER 2 andy3300 SNP a400 AMBASSADOR HOTEL OFF GR ows sence 2 arayss0 SNC 570 Lab OFF Eat Derete vy Product Registration PRIVACY LEGAL NOTICE CONTACT US OPYRIGHI 1996 2007 SAMSUNG
7. Please peel off about 2mm of the outer skin of the insulated conductor inside the lens cable Approx 2 mm 28 3 1 Lens Installation 3 Please remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug Lens Lens cable Pin No DC VIDEO fn No 1 Pin Damping Red power eC fy No 2Pin Damping NC White video signal No 3 Pig pa No 4 Pin Drive Black GND No 1 EE No 3 Pin Drive 4 Please replace the auto iris lens connection plug cover and take off the CCD protection cap and then attach the auto iris lens to the camera by screwing it in clockwise 5 Please insert the connection plug that is connected to the auto iris lens cable into the auto lens connector which is located on the side of the camera 6 Please set the lens selection switch located on the back of the camera to DC or VIDEO depending on the type of auto iris lens which is being used 29 Network Camera SNC 570 m When using a C Mount lens Please take off the CCD protection cap and attach the C Mount lens to the camera by screwing it in clockwise C Mount Adaptor sie m When using a CS Mount lens 1 Please attach the CS Mount lens to the camera by screwing it in clockwise C Mount DOr Protection cao A 2 Please attach the CS Mount lens to the camera by screwing it in clockwise 30 3 1 Lens Installati
8. Q Are you sure that you want reboot the system Cancel Click lt OK gt button to reboot server 88 Ch5 Howto Operate Camera Network Camera SNC 570 5 1 Setup MENU Setup Menu LENS DC VIDEO MANUAL eE SHUTTER AGC SENS UP RETURN ate ATW MANUAL BALANCE TAWG SET OUTDOOR INDOOR BACKLIGHT SORE LDLC WDR HLC SSNR ON OFF DAY NIGHT COLOR B W AUTO IMAGE FREEZE V REV H REV ADJUSTMENT D ZOOM SHARPNESS RETURN CAMTITLE SYNC MOTION DET SPECIAL PRIVACY DIS LANGUAGE RESET RETURN EXIT 90 5 2 How to Set Up Functions 5 2 How to Set Up Functions Use OSD button displayed on Web Viewer screen to set up functions Q OSD button is popped up in Web Viewer 1 Please press the lt SET gt button Main setup menu is displayed on the monitor screen Select the function using the UP or DOWN button gt ONDAN MAIN SETUP LENS DC EXPOSURE J WHITE BAL ATW BACKLIGHT OFF SSNR ON d DAY NIGHT AUTO IMAGE ADJ J SPECIAL J EXIT Change the status using the LEFT or RIGHT button 91 Network Camera SNC 570 2 Select a desired function using the Up and Down buttons e Place the cursor over a desired item 3 Set up a selected item by using the Left and Right buttons 4 To finish the setting select EXIT and press the SET but
9. right side of the monitor below options will appear 4 Preferences a P tuda RTP RTSP SDP demuxer using Live555 5 Input Codecs Mise RTP over RTSP TCE E amp Access filters Access module client port amp Audio codecs amp Demuxers Tunnel RTSP and RTP over HTTP amp ATP ATSP eau HTTP tunnel port amp Dump amp H24 8 MJPEG gt Matroska S MOD Dkasenna RTSP dialect amp MPC amp Playlist Caching value ms RTSP user name s Subtites RTSP password amp MPEG TS E amp Other codecs m AS Vidor ondare lt SD Bpr 68 4 2 Using Administration page Check the Use RTP over RTSP TCP Enter rtsp serverip mpeg4unicast in the RTSP URL and press lt OK gt button to connect to RTP TCP RTP Multicast connection Enter rtsp serverip mpeg4unicast in the RTSP URL to connect to multicast Fie Dsc e OUDP RTP OUDP RTP Multicast OHTTP HTTPS FTP MMS rtTsP URL rtsp 192 168 1 100 mpeg4multic Advanced options Stream Save it Caching Customize rtsp 192 168 1 100 mpeg4multicast X TCP configuration should be cleared again to execute RTP Multicast 69 Network Camera SNC 570 4 2 5 Video Analytics The Analytics feature compares the current screen against the one at the time of clicking on Set button and marks changed areas It can detect up to 5 areas Video Analytics Setup video Analytics
10. 2 Section names and functions 2 2 Section names and functions 2 2 1 Front Lens cap Lens cap should be placed until the lens mounted C Mount lens adapter Mount the C Mount lens on this adapter CS Mount lens adaptor Replace the C Mount lens adapter with this Back Focus adjustment lever Adjust focal length with this 21 Network Camera SNC 570 2 2 2 Side Auto Iris Connector The camera controls the iris lens via this connector SD MEMORY CARD SLOT Insert the SD memory card here SNC 570 is designed to accept SD card only A E not for MMC Do not insert the card in reverse Caution otherwise the slot can be damaged Only 128MB 2GB SD cards can be used while 4GB SDHC is supported We recommend the FAT32 format 22 2 2 Section names and functions 2 2 3 Bottom Tripod Mounting seat Bolt down the tripod here using screws specified as r below 1 4 20UNC 20THREAD L 4 5 mm 0 2 mm ISO Standard or 0 197 ASA Standard r X Tripod mounting module can be relocated to the top surface In this case use the screws shorter than 4 mm otherwise the camera can be damaged seriously This camera package does not include the A r mounting bracket Please refer to the user s Caution manual for installation of the mounting bracket 23 Network Camera SNC 570 2 2 4 Back ho
11. Configuration Video Analytics Enable Transition Time 3sec v Reset Time Sensitivity Item Description Video Analytics Determines whether to use Video Analytics Enable ai Shows the period of time maintaining a changed Mransition Time screen for Detection 3 6 9 12 or 15 sec 70 4 2 Using Administration page Item Description This is the time needed to convert the current Reset Time screen to the standard one 30 or 60 sec 10 min 30 min or Stable Ratio Determines whether to detect an object depending on the size 1 Low 5 High When Video Analytics is enabled the motion A A detection feature is automatically disabled Caution Depending on your system the Video Analytics feature may not function properly 71 Network Camera SNC 570 4 2 6 Privacy For privacy protection you can specify areas to hide Privacy Setu o Privacy Zone Configuration Grid Display Select Area Privacy Enable Blending Level Masking Color Select All Deselect 1 MAX 255 MIN Grey Set Item Description Grid Display Auto hide mode of screen split tool to select area In the process of Privacy configuration press lt Select All gt button to configure the whole screen or Select Area press lt Deselect gt button to cancel the configured screen area Privacy Determine use of Privacy function Enable
12. DC Iris lens rather than manual lens is recommended Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC performance In a dark environment the HLC is only activated when a high light that is larger than a certain area is present The HLC is not activated in light or overly dark conditions 5 2 5 SSNR This function reduces environment 1 102 the background noise in a low luminance When the SETUP menu screen is displayed select SSNR by using the Up and Down buttons so that the arrow indicates SSNR 5 2 How to Set Up Functions v OMNAOARWN MAIN SETUP LENS DC J EXPOSURE J WHITE BAL ATW BACKLIGHT OFF SSNR ON J DAY NIGHT AUTO J IMAGE ADJ J SPECIAL J EXIT 2 Select a desired mode using the Left and Right buttons OFF Deactivates SSNR Noise is not reduced ON Activates SSNR so that noise is reduced 3 Set the SSNR mode to ON and press the SET button Then you can adjust the noise reduction level Press SET to Return A ution You cannot set the SSNR to ON or OFF when the AGC mode of the EXPOSURE menu is OFF When adjusting the noise reduction level of the SSNR mode remember that the higher the level set the more the noise level will be reduced but that after image may also occur 103 Network Camera
13. DDNS SERVICE SUPPORT MY IPOLIS MY IPOLIS 6 Product List My IPOLIS gt Product List List ofregistered IPs E Curent product list is displayed S wanted productis notin the ist cick Product Registration at the bottom g smanccevwraste Wo D Model Location Status View Infomation Management 1 andylO0 SNP 1000 The RITZ CARITON Seoul ON view V DOWNLOAD CENTER a 2 andy330 SNP 3300 AMBASSADOR HOTEL OFF anm ran perte PX oons serv 3 andy550 SNC 570 Lab OFF arm Edit J pelete f Product Registration PRIVACY LEGALNOTiCe covTacT US SEST GOEL Link COPYRISHT 1896 2007 SAMSUNG TEC CO LTD Famy srme wick Link W Figure 8 The List of Product Be able to confirm the information of connected equipment if click lt check gt button of Product information 65 Network Camera SNC 570 Product Information ID domain user PRODUCT MODEL NUMBER SNC 570 CLASSIFICATION Urban security LOCATION Namsan Tower REGISTRATION DATE 2008 05 22 MAC ADDRESS x CLOSE Figure 9 Product information Move to Login website of relevant product if click lt view gt button of view The buttons which are lt Edit gt and lt Delete gt of product management move to relevant page through input password to item that fertilize or erase information of registered equipment in List of product Only ID Domain of product should establishes again as ID Domain aft
14. OK 2007 01 07 12 13 41 User Connected IP 192 168 1 34 SNC 570 IP Network Camera Now Started 2007 01 07 10 04 01 User Connection Admin Login OK 2007 01 07 10 04 01 User Connected IP 192 168 1 34 2007 01 07 05 58 36 User Connection Admin Login OK 2007 01 07 05 58 36 User Connected IP 192 168 1 34 2007 01 07 05 57 33 User Connection Admin Login OK Send Log to Administrator E mail per Day at 04 00 Item Description Lines Set up number of lines of the list Log is viewed with number of lines you set up most View recently Clear Delete logs Send Log to Sends logs to the administrator via E mail at the Administrator same time 04 00 every da E mail per Day y day 86 4 2 Using Administration page 4 2 14 Upgrade Upgrade program of SNC 570 network camera gt System Upgrade gear oe eo Firmware Current Version 0 0 1 Last Updated 2008 07 12 18 36 Factory Reset System Upgrade Configuration Item Description SNC 570 Upgrades the firmware of the SNC 570 network Firmware camera Factory Mode Setup If you click lt Reset gt button server is returned to initial value when shipped from the factory after confirmation procedure by administrator If you perform the Factory Mode Reset function the IP will be reset to 192 168 1 100 a value set Caution 2t the time of shipment from the factory In this case you may not log
15. SNC570 English only O Location English only D Description _ English Only O Memo Memo i English Only o 53 Network Camera SNC 570 4 2 2 Live Please Move to Web Viewer page al Live SNC570 Web Viewer live screen 54 4 2 Using Administration page 4 2 3 Basic Setup menu for basic configuration Video Audio S E Video Format ntsc PAL E Compression Type 7 MPEG 4 MJPEG E Initial Resolution D1 O CIF QCIF MPEG 4 MJPEG D1 Very High Very High M er cIF Very High 1 Very High a Rios acr evne w vernon X ot bofs w iots M Video e Frame CIF Bofps 30fps x Rate QCIF 30fps 30fps J Video Channel Channel 1 E Audio In Channel Channel 1 J Audio Out Channel X use D Max UserCounts 10 E Mic Sensitivity High OLow Product r Model si D MacAddress ids ee CameraName 5NC570 _______ English only Location Location English Only Description Description ____ English only EO Memo Memo English Only Ee Video Audio Setup Item Description Video Format If you select the type of camera installed NTSC or PAL you can choose the size of the view on the camera 55 Network Camera SNC 570 Item Description Compression Type Video compression type This defines how the video is compressed Initial Resolution Defines the size of the live screen view Video Quality
16. TECHN CO LO ram sre Hi QuickLink Figure 7 The list of registered equipment 63 Network Camera SNC 570 O Step3 Configure DDNS information in the equipment Click the part of Network Configuration in website of Network Camera Click USE DDNS in order to do Enable and input the address of DDNS Server Default www samsungipolis com Enter the ID and Password that is written when register product is in iPOLiS website Network Network Configuration IP Address 192 168 1 iil NetMask 255 255 255 0 an sGateway 192 fee a 0 DNS1 168 26 63 2 DNS2 168 126 63 2 O xDSL User Name Password O pice Port DDNS Configuration Connection Port 4000 default 4000 SETIP ROR ad default 80 aR TP Port 2a default 21 O use pons DDNS Server www samsungipolis com 10 Password Continuous Jpeg Image Transmission to FTP Server Jpeg CIFs Enable o FrameRate 1 Server Name Home Directory User ID User Password Streaming Engine RTSP TCP Enable o RTP UDP Enable o RTP Multicast Enable C Multicast 1P eza 0 p p Multicast Port 4000 Streaming Image Resolution bY The Configuration of DDNS in SNC 570 is Completed 64 4 2 Using Administration page O Step4 Confirm the connection status of relevant product in product list of iPOLiS website roue seue iPOLIS WHATS POLIS PRODUCT
17. Time gt Time Current Time Date 2008 07 13 Time Setup Time 15 03 19 Set Manually Date yvyy mm dd Time hh mm O TimeServer Serveri pool ntp org GMT 09 00 Y Server2 asia pool ntp org Server3 europe pool ntp org Server4 north america pool ntp org Servers time nist gov o Current Time Item Description Date Current setup date displayed Time Current setup time displayed Time Setup Item Description Set Manually Adjust time manually Time Server Set up address of time server for Server 1 5 85 Network Camera SNC 570 4 2 13 LOG Recent activities made for camera are displayed as log Log View E Lines Bo EE ota current Log 240 Lines _ciear 2007 01 07 14 26 22 Channel closed ip 192 168 1 34 2007 01 07 14 15 55 User Connection Admin Login OK 2007 01 07 14 15 55 User Connected IP 192 168 1 34 2007 01 07 13 28 42 User Connection Admin Login OK 2007 01 07 13 28 42 User Connected IP 192 168 1 34 2007 01 07 12 32 55 Channel closed 192 168 1 34 2007 01 07 12 26 17 Channel close 192 168 1 34 2007 01 07 12 23 45 Channel closed ip 192 168 1 34 2007 01 07 12 20 06 User Connection Admin Login OK 2007 01 07 12 20 06 User Connected IP 192 168 1 34 2007 01 07 12 13 48 User Connection Admin Login OK 2007 01 07 12 13 48 User Connected IP 192 168 1 34 2007 01 07 12 13 41 User Connection Admin Login
18. decide whether transferring related information to FTP E mail In case event occurs by sensor Sensor 1 or Motion Detection MD or Video Analytics on the screen decide whether transferring related information by e mail FTP E mail Setup Set up FTP server and e mail information to which related information is transferred in case alarm occurs Item Description Server Name Enter domain or IP address of FTP server Set up home directory to save relevant FTP Home Directory data at FTP server User ID Enter ID to connect FTP server User Password Enter PW to connect FTP server 83 Network Camera SNC 570 Item Description Recipient E mail You can designate up to two e mail Address 1 bee eee address receiving data when alarm Recipient E mail occurs Address 2 i SMTP Server If you use an external E mail server Name enter the name of the E mail server Use If you use an external E mail server Authentication determine whether to use ID and E mail password ID Enter ID to connect the outside e mail server Password Enter PW to connect the outside e mail server Mail Subject Enter the subject of mail to be transferred Mail Body Enter the body of mail to be transferred je When an event is occurred a copy of JPEG format Note image is transferred to the E mail or FTP server 84 4 2 Using Administration page 4 2 12
19. in depending on the installation environment When you reset a camera function related to video you need to initialize the setting of the OSD menu as well see How to Operate Camera in Chapter 5 87 Network Camera SNC 570 4 2 15 System Reboot iPOLisS Log View Live z D Lines 2o EH crotal current Log 240 Lines 22 Channel closed ip 192 168 1 34 A 55 User Connection Admin Login OK 55 User Connected IP 192 168 1 34 42 User Connection Admin Login OK 42 User Connected IP 192 168 1 34 55 Channel closed ip 192 168 1 34 17 Channel closed ip 192 168 1 34 45 Channel closed ip 192 168 1 34 06 User Connection Admin Login OK 06 User Connected IP 192 168 1 34 48 User Connection Admin Login OK 48 User Connected IP 192 168 1 34 User Connection admin Login OK 41 User Connected IP 192 168 1 34 ISNC 570 IP Network Camera Now Started 2007 01 07 10 0 t2007 03 07 10 2007 01 07 OS 2007 01 07 05 5 Q Are you sure that you want reboot the system 2007 01 07 05 5 Cancel_ Motion Detection C Send Log to Administrator E mail per Day at 04 00 2007 01 07 14 Network Video Analytics Rolsetting User Pan Tilt Zoom ie i Alarm Sensor O dU eaaa Time t Log Upgrade E system Reboot Log Out Server is rebooted after confirmation procedure of administrator
20. necessary information when using alarm function by attaching sensor to camera Alarm Sensor Setup E Digital In Sensor Setup Sensor No Sensor1 Sensor Type Normal Open E Digital Out Alarm Setup Sensori MD Video Analytics Alarm Oo o o Duration FTP E Mail gt FTP E mail Setup O FTP Setup FTP Server Name Home Directory User ID User Password E E Mail Setup 30 sec o o m o Recipient E mail Address 1 Recipient E mail Address 2 SMTP Server Name Cluse Authentication Mail Subject Mail Body 82 Pw SNC 570Message SNC 570Event oO Cancel English Only English Only 4 2 Using Administration page Alarm Sensor Setup Digital In Setup Item Description Sensor No Shows the sensor number Sensor1 Sensor Type Types of sensors are Normal open and Normal close This selects up type of connected sensor Digital Out Setup Item Description Alarm Set up Digital Out responding when event is recognized by connected sensor Sensor 1 Video Analytics or Motion Detection MD Duration Set up time to operate relay It means the period from the time when sensor detects event to the time when relay is released 1 2 3 4 5 30 sec and 1 2 3 min or always FTP In case event occurs by sensor Sensor 1 or Motion Detection MD or Video Analytics on the screen
21. not allowed except for the copy for general use within the scope of copyright law Contents Contents Preface prina tive aia aa K a aha i Contents osondan E Naaa 1 Not to USP viievesiiccccvzevoseaveredcntinenniavenessereheetaticaasrest 4 Product Warranty and Limitations 0 c ceeeeeeeeee 7 Warning SYMDOIS s 22 2 4t ce ceem antl acen e NaN 8 Dangah ninth nai Gane a ae a aeria 8 Caution a eed CA eae a dele 11 Chi OVOPVIOW ccs ciscccsccctecscsnescescenecvsssase can indie tadas apada p indai 13 1 1 SNC 570 Network Camera Introduction 14 12 FO AtUIGS aiae aa a Ate kee oiana das 14 Ch2 Production Description ccsccceseceeeseceeeeeeeeesseeees 19 2 1 Components and Accessories 20 2 2 Section names and functions ee eeeeeteeeeeeeeee 21 oa J VR al 10 eee RR eee nee ees ee ee AOA nee T sore 21 22 2 SIAC PEONO EAN EEES AEE ENS 22 2 2 3 BOHOM eoe ey a reaa AtA 23 22 4 BACK EEE N AAEE aoe AAEE 24 2 3 Recommended PC specifications ceeee 26 Ch3 Installation and Network Setup ssscssecesseeees 27 3 10 Lens Installation issi ai 28 3 2 Connecting to Monitor cceeeceeeeeeeeeeeeteeeeeeees 32 3 3 Connecting to POWER ccceeeceeeeeeeteeteeeeeeeeeseeees 33 Network Camera SNC 570 3 4 Connection to External Control Connector 35 3 5 Network configuration and connection method using Web page 39 Ch4 How to U
22. product the changed IP address can be easily recognized Register the product in the DDNS server in order to register the IP address in the DDNS server Enable the Use DDNS option and enter the submitted ID and password into the server 44 Ch4 How to Use Web Viewer Network Camera SNC 570 4 1 How to Use Web Viewer 4 1 1 Login To connect the login page enter IP address of the camera on a internet Web browser and push enter key O USER D fects a neve ZEE Enter user ID and password and push lt Login gt button then it move to related Web page Default value is ID admin PW 11111111 If you click lt Guest gt button it move to WebViewer page under the Guest authenticated status In this case administrator should permit the Guest connection If you logged in first as a administrator mode please a t change the password of administrator It can prevent ore from other users connection to administration page 46 4 1 How to Use Web Viewer 4 1 2 Web Viewer screen Web Viewer screen is composed of menu area for camera video configuration and screen area for displaying input video from camera 1 11 43 03 m Controls Activated when Video Analytics is enabled Video Analytics Convert to Video Analytics mode This button is activated when the Video Analytics Enable option is selected on the Video Analytics page A menu arrangement of the Analytics mode is diff
23. screen is displayed select White Bal by using the Up and Down buttons so that the arrow indicates White Bal Select a desired mode using the Up and Down buttons MAIN SETUP 1 LENS DC J 2 EXPOSURE J gt 3 WHITE BAL ATW 4 BACKLIGHT OFF 5 SSNR ON J 6 DAY NIGHT AUTO J 7 IMAGE ADJ J 8 SPECIAL 9 EXIT Select one of the following 5 modes as appropriate for your purpose ATW Select this when the color temperature is between 1800 K and 10500 K INDOOR Select this when the color temperature is between 4500 K and 8500 K OUTDOOR Select this when the color temperature is between 1800 K and 10500 K sodium light inclusion AWC gt SET To find the optimal setting for the current luminance environment in this mode set the point the camera towards a sheet of white paper and press the SET button If the environment changes readjust it MANUAL Select this to fine tune White Balance manually Set White Balance first by using the ATW or AWC mode After that switch to MANUAL mode fine tune the White Balance and then press the SET button 97 Network Camera SNC 570 A caution White Balance may not work properly under the following conditions In this case select the AWC mode When the color temperature of environment surrounding the subject is out of the control range e g clear sky or sunset When the ambient illumination of the subject is dim f the camera is directed t
24. sees video Z Controls Z Audio In a user2 mias M video M Controls X Audio In o user3 pitas V video X Controls V Audio In user4 osese 4 Video Controls Audio In o users pose Video Controls X Audio In O Controls Pan Tilt Camera Audio Out Alarm Out Item Description Administrator Password Change Change password of administrator Guest Setup User clicks Guest button to decide whether allowing guest to connect Main Viewer Current User You can register new user or delete and set up user s authority The default password is user1 user5 76 4 2 Using Administration page X Set up user authority User s authorities set up at Current User are as follows Catetory Description Video Use video related setup function r Compression Resolution Video Analytics Control Pan Tilt Zoom Audio output Alarm output Audio Audio Input USE Whether relevant account is used If not checked not allowed log in Example 1 In case control function is limited Do not check Controls box SNC570 OOO 1 43 03 Xx Pan tilt zoom audio output alarm output function icon is inactivated At Network Camera SNC 570 Example 2 In case video function is limited Do not check Video SNC570 X Compression Resolution set up icon is inactivated 78 4 2 Using Administration page 4 2 9 Pan Tilt Zoom Configures PTZ Swi
25. supports data and power simultaneously with only connection of LAN cable without separate power input cable installation for power excitation to the product When connecting camera to PoE device please connect to the device complying with PoE IEEE802 3af specifications In case non standard product is used it may cause performance degradation or trouble 34 3 4 Connection to External Control Connector 3 4 Connection to External Control Connector The input order of terminal from left is Alarm input Alarm output Ground RS 485 signal RS 485 signal When connecting cable push stripped part of electric wire in while pushing quadrangle button and take hands off from the button then the wire will be fixed ALARM RS 485 rare eta Alarm Input Ve Vee s lt ICCCEIE Alarm Output i Ground RS 485 Signal BOG R8 485 Signal 35 Network Camera SNC 570 m Connecting Alarm Input This is the input terminal for external alarm signal use it by connecting as following 0c 3 3v Q Camera Inside 47K Q CMOS WW gt Alarm In Sensor Input if 2209 SH 0 NENES 0 a q e Incase of selecting Normal Open at setup menu In case of contact type it is short and in case of active type sensor input acts at LOW level Incase of selecting Normal Close at setup menu In case of contact type it is open and in case of a
26. value the picture outline becomes stronger and clearer Adjust this value appropriately depending on the sharpness of the picture 5 2 How to Set Up Functions RETURN Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP menu When H REV or V REV is selected any text in A E the picture also will be flipped horizontally or Caution vertically If you increase the SHARPNESS level too high the picture may become distorted or noise may appear 5 2 8 SPECIAL 1 When the SETUP menu screen is displayed select SPECIAL by using the Up and Down buttons so that the arrow indicates SPECIAL 107 Network Camera SNC 570 gt 8 SPECIAL J 2 Select a desired mode using the Up and Down buttons gt 1 CAM TITLE CAM TITLE If you enter a title the title will appear on the monitor 1 If the SPECIAL menu screen is displayed use the Up and Down buttons so that the arrow indicates CAMTITLE 2 Set it to ON by using the Left and Right buttons 108 5 2 How to Set Up Functions be displayed on the monitor screen even if you When the CAM TITLE menu is OFF no title will Caution enter one gt 1 CAM TITLE 3 Press the lt SET gt button 4 Use the 4 direction buttons to move to a desired letter and select the letter by pressing the SET button Repeat this to enter multiple letters You can enter up to 15 let
27. 2 Membership Registration SIGNUP SIGNUP My IPOLIS gt Signup Welcome to IPOLIS SS We provide real time online video service for IPOLIS products through this web browser We recommend strongly every purchaser of IPOLIS products sign up for POLIS online Manage your account 1D Create password of 6 to 12 characters in length an containing letters A Z or numbers 0 9 PASSWORD Check NAME JOB Choose x E mail ADDRESS TEL MOBILE PHONE E N n Manage company account COMPANY TEL FAX ADDRESS SIS GES Figure 3 Membership Registration Input your information 61 Network Camera SNC 570 O Step2 Register the equipment after login WELCOME to IPOLIS ID andy PASSWORD 0000000 y es i MEMBER JOIN ID PW SEARCH Login Signup for POUS online User ID and password don t match Figure 4 Login Product List My IPOLIS gt Product List Current product list is displayed gt If wanted product is not in the list click Product Registration at the bottom WO iD Model Location Status View Infomation Management 1 andy3300 SNP 3300 AMBASSADOR HOTEL OFF arm Edit Delete 2 andy550 SNC 570 Lab OFF arm a oo Product Registration Figure 5 The list of registered equipment 62 4 2 Using Administration page Product Registration My IPOLIS gt Product Registration Mandatory Information hip wnw anounelpals con
28. ACY Hide an area you want to hide on the screen 1 When the SPECIAL menu screen is displayed press the Up and Down buttons so that the arrow indicates PRIVACY 2 Set up the mode using the 4 direction buttons AREA SEL You can select up to 8 MD areas AREA MODE Determines whether to use the area selected in the AREA SEL and the size and position of the area 112 5 2 How to Set Up Functions AREA SEL You can select up to 8 MD areas AREA MODE Determines whether to use the area selected in the AREA SEL and the size and position of the area Press SET to Return MASK COLOR Determine area color You can select Gray Green Red Blue Black White TRANSP Determine the transparency of selected area as controlling number from 0 to 3 RETURN Select this to save the PRIVACY menu settings and return to the SPECIAL menu DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind The chance of resolution decrease is existed A because DIS function uses the digital zoom Caution DIS doesnt operate when background illumination is too low DIS doesn t operate when object pattern is monotonic as like sky or white wall When using the DIS mode the D ZOOM level is required to set up over 46 LANGUAGE You can select the menu language according to your requirements RESET Resets the ca
29. Address 192 168 1 100 NetMask 255 255 25s 0 an Gateway 192 168 1 is DNS1 168 126 63 i DNS2 68 126 63_ 2 O xDSL User Name RE DHCP Item Description When network product is connected to normal LAN Use local LAN or when connected to static IP the network data to be allotted to the IP is configured When using xDSL dynamic IP enter the ID and xDSL PW When automatically receiving IP through DHCP server the DHCP functions are activated DHCP DHCP is used in the LAN environment where the DHCP is activated Generally for mid large scale DHCP servers are operated through LAN and for small scales IP sharers use DHCP functions 43 Network Camera SNC 570 Port Configuration Port DDNS Configuration Connection Port HTTP Port 4000 default 4000 80 default 80 FTP Port 21 default 21 Use DONS DDNS Server www samsungipolis com ID Password Item Description The connection port and http ftp port Port Setting configurations can be set here and the DDNS use can be checked Use DDNS changes its IP address every time the user attempts to connect to the ISP and when the product Pad is connected to a cable modem or xDSL modem In this case the user cannot know the changed IP address When a product that uses dynamic IP is registered on the DDNS server when wishing to connect to the
30. Caution i When the power is DC 12V the SYNC menu is fixed to the INT mode MOTION DET If you connect an alarm device to this camera you can monitor MOTION DET activity more efficiently because SENSITIVITY AREAL e AREA MODE ON a signal is generated by the camera whenever motion is detected The motion detection signal is output through the MD OUT port 1 When the SPECIAL menu screen is displayed press the Up and Down buttons so that the arrow indicates MOTION DET 2 Set up the mode using the 4 direction buttons SENSITIVITY You can select up to 8 MD areas When SENSITIVITY number is high motion detection sensitivity is increased to recognize even small movement AREA MODE Determines whether to use the MD area selected in SENSITIVITY SEL POS Determines which of the 4 vertices of each MD area is to be used 111 Network Camera SNC 570 YPOS Determines the coordinate of the vertical axis for SEL POS XPOS Determines the coordinate of the horizontal axis for SEL POS FILL gt SET Fills in a selected MD area Fills in a selected MD area The color of filling is sequentially selected as brown orange blue cyan yellowish green yellow and red RETURN Select this to save the MOTION DET menu settings and return to the SPECIAL menu MD areas show only MOTION DET menu A a Therefore MD areas don t display on the monitor Caution screen PRIV
31. PSAMSUN Ge iPOLis Anywhere in Real time Network Camera SNC 570 User s Manual Thank you for purchasing a SAMSUNG polis Network CAMERA Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use ENGLISH Preface reOLkis A brand that is integrated into Samsung s network products IPOLIS stands for a convenient world Polis made safe Police through Samsung s superior network performance Internet protocol With IPOLIS products clear digital images transmitted over the internet real time monitoring is possible anywhere with an internet connection Easy remote control functions and the use of existing networks minimize installation costs With IPOLIS experience a world of convenience connected anytime anywhere Preface Thanks for purchasing of SNC 570 camera This is a user instruction manual for high resolution WDR network camera and the product mentioned here designates the high resolution WDR network camera The user who installs and operates the product shall be aware of this manual and other manuals referenced by this manual before the installation and operation and use properly This manual and the software and hardware explained here are protected by copyright law So the copy reprint and translation to other languages of a part of or all contents of this user manual without permission of SamsungTechwin Co LTD are
32. SNC 570 5 2 6 DAY NIGHT You can display pictures in color or black and white 1 When the SETUP menu screen is displayed select DAY NIGHT by using the Up and Down buttons so that the arrow indicates DAY NIGHT MAIN SETUP 1 LENS DC J 2 EXPOSURE H 3 WHITE BAL ATW 4 BACKLIGHT OFF 5 SSNR ON JJ p 6 DAY NIGHT AUTO J 7 IMAGE ADJ J 8 SPECIAL J 9 EXIT Select a desired mode using the Left and Right buttons according to the picture display you want COLOR The picture is always displayed in color 104 B W The picture is always displayed in black and white Please press SETUP button to turn on or off the burst signal on B W mode AUTO The mode is switched to Color in a normal environment but switches to B W mode when ambient illumination is low To set up the sswitching time or speed for AUTO mode press the SET button BURST SETUP gt MODE ON Press SET to Return AUTO SETUP gt DWELL TIME 10 SEC DURATION FAST Press SET to Return 5 2 How to Set Up Functions DWELL TIME You can select the duration time about changing the day night mode 5s 7s 10s 20s 30s 40s 60s DURATION You can select brightness of illumination about changing the day night mode Color gt B W B W gt Color Fast 2 5 lux 4lux Slow 0 8lux 6lux X The brightness of illumination is changeable by installed environment You can easily switch between ni
33. T LEVEL MIDDLE 50 Press SET to Return HLC High Light Compensation If there is a high light installed in a limited environment such as an apartment parking garage or gas station entrance removing the high light makes it possible to view car license 100 plates efficiently DAY In normal daylight conditions the HLC is not activated NIGHT If a high light that is larger than a certain size is present on the screen remove the high light to see license plates clearly 5 2 How to Set Up Functions HLC MASKING AREA lt HLC ON gt lt HLC OFF gt HLC Enable a user to select a mask color of high light area from a picture Press SET to Return OFF Not being used 3 Select a desired mode using the Left and Right buttons and press the SET button A caution You cannot use the WDR mode when MANUAL or A FLK mode in SHUTTER menu is selected Since the following symptoms may occur according to the ambient illumination when WDR is selected set it to OFF Color or screen changes unnaturally Noise appears in the bright part of the screen Since the performance of the WDR function may be affected by the area of the bright part of the screen optimize the installation angle 101 Network Camera SNC 570 for the best WDR performance If you increase LIMIT the screen display may be distorted For high performance of WDR function using
34. alance capacity of SD memory Warning Message In the event of memory overflow or memory Off error it is not display the warning message In the event of memory overflow it erases Overwrite record files chronically and records new events 74 4 2 Using Administration page Item Description Analytics Detection When Analytics is detected you can save it Recording Motion Detection When a motion is detected you can save it Recording MD Sensor Detection When the Sensor detects a motion you can Recording save it Plays the video Stops the video Pauses the video Save the video image as a JPEG file Event Record List Event record list stored in the SD memory X This system records images 5 seconds before and after the event X You can record Event up to one minute A ution We provide SD Memory card only not the MMC Only 128MB 2GB SD cards can be used while 4GB SDHC is supported We recommend the FAT32 format Make sure that you turn off the camera before you insert or take out the SD memory card 75 Network Camera SNC 570 4 2 8 User This describes password change for administrator or user registration User Administrator Password Change Type Re Type Guest Setup Guest Access C Permission Current Users User Name Password Control Level Use usert
35. ctive type sensor input acts at high impedance status open collector 36 3 4 Connection to External Control Connector m Connecting Alarm output This is the output terminal for external alarm signal use it by connecting as following Open Col lector Relay Relay 2 2K Q M Output CMOS Output 10K Q Relay Power ik F Alarm output part is Open Collector structure and can be composed by using relay Rated maximum value is DC 24V 100 mA 37 Network Camera SNC 570 m Connecting RS 485 X Connect the RS 485 to SRX 100B with the plus signal to plus and minus signal to minus X The terminating resistance of the RS 485 can be set in the RS 485 termination of the Basic menu X GND pin of RS485 part may be not to be connected X It may be effective when communication is not working properly m Connecting Audio X Connect the Phone Jack Audio Input terminal Mic Mono to the AUDIO IN terminal X Connect the Phone Jack Audio Output terminal speaker to the AUDIO OUT terminal 38 3 5 Network configuration and connection method using Web page 3 5 Network configuration and connection method using Web page Use when there is one SNC 570 network camera to be installed 1 Please connect user s PC to SNC 570 network camera using cross cable am Le ts tial y a CLASS 2 ONLY 39 Network Camera SNC 570 To c
36. emorize an event at the SD Memory when it activated Privacy function Privacy function is to determine surveillance area not to display on the monitor for privacy protection RTSP RTP UDP RTP Multicast support Electronic IRIS Electronic IRIS shuttering enables continuous automatic shutter control in the range of 1 60 to1 120 000 seconds VIDEO DC Lens driver Simple switch operation is enough to choose video driving lens or DC driving lens High Sensitivity High sensitivity color CCD delivers vivid images in the low illumination of 0 001 Lux Sens up 256X 1 2 Features Combination of motion detection and alarm Combination of motion detection video analytics and alarm enables still image storage in the SD Memory or transmission of still image via email or FTP High data compression ratio High compression in MPEG 4 provides fast transmission and relatively high volume transmission of frame in the same network band Real time interactive audio Transmission Additional functions SENS UP Mirror SHARPNESS SYNC choice INT LL Network Camera SNC 570 18 Ch2 Production Description Network Camera SNC 570 2 1 Components and Accessories O High Resolution Day amp Night Network Camera et nner enn aul Program O User s Manual CD Quick Guide O C Mount adaptor O Auto iris lens connection plug O Cross Cable O DC 12V Adapter Power Cord 20 2
37. er deleting because it can t be fertilized WELCOME to IPOLIS Dian PASSWORD 9000000 K MEMBER JOIN IDPW SEARCH Login Sign up for POUS online User D and password don t match yw sere Figure 10 Edit Delete 66 4 2 Using Administration page How to use Streaming Engine We recommend VLC media player among Streaming Engine products O Step1 Network Page configuration Click the certain function of Streaming Engine and press lt Save gt button To update Network Page configuration the system will reboot O Step2 VLC media player execution When you execute VLC media player below screen capture will appear 4 YLC media player View Settings Audio Video Navigation Help PB ua E 100 O Step3 VLC media player connection and configuration RTP UDP connection Select FILE in the menu and click Open Network Stream Enter rtsp serverip mpeg4unicast in the RTSP URL and press lt OK gt button to connect to RTP UDP 67 Network Camera SNC 570 File Disc DirectShow OuppyrTp OUDP RTP Multicast OHTTP HTTPS FTP MMS rTsP URL rtsp 192 168 1 100 mpegdunicas Advanced options Stream Save ettir Caching Customize rtsp 192 168 1 100 mpeg4unicast RTP TCP connection Select Settings in the menu and click Preferences then check the Advanced options box at the bottom of
38. erent with one of the Control mode 47 Network Camera SNC 570 a RESET Displayed when the Video Analytics mode is on This sets the current screen image to the background 7 Alpha branding Displayed when the Video Analytics mode is on Makes changed parts appear half transparent It is not recommended to use alpha branding in Caution the low specification system 48 4 1 How to Use Web Viewer Flip Image Turns the screen upside down Stretch Image Expands the screen to the size of D1 when selecting CIF and QCIF for resolution Save Image Saves the channel screen as a JPEG file Compression Video compression mode the mode of compressing video MPEG JPEG Resolution Video resolution the size of video screen transmitted NTSC D1 704x480 Half D1 704x240 CIF 352x240 PAL D1 704x576 Half D1 704x288 CIF 352x288 49 Network Camera SNC 570 Frame Rate Setting on the Basic page The number of maximum video frame transmitted for each second 1 5 10 15 20 25 30 Quality Setting on the Basic page Video quality Very High High Normal Low Very Low T Pause Stops video for a while Q OSD Displays related information Displays the title Removes the title 50 4 1 How to Use Web Viewer Q Camera Setup Displays OSD control button of camera _ WHITE BAL 4 BACKLIGHT SSNR DAY NIGHT IMAGE ADI Came
39. etermine use of DDNS server Use DDNS DDNS allows you to connect to the server transforming dynamic IP Continuous Jpeg Image Transmission Item Description Determine use of Continuous JPEG Image Enable eh gt Transmission function FrameRate Determine frame rate frame per seconds to send out Server Name Enter domain name or IP address of the FTP server Home Directory Configure home directory to store assigned data of the FTP server User ID Enter ID to access to the FTP server User Password Enter Password to access to the FTP server 58 4 2 Using Administration page Streaming Engine Item Description RTSP TCP Enable Determines whether to use RTSP TCP RTP UDP Enable Determines whether to use RTP UDP RTP Multicast Enable Determines whether to use RTP Multicast The default setting of Multicast IP is Streaming Image 224 0 1 1 Determines the resolution of the Streaming Resolution Engine Unicast RTP streaming RTP over UDP is the adequate image transmission method to send out the latest image despite of video loss RTP over RTSP RTP tunneled over RTSP is useful to install a relatively simple firewall which accepts RTSP data streaming Q Unicasting is adequate to VOD Video On Demand 2 broadcasting since it sends out video data only with Note data transmission demand Multicast RTP RTP over UDP sends o
40. f their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes Product Warranty and Limitations Product Warranty and Limitations The manufacturers of this product do not take any responsibility for this product therefore the manufacturer does not authorize the third party but allows that retailer is responsible The product warranty does not extend to cover accidents negligence abuse or wrongful use for the whole or any part of the product Additionally the manufacturer does not provide warranty for any additional parts or affiliations The warranty is for one year from the purchase date During the per
41. f this product is not connected to any recording equipment as this can cause problems 3 3 Connecting to Power m AC DC Power Both of AC24V and DC12V can be used for the input power of this product When using other adaptor not the adaptor DC12V 4A provided by the company make sure that the specification is over AC 24V 1A or DC12V 2A m AC DC Combined use In case of SNC 570 as recommended adaptor specification is over AC 24V 1A or DC12V 2A please use surely the adaptor complying with this specifications 33 Network Camera SNC 570 Table 3 1 When the resistance val ue of copper wire is at 20 C 68 F Copper wire size 24 22 20 18 AWG 0 22mmr 0 33mm 0 52m 0 83m Resistance value 2m 0 078 0 050 0 030 0 018 Voltage drop V m 0 028 0 018 0 011 0 06 e As shown in the Table3 1 voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera X Standard voltage for camera operation DC 12V 10 AC 24V420 X There may be some deviation in voltage drop depending on the type of wire and the manufacturer A ution In case PoE and power adaptor are connected to camera simultaneously the power authorized first by the product is used m PoE Power Over Ethernet POE Power Over Ethernet is the function of LAN related devices which
42. ght and day modes by adjusting the D amp N button on the webpage AUTO gt BW COLOR e BW A ution When using a Video Auto Iris Lens if you set the lens level to low automatic switching between Color and Black amp White may not occur You cannot control the DAY NIGHT menu when AGC in the EXPOSURE menu is OFF At this time the exchange between DAY mode and NIGHT mode operates as like selecting COLOR mode The camera may focus less well under infrared illumination than under normal illumination Since the camera may not focus as well under infrared illumination at night as it does under normal illumination install an Extra low Dispersion Lens to obtain sharp pictures 105 Network Camera SNC 570 5 2 1 106 7 IMAGE ADJ When the SETUP menu screen is displayed select IMAGE ADJ by using the Up and Down buttons so that the arrow indicates IMAGE ADJ MAIN SETUP 1 LENS peal 2 EXPOSURE J 3 WHITE BAL ATW 4 BACKLIGHT OFF 5 SSNR ON J 6 DAY NIGHT AUTO J gt 7 IMAGE ADJ J 8 SPECIAL J 9 EXIT Select a desired mode using the Up and Down buttons IMAGE SETUP gt 1 FREEZE OFF 2 V REV OFF 3 H REV OFF 4 D ZOOM OFF 5 SHARPNESS ON J 6 RETURN J FREEZE You can view still or moving pictures V REV You can flip the image vertically H REV You can flip the image horizontally D ZOOM You can digitally zoom by a factor of X1 to X10 SHARPNESS As you increase this
43. heck the created network place first before trying to connect to a network e Please use only the power adapter that is provided with the product e Please check national laws to be sure that using the product for monitoring purposes is not illegal Ch1 Overview Network Camera SNC 570 1 1 SNC 570 Network Camera Introduction The SNC 570 is a high tech network camera that uses MPEG 4 codec technology to allow high compression rates and clear picture quality by allowing for high frame rates to be transmitted through the network By using the network remote connection monitoring and control is possible from any location for simple use additionally set up requires only a network The SNC 570 Network Camera utilizes embedded software solutions Embedded Web Server Embedded Streaming Server Network Protocol developed by SamsungTechwin and guarantees performance and safety while offering various solutions through Internet integration 1 2 Features O High Resolution The horizontal resolution of 560TV lines at color mode and 700TV lines at BW mode can be achieved by using a high density SONY CCD having double speed 410 000 pixels which provides clean noiseless and reliable pictures O Multi channel Real time image encoding Single Chip MPEG4 and JPEG codec enables real time image encoding and transmission through multi channel of classified resolution of D1 CIF QCIF 1 2 Features O Wide Dyna
44. ing Please check the audio is selected from admin page Please check speaker volume from the viewer In case input sound through microphone at Viewer is not outputted through Audio Out of server please check whether Audio Out channel is selected at admin page Or check whether microphone is available at Viewer Please check audio driver is working in user s PC Video is stopped Please check whether network cable of SNC 570 network camera is correctly connected In case user uses hub or IP router check whether these network equipments are working properly Open MS DOS window and check whether SNC 570 network camera is connected to network 118 Troubleshooting Problem Solution No image from web viewer Click refresh shortcut F5 button at browser to recall the page Check whether power of camera and network cable is properly connected Check whether computer is connected to network If you use hub or router check whether such equipments are properly operated Note Open MS DOS window and enter network ID of camera at ping 192 168 1 100 Connect to Admin page to check whether video output is selected Image transferred to FTP or by E mail cannot be viewed Video may not be viewed since Divx codec is not installed in user s PC Divx codec can decode video compressed with MPEG4 Download and install the latest Divx codec and check video http www divx com divx d
45. iod warranty does not extend to malfunction in these areas e Malfunction due to user s negligence Dismantlement or replacement by the user e Connection to alternate power source e Malfunction due to natural disasters fire flood tsunami etc Replacement due to wear and tear e Instability of network Network Camera SNC 570 Warning Symbols Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use Danger Misuse or wrongful operation of the product may result in death injury or bring about other fatal results It indicates absolute caution when operating Caution Misuse or wrongful operation of the product may result in slight injury or damage to the product It indicates caution when operating Note Indication that the user needs to be aware of certain matters or will find matters helpful in operating the product Danger Before Setup e Please set up the proper voltage before connecting to power source e Please be sure the power is turned off before setup Danger There is risk of shock or fire be sure to avoid setup in places with high humidity To prevent shocks please connect the ground wire Do not install the camera on a surface that can not support it Unless the surface is suitable it could cause falling or other hazards During Use When opening the product cover there
46. is a risk of electric shock Only a professional should open the cover Please use only in an environment with standard temperature and humidity Please do not plug in multiple products to a power source it is often the cause of fires Please do not place water or heavy objects on the product it is often a cause of malfunction Please do not use in a location with propane gas gasoline or other flammable substances to avoid risk of explosion or fire Please do not touch the power plug with wet hands to avoid electric shock Do not pull on the power plug with too much force a damaged plug may cause electric shock or fires Don t connect the RJ 45 cable to a terminal by constraint Stop using your camera when you find a malfunction If you use your camera around smoke or unusual heat for a Network Camera SNC 570 long time Fire may be caused Random replacement of built in battery by other types of batteries may cause explosion The battery shall be replaced by the same battery The used batteries shall be disposed carefully because they can cause environment pollutions The battery shall be replaced by the same battery e The used batteries shall be disposed carefully because they can cause environment pollutions The lithium battery incorporated in this product is not user replaceable Replacement of the lithium battery will be done by a trained technician For information on i
47. justable Sens up Auto Off Selectable limit X256 Gain Control High Low O White Balance ATW AWC Manual Indoor Outdoor Electronic shutter speed Auto NTSC 1 60 1 120 000sec PAL 1 50 1 120 000sec Manual A FLK IRIS DC Video 120 Specifications Performance 704x480 D1 704x576 D1 Resolution 352x240 CIF 352x288 CIF 176x120 QCIF 176x144 QCIF Compression MPEG 4 JPEG Dual CODEC with transcoder Up to 30fps Encoding Encode Rate 704x480 Up to 25fps 704x576 Transmission speed Up to 100Mbps Reniote uSETS 90 simultaneously Maximum P i RTP UDP RTP Multicast RTSP TCP IP DHCP raono DNS DDNS HTTP SMTP FTP PPPoE and support NTP Network Video Analytics Missing object detection Appear Disappear Password Security Protection Poveen reve Interface Monitor Output 1 BNC 560 TVL For installation Input 1 Phone Jack Line in 1Vpp MIC in 2K ohm Output 1 Phone Jack Line out 1Vpp Compression ADPCM Audio Sampling rate 8 KHz Inputs Terminal 1 input NO NC Outputs Terminal 1 output NO NC Remote Via E mail or oneshot FTP Alarm notification continuous FTP transmission Ethernet RJ 45 10 100 Base T PTZ control Connections interface Raas smse Stored event image Back up eno 128MB 256MB 512MB 1GB 2GB SD memory card Storage 4GB SDHC memory card 121 Network Ca
48. mera SNC 570 S W Install program Provided IP installer Provided Dedicated viewer Provided SNM64 ActiveX controller for Web Provided server General Input Voltage Dual 12V DC 24V AC PoE IEEE 802 3af Power Consumption Max 8 5W Operating Temperature Humidity 10 C 50 C 30 80 RH Dimension W xH x D 74x61x152mm 2 91 x2 4 x5 98 Weight 580g 1 28 Ib Lens Mount C CS 122 Dimension Dimension 123 SAMSUNG TECHWIN P SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon dong Jungwon gu Seongnam si Gyeonggi do 462 120 Korea Tel 82 31 740 8151 8 Fax 82 31 740 8145 SAMSUNG TECHWIN AMERICA LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Tel 1 310 632 1234 Fax 1 310 632 2195 www samsungtechwin com www samsungcctv com www samsungipolis com SAMSUNG OPTO ELECTRONICS UK LTD Samsung House 1000 Hillswood Drive Hillswood Business Park Chertsey Surrey KT16 OPS Tel 44 1932 45 5308 Fax 44 1932 45 5325 P NO Z6806 0913 01B
49. mera settings to the factory defaults RETURN Select this to save the SPECIAL menu settings and return to the SPECIAL menu 113 Network Camera SNC 570 5 2 9 EXIT Press the SET button in the EXIT menu to save the current settings and exit the SET menu Ch6 Troubleshooting Network Camera SNC 570 If there are problems in operation please refer to the items below If the problem persists please contact the agent you purchased this product from Problem Solution Nothing appears on the screen Please check the power connection Please check the video signal line connection Please check and make sure that the auto lens switch is set to DC VIDEO when using a DC VIDEO lens Open MS DOS window to check whether SNC 570 network camera is connected to network X In case of ping 192 168 1 100 replace it with IP address set up at server The video image is not clear Please check if the lens is clean Please clean the lens with a clean cloth or brush Please adjust the contrast feature of the monitor Please make sure that the screen is not exposed directly to a bright light Please move the camera if necessary Please readjust the back focus of the camera The screen is dark Please adjust the contrast feature of the monitor If you have an intermediate device set the 75Q Hi z properly and check the terminals Please check if an auto iris lens is being used and adj
50. mic Range WDR The main function of the Wide Dynamic Range WDR is to accumulate the scope of contrast between the brightest and darkest points in the picture WDR employing SV IV chipset provides prominent back light compensation effect in high contrast environment O High sensitivity against low illumination Diagonal 6 mm 1 3 CCD of enhanced sensitivity and DSP chipset catch contour and color of objectives only with starlight illumination in the dark which provides reliable outdoor surveillance performance 0 001Lux Lux for color mode 0 00004Lux Lux for black and white mode O SSNR Samsung Super Noise Reduction Samsung s high performance DSP chipset SV IV reduces GAIN variance effectively to deliver clean and clear cut images O DAY amp NIGHT fuction Day amp night function and Sens up function by ICR IR Cut Filter Removal operation produce high quality images for 24 hours X Sens Up function delays exposing time to improve CCD sensitivity X Day amp Night function allows users choose color mode or BW mode depending upon illumination Network Camera SNC 570 O PoE Power Over Ethernet PoE function is to supply power through the LAN cable together with data transmission without power cable for user convenience DIS Digital Image Stabilizer DIS Digital Image Stabilizer function compensates camera shaking to obtain clear cut images SD Memory function SD Memory function is to m
51. n the case of wrongful purchases please exchange the product for a home use product Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection Ms ystems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal Note to User Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment and is taking a number of steps to N I provide customers with more environment friendly products The Eco mark represents Samsung eco Techwin s will to create environment friendly products and indicates that the product satisfies RoHS compliant the EU RoHS Directive
52. ng and Preset of the camera Pan Tilt Zoom Setup E PTZ Camera Configuration Channel chi E PTZ Setup Device ID 1 Model sx E EE Item Description PTZ Display Display PTZ menu OSD Display Display OSD Device ID Select an identification number of the camera Model Select the model installed When PTZ is enabled the Video Analytics feature Caution may not function properly 79 Network Camera SNC 570 4 2 10 Motion Detection This sets up motion detection function of camera Motion Detection Setup Motion Detection Configuration Grid Display M poemas EZI MD Enable MD Sensitivity 3 ilow S High Set Item Description Grid Displa Basic grid used to choose area on the screen is Play displayed or hidden When selecting motion detection area click lt Select Select Area All gt button to select all areas or click lt Deselect gt button to cancel the selected area MD Enable Decide whether you use motion detection function 80 4 2 Using Administration page Item Description Setting up sensitivity to detect motion to adjust input MD Sensitivity video by situation You can select 1 5 and 5 is the highest When the motion detection feature is enabled A 7 the Video Analytics feature is automatically Caution disabled 81 Network Camera SNC 570 4 2 11 Alarm Sensor This sets up
53. on A ution Please use the specified lens connection parts as shown in the picture below The use of the wrong sized parts of the wrong size may cause damage to the inside of the camera or result in poor fitting Use of a lens which is too heavy affects the balance of the camera and may cause a malfunction Please use a lens that weighs less than 450g Please select Av mode if possible when adjusting the automatic light control ALC of an auto lens Use of PK mode may cause hunting C mount lens 10 mm or less l CS mount lens 5 mm or less 31 Network Camera SNC 570 3 2 Connecting to Monitor Please connect the video output terminal located on the back of the camera to the monitor SNC 570 Network Camera Monitor The connection method varies depending on the type of monitor and accessories Please refer to the user s manual for each instrument e Please turn off the power when connecting e Please select Hi Z on the 75Q Hi Z switch for the intermediate video TV set and select 75Qfor the Intermediate device as shown in the picture below SNC 570 Network Camera Intermediate End monitor 32 3 3 Connecting to Power This product is the network camera which A 3 transmits video through network video output Caution terminal is for installation and used to determine imaging range when installing the product Please make sure that the video output terminal o
54. onfigure network the registered in the user s PC Q u ote Local Area Connection Properties General Authentication Advanced B9 Intel R PRO 1000 PL Network Conn Configure A l File and Printer Sharing for Microsoft Networks T JE Q05 Packet Scheduier E2 F Intemet Protocol TCP P Allows your computer to access resources on a Microsoft network Uninstall C msa Properties Description C Show icon in notification area when connected Z Notiy me when this connection has lite or no connectivity After pressing internet internal IP must be protocol TCP IP properties press the advanced button to go into advanced configurations Advanced TCP IP Settings IPaddoseee Paes SEE 123123123123 1921681123 255 255 2550 255 255 255 0 Defaut gateways Gateway Tae maai Automatic utematic metic aaa Add with 192 168 1 XXX 40 3 5 Network configuration and connection method using Web page 192 168 1 100 is the IP address for the camera Caution and will be unavailable as an internal IP address 2 Please launch a Web browser on user s PC and enter 192 168 1 100 in the URL address field and push lt Enter gt button Connect to Webviewer login window of SNC 570 network camera about blank Microsoft Internet Explorer Fie edt view Favortes Tod
55. owards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable 98 5 2 How to Set Up Functions 5 2 4 BACKLIGHT This camera is designed so that it delivers a distinctive subject and background at the same time even when the subject is in backlight unlike conventional cameras by adopting a proprietary SV IV DSP chip 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Up and Down buttons so that the arrow indicates BACKLIGHT MAIN SETUP 1 LENS DC J 2 EXPOSURE 3 WHITE BAL ATW gt 4 BACKLIGHT OFF 5 SSNR ON J 6 DAY NIGHT AUTO J 7 IMAGE ADJ J 8 SPECIAL J 9 EXIT 2 Select a desired mode using the Left and Right buttons depending on the camera purpose BLC Enables a user to directly select a desired area from a picture and to view the area more clearly gt TOP BOTT LEFT RIGHT e LEVEL MIDDLE Select BLC to adjust the area to be enhanced and enhancement level Press SET to Return WDR When there are both bright and dark areas at the same time this mode makes both areas distinctive 99 Network Camera SNC 570 WDR OFF Select WDR to adjust the WDR LIMIT and LEVEL LIMIT Adjust the WDR Sensitivity by selecting LOW MIDDLE or HIGH LEVEL Adjust the WDR Brightness by controlling the bar from 0 to 100 WDR LIMIT gt LIMI
56. ownload Saved contents is not displayed in the SD memory Make sure that you do not take out the memory card while contents are being saved Check if the SD memory card is properly inserted Check if the capacity on the card is correct on the Record Page Product information is not displayed on the local network Check if the network cables are properly connected Check the status after pressing the RESET switch on the back of the product for five seconds to initialize it 119 Network Camera SNC 570 Specifications Model Name SNC 570N SNC 570P VIDEO Imaging Device 1 3 Vertical double density interline CCD Total Pixels 811 H x 508 V 795 H x 596 V Effective Pixels 768 H x 494 V 752 H x 582 V Scanning System 2 1 Interlace Frequency H 15 734 KHz H 15 625 KHz V 59 94 Hz V 50 00 Hz Horizontal Resolution Color 560 TV Lines Min B W 700 TV Lines Min Min Illumination Color 0 3 Lux 50 IRE F1 2 0 001 Lux Sens up 256X B W 0 01Lux 50 IRE F1 2 0 00004Lux Sens up S N Y signal 52 dB OSD Built In Multi language support Camera Title On Off Day amp Night Auto ICR Color BW Backlight Compensation WDR BLC HLC Off Dynamic Range 52dB Motion Detection On Off Output via communication DIS On Off Privacy Masking On Off 8 Programmable zones SSNR On Off Level ad
57. ra OSD is displayed a Day amp Night configuration function Day amp Night Color B W configuration PTZ Control PTZ control function 51 Network Camera SNC 570 Instruction for Camera OSD control button lt t gt lt gt button Moves selection displaying arrows up and down on camera OSD menu lt gt lt gt button Changes configuration of selected field on camera OSD menu lt Set gt button Displays camera OSD or moves to upper lower menu of selected field lt Exit gt button Terminates camera OSD For configuring the function and detail operating method of SNC 570 network camera refer ch5 How to Operate Camera 52 4 2 Using Administration page 4 2 Using Administration page 4 2 1 Initialization Screen after Connecting Basic Screen When connection is successful the below screen will be displayed Video Audio Setup Video Format ntsc PAL E Compression Type v MPEG 4 MIPEG E Initial Resolution D1 O cF acir MPEG 4 D1 Ver Video Ivey ich W v Quality CF Very High M very High Dual Codecs B Multi Transcoders oor Nery High Ui Very High D1 30fps v 30fps Video Frame CIF 30fps 30fps Rate QCIF 30fps 30fps E Video Channel Channel 1 E Audio In Channel Channel 1 Audio Out Channel Use Max UserCounts 10 s E Mic Sensitivity high O Low Product Infomation a Model oa Mac Address O CameraName
58. s Hep a Devi O x 2 Decor eres OR Ga S EIDE 3 Please login with administrator s authorization and move to Network page Default value for administrator login is ID admin PW 11111111 a 41 Network Camera SNC 570 Q 9 Default value is ID admin PW 11111111 Note 4 Please configure according to the network environment where SNC 570 network camera will be installed and push lt Save gt button to save the configuration Network Setup E Network Configuration IP Address 192 168 p mu NetMask 25s 255 255 0 Lan Gateway 192 E DNS1 168 126 63 i DNS2 168 126 63 2 O xDSL User Name Password DHCP E Port DDNS Configuration Connection Port 4000 default 4000 HTTP Port 80 default 80 FTP Port 21 default 21 Use DDNS DDNS Server www samsungipolis com ID Password E Continuous Jpeg Image Transmission to FTP Server Jpeg CIFs Enable FrameRate 1 Server Name Home Directory User ID User Password D Streaming Engine RTSP TCP Enable RTP UDP Enable RTP Multicast Enable Multicast IP 224 0 J JE Multicast Port 4000 Streaming Image Resolution Dl w rr 42 3 5 Network configuration and connection method using Web page LAN xDSL DHCP Configuration Network Configuration IP
59. s to 93 Network Camera SNC 570 the optimal value Set AGC to OFF and adjust the Lens VR to an appropriate brightness Adjust the Lens VR adjust the BRIGHTNESS and then check if the screen brightness changes properly Otherwise adjust the Lens VR again MANUAL Select Manual lens 5 2 2 EXPOSURE 94 MAIN SETUP 1 LENS DC J gt 2 EXPOSURE J 3 WHITE BAL ATW 4 BACKLIGHT OFF 5 SSNR ON J 6 DAY NIGHT AUTO J 7 IMAGE ADJ J 8 SPECIAL J 9 EXIT When the SETUP menu screen is displayed select EXPOSURE by using the Up and Down buttons so that the arrow indicates EXPOSURE Select a desired mode using the Up and Down buttons 5 2 How to Set Up Functions EXPOSURE SETUP SHUTTER You can select either auto or manual shutter A FLK Select this when you experience picture flicker which can happen when there is a clash with the frequency of the installed lighting ESC Select this to control the shutter speed automatically If ESC is selected the shutter speed is automatically controlled depending on the ambient illumination of the subject MANUAL You can control shutter speed manually A caution To produce better results with A FLK do not use it in conjunction with the WDR mode of the BACKLIGHT menu When the SHUTTER is set to ESC after selecting the Internal Synchronization Type the picture may become unstable if the camera faces a bright fluore
60. s to connect power cable Video output terminal This terminal is for the video output and is used to set the focus and other functions when the camera is installed GROUND terminal An earth ground terminal for camera body and peripherals 25 Network Camera SNC 570 the PoE apparatus the voltage transferred via LAN cable may be abnormally high Please contact to our distributor for installation or dismantling PoE system When you connect SNC 570 network camera to A caution 2 3 Recommended PC specifications Items Specifications CPU Intel core2 duo E4300 or higher processor Main Memory 2GB or higher RAM VGA 256M or higher recommended Os Window 2000 XP 2003 Web Browser Internet explorer 5 5 or higher Resolution 1024 768 or higher Network 10 100 Base T Ethernet DirectX 9 0C or higher 26 Ch3 Installation and Network Setup Network Camera SNC 570 3 1 Lens Installation Lenses are sold separately Lenses such as an auto iris lens CS Mount lens and C Mount lens can be used product the use of DC format auto iris lens is To effectively realize major performance of this Caution recommended Any foreign objects and fingermarks on the lens can cause inferior image quality in low light level conditions Please keep the lens clean When using an auto iris lens 1 Please peel off about 8mm of the outer skin of the auto iris lens cable Approx 8 mm 2
61. scent light Therefore take care when choosing the installation position ESC and MANUAL modes are only available together when the lens is set to MANUAL When the SHUTTER is set to MANUAL or A FLK mode SENS UP will be disabled AGC AUTO GAIN CONTROL The higher the gain level the brighter the screen but the higher the noise OFF Deactivates the AGC function 95 Network Camera SNC 570 LOW Allows automatic gain control from 0 to 30dB HIGH Allows automatic gain control from 0 to 42dB SENS UP When it is night or dark the camera automatically detects the light level and maintains a clear picture if this mode is activated Press SET to Return OFF Deactivates the SENS UP function AUTO Activates the SENS UP function RETURN Select this to save the changes in the EXPOSURE menu and return to the SETUP menu If you press the SET button in AUTO mode A You can adjust brightness by increasing or Caution decreasing the shutter speed X2 X256 Note that the higher the zoom level the brighter the screen but the more likely it is that an after image will appear Although Noise Spots and Whitish symptoms may occur in SENS UP operation when the zoom level is increased this is normal 96 5 2 How to Set Up Functions 5 2 3 WHITE BALALACE WHITE BAL Use the White Balance function to adjust the screen color 1 When the SETUP menu
62. se Web Viewer cccccessssseeeeeeeeesseeeeeees 45 4 1 How to Use Web VieWED ccccccessseeeeeeeesssseeeees 46 ATA LOGIN AR AEA E EA 46 4 1 2 Web Viewer SCIEN cccccecscccceeesseteeeeessesteeeeeees 47 4 2 Using Administration page 4 2 1 Initialization Screen after Connecting Basic Screen 53 4 2 2 4 2 3 4 2 4 4 2 5 4 2 6 4 2 7 4 2 8 4 2 9 4 2 11 Alarm Sensor 4 2 12 Time 4213 LOG arra a A r EA NEES 86 4214 Upgrade oo ecco eee ee ee 87 4 2 15 System Rebootic cnneiiinnenninke 88 Ch5 How to Operate Camera cccccssccsseceeeseeeeeeeeeesseeees 89 5 12 Setup MENU wissescesreasereteivediscecsin detest antes 90 5 2 How to Set Up Functions 91 Bi ENS mnan A aga 92 Contents D22 EXPOSURE aoia e eie aia aeea AA ieee 94 5 2 3 WHITE BALALACE WHITE BAL ceeeeeees 97 D24 BACKLIGHT a ar aa aaa a AAEE 99 5 2 5 5 2 6 5 2 7 5 2 8 5 2 9 Ch6 Troubleshooting ssssssssssssnnssnunnnnnnnnnnnnnnnsnnnnnnnnnnnnn 115 Specifications mrenea a ne BH eel tes 120 DIMENSION idide Bais aon et Nee ae na 123 O If you refer to the enclosed Quick guide and the ic Note Manual in the CD you can learn how to use Network Manager Network Camera SNC 570 Note to User This machine s electromagnetic waves have been registered as suitable for business purposes the retailer and consumer should be aware of this registration If i
63. ters 109 Network Camera SNC 570 If you move the cursor to CLR and press the 1 lt SET gt button all the letters are deleted To edit a Caution letter change the cursor to the bottom left arrow and press the lt SET gt button Move the cursor over the letter to be edited move the cursor to the letter to be inserted and then press the lt SET gt button 110 5 Enter a title move the cursor to POS and press the lt SET gt button The entered title appears on the screen Select the position to display the title on the screen by using the 4 direction buttons and press the lt SET gt button When the position is determined select END and press the lt SET gt button to return to the SPECIAL menu FRONT DOOR int ZA NI 5 at A 4 to Locatentton SET SYNC In areas where the supply is at 60Hz you can synchronize the output phase of multiple cameras using the power synchronization function Line Lock without using a synchronization signal generator INT Internal Synchronization Type L L Power Synchronization Type Line lock Press SET to Return 5 2 How to Set Up Functions Press the lt SET gt button You can select a desired phase from 0 to 359 when select phase You can decide the synchronization between luminance and color signal when select the mode When using AC power at 60Hz frequency you A can use the L L type synchronization
64. ton 5 Press the OSD button to quit OSD An item with the PH icon also has sub y nee menus To select a sub menu select an item with the icon and press the SET button An item with the icon is unavailable due to function settings 5 2 1 LENS Using this function you can control screen brightness 1 Select the lens of the DC or Video by adjusting the relevant switch on the back of the product 2 When the SETUP menu screen is displayed select LENS by using the Up and Down buttons so that the arrow indicates LENS 3 Select the connected lens type by using the Left and Right buttons DC gt MANUAL VIDEO MANUAL 92 5 2 How to Set Up Functions MAIN SETUP gt 1 LENS DC J 2 EXPOSURE d 3 WHITE BAL ATW 4 BACKLIGHT OFF 5 SSNR ON J 6 DAY NIGHT AUTO J 7 IMAGE ADJ J 8 SPECIAL J 9 EXIT DC VIDEO Auto iris lens selection When DC is selected you can control screen brightness The range of brightness control is between 1 and 70 Adjust the brightness appropriately for optimal screen brightness LENS P BRIGHTNESS ston 25 Press SET to Return Some lenses may not work properly depending A A on the setting of the BRIGHTNESS LEVEL Caution When Using a Video Type Auto Iris Lens Adjust the ALC adjustment terminal on the lens appropriately In general set it to AV Average It may not work properly depending on the installed lens Set the Level VR of the len
65. ts replacement please contact your service provider Disassembly and Cleaning e There is a risk of malfunction shock or other dangers Please do not disassemble or attempt to fix the product e To prevent malfunction or shock please do not use a wet cloth or oil based cleaning product to clean the product exterior Clean the exterior of the product with a dry cloth Caution Caution Do not install under extreme temperature conditions Use only under temperature conditions between 10 C and 50 C Provide good ventilation when using in high temperature conditions e Do not install under unstable lighting conditions Severe lighting changes or flickering may hinder normal camera operation Do not drop the camera or subject it to physical shock May cause a product malfunction e Never keep the camera face to strong light directly May damage the CCD e Avoid touching the camera lens The lens is the most important component of the camera Be careful not to smear it with fingerprints Do not expose the camera to rain or other types of liquids Wipe dry any liquids Liquids may contain minerals that are corrosive to Electronic components Do not expose the camera to radioactivity Radioactivity exposure may damage the CCD e Do not disassemble the camera If you disassemble the product as you please a Repair Center doesn t repair it for free Network Camera SNC 570 e Please c
66. ust the brightness level 116 Troubleshooting Problem Solution There is a problem with the camera operation The camera surface is too hot and black stripes appear on the screen Please check if an appropriate power source to the camera complies with the manufacturer s standard requirement or if the voltage keeps changing The MOTION DETECTION function is not working Please check if MOTION DETECTION mode is turned on Please check if the MD LEVEL is too low Please check the setting of the MD AREA Colors are not quite right Please check the WHITE BAL setting Please refer to page 97 The screen is flickering Please check if the camera is facing directly into sunlight or fluorescent light Please check if an auto iris lens is being used Please check the connection of the lens connector cable L L mode isn t able to be selected Have you connected your camera to DC power source Connect it to AC power source Please check the frequency of power supply 60Hz for NTSC 50Hz for PAL DAYNIGHT Auto mode is not working Please check if the AGC menu is set to the OFF position Network Camera SNC 570 Problem Solution SENS UP function is not working loni Please check if the AGC menu is set to the OFF position Please check if the SHUTTER menu is set to MANUAL mode Please check the limit of SENS UP AUTO mode Audio is not work
67. ut the latest video image to the users anytime despite of video loss Itis more efficient to use broadband transmission to broadcast video image for multi users simultaneously Since multicast through internet is not available you need a router to allow multicast fe Up to 10 connections at the same time may be Note regarded as one connection 59 Network Camera SNC 570 DDNS Usage Registration process of DDNS is as following O Step1 Complete the registration form in iPOLiS website The website is www samsungipolis com Nowe 2 iseia i srmn ENE a SANSUNGTECHWIN WHAT IS IPOLIS PRODUCT DDNS SERVICE SUPPORT NY IPOLIS iPOLIS Samsung Network Surveillance System Goto thelist of registered IPs sea siwase SNP SNP 1000 E orei nanaig soci _ HM OCPTZN Caron o gt a DOWNLOAD CENTER SHY OA Opazo 10009 2 Q Meters visintornoton souto fa MalbmibatonO gts Lin DaN A pote wae fl MPEG 4 IPEG VGA 30fps Zt Bidirectional aco omotoPT2 orto ae PRIVACY LEGAL NOTICE CONTACT US rawersme m GuickLnk E Figure 1 Website of iPOLIS 60 4 2 Using Administration page SIGNUP My IPOLIS gt Signup gt Welcome to IPOLIS bA We provide real time online video service for IPOLIS products through this web browser We recommend strongly every purchaser of IPOLIS products sign up for IPOLIS online LEGAL NOTICE Legal Notice a NO 1 NO 2 Agree Figure

Anywhere

Contents

Download Pdf Manuals

Related Search

Related Contents