Installation Manual EN
Contents
1. 3 Names and Functions of Parts 1 Front 0 Lens protection cap Please cover the lens when not using it CS Mount lens adaptor Please attach the CS Mount lens here 3 Back Focus clamp screw Please loosen the clamp screw with a screwdriver before adjusting the Back Focal length Mounting bracket screw hole Please use the screw hole when fixing the camera onto the mounting bracket Please use the clamp screw as specified picture 1 4 20 UNC 20 THREAD L 4 5mm 0 2mm ISO standard or 0 197 ASA standard The mounting bracket can be separated and attached to the top of the camera In this instance please do not tighten the screw to a depth of more than 5mm otherwise serious damage can occur to the inside of the camera DC12V AC24V 8 High Voltage Type D Auto iris lens connector This is the connection terminal for the auto iris lens 2 Video output terminal Sends video signals and connects to the video input terminal of the monitor 8 Power lamp Lights up when the correct power is supplied to the camera Setting button SETUP button Used for the menu display This button can be used to confirm settings after changing the value of the selected function or current conditions UP amp DOWN buttons Used for selecting items by moving the cursor up or down on the menu screen LEFT amp RIGHT buttons Used when changing item values by moving the cursor to the left or right on the menu screen2. Power input terminal Connects to the power appropriate to each power requirement Auto Iris Switch Video or DC Make sure that user can t use video type lens using high voltage camera 4 Installation 1 Lens Lenses are sold separately Lenses such as auto iris lens CS Mount lens and C Mount lens can be used Note Use of the DC auto iris lens is recommended to achieve the best results for operating this product effectively Please keep the lens clean e Any foreign objects and finger marks on the lens can cause inferior image quality in low light level conditions D When using an auto iris lens Please peel off about 8mm of the outer skin of the auto iris lens cable approx 8mm Please peel off about 2mm of the outer skin of the insulated conductor inside the lens cable Please remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug LENS Pin No DC VIDEO No 1 Pin Damping Red power No 2 Pin Damping NC No 3 Pin Drive White video signal No 4 Pin Drive Black GND 10 Lens cable No 3 Pin j No 1 Pin Please replace the auto iris lens connection plug cover and take off the lens protection cap and then attach the auto iris lens to the camera by screwing it in clockwise Please insert the connection plug that is connected to the auto iris lens cable into the auto lens connector
3. AREA DISPLAY Turn on and off the programmed privacy masking In ON mode Press the SET button to set up privacy masking Set position and area size for privacy masking using allow COLOR Setup color of the programmed motion area mask 1 15 color 5 SYNC In areas where the supply is at 60Hz NTSC 50Hz PAL you can synchronize the output phase of multiple cameras using the power synchronization function Line Lock without using a synchronization signal generator INT Internal Synchronization Type e L L Power Synchronization Type Line lock Press the SET button and you can select a desired phase between 0 and 359 Note e When using AC power at 60Hz NTSC 50Hz PAL frequency you can use the L L type 22 synchronization When the power is DC 12V the SYNC The menu is fixed to the INT mode 6 LANGUAGE It can be switched to English Korean Japanese for OSD menu 7 DEFECT When the camera has white defect in the CCD with ages user can restore it using OSD menu Sense up User can adjust white defect according to luminous condition DIFF User has to select level 1 4 according to size of the white defect If it is big you have to select high number START Before pressing the Start menu you have to cover camera lens using lens cap 8 RETURN Select this to save the SPECIAL menu settings and return to the SPECIAL menu 7 ADJUST 1 When the SETUP menu screen is displayed select IMAGE ADJ by using the Up and Dow
4. D ZOOM X1 0 lt gt X32 0 PAN Moving zoom in picture to left right TILT Moving zoom in picture to up down It doesn t work for PAN TILT when the D ZOOM is on x1 0 GAMMA Setting GAMMA curve NEG IMAGE Switching to negative color 3 MOTION MOTION AREA SELECT AREA1 AREA DISPLAY ON SENSITIVITY 1 40 MOTION VIEW ON RETURN 4 21 Motion detection function allows more effective observation When any movement is detected signal is generated ON If MOTION function is active character of person is flickering on right above position when motion is detected on selected area MOTION DETECTION Setting AREA SELECT Select the programmed area that can be set up to 4 areas AREA DISPLAY Turn on and off the programmed motion area e SENSITIVITY 1 40 Adjust motion sensitivity of the programmed motion area MOTION VIEW Turn on and off the display when motion sensitivity detected RETURN Save setup value and return to previous menu OFF Cancel Motion detection function 4 PRIVACY PRIVACY AREA SELECT AREA1 AREADISPLAY ON COLOR 1 15 RETURN Y You may conceal specific area on the screen with this PRIVACY function Select ON by pressing left right button and press SET button to enter PRIVACY mode Select ON and press SET button for PRIVACY setup menu PRIVACY Area Setting AREA SELECT Select the programmed privacy area Area 1 8
5. manufacturer s standard requirement or if the voltage keeps changing The MOTION DETECTION function is not working Please check if MOTION DETECTION mode is turned on Please check if the MD LEVEL is too low Please check the setting of the MD AREA Colors are not quite right Please check the WHITE BAL setting The screen is flickering Please check if the camera is facing directly into sunlight or fluorescent light Please check if an auto iris lens is being used Please check the connection of the lens connector cable COLOR mode is not working Please check if the AGC menu is set to the OFF position SENS UP function is not Please check if the AGC menu is set to the OFF working position Please check if the SHUTTER menu is set to MANUAL mode 24 8 Specifications Signal system Image Sensor Total Pixels Effective Pixels Resolution Scanning Frequency Shutter Speed Min Illumination Day amp Night Digital WDR White Balance Defect BLC AGC 3D DNR Privacy Zone Motion Detection Sharpness Camera Title S N Ratio Video Output Lens Mount Sync System Operating Humidity Operating Temp Dimension Weight Power Consumption Power Supply NTSC PAL 1 3 Sony Super HAD CCD 811 H X508 V 795 H X596 V 768 H X494 V 752 H X582 V Color 600 TV Lines B W 700 TV Lines with ICR 15 734KHz H 60 V 15 625KHz H 50 V FLK 1 60
6. which is located on the back of the camera CS mount adaptor Please set the lens selection switch located on the back of the camera to DC or VIDEO depending on the type of auto iris lens which is being used Free voltage Caution Make sure that user can t use video type lens using high voltage camera 11 2 When using a CS Mount lens Please take off the lens protection cap and attach the CS Mount lens to the camera by screwing it in clockwise CS mount adaptor 3 When using a C Mount lens Please take off the lens protection cap and attach the C mount adaptor C mount adaptor EN Lens protection cap 2 1 Please attach the C Mount lens to the camera by screwing it in clockwise Note Please use the specified lens connection parts as shown in the picture below The use of the wrong sized parts may cause damage to the inside of the camera or result in poor fitting Use of a lens which is too heavy affects the balance of the camera and may cause a 12 Malfunction Please use a lens that weighs less than 450g Please select Av mode if possible when adjusting the automatic light control ALC of an auto lens 2 Connecting to a monitor Please connect the video output terminal located on the back of the camera to the monitor U0001001 ru CCD Camera Monitor The connection method varies depending on the type of monitor and accessories Please refer to the user s manual f
7. 1 100 000 sec 1 50 1 100 000 sec FLK Color 0 1Lux F 1 2 0 00001Lux Sense up 256x Color Auto EXT B W On Off ATW AWB AWC Set Manual Indoor Outdoor Sense up DIFF START BLC HSBLC Low Middle High Off On Off 8 Programmable Zones 4 Programmable Zones Level 0 31 On Off More than 50dB Composite video output 75 ohm terminated C CS Mount Internal 30 96 90 RH 10 C to 50 61 W X 55 H X 104 7 D mm About 420g Max 2 5W DC 12 V 10 2V 14 5 V Dual Voltage AC24V DC12V 25 High Voltage AC 90V 250V 50 60Hz 26
8. High Resolution Day amp Night COLOR BOX CAMERA CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own experience WARNING Changes or modifications not e
9. NIGHT ONLY and NIGHT ONLY ausum AREA User can adjust BLC area size and RETURN position DEFAULT Initializing HSBLC area HLC OFF 5 D WDR Digital WDR When there are both bright and dark areas at the same time this mode makes both areas distinctive 17 OFF Deactivates the WDR function INDOOR 1 15 Digital WDR suitable for INDOOR OUTDOOR 1 15 Digital WDR suitable for OUTDOOR OFF 3 WHITE BALANCE The screen color can be adjusted by using the WHITE BALANCE function 0 Please position the arrow to point to WHITE BAL on the SETUP menu by using the UP and DOWN buttons 2 Please select the mode you wish to operate by pressing the LEFT or RIGHT button ATW Select this when the color temperature is between 2 000 K and 20 000 K AWB Select this when the color temperature is between 2 500 K and 9 500 K AWC gt SET To find the optimal setting for the current luminance environment in this mode set the point the camera towards a sheet of white paper and press the SET button If the environment changes read just it MANUAL Select this to fine tune White Balance manually Set White Balance first WHITE BAL MANUAL by using the ATW or AWB mode After that i E i gt BLUE MAMAI 4 100 switch to MANUAL mode fine tune the White RED SUERTE 400 Balance and then press the SET button RETURN RETY INDOOR Fixed setting adjusting white balance by 3 200 K OUTDOOR F
10. at the arrow indicates EXPOSURE Select a desired mode using the UP and DOWN buttons EXPOSURE gt SHUTTER AGC SENSE UP BLC D WDR RETURN 1 SHUTTER You can select either auto or manual shutter FLK Select this when you experience picture flicker which can happen when there is a clash with the frequency of the installed lighting MANUAL The shutter speed can be controlled manually Auto 1 60 FLK 1 250 1 500 1 2000 1 5000 1 10000 1 100000 x256 x128 x64 X32 x16 x8 x4 x2 selectable AUTO ALC can be selectable if the lens is manual 2 AGC Auto Gain Control OFF Deactivates the AGC function LOW Allows automatic gain control to 14 dB MIDDLE Allows automatic gain control to 28dB HIGH Allows automatic gain control to 32dB 3 SENS UP OFF Deactivates the SENS UP function AUTO Activates the SENS UP function It can be adjusted x2 x256 16 4 BLC Enables a user to directly select a desired area from a picture and to view the area more clearly OFF Not being used BLC BLC GAIN Adjust GAIN of BLC area GAIN MIDDIE LOW MIDDLE HIGH DEFAULT AREA User can adjust BLC area size and position LEFT RIGHT MM 2 RM WIDTH Mn 4 DEFAULT Initializing BLC area TOP BOTTOM IO 3 HEIGHT HINEIN 3 RETURN RET 7 BLC OFF HSBLC HSBLC LEVEL Adjusting GAIN in HSBLC area 0 8 LEVEL JIM 1 8 MODE Select a mode between ALL DAY mode MODE
11. elect an ID from A B Y Z 0 1 8 9 by using the UP DOWN LEFT and RIGHT buttons Please lock in the letters by using the SETUP button When the letter is locked in the cursor moves to the next space Please repeat the above to input the ID Note If the wrong name has been input f you press the SETUP button after moving the cursor to CLR all the letters will be erased If you want to correct a letter please move the cursor to the arrow at the bottom left of the screen and press SET Please position the cursor above the letter you wish to correct and then move the cursor on to the letter you wish to choose and press the SETUP button When a name has been chosen please select a position for the name display Please move the cursor onto POS and then press the SETUP button The name will appear at the top left corner 20 Please find the position you wish to display the name by using the 4 directional buttons and then press the SETUP button Please select END and then press the SETUP button to complete ID input 2 D EFFECT D EFFECT FREEZE MIRROR D ZOOM GAMMA NEG IMAGE RETURN e FREEZE You can view still or moving pictures MIRROR You can flip the picture MIRROR Horizontal reverse for pictures on the monitor V FLIP Vertical reverse for pictures on the monitor ROTATE diagonal reverse pictures on the monitor 180 rotation D ZOOM You can use a digital zoom
12. g video on the tu monitor in the BW mode of camera it turns RETURN on When the camera in B W mode the WHITE BALANCE is deactivated If DAY NIGHT mode is AUTO the AGC is fixed HIGH IR SMART When the IR camera uses this function can suppresses saturation of the picture that happens in the short distance from object and you can set area up that you want area 5 3D DNR This function reduces the background noise in a low luminance environment 3DNR gt LEVEL IMMA 50 RETURN RET Y s ON Activates 3DNR so that noise is reduced Set the 3DNR mode to ON and press the SET button Then you can adjust the noise reduction level OFF Deactivates 3DNR Noise is not reduced 6 SPECIAL Please position the arrow to point to SPECIAL on the SETUP menu by using the UP and DOWN buttons 19 2 Please select the mode you wish to operate by pressing the UP or DOWN button SPECIAL 1 CAM TITLE 2 D EFFECT 3 MOTION 4 PRIVACY 5 SYNC 6 LANGUAGE ENGLISH 7 DEFECT 4 8 RETURN RET Y CLR POS END CAM 000 1 CAM TITLE If the TITLE is input the camera TITLE appears on the monitor D Please position the arrow to point to CAMERA TITLE by using the UP or DOWN button 2 Please select ON by pressing the LEFT or RIGHT button 3 Please press the SET button 4 Up to 15 letters can be used for the ID Please move the cursor to the letter you wish to choose by using the UP and DOWN button S
13. ixed setting adjusting white balance by 6 300 K Note Under the following conditions the WHITE BALANCE function may not operate properly In such cases please select the AWB mode When the object s surroundings have a very high color temperature eg a clear sky and sunset When the object s surroundings are dark If the camera directly faces a fluorescent light or is installed in a place where there are considerable changes in illumination the WHITE BALANCE function may become unstable 4 DAY amp NIGHT You can display pictures in color or black and white 18 When the SETUP menu screen is displayed select DAY NIGHT by using the UP and DOWN buttons so that the arrow indicates DAY NIGHT 2 Please select the mode you wish to operate by pressing the LEFT or RIGHT button COLOR The picture is always displayed in color AUTO The mode is switched to Color in a normal environment but switches to B W mode when ambient illumination is low DELAY adjusting converting speed for COLOR gt BW DON user can adjust luminous level to DELAY III 1 63 convert from Day to Night DON HII 1 255 l N D MN 1 255 Nob user can adjust luminous level to RETURN RETZ convert from Night to Day EXT This mode allows you to apply a desired filter to external signals B W This mode allows you to apply a desired filter to external signals DAY NIGHT AUTO DAY NIGHT B W BURST If it cannot be synchronizin
14. n buttons so that the arrow indicates IMAGE ADJ 2 Select a desired mode using the Up and Down buttons SHARPNESS Adjust sharpness of the video picture MONITOR Select as kind of the monitor LCD CRT USER OSD COLOR User can select OSD color 8 RESET Resets the camera settings to the factory defaults 9 EXIT Press the SET button in the EXIT menu to save the current settings and exit the SET menu 23 7 Troubleshooting If there are problems in operation please refer to the items below If the problem persists please contact the agent you purchased this product from Problems Troubleshooting Nothing appears on the screen Please check the power connection Please check the video signal line connection Please check and make sure that the auto lens switch is set to DC VIDEO when using a VIDEO DC lens The video image is not clear Please check if the lens is clean Please clean the lens with a clean cloth or brush Please adjust the contrast feature of the monitor Please readjust the back focus of the camera The screen is dark Please adjust the contrast feature of the monitor If you have an intermediate device set the 75 Hi z properly and check the terminals Please check if an auto iris lens is being used and adjust the brightness level There is a problem with the camera operation Please check if an appropriate power source to the camera complies with the
15. or each instrument Please turn off the power when connecting 3 Connecting to power DC Power Type DC 12V 500mA Dual Type Free Voltage Type 13 5 Setup Menu Operation e Menu Structure LENS DC VIDEO MANUAL EXPOSURE SHUTTER AGC OFF LOW MIDDLE HIGH SENSE UP AUTO OFF BLC OFF BLE HSBLC D WDR OFF INDOOR OUTDOOR WHITE BAL ATW AWB AWC SET MANUAL INDOOR OUTDOOR DAY amp NIGHT AUTO EXT B W COLOR 3D DNR OFF ON SPECIAL CAM TITLE D EFFECT FREEZE MIRROR D ZOOM GAMMA NER MOTION OFF ON PRIVACY OFF ON SYNC LANGUAGE DEFECT SENSE UP DIFF START RETURN ADJUST SHARPNESS MONITOR OSD COLOR RESET FACTORY EXIT Settings D Please press the SETUP button Settings can now be made The SETUP menu is displayed on the monitor 14 2 Please select any function you wish to activate by using the UP and DOWN buttons The arrow can be moved up or down by using the UP and DOWN buttons Please position the arrow to point to the function you wish to operate Select any function you SETUP Modes can be changed wish to operate by using 1 LENS DC y er 2 EXPOSURE using e an jn M 3 WHITE BAL ATW RIGHT buttons buttons 4 DAY NIGHT COLOR 5 3DNR ON 6 SPECIAL 7 ADJUST 8 RESET 4 9 EXIT 4 3 Please press the LEFT or RIGHT button if you wish to change mode When the LEFT or RIGHT bu
16. r image even in 0 1Lux color 0 00001Lux Sens Up or lower illumination Electrical Day amp Night True Day amp Night Optional The camera identifies whether it is day or night and automatically switches to the appropriate mode depending on its environment By day the camera switches to color mode in order to maintain optimal color At night it switches to B W mode so as to obtain better picture definition Motion Detection Since the camera detects motion and generates signals without any additional external sensors you can monitor activity more efficiently by connecting the camera to an alarm device White Defect restoration When the camera has white defect in the CCD with ages User can restore it using OSD menu D WDR Built in Digital WDR 3D DNR The high performance New DSP chip dramatically reduces the gain noise in digital image processing producing clear sharp images in low lighting environment It provides the further optimized DNR performance Controlled by OSD Menu The camera can be controlled by selecting text displayed on the monitor screen Additional Functions HSBLC High Suppress Back Light Compensation SYNC INT LL SENS UP FREEZE Mirror H V FLIP ROTATE D ZOOM Negative Image Sharpness Motion Detection and Privacy functions are provided 2 Components 1 2 3 4 5 COLOR CAMERA AUTO IRIS LENS CONNECTION PLUG C MOUNT ADAPTOR L WRENCH MANUAL
17. tton is pressed available values and modes are displayed in order Please keep pressing the button until you get to the mode you wish to operate 4 Please select EXIT and then press the SETUP button to finish the setting Note If appears at the mode you wish to operate it means that there is a sub menu which can be selected by pressing the SETUP button If appears at the mode item it means that there is no mode available to be selected 1 LENS This function is used to adjust the brightness of the screen 0 When the SETUP menu is displayed on the screen please position the arrow to point to LENS by using the UP and DOWN buttons 2 Please select the type of the lens you wish to use by pressing the LEFT or RIGHT Button MANUAL MANUAL lens selection DC DC Auto Iris lens selection Video Video Iris lens selection 3 Please press the SETUP button if you wish to return to the previous menu Note In Manual Video Mode Exposure menu will be displayed like below picture on the monitor User can control Brightness level here EXPOSURE SHUTTER gt BRIGHTNESS AGC SENSE UP BLC D WDR RETURN In DC mode if you want to control Brightness level press the DC button So it will appear like below picture Adjust brightness level using Left or Right button LENS PBRIGHTNESS wem 50 RETURN RET 4 2 EXPOSURE When the SETUP menu screen is displayed select EXPOSURE by using the Up and Down buttons so th
18. xpressly approved by the manufacturer could void the user s authority to operate the equipment CAUTION To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes E Warning OB OO 00 The camera needs periodic inspection Contact an authorized technician for inspection Stop using your camera when you find a malfunction If you use your camera around smoke or unusual heat for a long time fire may be caused Do not Install the camera on a surface that can not support it Unless the surface is suitable it could cause falling or other hazards Do not hold plug with wet hands It could cause an electric shock Do not disassemble the camera It may result in fire electric shock or other hazards Do not use the camera close to a gas or oil leak It may result in fire or other hazards E Contents 1 Features 2 Components 3 Names and functions of parts 4 Installation 5 Setup Menu Operation 6 Troubleshooting 7 Specifications 1 Features Ultra High Resolution 600 TV Lines Clear image quality has been achieved by employing a double speed SONY CCD with 410 000 effective pixels which provides a horizontal resolution of 600 TV lines Excellent Sensitivity The built in high sensitivity COLOR CCD enable a clea
Download Pdf Manuals
Related Search